xref: /openbmc/u-boot/include/configs/SBx81LIFKW.h (revision 341032d3)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
4  */
5 
6 #ifndef _CONFIG_SBX81LIFKW_H
7 #define _CONFIG_SBX81LIFKW_H
8 
9 /*
10  * High Level Configuration Options (easy to change)
11  */
12 #define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
13 #define CONFIG_KW88F6281	1	/* SOC Name */
14 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
15 #define CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
16 #define CONFIG_BUILD_TARGET	"u-boot.kwb"
17 
18 /* additions for new ARM relocation support */
19 #define CONFIG_SYS_SDRAM_BASE	0x00000000
20 
21 #define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
22 #define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
23 #define CONFIG_KIRKWOOD_PCIE_INIT	/* Enable PCIE Port0 */
24 #define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
25 #define CONFIG_KIRKWOOD_GPIO	1
26 
27 #define CONFIG_MISC_INIT_R		/* call misc_init_r */
28 
29 /*
30  * NS16550 Configuration
31  */
32 #define CONFIG_SYS_NS16550
33 #define CONFIG_SYS_NS16550_SERIAL
34 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
35 #define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
36 #define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
37 
38 /*
39  * Serial Port configuration
40  * The following definitions let you select what serial you want to use
41  * for your console driver.
42  */
43 
44 #define CONFIG_CONS_INDEX	1	/*Console on UART0 */
45 
46 /*
47  * For booting Linux, the board info and command line data
48  * have to be in the first 8 MB of memory, since this is
49  * the maximum mapped by the Linux kernel during initialization.
50  */
51 #define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs */
52 #define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
53 #define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
54 
55 #define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
56 #define MTDPARTS_MTDOOPS "errlog"
57 #define CONFIG_DOS_PARTITION
58 
59 /*
60  *  Environment variables configurations
61  */
62 #define CONFIG_ENV_SPI_BUS		0
63 #define CONFIG_ENV_SPI_CS		0
64 #define CONFIG_ENV_SPI_MAX_HZ		20000000	/* 20Mhz */
65 #define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
66 #define CONFIG_ENV_SECT_SIZE		0x40000		/* 256K */
67 #define CONFIG_ENV_SIZE			0x02000
68 #define CONFIG_ENV_OFFSET		0xc0000		/* env starts here - 768K */
69 
70 /*
71  * U-Boot bootcode configuration
72  */
73 
74 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for monitor */
75 #define CONFIG_SYS_MALLOC_LEN		  (4 << 20)	/* Reserve 4.0 MB for malloc */
76 
77 /*
78  * For booting Linux, the board info and command line data
79  * have to be in the first 8 MB of memory, since this is
80  * the maximum mapped by the Linux kernel during initialization.
81  */
82 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Mem map for Linux*/
83 
84 /* size in bytes reserved for initial data */
85 
86 #include <asm/arch/config.h>
87 /* There is no PHY directly connected so don't ask it for link status */
88 #undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
89 
90 /*
91  * Other required minimal configurations
92  */
93 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
94 #define CONFIG_NR_DRAM_BANKS	4
95 #define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
96 #define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
97 #define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
98 
99 /*
100  * Ethernet Driver configuration
101  */
102 #ifdef CONFIG_CMD_NET
103 #define CONFIG_NETCONSOLE	/* include NetConsole support */
104 #define CONFIG_NET_MULTI	/* specify more that one ports available */
105 #define CONFIG_MII		/* expose smi over miiphy interface */
106 #define CONFIG_MVGBE	/* Enable kirkwood Gbe Controller Driver */
107 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable a single port */
108 #define CONFIG_PHY_BASE_ADR	0x01
109 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
110 #endif /* CONFIG_CMD_NET */
111 
112 #define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
113 
114 #endif /* _CONFIG_SBX81LIFKW_H */
115