1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #ifdef CONFIG_RAMBOOT_PBL 15 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 16 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 19 #endif 20 21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 22 /* Set 1M boot space */ 23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 25 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 27 #define CONFIG_SYS_NO_FLASH 28 #endif 29 30 /* High Level Configuration Options */ 31 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 32 #define CONFIG_MP /* support multiple processors */ 33 34 #ifndef CONFIG_SYS_TEXT_BASE 35 #define CONFIG_SYS_TEXT_BASE 0xeff40000 36 #endif 37 38 #ifndef CONFIG_RESET_VECTOR_ADDRESS 39 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 40 #endif 41 42 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 43 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 44 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 45 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 46 #define CONFIG_PCIE1 /* PCIE controller 1 */ 47 #define CONFIG_PCIE2 /* PCIE controller 2 */ 48 #define CONFIG_PCIE3 /* PCIE controller 3 */ 49 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 50 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 51 52 #define CONFIG_SYS_SRIO 53 #define CONFIG_SRIO1 /* SRIO port 1 */ 54 #define CONFIG_SRIO2 /* SRIO port 2 */ 55 #define CONFIG_SRIO_PCIE_BOOT_MASTER 56 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 57 58 #define CONFIG_ENV_OVERWRITE 59 60 #ifdef CONFIG_SYS_NO_FLASH 61 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 62 #define CONFIG_ENV_IS_NOWHERE 63 #endif 64 #else 65 #define CONFIG_FLASH_CFI_DRIVER 66 #define CONFIG_SYS_FLASH_CFI 67 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 68 #endif 69 70 #if defined(CONFIG_SPIFLASH) 71 #define CONFIG_SYS_EXTRA_ENV_RELOC 72 #define CONFIG_ENV_IS_IN_SPI_FLASH 73 #define CONFIG_ENV_SPI_BUS 0 74 #define CONFIG_ENV_SPI_CS 0 75 #define CONFIG_ENV_SPI_MAX_HZ 10000000 76 #define CONFIG_ENV_SPI_MODE 0 77 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 78 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 79 #define CONFIG_ENV_SECT_SIZE 0x10000 80 #elif defined(CONFIG_SDCARD) 81 #define CONFIG_SYS_EXTRA_ENV_RELOC 82 #define CONFIG_ENV_IS_IN_MMC 83 #define CONFIG_FSL_FIXED_MMC_LOCATION 84 #define CONFIG_SYS_MMC_ENV_DEV 0 85 #define CONFIG_ENV_SIZE 0x2000 86 #define CONFIG_ENV_OFFSET (512 * 1658) 87 #elif defined(CONFIG_NAND) 88 #define CONFIG_SYS_EXTRA_ENV_RELOC 89 #define CONFIG_ENV_IS_IN_NAND 90 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 91 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 92 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 93 #define CONFIG_ENV_IS_IN_REMOTE 94 #define CONFIG_ENV_ADDR 0xffe20000 95 #define CONFIG_ENV_SIZE 0x2000 96 #elif defined(CONFIG_ENV_IS_NOWHERE) 97 #define CONFIG_ENV_SIZE 0x2000 98 #else 99 #define CONFIG_ENV_IS_IN_FLASH 100 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 101 - CONFIG_ENV_SECT_SIZE) 102 #define CONFIG_ENV_SIZE 0x2000 103 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 104 #endif 105 106 #ifndef __ASSEMBLY__ 107 unsigned long get_board_sys_clk(unsigned long dummy); 108 #endif 109 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 110 111 /* 112 * These can be toggled for performance analysis, otherwise use default. 113 */ 114 #define CONFIG_SYS_CACHE_STASHING 115 #define CONFIG_BACKSIDE_L2_CACHE 116 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 117 #define CONFIG_BTB /* toggle branch predition */ 118 119 #define CONFIG_ENABLE_36BIT_PHYS 120 121 #ifdef CONFIG_PHYS_64BIT 122 #define CONFIG_ADDR_MAP 123 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 124 #endif 125 126 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 127 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 128 #define CONFIG_SYS_MEMTEST_END 0x00400000 129 #define CONFIG_SYS_ALT_MEMTEST 130 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 131 132 /* 133 * Config the L3 Cache as L3 SRAM 134 */ 135 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 136 #ifdef CONFIG_PHYS_64BIT 137 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 138 CONFIG_RAMBOOT_TEXT_BASE) 139 #else 140 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 141 #endif 142 #define CONFIG_SYS_L3_SIZE (1024 << 10) 143 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 144 145 #ifdef CONFIG_PHYS_64BIT 146 #define CONFIG_SYS_DCSRBAR 0xf0000000 147 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 148 #endif 149 150 /* EEPROM */ 151 #define CONFIG_ID_EEPROM 152 #define CONFIG_SYS_I2C_EEPROM_NXID 153 #define CONFIG_SYS_EEPROM_BUS_NUM 0 154 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 155 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 156 157 /* 158 * DDR Setup 159 */ 160 #define CONFIG_VERY_BIG_RAM 161 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 162 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 163 164 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 165 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 166 167 #define CONFIG_DDR_SPD 168 169 #define CONFIG_SYS_SPD_BUS_NUM 0 170 #define SPD_EEPROM_ADDRESS 0x52 171 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 172 173 /* 174 * Local Bus Definitions 175 */ 176 177 /* Set the local bus clock 1/8 of platform clock */ 178 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 179 180 /* 181 * This board doesn't have a promjet connector. 182 * However, it uses commone corenet board LAW and TLB. 183 * It is necessary to use the same start address with proper offset. 184 */ 185 #define CONFIG_SYS_FLASH_BASE 0xe0000000 186 #ifdef CONFIG_PHYS_64BIT 187 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 188 #else 189 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 190 #endif 191 192 #define CONFIG_SYS_FLASH_BR_PRELIM \ 193 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 194 BR_PS_16 | BR_V) 195 #define CONFIG_SYS_FLASH_OR_PRELIM \ 196 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 197 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 198 199 #define CONFIG_FSL_CPLD 200 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 201 #ifdef CONFIG_PHYS_64BIT 202 #define CPLD_BASE_PHYS 0xfffdf0000ull 203 #else 204 #define CPLD_BASE_PHYS CPLD_BASE 205 #endif 206 207 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 208 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 209 210 #define PIXIS_LBMAP_SWITCH 7 211 #define PIXIS_LBMAP_MASK 0xf0 212 #define PIXIS_LBMAP_SHIFT 4 213 #define PIXIS_LBMAP_ALTBANK 0x40 214 215 #define CONFIG_SYS_FLASH_QUIET_TEST 216 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 217 218 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 219 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 220 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 221 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 222 223 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 224 225 #if defined(CONFIG_RAMBOOT_PBL) 226 #define CONFIG_SYS_RAMBOOT 227 #endif 228 229 #define CONFIG_NAND_FSL_ELBC 230 /* Nand Flash */ 231 #ifdef CONFIG_NAND_FSL_ELBC 232 #define CONFIG_SYS_NAND_BASE 0xffa00000 233 #ifdef CONFIG_PHYS_64BIT 234 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 235 #else 236 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 237 #endif 238 239 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 240 #define CONFIG_SYS_MAX_NAND_DEVICE 1 241 #define CONFIG_CMD_NAND 242 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 243 244 /* NAND flash config */ 245 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 246 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 247 | BR_PS_8 /* Port Size = 8 bit */ \ 248 | BR_MS_FCM /* MSEL = FCM */ \ 249 | BR_V) /* valid */ 250 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 251 | OR_FCM_PGS /* Large Page*/ \ 252 | OR_FCM_CSCT \ 253 | OR_FCM_CST \ 254 | OR_FCM_CHT \ 255 | OR_FCM_SCY_1 \ 256 | OR_FCM_TRLX \ 257 | OR_FCM_EHTR) 258 259 #ifdef CONFIG_NAND 260 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 261 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 262 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 263 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 264 #else 265 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 266 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 267 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 268 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 269 #endif 270 #else 271 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 272 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 273 #endif /* CONFIG_NAND_FSL_ELBC */ 274 275 #define CONFIG_SYS_FLASH_EMPTY_INFO 276 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 277 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 278 279 #define CONFIG_BOARD_EARLY_INIT_F 280 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 281 #define CONFIG_MISC_INIT_R 282 283 #define CONFIG_HWCONFIG 284 285 /* define to use L1 as initial stack */ 286 #define CONFIG_L1_INIT_RAM 287 #define CONFIG_SYS_INIT_RAM_LOCK 288 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 289 #ifdef CONFIG_PHYS_64BIT 290 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 291 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 292 /* The assembler doesn't like typecast */ 293 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 294 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 295 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 296 #else 297 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 298 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 299 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 300 #endif 301 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 302 303 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 304 GENERATED_GBL_DATA_SIZE) 305 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 306 307 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 308 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 309 310 /* Serial Port - controlled on board with jumper J8 311 * open - index 2 312 * shorted - index 1 313 */ 314 #define CONFIG_CONS_INDEX 1 315 #define CONFIG_SYS_NS16550_SERIAL 316 #define CONFIG_SYS_NS16550_REG_SIZE 1 317 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 318 319 #define CONFIG_SYS_BAUDRATE_TABLE \ 320 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 321 322 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 323 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 324 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 325 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 326 327 /* I2C */ 328 #define CONFIG_SYS_I2C 329 #define CONFIG_SYS_I2C_FSL 330 #define CONFIG_SYS_FSL_I2C_SPEED 400000 331 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 332 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 333 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 334 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 335 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 336 337 /* 338 * RapidIO 339 */ 340 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 341 #ifdef CONFIG_PHYS_64BIT 342 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 343 #else 344 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 345 #endif 346 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 347 348 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 349 #ifdef CONFIG_PHYS_64BIT 350 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 351 #else 352 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 353 #endif 354 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 355 356 /* 357 * for slave u-boot IMAGE instored in master memory space, 358 * PHYS must be aligned based on the SIZE 359 */ 360 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 361 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 362 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 363 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 364 /* 365 * for slave UCODE and ENV instored in master memory space, 366 * PHYS must be aligned based on the SIZE 367 */ 368 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 369 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 370 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 371 372 /* slave core release by master*/ 373 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 374 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 375 376 /* 377 * SRIO_PCIE_BOOT - SLAVE 378 */ 379 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 380 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 381 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 382 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 383 #endif 384 385 /* 386 * eSPI - Enhanced SPI 387 */ 388 #define CONFIG_SF_DEFAULT_SPEED 10000000 389 #define CONFIG_SF_DEFAULT_MODE 0 390 391 /* 392 * General PCI 393 * Memory space is mapped 1-1, but I/O space must start from 0. 394 */ 395 396 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 397 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 398 #ifdef CONFIG_PHYS_64BIT 399 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 400 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 401 #else 402 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 403 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 404 #endif 405 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 406 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 407 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 408 #ifdef CONFIG_PHYS_64BIT 409 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 410 #else 411 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 412 #endif 413 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 414 415 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 416 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 417 #ifdef CONFIG_PHYS_64BIT 418 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 419 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 420 #else 421 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 422 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 423 #endif 424 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 425 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 426 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 427 #ifdef CONFIG_PHYS_64BIT 428 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 429 #else 430 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 431 #endif 432 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 433 434 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 435 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 436 #ifdef CONFIG_PHYS_64BIT 437 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 438 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 439 #else 440 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 441 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 442 #endif 443 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 444 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 445 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 446 #ifdef CONFIG_PHYS_64BIT 447 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 448 #else 449 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 450 #endif 451 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 452 453 /* Qman/Bman */ 454 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 455 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 456 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 457 #ifdef CONFIG_PHYS_64BIT 458 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 459 #else 460 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 461 #endif 462 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 463 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 464 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 465 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 466 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 467 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 468 CONFIG_SYS_BMAN_CENA_SIZE) 469 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 470 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 471 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 472 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 473 #ifdef CONFIG_PHYS_64BIT 474 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 475 #else 476 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 477 #endif 478 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 479 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 480 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 481 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 482 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 483 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 484 CONFIG_SYS_QMAN_CENA_SIZE) 485 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 486 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 487 488 #define CONFIG_SYS_DPAA_FMAN 489 #define CONFIG_SYS_DPAA_PME 490 /* Default address of microcode for the Linux Fman driver */ 491 #if defined(CONFIG_SPIFLASH) 492 /* 493 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 494 * env, so we got 0x110000. 495 */ 496 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 497 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 498 #elif defined(CONFIG_SDCARD) 499 /* 500 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 501 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 502 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 503 */ 504 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 505 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 506 #elif defined(CONFIG_NAND) 507 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 508 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 509 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 510 /* 511 * Slave has no ucode locally, it can fetch this from remote. When implementing 512 * in two corenet boards, slave's ucode could be stored in master's memory 513 * space, the address can be mapped from slave TLB->slave LAW-> 514 * slave SRIO or PCIE outbound window->master inbound window-> 515 * master LAW->the ucode address in master's memory space. 516 */ 517 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 518 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 519 #else 520 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 521 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 522 #endif 523 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 524 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 525 526 #ifdef CONFIG_SYS_DPAA_FMAN 527 #define CONFIG_FMAN_ENET 528 #define CONFIG_PHYLIB_10G 529 #define CONFIG_PHY_VITESSE 530 #define CONFIG_PHY_TERANETICS 531 #endif 532 533 #ifdef CONFIG_PCI 534 #define CONFIG_PCI_INDIRECT_BRIDGE 535 536 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 537 #define CONFIG_DOS_PARTITION 538 #endif /* CONFIG_PCI */ 539 540 /* SATA */ 541 #define CONFIG_FSL_SATA_V2 542 543 #ifdef CONFIG_FSL_SATA_V2 544 #define CONFIG_FSL_SATA 545 #define CONFIG_LIBATA 546 547 #define CONFIG_SYS_SATA_MAX_DEVICE 2 548 #define CONFIG_SATA1 549 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 550 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 551 #define CONFIG_SATA2 552 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 553 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 554 555 #define CONFIG_LBA48 556 #define CONFIG_CMD_SATA 557 #define CONFIG_DOS_PARTITION 558 #endif 559 560 #ifdef CONFIG_FMAN_ENET 561 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 562 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 563 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 564 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 565 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 566 567 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 568 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 569 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 570 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 571 572 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 573 574 #define CONFIG_SYS_TBIPA_VALUE 8 575 #define CONFIG_MII /* MII PHY management */ 576 #define CONFIG_ETHPRIME "FM1@DTSEC1" 577 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 578 #endif 579 580 /* 581 * Environment 582 */ 583 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 584 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 585 586 /* 587 * Command line configuration. 588 */ 589 #define CONFIG_CMD_ERRATA 590 #define CONFIG_CMD_IRQ 591 592 #ifdef CONFIG_PCI 593 #define CONFIG_CMD_PCI 594 #endif 595 596 /* 597 * USB 598 */ 599 #define CONFIG_HAS_FSL_DR_USB 600 #define CONFIG_HAS_FSL_MPH_USB 601 602 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 603 #define CONFIG_USB_EHCI 604 #define CONFIG_USB_EHCI_FSL 605 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 606 #endif 607 608 #ifdef CONFIG_MMC 609 #define CONFIG_FSL_ESDHC 610 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 611 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 612 #define CONFIG_GENERIC_MMC 613 #define CONFIG_DOS_PARTITION 614 #endif 615 616 /* Hash command with SHA acceleration supported in hardware */ 617 #ifdef CONFIG_FSL_CAAM 618 #define CONFIG_CMD_HASH 619 #define CONFIG_SHA_HW_ACCEL 620 #endif 621 622 /* 623 * Miscellaneous configurable options 624 */ 625 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 626 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 627 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 628 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 629 #ifdef CONFIG_CMD_KGDB 630 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 631 #else 632 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 633 #endif 634 /* Print Buffer Size */ 635 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 636 sizeof(CONFIG_SYS_PROMPT)+16) 637 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 638 /* Boot Argument Buffer Size */ 639 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 640 641 /* 642 * For booting Linux, the board info and command line data 643 * have to be in the first 64 MB of memory, since this is 644 * the maximum mapped by the Linux kernel during initialization. 645 */ 646 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 647 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 648 649 #ifdef CONFIG_CMD_KGDB 650 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 651 #endif 652 653 /* 654 * Environment Configuration 655 */ 656 #define CONFIG_ROOTPATH "/opt/nfsroot" 657 #define CONFIG_BOOTFILE "uImage" 658 #define CONFIG_UBOOTPATH u-boot.bin 659 660 /* default location for tftp and bootm */ 661 #define CONFIG_LOADADDR 1000000 662 663 664 #define CONFIG_BAUDRATE 115200 665 666 #define __USB_PHY_TYPE utmi 667 668 #define CONFIG_EXTRA_ENV_SETTINGS \ 669 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 670 "bank_intlv=cs0_cs1\0" \ 671 "netdev=eth0\0" \ 672 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 673 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 674 "tftpflash=tftpboot $loadaddr $uboot && " \ 675 "protect off $ubootaddr +$filesize && " \ 676 "erase $ubootaddr +$filesize && " \ 677 "cp.b $loadaddr $ubootaddr $filesize && " \ 678 "protect on $ubootaddr +$filesize && " \ 679 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 680 "consoledev=ttyS0\0" \ 681 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 682 "usb_dr_mode=host\0" \ 683 "ramdiskaddr=2000000\0" \ 684 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 685 "fdtaddr=1e00000\0" \ 686 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 687 "bdev=sda3\0" 688 689 #define CONFIG_HDBOOT \ 690 "setenv bootargs root=/dev/$bdev rw " \ 691 "console=$consoledev,$baudrate $othbootargs;" \ 692 "tftp $loadaddr $bootfile;" \ 693 "tftp $fdtaddr $fdtfile;" \ 694 "bootm $loadaddr - $fdtaddr" 695 696 #define CONFIG_NFSBOOTCOMMAND \ 697 "setenv bootargs root=/dev/nfs rw " \ 698 "nfsroot=$serverip:$rootpath " \ 699 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 700 "console=$consoledev,$baudrate $othbootargs;" \ 701 "tftp $loadaddr $bootfile;" \ 702 "tftp $fdtaddr $fdtfile;" \ 703 "bootm $loadaddr - $fdtaddr" 704 705 #define CONFIG_RAMBOOTCOMMAND \ 706 "setenv bootargs root=/dev/ram rw " \ 707 "console=$consoledev,$baudrate $othbootargs;" \ 708 "tftp $ramdiskaddr $ramdiskfile;" \ 709 "tftp $loadaddr $bootfile;" \ 710 "tftp $fdtaddr $fdtfile;" \ 711 "bootm $loadaddr $ramdiskaddr $fdtaddr" 712 713 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 714 715 #include <asm/fsl_secure_boot.h> 716 717 #endif /* __CONFIG_H */ 718