1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_P2041RDB 15 #define CONFIG_PHYS_64BIT 16 #define CONFIG_SYS_GENERIC_BOARD 17 #define CONFIG_DISPLAY_BOARDINFO 18 #define CONFIG_PPC_P2041 19 20 #ifdef CONFIG_RAMBOOT_PBL 21 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 22 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 23 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 24 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 25 #endif 26 27 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 28 /* Set 1M boot space */ 29 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 30 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 31 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 32 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 33 #define CONFIG_SYS_NO_FLASH 34 #endif 35 36 /* High Level Configuration Options */ 37 #define CONFIG_BOOKE 38 #define CONFIG_E500 /* BOOKE e500 family */ 39 #define CONFIG_E500MC /* BOOKE e500mc family */ 40 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 41 #define CONFIG_MP /* support multiple processors */ 42 43 #ifndef CONFIG_SYS_TEXT_BASE 44 #define CONFIG_SYS_TEXT_BASE 0xeff40000 45 #endif 46 47 #ifndef CONFIG_RESET_VECTOR_ADDRESS 48 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 49 #endif 50 51 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 52 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 53 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 54 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 55 #define CONFIG_PCI /* Enable PCI/PCIE */ 56 #define CONFIG_PCIE1 /* PCIE controler 1 */ 57 #define CONFIG_PCIE2 /* PCIE controler 2 */ 58 #define CONFIG_PCIE3 /* PCIE controler 3 */ 59 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 60 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 61 62 #define CONFIG_SYS_SRIO 63 #define CONFIG_SRIO1 /* SRIO port 1 */ 64 #define CONFIG_SRIO2 /* SRIO port 2 */ 65 #define CONFIG_SRIO_PCIE_BOOT_MASTER 66 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 67 68 #define CONFIG_FSL_LAW /* Use common FSL init code */ 69 70 #define CONFIG_ENV_OVERWRITE 71 72 #ifdef CONFIG_SYS_NO_FLASH 73 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 74 #define CONFIG_ENV_IS_NOWHERE 75 #endif 76 #else 77 #define CONFIG_FLASH_CFI_DRIVER 78 #define CONFIG_SYS_FLASH_CFI 79 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 80 #endif 81 82 #if defined(CONFIG_SPIFLASH) 83 #define CONFIG_SYS_EXTRA_ENV_RELOC 84 #define CONFIG_ENV_IS_IN_SPI_FLASH 85 #define CONFIG_ENV_SPI_BUS 0 86 #define CONFIG_ENV_SPI_CS 0 87 #define CONFIG_ENV_SPI_MAX_HZ 10000000 88 #define CONFIG_ENV_SPI_MODE 0 89 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 90 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 91 #define CONFIG_ENV_SECT_SIZE 0x10000 92 #elif defined(CONFIG_SDCARD) 93 #define CONFIG_SYS_EXTRA_ENV_RELOC 94 #define CONFIG_ENV_IS_IN_MMC 95 #define CONFIG_FSL_FIXED_MMC_LOCATION 96 #define CONFIG_SYS_MMC_ENV_DEV 0 97 #define CONFIG_ENV_SIZE 0x2000 98 #define CONFIG_ENV_OFFSET (512 * 1658) 99 #elif defined(CONFIG_NAND) 100 #define CONFIG_SYS_EXTRA_ENV_RELOC 101 #define CONFIG_ENV_IS_IN_NAND 102 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 103 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 104 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 105 #define CONFIG_ENV_IS_IN_REMOTE 106 #define CONFIG_ENV_ADDR 0xffe20000 107 #define CONFIG_ENV_SIZE 0x2000 108 #elif defined(CONFIG_ENV_IS_NOWHERE) 109 #define CONFIG_ENV_SIZE 0x2000 110 #else 111 #define CONFIG_ENV_IS_IN_FLASH 112 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 113 - CONFIG_ENV_SECT_SIZE) 114 #define CONFIG_ENV_SIZE 0x2000 115 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 116 #endif 117 118 #ifndef __ASSEMBLY__ 119 unsigned long get_board_sys_clk(unsigned long dummy); 120 #endif 121 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 122 123 /* 124 * These can be toggled for performance analysis, otherwise use default. 125 */ 126 #define CONFIG_SYS_CACHE_STASHING 127 #define CONFIG_BACKSIDE_L2_CACHE 128 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 129 #define CONFIG_BTB /* toggle branch predition */ 130 131 #define CONFIG_ENABLE_36BIT_PHYS 132 133 #ifdef CONFIG_PHYS_64BIT 134 #define CONFIG_ADDR_MAP 135 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 136 #endif 137 138 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 139 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 140 #define CONFIG_SYS_MEMTEST_END 0x00400000 141 #define CONFIG_SYS_ALT_MEMTEST 142 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 143 144 /* 145 * Config the L3 Cache as L3 SRAM 146 */ 147 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 148 #ifdef CONFIG_PHYS_64BIT 149 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 150 CONFIG_RAMBOOT_TEXT_BASE) 151 #else 152 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 153 #endif 154 #define CONFIG_SYS_L3_SIZE (1024 << 10) 155 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 156 157 #ifdef CONFIG_PHYS_64BIT 158 #define CONFIG_SYS_DCSRBAR 0xf0000000 159 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 160 #endif 161 162 /* EEPROM */ 163 #define CONFIG_ID_EEPROM 164 #define CONFIG_SYS_I2C_EEPROM_NXID 165 #define CONFIG_SYS_EEPROM_BUS_NUM 0 166 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 167 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 168 169 /* 170 * DDR Setup 171 */ 172 #define CONFIG_VERY_BIG_RAM 173 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 174 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 175 176 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 177 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 178 179 #define CONFIG_DDR_SPD 180 #define CONFIG_SYS_FSL_DDR3 181 182 #define CONFIG_SYS_SPD_BUS_NUM 0 183 #define SPD_EEPROM_ADDRESS 0x52 184 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 185 186 /* 187 * Local Bus Definitions 188 */ 189 190 /* Set the local bus clock 1/8 of platform clock */ 191 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 192 193 /* 194 * This board doesn't have a promjet connector. 195 * However, it uses commone corenet board LAW and TLB. 196 * It is necessary to use the same start address with proper offset. 197 */ 198 #define CONFIG_SYS_FLASH_BASE 0xe0000000 199 #ifdef CONFIG_PHYS_64BIT 200 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 201 #else 202 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 203 #endif 204 205 #define CONFIG_SYS_FLASH_BR_PRELIM \ 206 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 207 BR_PS_16 | BR_V) 208 #define CONFIG_SYS_FLASH_OR_PRELIM \ 209 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 210 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 211 212 #define CONFIG_FSL_CPLD 213 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 214 #ifdef CONFIG_PHYS_64BIT 215 #define CPLD_BASE_PHYS 0xfffdf0000ull 216 #else 217 #define CPLD_BASE_PHYS CPLD_BASE 218 #endif 219 220 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 221 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 222 223 #define PIXIS_LBMAP_SWITCH 7 224 #define PIXIS_LBMAP_MASK 0xf0 225 #define PIXIS_LBMAP_SHIFT 4 226 #define PIXIS_LBMAP_ALTBANK 0x40 227 228 #define CONFIG_SYS_FLASH_QUIET_TEST 229 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 230 231 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 232 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 233 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 234 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 235 236 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 237 238 #if defined(CONFIG_RAMBOOT_PBL) 239 #define CONFIG_SYS_RAMBOOT 240 #endif 241 242 #define CONFIG_NAND_FSL_ELBC 243 /* Nand Flash */ 244 #ifdef CONFIG_NAND_FSL_ELBC 245 #define CONFIG_SYS_NAND_BASE 0xffa00000 246 #ifdef CONFIG_PHYS_64BIT 247 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 248 #else 249 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 250 #endif 251 252 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 253 #define CONFIG_SYS_MAX_NAND_DEVICE 1 254 #define CONFIG_CMD_NAND 255 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 256 257 /* NAND flash config */ 258 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 259 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 260 | BR_PS_8 /* Port Size = 8 bit */ \ 261 | BR_MS_FCM /* MSEL = FCM */ \ 262 | BR_V) /* valid */ 263 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 264 | OR_FCM_PGS /* Large Page*/ \ 265 | OR_FCM_CSCT \ 266 | OR_FCM_CST \ 267 | OR_FCM_CHT \ 268 | OR_FCM_SCY_1 \ 269 | OR_FCM_TRLX \ 270 | OR_FCM_EHTR) 271 272 #ifdef CONFIG_NAND 273 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 274 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 275 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 276 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 277 #else 278 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 279 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 280 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 281 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 282 #endif 283 #else 284 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 285 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 286 #endif /* CONFIG_NAND_FSL_ELBC */ 287 288 #define CONFIG_SYS_FLASH_EMPTY_INFO 289 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 290 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 291 292 #define CONFIG_BOARD_EARLY_INIT_F 293 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 294 #define CONFIG_MISC_INIT_R 295 296 #define CONFIG_HWCONFIG 297 298 /* define to use L1 as initial stack */ 299 #define CONFIG_L1_INIT_RAM 300 #define CONFIG_SYS_INIT_RAM_LOCK 301 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 302 #ifdef CONFIG_PHYS_64BIT 303 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 304 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 305 /* The assembler doesn't like typecast */ 306 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 307 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 308 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 309 #else 310 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 311 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 312 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 313 #endif 314 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 315 316 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 317 GENERATED_GBL_DATA_SIZE) 318 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 319 320 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 321 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 322 323 /* Serial Port - controlled on board with jumper J8 324 * open - index 2 325 * shorted - index 1 326 */ 327 #define CONFIG_CONS_INDEX 1 328 #define CONFIG_SYS_NS16550 329 #define CONFIG_SYS_NS16550_SERIAL 330 #define CONFIG_SYS_NS16550_REG_SIZE 1 331 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 332 333 #define CONFIG_SYS_BAUDRATE_TABLE \ 334 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 335 336 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 337 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 338 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 339 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 340 341 /* Use the HUSH parser */ 342 #define CONFIG_SYS_HUSH_PARSER 343 344 /* pass open firmware flat tree */ 345 #define CONFIG_OF_LIBFDT 346 #define CONFIG_OF_BOARD_SETUP 347 #define CONFIG_OF_STDOUT_VIA_ALIAS 348 349 /* new uImage format support */ 350 #define CONFIG_FIT 351 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 352 353 /* I2C */ 354 #define CONFIG_SYS_I2C 355 #define CONFIG_SYS_I2C_FSL 356 #define CONFIG_SYS_FSL_I2C_SPEED 400000 357 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 358 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 359 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 360 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 361 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 362 363 /* 364 * RapidIO 365 */ 366 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 367 #ifdef CONFIG_PHYS_64BIT 368 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 369 #else 370 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 371 #endif 372 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 373 374 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 375 #ifdef CONFIG_PHYS_64BIT 376 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 377 #else 378 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 379 #endif 380 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 381 382 /* 383 * for slave u-boot IMAGE instored in master memory space, 384 * PHYS must be aligned based on the SIZE 385 */ 386 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 387 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 388 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 389 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 390 /* 391 * for slave UCODE and ENV instored in master memory space, 392 * PHYS must be aligned based on the SIZE 393 */ 394 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 395 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 396 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 397 398 /* slave core release by master*/ 399 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 400 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 401 402 /* 403 * SRIO_PCIE_BOOT - SLAVE 404 */ 405 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 406 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 407 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 408 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 409 #endif 410 411 /* 412 * eSPI - Enhanced SPI 413 */ 414 #define CONFIG_FSL_ESPI 415 #define CONFIG_SPI_FLASH 416 #define CONFIG_SPI_FLASH_SPANSION 417 #define CONFIG_CMD_SF 418 #define CONFIG_SF_DEFAULT_SPEED 10000000 419 #define CONFIG_SF_DEFAULT_MODE 0 420 421 /* 422 * General PCI 423 * Memory space is mapped 1-1, but I/O space must start from 0. 424 */ 425 426 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 427 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 428 #ifdef CONFIG_PHYS_64BIT 429 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 430 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 431 #else 432 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 433 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 434 #endif 435 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 436 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 437 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 438 #ifdef CONFIG_PHYS_64BIT 439 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 440 #else 441 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 442 #endif 443 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 444 445 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 446 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 447 #ifdef CONFIG_PHYS_64BIT 448 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 449 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 450 #else 451 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 452 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 453 #endif 454 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 455 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 456 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 457 #ifdef CONFIG_PHYS_64BIT 458 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 459 #else 460 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 461 #endif 462 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 463 464 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 465 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 466 #ifdef CONFIG_PHYS_64BIT 467 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 468 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 469 #else 470 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 471 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 472 #endif 473 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 474 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 475 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 476 #ifdef CONFIG_PHYS_64BIT 477 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 478 #else 479 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 480 #endif 481 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 482 483 /* Qman/Bman */ 484 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 485 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 486 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 487 #ifdef CONFIG_PHYS_64BIT 488 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 489 #else 490 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 491 #endif 492 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 493 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 494 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 495 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 496 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 497 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 498 CONFIG_SYS_BMAN_CENA_SIZE) 499 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 500 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 501 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 502 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 503 #ifdef CONFIG_PHYS_64BIT 504 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 505 #else 506 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 507 #endif 508 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 509 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 510 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 511 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 512 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 513 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 514 CONFIG_SYS_QMAN_CENA_SIZE) 515 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 516 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 517 518 #define CONFIG_SYS_DPAA_FMAN 519 #define CONFIG_SYS_DPAA_PME 520 /* Default address of microcode for the Linux Fman driver */ 521 #if defined(CONFIG_SPIFLASH) 522 /* 523 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 524 * env, so we got 0x110000. 525 */ 526 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 527 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 528 #elif defined(CONFIG_SDCARD) 529 /* 530 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 531 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 532 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 533 */ 534 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 535 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 536 #elif defined(CONFIG_NAND) 537 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 538 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 539 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 540 /* 541 * Slave has no ucode locally, it can fetch this from remote. When implementing 542 * in two corenet boards, slave's ucode could be stored in master's memory 543 * space, the address can be mapped from slave TLB->slave LAW-> 544 * slave SRIO or PCIE outbound window->master inbound window-> 545 * master LAW->the ucode address in master's memory space. 546 */ 547 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 548 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 549 #else 550 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 551 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 552 #endif 553 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 554 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 555 556 #ifdef CONFIG_SYS_DPAA_FMAN 557 #define CONFIG_FMAN_ENET 558 #define CONFIG_PHYLIB_10G 559 #define CONFIG_PHY_VITESSE 560 #define CONFIG_PHY_TERANETICS 561 #endif 562 563 #ifdef CONFIG_PCI 564 #define CONFIG_PCI_INDIRECT_BRIDGE 565 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 566 #define CONFIG_E1000 567 568 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 569 #define CONFIG_DOS_PARTITION 570 #endif /* CONFIG_PCI */ 571 572 /* SATA */ 573 #define CONFIG_FSL_SATA_V2 574 575 #ifdef CONFIG_FSL_SATA_V2 576 #define CONFIG_FSL_SATA 577 #define CONFIG_LIBATA 578 579 #define CONFIG_SYS_SATA_MAX_DEVICE 2 580 #define CONFIG_SATA1 581 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 582 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 583 #define CONFIG_SATA2 584 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 585 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 586 587 #define CONFIG_LBA48 588 #define CONFIG_CMD_SATA 589 #define CONFIG_DOS_PARTITION 590 #define CONFIG_CMD_EXT2 591 #endif 592 593 #ifdef CONFIG_FMAN_ENET 594 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 595 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 596 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 597 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 598 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 599 600 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 601 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 602 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 603 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 604 605 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 606 607 #define CONFIG_SYS_TBIPA_VALUE 8 608 #define CONFIG_MII /* MII PHY management */ 609 #define CONFIG_ETHPRIME "FM1@DTSEC1" 610 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 611 #endif 612 613 /* 614 * Environment 615 */ 616 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 617 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 618 619 /* 620 * Command line configuration. 621 */ 622 #include <config_cmd_default.h> 623 624 #define CONFIG_CMD_DHCP 625 #define CONFIG_CMD_ELF 626 #define CONFIG_CMD_ERRATA 627 #define CONFIG_CMD_GREPENV 628 #define CONFIG_CMD_IRQ 629 #define CONFIG_CMD_I2C 630 #define CONFIG_CMD_MII 631 #define CONFIG_CMD_PING 632 #define CONFIG_CMD_SETEXPR 633 634 #ifdef CONFIG_PCI 635 #define CONFIG_CMD_PCI 636 #define CONFIG_CMD_NET 637 #endif 638 639 /* 640 * USB 641 */ 642 #define CONFIG_HAS_FSL_DR_USB 643 #define CONFIG_HAS_FSL_MPH_USB 644 645 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 646 #define CONFIG_CMD_USB 647 #define CONFIG_USB_STORAGE 648 #define CONFIG_USB_EHCI 649 #define CONFIG_USB_EHCI_FSL 650 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 651 #endif 652 653 #define CONFIG_CMD_EXT2 654 655 #define CONFIG_MMC 656 657 #ifdef CONFIG_MMC 658 #define CONFIG_FSL_ESDHC 659 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 660 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 661 #define CONFIG_CMD_MMC 662 #define CONFIG_GENERIC_MMC 663 #define CONFIG_CMD_EXT2 664 #define CONFIG_CMD_FAT 665 #define CONFIG_DOS_PARTITION 666 #endif 667 668 /* Hash command with SHA acceleration supported in hardware */ 669 #ifdef CONFIG_FSL_CAAM 670 #define CONFIG_CMD_HASH 671 #define CONFIG_SHA_HW_ACCEL 672 #endif 673 674 /* 675 * Miscellaneous configurable options 676 */ 677 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 678 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 679 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 680 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 681 #ifdef CONFIG_CMD_KGDB 682 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 683 #else 684 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 685 #endif 686 /* Print Buffer Size */ 687 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 688 sizeof(CONFIG_SYS_PROMPT)+16) 689 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 690 /* Boot Argument Buffer Size */ 691 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 692 693 /* 694 * For booting Linux, the board info and command line data 695 * have to be in the first 64 MB of memory, since this is 696 * the maximum mapped by the Linux kernel during initialization. 697 */ 698 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 699 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 700 701 #ifdef CONFIG_CMD_KGDB 702 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 703 #endif 704 705 /* 706 * Environment Configuration 707 */ 708 #define CONFIG_ROOTPATH "/opt/nfsroot" 709 #define CONFIG_BOOTFILE "uImage" 710 #define CONFIG_UBOOTPATH u-boot.bin 711 712 /* default location for tftp and bootm */ 713 #define CONFIG_LOADADDR 1000000 714 715 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 716 717 #define CONFIG_BAUDRATE 115200 718 719 #define __USB_PHY_TYPE utmi 720 721 #define CONFIG_EXTRA_ENV_SETTINGS \ 722 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 723 "bank_intlv=cs0_cs1\0" \ 724 "netdev=eth0\0" \ 725 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 726 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 727 "tftpflash=tftpboot $loadaddr $uboot && " \ 728 "protect off $ubootaddr +$filesize && " \ 729 "erase $ubootaddr +$filesize && " \ 730 "cp.b $loadaddr $ubootaddr $filesize && " \ 731 "protect on $ubootaddr +$filesize && " \ 732 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 733 "consoledev=ttyS0\0" \ 734 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 735 "usb_dr_mode=host\0" \ 736 "ramdiskaddr=2000000\0" \ 737 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 738 "fdtaddr=c00000\0" \ 739 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 740 "bdev=sda3\0" 741 742 #define CONFIG_HDBOOT \ 743 "setenv bootargs root=/dev/$bdev rw " \ 744 "console=$consoledev,$baudrate $othbootargs;" \ 745 "tftp $loadaddr $bootfile;" \ 746 "tftp $fdtaddr $fdtfile;" \ 747 "bootm $loadaddr - $fdtaddr" 748 749 #define CONFIG_NFSBOOTCOMMAND \ 750 "setenv bootargs root=/dev/nfs rw " \ 751 "nfsroot=$serverip:$rootpath " \ 752 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 753 "console=$consoledev,$baudrate $othbootargs;" \ 754 "tftp $loadaddr $bootfile;" \ 755 "tftp $fdtaddr $fdtfile;" \ 756 "bootm $loadaddr - $fdtaddr" 757 758 #define CONFIG_RAMBOOTCOMMAND \ 759 "setenv bootargs root=/dev/ram rw " \ 760 "console=$consoledev,$baudrate $othbootargs;" \ 761 "tftp $ramdiskaddr $ramdiskfile;" \ 762 "tftp $loadaddr $bootfile;" \ 763 "tftp $fdtaddr $fdtfile;" \ 764 "bootm $loadaddr $ramdiskaddr $fdtaddr" 765 766 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 767 768 #include <asm/fsl_secure_boot.h> 769 770 #ifdef CONFIG_SECURE_BOOT 771 #define CONFIG_CMD_BLOB 772 #endif 773 774 #endif /* __CONFIG_H */ 775