1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #ifdef CONFIG_RAMBOOT_PBL 15 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 16 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 19 #endif 20 21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 22 /* Set 1M boot space */ 23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 25 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 27 #define CONFIG_SYS_NO_FLASH 28 #endif 29 30 /* High Level Configuration Options */ 31 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 32 #define CONFIG_MP /* support multiple processors */ 33 34 #ifndef CONFIG_SYS_TEXT_BASE 35 #define CONFIG_SYS_TEXT_BASE 0xeff40000 36 #endif 37 38 #ifndef CONFIG_RESET_VECTOR_ADDRESS 39 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 40 #endif 41 42 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 43 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 44 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 45 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 46 #define CONFIG_PCIE1 /* PCIE controller 1 */ 47 #define CONFIG_PCIE2 /* PCIE controller 2 */ 48 #define CONFIG_PCIE3 /* PCIE controller 3 */ 49 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 50 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 51 52 #define CONFIG_SYS_SRIO 53 #define CONFIG_SRIO1 /* SRIO port 1 */ 54 #define CONFIG_SRIO2 /* SRIO port 2 */ 55 #define CONFIG_SRIO_PCIE_BOOT_MASTER 56 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 57 58 #define CONFIG_ENV_OVERWRITE 59 60 #ifdef CONFIG_SYS_NO_FLASH 61 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 62 #define CONFIG_ENV_IS_NOWHERE 63 #endif 64 #else 65 #define CONFIG_FLASH_CFI_DRIVER 66 #define CONFIG_SYS_FLASH_CFI 67 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 68 #endif 69 70 #if defined(CONFIG_SPIFLASH) 71 #define CONFIG_SYS_EXTRA_ENV_RELOC 72 #define CONFIG_ENV_IS_IN_SPI_FLASH 73 #define CONFIG_ENV_SPI_BUS 0 74 #define CONFIG_ENV_SPI_CS 0 75 #define CONFIG_ENV_SPI_MAX_HZ 10000000 76 #define CONFIG_ENV_SPI_MODE 0 77 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 78 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 79 #define CONFIG_ENV_SECT_SIZE 0x10000 80 #elif defined(CONFIG_SDCARD) 81 #define CONFIG_SYS_EXTRA_ENV_RELOC 82 #define CONFIG_ENV_IS_IN_MMC 83 #define CONFIG_FSL_FIXED_MMC_LOCATION 84 #define CONFIG_SYS_MMC_ENV_DEV 0 85 #define CONFIG_ENV_SIZE 0x2000 86 #define CONFIG_ENV_OFFSET (512 * 1658) 87 #elif defined(CONFIG_NAND) 88 #define CONFIG_SYS_EXTRA_ENV_RELOC 89 #define CONFIG_ENV_IS_IN_NAND 90 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 91 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 92 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 93 #define CONFIG_ENV_IS_IN_REMOTE 94 #define CONFIG_ENV_ADDR 0xffe20000 95 #define CONFIG_ENV_SIZE 0x2000 96 #elif defined(CONFIG_ENV_IS_NOWHERE) 97 #define CONFIG_ENV_SIZE 0x2000 98 #else 99 #define CONFIG_ENV_IS_IN_FLASH 100 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 101 - CONFIG_ENV_SECT_SIZE) 102 #define CONFIG_ENV_SIZE 0x2000 103 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 104 #endif 105 106 #ifndef __ASSEMBLY__ 107 unsigned long get_board_sys_clk(unsigned long dummy); 108 #endif 109 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 110 111 /* 112 * These can be toggled for performance analysis, otherwise use default. 113 */ 114 #define CONFIG_SYS_CACHE_STASHING 115 #define CONFIG_BACKSIDE_L2_CACHE 116 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 117 #define CONFIG_BTB /* toggle branch predition */ 118 119 #define CONFIG_ENABLE_36BIT_PHYS 120 121 #ifdef CONFIG_PHYS_64BIT 122 #define CONFIG_ADDR_MAP 123 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 124 #endif 125 126 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 127 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 128 #define CONFIG_SYS_MEMTEST_END 0x00400000 129 #define CONFIG_SYS_ALT_MEMTEST 130 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 131 132 /* 133 * Config the L3 Cache as L3 SRAM 134 */ 135 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 136 #ifdef CONFIG_PHYS_64BIT 137 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 138 CONFIG_RAMBOOT_TEXT_BASE) 139 #else 140 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 141 #endif 142 #define CONFIG_SYS_L3_SIZE (1024 << 10) 143 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 144 145 #ifdef CONFIG_PHYS_64BIT 146 #define CONFIG_SYS_DCSRBAR 0xf0000000 147 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 148 #endif 149 150 /* EEPROM */ 151 #define CONFIG_ID_EEPROM 152 #define CONFIG_SYS_I2C_EEPROM_NXID 153 #define CONFIG_SYS_EEPROM_BUS_NUM 0 154 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 155 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 156 157 /* 158 * DDR Setup 159 */ 160 #define CONFIG_VERY_BIG_RAM 161 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 162 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 163 164 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 165 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 166 167 #define CONFIG_DDR_SPD 168 169 #define CONFIG_SYS_SPD_BUS_NUM 0 170 #define SPD_EEPROM_ADDRESS 0x52 171 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 172 173 /* 174 * Local Bus Definitions 175 */ 176 177 /* Set the local bus clock 1/8 of platform clock */ 178 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 179 180 /* 181 * This board doesn't have a promjet connector. 182 * However, it uses commone corenet board LAW and TLB. 183 * It is necessary to use the same start address with proper offset. 184 */ 185 #define CONFIG_SYS_FLASH_BASE 0xe0000000 186 #ifdef CONFIG_PHYS_64BIT 187 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 188 #else 189 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 190 #endif 191 192 #define CONFIG_SYS_FLASH_BR_PRELIM \ 193 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 194 BR_PS_16 | BR_V) 195 #define CONFIG_SYS_FLASH_OR_PRELIM \ 196 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 197 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 198 199 #define CONFIG_FSL_CPLD 200 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 201 #ifdef CONFIG_PHYS_64BIT 202 #define CPLD_BASE_PHYS 0xfffdf0000ull 203 #else 204 #define CPLD_BASE_PHYS CPLD_BASE 205 #endif 206 207 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 208 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 209 210 #define PIXIS_LBMAP_SWITCH 7 211 #define PIXIS_LBMAP_MASK 0xf0 212 #define PIXIS_LBMAP_SHIFT 4 213 #define PIXIS_LBMAP_ALTBANK 0x40 214 215 #define CONFIG_SYS_FLASH_QUIET_TEST 216 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 217 218 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 219 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 220 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 221 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 222 223 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 224 225 #if defined(CONFIG_RAMBOOT_PBL) 226 #define CONFIG_SYS_RAMBOOT 227 #endif 228 229 #define CONFIG_NAND_FSL_ELBC 230 /* Nand Flash */ 231 #ifdef CONFIG_NAND_FSL_ELBC 232 #define CONFIG_SYS_NAND_BASE 0xffa00000 233 #ifdef CONFIG_PHYS_64BIT 234 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 235 #else 236 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 237 #endif 238 239 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 240 #define CONFIG_SYS_MAX_NAND_DEVICE 1 241 #define CONFIG_CMD_NAND 242 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 243 244 /* NAND flash config */ 245 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 246 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 247 | BR_PS_8 /* Port Size = 8 bit */ \ 248 | BR_MS_FCM /* MSEL = FCM */ \ 249 | BR_V) /* valid */ 250 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 251 | OR_FCM_PGS /* Large Page*/ \ 252 | OR_FCM_CSCT \ 253 | OR_FCM_CST \ 254 | OR_FCM_CHT \ 255 | OR_FCM_SCY_1 \ 256 | OR_FCM_TRLX \ 257 | OR_FCM_EHTR) 258 259 #ifdef CONFIG_NAND 260 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 261 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 262 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 263 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 264 #else 265 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 266 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 267 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 268 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 269 #endif 270 #else 271 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 272 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 273 #endif /* CONFIG_NAND_FSL_ELBC */ 274 275 #define CONFIG_SYS_FLASH_EMPTY_INFO 276 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 277 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 278 279 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 280 #define CONFIG_MISC_INIT_R 281 282 #define CONFIG_HWCONFIG 283 284 /* define to use L1 as initial stack */ 285 #define CONFIG_L1_INIT_RAM 286 #define CONFIG_SYS_INIT_RAM_LOCK 287 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 288 #ifdef CONFIG_PHYS_64BIT 289 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 290 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 291 /* The assembler doesn't like typecast */ 292 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 293 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 294 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 295 #else 296 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 297 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 298 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 299 #endif 300 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 301 302 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 303 GENERATED_GBL_DATA_SIZE) 304 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 305 306 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 307 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 308 309 /* Serial Port - controlled on board with jumper J8 310 * open - index 2 311 * shorted - index 1 312 */ 313 #define CONFIG_CONS_INDEX 1 314 #define CONFIG_SYS_NS16550_SERIAL 315 #define CONFIG_SYS_NS16550_REG_SIZE 1 316 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 317 318 #define CONFIG_SYS_BAUDRATE_TABLE \ 319 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 320 321 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 322 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 323 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 324 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 325 326 /* I2C */ 327 #define CONFIG_SYS_I2C 328 #define CONFIG_SYS_I2C_FSL 329 #define CONFIG_SYS_FSL_I2C_SPEED 400000 330 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 331 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 332 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 333 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 334 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 335 336 /* 337 * RapidIO 338 */ 339 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 340 #ifdef CONFIG_PHYS_64BIT 341 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 342 #else 343 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 344 #endif 345 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 346 347 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 348 #ifdef CONFIG_PHYS_64BIT 349 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 350 #else 351 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 352 #endif 353 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 354 355 /* 356 * for slave u-boot IMAGE instored in master memory space, 357 * PHYS must be aligned based on the SIZE 358 */ 359 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 360 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 361 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 362 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 363 /* 364 * for slave UCODE and ENV instored in master memory space, 365 * PHYS must be aligned based on the SIZE 366 */ 367 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 368 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 369 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 370 371 /* slave core release by master*/ 372 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 373 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 374 375 /* 376 * SRIO_PCIE_BOOT - SLAVE 377 */ 378 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 379 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 380 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 381 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 382 #endif 383 384 /* 385 * eSPI - Enhanced SPI 386 */ 387 #define CONFIG_SF_DEFAULT_SPEED 10000000 388 #define CONFIG_SF_DEFAULT_MODE 0 389 390 /* 391 * General PCI 392 * Memory space is mapped 1-1, but I/O space must start from 0. 393 */ 394 395 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 396 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 397 #ifdef CONFIG_PHYS_64BIT 398 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 399 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 400 #else 401 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 402 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 403 #endif 404 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 405 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 406 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 407 #ifdef CONFIG_PHYS_64BIT 408 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 409 #else 410 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 411 #endif 412 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 413 414 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 415 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 416 #ifdef CONFIG_PHYS_64BIT 417 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 418 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 419 #else 420 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 421 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 422 #endif 423 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 424 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 425 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 426 #ifdef CONFIG_PHYS_64BIT 427 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 428 #else 429 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 430 #endif 431 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 432 433 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 434 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 435 #ifdef CONFIG_PHYS_64BIT 436 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 437 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 438 #else 439 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 440 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 441 #endif 442 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 443 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 444 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 445 #ifdef CONFIG_PHYS_64BIT 446 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 447 #else 448 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 449 #endif 450 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 451 452 /* Qman/Bman */ 453 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 454 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 455 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 456 #ifdef CONFIG_PHYS_64BIT 457 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 458 #else 459 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 460 #endif 461 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 462 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 463 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 464 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 465 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 466 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 467 CONFIG_SYS_BMAN_CENA_SIZE) 468 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 469 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 470 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 471 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 472 #ifdef CONFIG_PHYS_64BIT 473 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 474 #else 475 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 476 #endif 477 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 478 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 479 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 480 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 481 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 482 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 483 CONFIG_SYS_QMAN_CENA_SIZE) 484 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 485 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 486 487 #define CONFIG_SYS_DPAA_FMAN 488 #define CONFIG_SYS_DPAA_PME 489 /* Default address of microcode for the Linux Fman driver */ 490 #if defined(CONFIG_SPIFLASH) 491 /* 492 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 493 * env, so we got 0x110000. 494 */ 495 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 496 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 497 #elif defined(CONFIG_SDCARD) 498 /* 499 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 500 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 501 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 502 */ 503 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 504 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 505 #elif defined(CONFIG_NAND) 506 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 507 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 508 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 509 /* 510 * Slave has no ucode locally, it can fetch this from remote. When implementing 511 * in two corenet boards, slave's ucode could be stored in master's memory 512 * space, the address can be mapped from slave TLB->slave LAW-> 513 * slave SRIO or PCIE outbound window->master inbound window-> 514 * master LAW->the ucode address in master's memory space. 515 */ 516 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 517 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 518 #else 519 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 520 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 521 #endif 522 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 523 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 524 525 #ifdef CONFIG_SYS_DPAA_FMAN 526 #define CONFIG_FMAN_ENET 527 #define CONFIG_PHYLIB_10G 528 #define CONFIG_PHY_VITESSE 529 #define CONFIG_PHY_TERANETICS 530 #endif 531 532 #ifdef CONFIG_PCI 533 #define CONFIG_PCI_INDIRECT_BRIDGE 534 535 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 536 #define CONFIG_DOS_PARTITION 537 #endif /* CONFIG_PCI */ 538 539 /* SATA */ 540 #define CONFIG_FSL_SATA_V2 541 542 #ifdef CONFIG_FSL_SATA_V2 543 #define CONFIG_FSL_SATA 544 #define CONFIG_LIBATA 545 546 #define CONFIG_SYS_SATA_MAX_DEVICE 2 547 #define CONFIG_SATA1 548 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 549 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 550 #define CONFIG_SATA2 551 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 552 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 553 554 #define CONFIG_LBA48 555 #define CONFIG_CMD_SATA 556 #define CONFIG_DOS_PARTITION 557 #endif 558 559 #ifdef CONFIG_FMAN_ENET 560 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 561 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 562 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 563 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 564 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 565 566 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 567 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 568 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 569 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 570 571 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 572 573 #define CONFIG_SYS_TBIPA_VALUE 8 574 #define CONFIG_MII /* MII PHY management */ 575 #define CONFIG_ETHPRIME "FM1@DTSEC1" 576 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 577 #endif 578 579 /* 580 * Environment 581 */ 582 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 583 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 584 585 /* 586 * Command line configuration. 587 */ 588 #define CONFIG_CMD_ERRATA 589 #define CONFIG_CMD_IRQ 590 591 #ifdef CONFIG_PCI 592 #define CONFIG_CMD_PCI 593 #endif 594 595 /* 596 * USB 597 */ 598 #define CONFIG_HAS_FSL_DR_USB 599 #define CONFIG_HAS_FSL_MPH_USB 600 601 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 602 #define CONFIG_USB_EHCI 603 #define CONFIG_USB_EHCI_FSL 604 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 605 #endif 606 607 #ifdef CONFIG_MMC 608 #define CONFIG_FSL_ESDHC 609 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 610 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 611 #define CONFIG_GENERIC_MMC 612 #define CONFIG_DOS_PARTITION 613 #endif 614 615 /* Hash command with SHA acceleration supported in hardware */ 616 #ifdef CONFIG_FSL_CAAM 617 #define CONFIG_CMD_HASH 618 #define CONFIG_SHA_HW_ACCEL 619 #endif 620 621 /* 622 * Miscellaneous configurable options 623 */ 624 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 625 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 626 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 627 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 628 #ifdef CONFIG_CMD_KGDB 629 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 630 #else 631 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 632 #endif 633 /* Print Buffer Size */ 634 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 635 sizeof(CONFIG_SYS_PROMPT)+16) 636 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 637 /* Boot Argument Buffer Size */ 638 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 639 640 /* 641 * For booting Linux, the board info and command line data 642 * have to be in the first 64 MB of memory, since this is 643 * the maximum mapped by the Linux kernel during initialization. 644 */ 645 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 646 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 647 648 #ifdef CONFIG_CMD_KGDB 649 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 650 #endif 651 652 /* 653 * Environment Configuration 654 */ 655 #define CONFIG_ROOTPATH "/opt/nfsroot" 656 #define CONFIG_BOOTFILE "uImage" 657 #define CONFIG_UBOOTPATH u-boot.bin 658 659 /* default location for tftp and bootm */ 660 #define CONFIG_LOADADDR 1000000 661 662 663 #define CONFIG_BAUDRATE 115200 664 665 #define __USB_PHY_TYPE utmi 666 667 #define CONFIG_EXTRA_ENV_SETTINGS \ 668 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 669 "bank_intlv=cs0_cs1\0" \ 670 "netdev=eth0\0" \ 671 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 672 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 673 "tftpflash=tftpboot $loadaddr $uboot && " \ 674 "protect off $ubootaddr +$filesize && " \ 675 "erase $ubootaddr +$filesize && " \ 676 "cp.b $loadaddr $ubootaddr $filesize && " \ 677 "protect on $ubootaddr +$filesize && " \ 678 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 679 "consoledev=ttyS0\0" \ 680 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 681 "usb_dr_mode=host\0" \ 682 "ramdiskaddr=2000000\0" \ 683 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 684 "fdtaddr=1e00000\0" \ 685 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 686 "bdev=sda3\0" 687 688 #define CONFIG_HDBOOT \ 689 "setenv bootargs root=/dev/$bdev rw " \ 690 "console=$consoledev,$baudrate $othbootargs;" \ 691 "tftp $loadaddr $bootfile;" \ 692 "tftp $fdtaddr $fdtfile;" \ 693 "bootm $loadaddr - $fdtaddr" 694 695 #define CONFIG_NFSBOOTCOMMAND \ 696 "setenv bootargs root=/dev/nfs rw " \ 697 "nfsroot=$serverip:$rootpath " \ 698 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 699 "console=$consoledev,$baudrate $othbootargs;" \ 700 "tftp $loadaddr $bootfile;" \ 701 "tftp $fdtaddr $fdtfile;" \ 702 "bootm $loadaddr - $fdtaddr" 703 704 #define CONFIG_RAMBOOTCOMMAND \ 705 "setenv bootargs root=/dev/ram rw " \ 706 "console=$consoledev,$baudrate $othbootargs;" \ 707 "tftp $ramdiskaddr $ramdiskfile;" \ 708 "tftp $loadaddr $bootfile;" \ 709 "tftp $fdtaddr $fdtfile;" \ 710 "bootm $loadaddr $ramdiskaddr $fdtaddr" 711 712 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 713 714 #include <asm/fsl_secure_boot.h> 715 716 #endif /* __CONFIG_H */ 717