1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_P2041RDB 15 #define CONFIG_PHYS_64BIT 16 #define CONFIG_DISPLAY_BOARDINFO 17 #define CONFIG_PPC_P2041 18 19 #ifdef CONFIG_RAMBOOT_PBL 20 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 21 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 22 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 23 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 24 #endif 25 26 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 27 /* Set 1M boot space */ 28 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 29 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 30 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 31 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 32 #define CONFIG_SYS_NO_FLASH 33 #endif 34 35 /* High Level Configuration Options */ 36 #define CONFIG_BOOKE 37 #define CONFIG_E500 /* BOOKE e500 family */ 38 #define CONFIG_E500MC /* BOOKE e500mc family */ 39 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 40 #define CONFIG_MP /* support multiple processors */ 41 42 #ifndef CONFIG_SYS_TEXT_BASE 43 #define CONFIG_SYS_TEXT_BASE 0xeff40000 44 #endif 45 46 #ifndef CONFIG_RESET_VECTOR_ADDRESS 47 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 48 #endif 49 50 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 51 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 52 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 53 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 54 #define CONFIG_PCI /* Enable PCI/PCIE */ 55 #define CONFIG_PCIE1 /* PCIE controler 1 */ 56 #define CONFIG_PCIE2 /* PCIE controler 2 */ 57 #define CONFIG_PCIE3 /* PCIE controler 3 */ 58 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 59 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 60 61 #define CONFIG_SYS_SRIO 62 #define CONFIG_SRIO1 /* SRIO port 1 */ 63 #define CONFIG_SRIO2 /* SRIO port 2 */ 64 #define CONFIG_SRIO_PCIE_BOOT_MASTER 65 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 66 67 #define CONFIG_FSL_LAW /* Use common FSL init code */ 68 69 #define CONFIG_ENV_OVERWRITE 70 71 #ifdef CONFIG_SYS_NO_FLASH 72 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 73 #define CONFIG_ENV_IS_NOWHERE 74 #endif 75 #else 76 #define CONFIG_FLASH_CFI_DRIVER 77 #define CONFIG_SYS_FLASH_CFI 78 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 79 #endif 80 81 #if defined(CONFIG_SPIFLASH) 82 #define CONFIG_SYS_EXTRA_ENV_RELOC 83 #define CONFIG_ENV_IS_IN_SPI_FLASH 84 #define CONFIG_ENV_SPI_BUS 0 85 #define CONFIG_ENV_SPI_CS 0 86 #define CONFIG_ENV_SPI_MAX_HZ 10000000 87 #define CONFIG_ENV_SPI_MODE 0 88 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 89 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 90 #define CONFIG_ENV_SECT_SIZE 0x10000 91 #elif defined(CONFIG_SDCARD) 92 #define CONFIG_SYS_EXTRA_ENV_RELOC 93 #define CONFIG_ENV_IS_IN_MMC 94 #define CONFIG_FSL_FIXED_MMC_LOCATION 95 #define CONFIG_SYS_MMC_ENV_DEV 0 96 #define CONFIG_ENV_SIZE 0x2000 97 #define CONFIG_ENV_OFFSET (512 * 1658) 98 #elif defined(CONFIG_NAND) 99 #define CONFIG_SYS_EXTRA_ENV_RELOC 100 #define CONFIG_ENV_IS_IN_NAND 101 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 102 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 103 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 104 #define CONFIG_ENV_IS_IN_REMOTE 105 #define CONFIG_ENV_ADDR 0xffe20000 106 #define CONFIG_ENV_SIZE 0x2000 107 #elif defined(CONFIG_ENV_IS_NOWHERE) 108 #define CONFIG_ENV_SIZE 0x2000 109 #else 110 #define CONFIG_ENV_IS_IN_FLASH 111 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 112 - CONFIG_ENV_SECT_SIZE) 113 #define CONFIG_ENV_SIZE 0x2000 114 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 115 #endif 116 117 #ifndef __ASSEMBLY__ 118 unsigned long get_board_sys_clk(unsigned long dummy); 119 #endif 120 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 121 122 /* 123 * These can be toggled for performance analysis, otherwise use default. 124 */ 125 #define CONFIG_SYS_CACHE_STASHING 126 #define CONFIG_BACKSIDE_L2_CACHE 127 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 128 #define CONFIG_BTB /* toggle branch predition */ 129 130 #define CONFIG_ENABLE_36BIT_PHYS 131 132 #ifdef CONFIG_PHYS_64BIT 133 #define CONFIG_ADDR_MAP 134 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 135 #endif 136 137 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 138 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 139 #define CONFIG_SYS_MEMTEST_END 0x00400000 140 #define CONFIG_SYS_ALT_MEMTEST 141 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 142 143 /* 144 * Config the L3 Cache as L3 SRAM 145 */ 146 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 147 #ifdef CONFIG_PHYS_64BIT 148 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 149 CONFIG_RAMBOOT_TEXT_BASE) 150 #else 151 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 152 #endif 153 #define CONFIG_SYS_L3_SIZE (1024 << 10) 154 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 155 156 #ifdef CONFIG_PHYS_64BIT 157 #define CONFIG_SYS_DCSRBAR 0xf0000000 158 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 159 #endif 160 161 /* EEPROM */ 162 #define CONFIG_ID_EEPROM 163 #define CONFIG_SYS_I2C_EEPROM_NXID 164 #define CONFIG_SYS_EEPROM_BUS_NUM 0 165 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 166 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 167 168 /* 169 * DDR Setup 170 */ 171 #define CONFIG_VERY_BIG_RAM 172 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 173 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 174 175 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 176 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 177 178 #define CONFIG_DDR_SPD 179 #define CONFIG_SYS_FSL_DDR3 180 181 #define CONFIG_SYS_SPD_BUS_NUM 0 182 #define SPD_EEPROM_ADDRESS 0x52 183 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 184 185 /* 186 * Local Bus Definitions 187 */ 188 189 /* Set the local bus clock 1/8 of platform clock */ 190 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 191 192 /* 193 * This board doesn't have a promjet connector. 194 * However, it uses commone corenet board LAW and TLB. 195 * It is necessary to use the same start address with proper offset. 196 */ 197 #define CONFIG_SYS_FLASH_BASE 0xe0000000 198 #ifdef CONFIG_PHYS_64BIT 199 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 200 #else 201 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 202 #endif 203 204 #define CONFIG_SYS_FLASH_BR_PRELIM \ 205 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 206 BR_PS_16 | BR_V) 207 #define CONFIG_SYS_FLASH_OR_PRELIM \ 208 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 209 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 210 211 #define CONFIG_FSL_CPLD 212 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 213 #ifdef CONFIG_PHYS_64BIT 214 #define CPLD_BASE_PHYS 0xfffdf0000ull 215 #else 216 #define CPLD_BASE_PHYS CPLD_BASE 217 #endif 218 219 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 220 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 221 222 #define PIXIS_LBMAP_SWITCH 7 223 #define PIXIS_LBMAP_MASK 0xf0 224 #define PIXIS_LBMAP_SHIFT 4 225 #define PIXIS_LBMAP_ALTBANK 0x40 226 227 #define CONFIG_SYS_FLASH_QUIET_TEST 228 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 229 230 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 231 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 232 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 233 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 234 235 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 236 237 #if defined(CONFIG_RAMBOOT_PBL) 238 #define CONFIG_SYS_RAMBOOT 239 #endif 240 241 #define CONFIG_NAND_FSL_ELBC 242 /* Nand Flash */ 243 #ifdef CONFIG_NAND_FSL_ELBC 244 #define CONFIG_SYS_NAND_BASE 0xffa00000 245 #ifdef CONFIG_PHYS_64BIT 246 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 247 #else 248 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 249 #endif 250 251 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 252 #define CONFIG_SYS_MAX_NAND_DEVICE 1 253 #define CONFIG_CMD_NAND 254 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 255 256 /* NAND flash config */ 257 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 258 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 259 | BR_PS_8 /* Port Size = 8 bit */ \ 260 | BR_MS_FCM /* MSEL = FCM */ \ 261 | BR_V) /* valid */ 262 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 263 | OR_FCM_PGS /* Large Page*/ \ 264 | OR_FCM_CSCT \ 265 | OR_FCM_CST \ 266 | OR_FCM_CHT \ 267 | OR_FCM_SCY_1 \ 268 | OR_FCM_TRLX \ 269 | OR_FCM_EHTR) 270 271 #ifdef CONFIG_NAND 272 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 273 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 274 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 275 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 276 #else 277 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 278 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 279 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 280 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 281 #endif 282 #else 283 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 284 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 285 #endif /* CONFIG_NAND_FSL_ELBC */ 286 287 #define CONFIG_SYS_FLASH_EMPTY_INFO 288 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 289 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 290 291 #define CONFIG_BOARD_EARLY_INIT_F 292 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 293 #define CONFIG_MISC_INIT_R 294 295 #define CONFIG_HWCONFIG 296 297 /* define to use L1 as initial stack */ 298 #define CONFIG_L1_INIT_RAM 299 #define CONFIG_SYS_INIT_RAM_LOCK 300 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 301 #ifdef CONFIG_PHYS_64BIT 302 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 303 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 304 /* The assembler doesn't like typecast */ 305 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 306 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 307 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 308 #else 309 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 310 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 311 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 312 #endif 313 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 314 315 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 316 GENERATED_GBL_DATA_SIZE) 317 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 318 319 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 320 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 321 322 /* Serial Port - controlled on board with jumper J8 323 * open - index 2 324 * shorted - index 1 325 */ 326 #define CONFIG_CONS_INDEX 1 327 #define CONFIG_SYS_NS16550 328 #define CONFIG_SYS_NS16550_SERIAL 329 #define CONFIG_SYS_NS16550_REG_SIZE 1 330 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 331 332 #define CONFIG_SYS_BAUDRATE_TABLE \ 333 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 334 335 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 336 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 337 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 338 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 339 340 /* Use the HUSH parser */ 341 #define CONFIG_SYS_HUSH_PARSER 342 343 /* pass open firmware flat tree */ 344 #define CONFIG_OF_LIBFDT 345 #define CONFIG_OF_BOARD_SETUP 346 #define CONFIG_OF_STDOUT_VIA_ALIAS 347 348 /* new uImage format support */ 349 #define CONFIG_FIT 350 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 351 352 /* I2C */ 353 #define CONFIG_SYS_I2C 354 #define CONFIG_SYS_I2C_FSL 355 #define CONFIG_SYS_FSL_I2C_SPEED 400000 356 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 357 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 358 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 359 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 360 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 361 362 /* 363 * RapidIO 364 */ 365 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 366 #ifdef CONFIG_PHYS_64BIT 367 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 368 #else 369 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 370 #endif 371 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 372 373 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 374 #ifdef CONFIG_PHYS_64BIT 375 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 376 #else 377 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 378 #endif 379 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 380 381 /* 382 * for slave u-boot IMAGE instored in master memory space, 383 * PHYS must be aligned based on the SIZE 384 */ 385 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 386 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 387 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 388 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 389 /* 390 * for slave UCODE and ENV instored in master memory space, 391 * PHYS must be aligned based on the SIZE 392 */ 393 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 394 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 395 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 396 397 /* slave core release by master*/ 398 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 399 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 400 401 /* 402 * SRIO_PCIE_BOOT - SLAVE 403 */ 404 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 405 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 406 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 407 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 408 #endif 409 410 /* 411 * eSPI - Enhanced SPI 412 */ 413 #define CONFIG_FSL_ESPI 414 #define CONFIG_SPI_FLASH_SPANSION 415 #define CONFIG_CMD_SF 416 #define CONFIG_SF_DEFAULT_SPEED 10000000 417 #define CONFIG_SF_DEFAULT_MODE 0 418 419 /* 420 * General PCI 421 * Memory space is mapped 1-1, but I/O space must start from 0. 422 */ 423 424 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 425 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 426 #ifdef CONFIG_PHYS_64BIT 427 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 428 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 429 #else 430 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 431 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 432 #endif 433 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 434 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 435 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 436 #ifdef CONFIG_PHYS_64BIT 437 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 438 #else 439 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 440 #endif 441 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 442 443 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 444 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 445 #ifdef CONFIG_PHYS_64BIT 446 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 447 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 448 #else 449 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 450 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 451 #endif 452 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 453 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 454 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 455 #ifdef CONFIG_PHYS_64BIT 456 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 457 #else 458 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 459 #endif 460 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 461 462 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 463 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 464 #ifdef CONFIG_PHYS_64BIT 465 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 466 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 467 #else 468 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 469 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 470 #endif 471 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 472 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 473 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 474 #ifdef CONFIG_PHYS_64BIT 475 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 476 #else 477 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 478 #endif 479 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 480 481 /* Qman/Bman */ 482 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 483 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 484 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 485 #ifdef CONFIG_PHYS_64BIT 486 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 487 #else 488 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 489 #endif 490 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 491 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 492 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 493 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 494 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 495 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 496 CONFIG_SYS_BMAN_CENA_SIZE) 497 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 498 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 499 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 500 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 501 #ifdef CONFIG_PHYS_64BIT 502 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 503 #else 504 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 505 #endif 506 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 507 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 508 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 509 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 510 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 511 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 512 CONFIG_SYS_QMAN_CENA_SIZE) 513 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 514 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 515 516 #define CONFIG_SYS_DPAA_FMAN 517 #define CONFIG_SYS_DPAA_PME 518 /* Default address of microcode for the Linux Fman driver */ 519 #if defined(CONFIG_SPIFLASH) 520 /* 521 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 522 * env, so we got 0x110000. 523 */ 524 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 525 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 526 #elif defined(CONFIG_SDCARD) 527 /* 528 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 529 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 530 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 531 */ 532 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 533 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 534 #elif defined(CONFIG_NAND) 535 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 536 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 537 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 538 /* 539 * Slave has no ucode locally, it can fetch this from remote. When implementing 540 * in two corenet boards, slave's ucode could be stored in master's memory 541 * space, the address can be mapped from slave TLB->slave LAW-> 542 * slave SRIO or PCIE outbound window->master inbound window-> 543 * master LAW->the ucode address in master's memory space. 544 */ 545 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 546 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 547 #else 548 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 549 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 550 #endif 551 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 552 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 553 554 #ifdef CONFIG_SYS_DPAA_FMAN 555 #define CONFIG_FMAN_ENET 556 #define CONFIG_PHYLIB_10G 557 #define CONFIG_PHY_VITESSE 558 #define CONFIG_PHY_TERANETICS 559 #endif 560 561 #ifdef CONFIG_PCI 562 #define CONFIG_PCI_INDIRECT_BRIDGE 563 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 564 565 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 566 #define CONFIG_DOS_PARTITION 567 #endif /* CONFIG_PCI */ 568 569 /* SATA */ 570 #define CONFIG_FSL_SATA_V2 571 572 #ifdef CONFIG_FSL_SATA_V2 573 #define CONFIG_FSL_SATA 574 #define CONFIG_LIBATA 575 576 #define CONFIG_SYS_SATA_MAX_DEVICE 2 577 #define CONFIG_SATA1 578 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 579 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 580 #define CONFIG_SATA2 581 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 582 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 583 584 #define CONFIG_LBA48 585 #define CONFIG_CMD_SATA 586 #define CONFIG_DOS_PARTITION 587 #define CONFIG_CMD_EXT2 588 #endif 589 590 #ifdef CONFIG_FMAN_ENET 591 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 592 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 593 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 594 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 595 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 596 597 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 598 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 599 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 600 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 601 602 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 603 604 #define CONFIG_SYS_TBIPA_VALUE 8 605 #define CONFIG_MII /* MII PHY management */ 606 #define CONFIG_ETHPRIME "FM1@DTSEC1" 607 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 608 #endif 609 610 /* 611 * Environment 612 */ 613 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 614 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 615 616 /* 617 * Command line configuration. 618 */ 619 #define CONFIG_CMD_DHCP 620 #define CONFIG_CMD_ERRATA 621 #define CONFIG_CMD_GREPENV 622 #define CONFIG_CMD_IRQ 623 #define CONFIG_CMD_I2C 624 #define CONFIG_CMD_MII 625 #define CONFIG_CMD_PING 626 627 #ifdef CONFIG_PCI 628 #define CONFIG_CMD_PCI 629 #endif 630 631 /* 632 * USB 633 */ 634 #define CONFIG_HAS_FSL_DR_USB 635 #define CONFIG_HAS_FSL_MPH_USB 636 637 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 638 #define CONFIG_CMD_USB 639 #define CONFIG_USB_STORAGE 640 #define CONFIG_USB_EHCI 641 #define CONFIG_USB_EHCI_FSL 642 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 643 #endif 644 645 #define CONFIG_CMD_EXT2 646 647 #define CONFIG_MMC 648 649 #ifdef CONFIG_MMC 650 #define CONFIG_FSL_ESDHC 651 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 652 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 653 #define CONFIG_CMD_MMC 654 #define CONFIG_GENERIC_MMC 655 #define CONFIG_CMD_EXT2 656 #define CONFIG_CMD_FAT 657 #define CONFIG_DOS_PARTITION 658 #endif 659 660 /* Hash command with SHA acceleration supported in hardware */ 661 #ifdef CONFIG_FSL_CAAM 662 #define CONFIG_CMD_HASH 663 #define CONFIG_SHA_HW_ACCEL 664 #endif 665 666 /* 667 * Miscellaneous configurable options 668 */ 669 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 670 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 671 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 672 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 673 #ifdef CONFIG_CMD_KGDB 674 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 675 #else 676 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 677 #endif 678 /* Print Buffer Size */ 679 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 680 sizeof(CONFIG_SYS_PROMPT)+16) 681 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 682 /* Boot Argument Buffer Size */ 683 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 684 685 /* 686 * For booting Linux, the board info and command line data 687 * have to be in the first 64 MB of memory, since this is 688 * the maximum mapped by the Linux kernel during initialization. 689 */ 690 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 691 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 692 693 #ifdef CONFIG_CMD_KGDB 694 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 695 #endif 696 697 /* 698 * Environment Configuration 699 */ 700 #define CONFIG_ROOTPATH "/opt/nfsroot" 701 #define CONFIG_BOOTFILE "uImage" 702 #define CONFIG_UBOOTPATH u-boot.bin 703 704 /* default location for tftp and bootm */ 705 #define CONFIG_LOADADDR 1000000 706 707 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 708 709 #define CONFIG_BAUDRATE 115200 710 711 #define __USB_PHY_TYPE utmi 712 713 #define CONFIG_EXTRA_ENV_SETTINGS \ 714 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 715 "bank_intlv=cs0_cs1\0" \ 716 "netdev=eth0\0" \ 717 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 718 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 719 "tftpflash=tftpboot $loadaddr $uboot && " \ 720 "protect off $ubootaddr +$filesize && " \ 721 "erase $ubootaddr +$filesize && " \ 722 "cp.b $loadaddr $ubootaddr $filesize && " \ 723 "protect on $ubootaddr +$filesize && " \ 724 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 725 "consoledev=ttyS0\0" \ 726 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 727 "usb_dr_mode=host\0" \ 728 "ramdiskaddr=2000000\0" \ 729 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 730 "fdtaddr=c00000\0" \ 731 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 732 "bdev=sda3\0" 733 734 #define CONFIG_HDBOOT \ 735 "setenv bootargs root=/dev/$bdev rw " \ 736 "console=$consoledev,$baudrate $othbootargs;" \ 737 "tftp $loadaddr $bootfile;" \ 738 "tftp $fdtaddr $fdtfile;" \ 739 "bootm $loadaddr - $fdtaddr" 740 741 #define CONFIG_NFSBOOTCOMMAND \ 742 "setenv bootargs root=/dev/nfs rw " \ 743 "nfsroot=$serverip:$rootpath " \ 744 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 745 "console=$consoledev,$baudrate $othbootargs;" \ 746 "tftp $loadaddr $bootfile;" \ 747 "tftp $fdtaddr $fdtfile;" \ 748 "bootm $loadaddr - $fdtaddr" 749 750 #define CONFIG_RAMBOOTCOMMAND \ 751 "setenv bootargs root=/dev/ram rw " \ 752 "console=$consoledev,$baudrate $othbootargs;" \ 753 "tftp $ramdiskaddr $ramdiskfile;" \ 754 "tftp $loadaddr $bootfile;" \ 755 "tftp $fdtaddr $fdtfile;" \ 756 "bootm $loadaddr $ramdiskaddr $fdtaddr" 757 758 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 759 760 #include <asm/fsl_secure_boot.h> 761 762 #ifdef CONFIG_SECURE_BOOT 763 #define CONFIG_CMD_BLOB 764 #endif 765 766 #endif /* __CONFIG_H */ 767