1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_P2041RDB 15 #define CONFIG_PHYS_64BIT 16 #define CONFIG_DISPLAY_BOARDINFO 17 #define CONFIG_PPC_P2041 18 19 #ifdef CONFIG_RAMBOOT_PBL 20 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 21 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 22 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 23 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 24 #endif 25 26 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 27 /* Set 1M boot space */ 28 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 29 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 30 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 31 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 32 #define CONFIG_SYS_NO_FLASH 33 #endif 34 35 /* High Level Configuration Options */ 36 #define CONFIG_BOOKE 37 #define CONFIG_E500 /* BOOKE e500 family */ 38 #define CONFIG_E500MC /* BOOKE e500mc family */ 39 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 40 #define CONFIG_MP /* support multiple processors */ 41 42 #ifndef CONFIG_SYS_TEXT_BASE 43 #define CONFIG_SYS_TEXT_BASE 0xeff40000 44 #endif 45 46 #ifndef CONFIG_RESET_VECTOR_ADDRESS 47 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 48 #endif 49 50 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 51 #define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS 52 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 53 #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ 54 #define CONFIG_PCI /* Enable PCI/PCIE */ 55 #define CONFIG_PCIE1 /* PCIE controller 1 */ 56 #define CONFIG_PCIE2 /* PCIE controller 2 */ 57 #define CONFIG_PCIE3 /* PCIE controller 3 */ 58 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 59 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 60 61 #define CONFIG_SYS_SRIO 62 #define CONFIG_SRIO1 /* SRIO port 1 */ 63 #define CONFIG_SRIO2 /* SRIO port 2 */ 64 #define CONFIG_SRIO_PCIE_BOOT_MASTER 65 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 66 67 #define CONFIG_FSL_LAW /* Use common FSL init code */ 68 69 #define CONFIG_ENV_OVERWRITE 70 71 #ifdef CONFIG_SYS_NO_FLASH 72 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 73 #define CONFIG_ENV_IS_NOWHERE 74 #endif 75 #else 76 #define CONFIG_FLASH_CFI_DRIVER 77 #define CONFIG_SYS_FLASH_CFI 78 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 79 #endif 80 81 #if defined(CONFIG_SPIFLASH) 82 #define CONFIG_SYS_EXTRA_ENV_RELOC 83 #define CONFIG_ENV_IS_IN_SPI_FLASH 84 #define CONFIG_ENV_SPI_BUS 0 85 #define CONFIG_ENV_SPI_CS 0 86 #define CONFIG_ENV_SPI_MAX_HZ 10000000 87 #define CONFIG_ENV_SPI_MODE 0 88 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 89 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 90 #define CONFIG_ENV_SECT_SIZE 0x10000 91 #elif defined(CONFIG_SDCARD) 92 #define CONFIG_SYS_EXTRA_ENV_RELOC 93 #define CONFIG_ENV_IS_IN_MMC 94 #define CONFIG_FSL_FIXED_MMC_LOCATION 95 #define CONFIG_SYS_MMC_ENV_DEV 0 96 #define CONFIG_ENV_SIZE 0x2000 97 #define CONFIG_ENV_OFFSET (512 * 1658) 98 #elif defined(CONFIG_NAND) 99 #define CONFIG_SYS_EXTRA_ENV_RELOC 100 #define CONFIG_ENV_IS_IN_NAND 101 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 102 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 103 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 104 #define CONFIG_ENV_IS_IN_REMOTE 105 #define CONFIG_ENV_ADDR 0xffe20000 106 #define CONFIG_ENV_SIZE 0x2000 107 #elif defined(CONFIG_ENV_IS_NOWHERE) 108 #define CONFIG_ENV_SIZE 0x2000 109 #else 110 #define CONFIG_ENV_IS_IN_FLASH 111 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 112 - CONFIG_ENV_SECT_SIZE) 113 #define CONFIG_ENV_SIZE 0x2000 114 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 115 #endif 116 117 #ifndef __ASSEMBLY__ 118 unsigned long get_board_sys_clk(unsigned long dummy); 119 #endif 120 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 121 122 /* 123 * These can be toggled for performance analysis, otherwise use default. 124 */ 125 #define CONFIG_SYS_CACHE_STASHING 126 #define CONFIG_BACKSIDE_L2_CACHE 127 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 128 #define CONFIG_BTB /* toggle branch predition */ 129 130 #define CONFIG_ENABLE_36BIT_PHYS 131 132 #ifdef CONFIG_PHYS_64BIT 133 #define CONFIG_ADDR_MAP 134 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 135 #endif 136 137 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 138 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 139 #define CONFIG_SYS_MEMTEST_END 0x00400000 140 #define CONFIG_SYS_ALT_MEMTEST 141 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 142 143 /* 144 * Config the L3 Cache as L3 SRAM 145 */ 146 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 147 #ifdef CONFIG_PHYS_64BIT 148 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 149 CONFIG_RAMBOOT_TEXT_BASE) 150 #else 151 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 152 #endif 153 #define CONFIG_SYS_L3_SIZE (1024 << 10) 154 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 155 156 #ifdef CONFIG_PHYS_64BIT 157 #define CONFIG_SYS_DCSRBAR 0xf0000000 158 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 159 #endif 160 161 /* EEPROM */ 162 #define CONFIG_ID_EEPROM 163 #define CONFIG_SYS_I2C_EEPROM_NXID 164 #define CONFIG_SYS_EEPROM_BUS_NUM 0 165 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 166 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 167 168 /* 169 * DDR Setup 170 */ 171 #define CONFIG_VERY_BIG_RAM 172 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 173 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 174 175 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 176 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 177 178 #define CONFIG_DDR_SPD 179 #define CONFIG_SYS_FSL_DDR3 180 181 #define CONFIG_SYS_SPD_BUS_NUM 0 182 #define SPD_EEPROM_ADDRESS 0x52 183 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 184 185 /* 186 * Local Bus Definitions 187 */ 188 189 /* Set the local bus clock 1/8 of platform clock */ 190 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 191 192 /* 193 * This board doesn't have a promjet connector. 194 * However, it uses commone corenet board LAW and TLB. 195 * It is necessary to use the same start address with proper offset. 196 */ 197 #define CONFIG_SYS_FLASH_BASE 0xe0000000 198 #ifdef CONFIG_PHYS_64BIT 199 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 200 #else 201 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 202 #endif 203 204 #define CONFIG_SYS_FLASH_BR_PRELIM \ 205 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 206 BR_PS_16 | BR_V) 207 #define CONFIG_SYS_FLASH_OR_PRELIM \ 208 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 209 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 210 211 #define CONFIG_FSL_CPLD 212 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 213 #ifdef CONFIG_PHYS_64BIT 214 #define CPLD_BASE_PHYS 0xfffdf0000ull 215 #else 216 #define CPLD_BASE_PHYS CPLD_BASE 217 #endif 218 219 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 220 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 221 222 #define PIXIS_LBMAP_SWITCH 7 223 #define PIXIS_LBMAP_MASK 0xf0 224 #define PIXIS_LBMAP_SHIFT 4 225 #define PIXIS_LBMAP_ALTBANK 0x40 226 227 #define CONFIG_SYS_FLASH_QUIET_TEST 228 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 229 230 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 231 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 232 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 233 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 234 235 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 236 237 #if defined(CONFIG_RAMBOOT_PBL) 238 #define CONFIG_SYS_RAMBOOT 239 #endif 240 241 #define CONFIG_NAND_FSL_ELBC 242 /* Nand Flash */ 243 #ifdef CONFIG_NAND_FSL_ELBC 244 #define CONFIG_SYS_NAND_BASE 0xffa00000 245 #ifdef CONFIG_PHYS_64BIT 246 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 247 #else 248 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 249 #endif 250 251 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 252 #define CONFIG_SYS_MAX_NAND_DEVICE 1 253 #define CONFIG_CMD_NAND 254 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 255 256 /* NAND flash config */ 257 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 258 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 259 | BR_PS_8 /* Port Size = 8 bit */ \ 260 | BR_MS_FCM /* MSEL = FCM */ \ 261 | BR_V) /* valid */ 262 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 263 | OR_FCM_PGS /* Large Page*/ \ 264 | OR_FCM_CSCT \ 265 | OR_FCM_CST \ 266 | OR_FCM_CHT \ 267 | OR_FCM_SCY_1 \ 268 | OR_FCM_TRLX \ 269 | OR_FCM_EHTR) 270 271 #ifdef CONFIG_NAND 272 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 273 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 274 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 275 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 276 #else 277 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 278 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 279 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 280 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 281 #endif 282 #else 283 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 284 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 285 #endif /* CONFIG_NAND_FSL_ELBC */ 286 287 #define CONFIG_SYS_FLASH_EMPTY_INFO 288 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 289 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 290 291 #define CONFIG_BOARD_EARLY_INIT_F 292 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 293 #define CONFIG_MISC_INIT_R 294 295 #define CONFIG_HWCONFIG 296 297 /* define to use L1 as initial stack */ 298 #define CONFIG_L1_INIT_RAM 299 #define CONFIG_SYS_INIT_RAM_LOCK 300 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 301 #ifdef CONFIG_PHYS_64BIT 302 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 303 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 304 /* The assembler doesn't like typecast */ 305 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 306 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 307 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 308 #else 309 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 310 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 311 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 312 #endif 313 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 314 315 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 316 GENERATED_GBL_DATA_SIZE) 317 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 318 319 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 320 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 321 322 /* Serial Port - controlled on board with jumper J8 323 * open - index 2 324 * shorted - index 1 325 */ 326 #define CONFIG_CONS_INDEX 1 327 #define CONFIG_SYS_NS16550_SERIAL 328 #define CONFIG_SYS_NS16550_REG_SIZE 1 329 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 330 331 #define CONFIG_SYS_BAUDRATE_TABLE \ 332 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 333 334 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 335 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 336 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 337 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 338 339 /* I2C */ 340 #define CONFIG_SYS_I2C 341 #define CONFIG_SYS_I2C_FSL 342 #define CONFIG_SYS_FSL_I2C_SPEED 400000 343 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 344 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 345 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 346 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 347 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 348 349 /* 350 * RapidIO 351 */ 352 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 353 #ifdef CONFIG_PHYS_64BIT 354 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 355 #else 356 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 357 #endif 358 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 359 360 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 361 #ifdef CONFIG_PHYS_64BIT 362 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 363 #else 364 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 365 #endif 366 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 367 368 /* 369 * for slave u-boot IMAGE instored in master memory space, 370 * PHYS must be aligned based on the SIZE 371 */ 372 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 373 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 374 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 375 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 376 /* 377 * for slave UCODE and ENV instored in master memory space, 378 * PHYS must be aligned based on the SIZE 379 */ 380 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 381 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 382 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 383 384 /* slave core release by master*/ 385 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 386 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 387 388 /* 389 * SRIO_PCIE_BOOT - SLAVE 390 */ 391 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 392 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 393 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 394 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 395 #endif 396 397 /* 398 * eSPI - Enhanced SPI 399 */ 400 #define CONFIG_SF_DEFAULT_SPEED 10000000 401 #define CONFIG_SF_DEFAULT_MODE 0 402 403 /* 404 * General PCI 405 * Memory space is mapped 1-1, but I/O space must start from 0. 406 */ 407 408 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 409 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 410 #ifdef CONFIG_PHYS_64BIT 411 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 412 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 413 #else 414 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 415 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 416 #endif 417 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 418 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 419 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 420 #ifdef CONFIG_PHYS_64BIT 421 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 422 #else 423 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 424 #endif 425 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 426 427 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 428 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 429 #ifdef CONFIG_PHYS_64BIT 430 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 431 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 432 #else 433 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 434 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 435 #endif 436 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 437 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 438 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 439 #ifdef CONFIG_PHYS_64BIT 440 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 441 #else 442 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 443 #endif 444 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 445 446 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 447 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 448 #ifdef CONFIG_PHYS_64BIT 449 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 450 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 451 #else 452 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 453 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 454 #endif 455 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 456 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 457 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 458 #ifdef CONFIG_PHYS_64BIT 459 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 460 #else 461 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 462 #endif 463 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 464 465 /* Qman/Bman */ 466 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 467 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 468 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 469 #ifdef CONFIG_PHYS_64BIT 470 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 471 #else 472 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 473 #endif 474 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 475 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 476 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 477 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 478 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 479 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 480 CONFIG_SYS_BMAN_CENA_SIZE) 481 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 482 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 483 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 484 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 485 #ifdef CONFIG_PHYS_64BIT 486 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 487 #else 488 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 489 #endif 490 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 491 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 492 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 493 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 494 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 495 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 496 CONFIG_SYS_QMAN_CENA_SIZE) 497 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 498 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 499 500 #define CONFIG_SYS_DPAA_FMAN 501 #define CONFIG_SYS_DPAA_PME 502 /* Default address of microcode for the Linux Fman driver */ 503 #if defined(CONFIG_SPIFLASH) 504 /* 505 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 506 * env, so we got 0x110000. 507 */ 508 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 509 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 510 #elif defined(CONFIG_SDCARD) 511 /* 512 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 513 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 514 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 515 */ 516 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 517 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 518 #elif defined(CONFIG_NAND) 519 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 520 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 521 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 522 /* 523 * Slave has no ucode locally, it can fetch this from remote. When implementing 524 * in two corenet boards, slave's ucode could be stored in master's memory 525 * space, the address can be mapped from slave TLB->slave LAW-> 526 * slave SRIO or PCIE outbound window->master inbound window-> 527 * master LAW->the ucode address in master's memory space. 528 */ 529 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 530 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 531 #else 532 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 533 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 534 #endif 535 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 536 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 537 538 #ifdef CONFIG_SYS_DPAA_FMAN 539 #define CONFIG_FMAN_ENET 540 #define CONFIG_PHYLIB_10G 541 #define CONFIG_PHY_VITESSE 542 #define CONFIG_PHY_TERANETICS 543 #endif 544 545 #ifdef CONFIG_PCI 546 #define CONFIG_PCI_INDIRECT_BRIDGE 547 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 548 549 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 550 #define CONFIG_DOS_PARTITION 551 #endif /* CONFIG_PCI */ 552 553 /* SATA */ 554 #define CONFIG_FSL_SATA_V2 555 556 #ifdef CONFIG_FSL_SATA_V2 557 #define CONFIG_FSL_SATA 558 #define CONFIG_LIBATA 559 560 #define CONFIG_SYS_SATA_MAX_DEVICE 2 561 #define CONFIG_SATA1 562 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 563 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 564 #define CONFIG_SATA2 565 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 566 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 567 568 #define CONFIG_LBA48 569 #define CONFIG_CMD_SATA 570 #define CONFIG_DOS_PARTITION 571 #endif 572 573 #ifdef CONFIG_FMAN_ENET 574 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 575 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 576 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 577 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 578 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 579 580 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 581 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 582 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 583 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 584 585 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 586 587 #define CONFIG_SYS_TBIPA_VALUE 8 588 #define CONFIG_MII /* MII PHY management */ 589 #define CONFIG_ETHPRIME "FM1@DTSEC1" 590 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 591 #endif 592 593 /* 594 * Environment 595 */ 596 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 597 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 598 599 /* 600 * Command line configuration. 601 */ 602 #define CONFIG_CMD_ERRATA 603 #define CONFIG_CMD_IRQ 604 605 #ifdef CONFIG_PCI 606 #define CONFIG_CMD_PCI 607 #endif 608 609 /* 610 * USB 611 */ 612 #define CONFIG_HAS_FSL_DR_USB 613 #define CONFIG_HAS_FSL_MPH_USB 614 615 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 616 #define CONFIG_USB_STORAGE 617 #define CONFIG_USB_EHCI 618 #define CONFIG_USB_EHCI_FSL 619 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 620 #endif 621 622 #define CONFIG_MMC 623 624 #ifdef CONFIG_MMC 625 #define CONFIG_FSL_ESDHC 626 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 627 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 628 #define CONFIG_GENERIC_MMC 629 #define CONFIG_DOS_PARTITION 630 #endif 631 632 /* Hash command with SHA acceleration supported in hardware */ 633 #ifdef CONFIG_FSL_CAAM 634 #define CONFIG_CMD_HASH 635 #define CONFIG_SHA_HW_ACCEL 636 #endif 637 638 /* 639 * Miscellaneous configurable options 640 */ 641 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 642 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 643 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 644 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 645 #ifdef CONFIG_CMD_KGDB 646 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 647 #else 648 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 649 #endif 650 /* Print Buffer Size */ 651 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 652 sizeof(CONFIG_SYS_PROMPT)+16) 653 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 654 /* Boot Argument Buffer Size */ 655 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 656 657 /* 658 * For booting Linux, the board info and command line data 659 * have to be in the first 64 MB of memory, since this is 660 * the maximum mapped by the Linux kernel during initialization. 661 */ 662 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 663 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 664 665 #ifdef CONFIG_CMD_KGDB 666 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 667 #endif 668 669 /* 670 * Environment Configuration 671 */ 672 #define CONFIG_ROOTPATH "/opt/nfsroot" 673 #define CONFIG_BOOTFILE "uImage" 674 #define CONFIG_UBOOTPATH u-boot.bin 675 676 /* default location for tftp and bootm */ 677 #define CONFIG_LOADADDR 1000000 678 679 680 #define CONFIG_BAUDRATE 115200 681 682 #define __USB_PHY_TYPE utmi 683 684 #define CONFIG_EXTRA_ENV_SETTINGS \ 685 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 686 "bank_intlv=cs0_cs1\0" \ 687 "netdev=eth0\0" \ 688 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 689 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 690 "tftpflash=tftpboot $loadaddr $uboot && " \ 691 "protect off $ubootaddr +$filesize && " \ 692 "erase $ubootaddr +$filesize && " \ 693 "cp.b $loadaddr $ubootaddr $filesize && " \ 694 "protect on $ubootaddr +$filesize && " \ 695 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 696 "consoledev=ttyS0\0" \ 697 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 698 "usb_dr_mode=host\0" \ 699 "ramdiskaddr=2000000\0" \ 700 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 701 "fdtaddr=1e00000\0" \ 702 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 703 "bdev=sda3\0" 704 705 #define CONFIG_HDBOOT \ 706 "setenv bootargs root=/dev/$bdev rw " \ 707 "console=$consoledev,$baudrate $othbootargs;" \ 708 "tftp $loadaddr $bootfile;" \ 709 "tftp $fdtaddr $fdtfile;" \ 710 "bootm $loadaddr - $fdtaddr" 711 712 #define CONFIG_NFSBOOTCOMMAND \ 713 "setenv bootargs root=/dev/nfs rw " \ 714 "nfsroot=$serverip:$rootpath " \ 715 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 716 "console=$consoledev,$baudrate $othbootargs;" \ 717 "tftp $loadaddr $bootfile;" \ 718 "tftp $fdtaddr $fdtfile;" \ 719 "bootm $loadaddr - $fdtaddr" 720 721 #define CONFIG_RAMBOOTCOMMAND \ 722 "setenv bootargs root=/dev/ram rw " \ 723 "console=$consoledev,$baudrate $othbootargs;" \ 724 "tftp $ramdiskaddr $ramdiskfile;" \ 725 "tftp $loadaddr $bootfile;" \ 726 "tftp $fdtaddr $fdtfile;" \ 727 "bootm $loadaddr $ramdiskaddr $fdtaddr" 728 729 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 730 731 #include <asm/fsl_secure_boot.h> 732 733 #endif /* __CONFIG_H */ 734