1 /* 2 * Copyright 2011-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * P2041 RDB board configuration file 9 * Also supports P2040 RDB 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #ifdef CONFIG_RAMBOOT_PBL 15 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 16 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 17 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/corenet_ds/pbi.cfg 18 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/corenet_ds/rcw_p2041rdb.cfg 19 #endif 20 21 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 22 /* Set 1M boot space */ 23 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 24 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 25 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 26 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 27 #endif 28 29 /* High Level Configuration Options */ 30 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 31 #define CONFIG_MP /* support multiple processors */ 32 33 #ifndef CONFIG_SYS_TEXT_BASE 34 #define CONFIG_SYS_TEXT_BASE 0xeff40000 35 #endif 36 37 #ifndef CONFIG_RESET_VECTOR_ADDRESS 38 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 39 #endif 40 41 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 42 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 43 #define CONFIG_PCIE1 /* PCIE controller 1 */ 44 #define CONFIG_PCIE2 /* PCIE controller 2 */ 45 #define CONFIG_PCIE3 /* PCIE controller 3 */ 46 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 47 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 48 49 #define CONFIG_SYS_SRIO 50 #define CONFIG_SRIO1 /* SRIO port 1 */ 51 #define CONFIG_SRIO2 /* SRIO port 2 */ 52 #define CONFIG_SRIO_PCIE_BOOT_MASTER 53 #define CONFIG_SYS_DPAA_RMAN /* RMan */ 54 55 #define CONFIG_ENV_OVERWRITE 56 57 #ifndef CONFIG_MTD_NOR_FLASH 58 #if !defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 59 #define CONFIG_ENV_IS_NOWHERE 60 #endif 61 #else 62 #define CONFIG_FLASH_CFI_DRIVER 63 #define CONFIG_SYS_FLASH_CFI 64 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 65 #endif 66 67 #if defined(CONFIG_SPIFLASH) 68 #define CONFIG_SYS_EXTRA_ENV_RELOC 69 #define CONFIG_ENV_IS_IN_SPI_FLASH 70 #define CONFIG_ENV_SPI_BUS 0 71 #define CONFIG_ENV_SPI_CS 0 72 #define CONFIG_ENV_SPI_MAX_HZ 10000000 73 #define CONFIG_ENV_SPI_MODE 0 74 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 75 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 76 #define CONFIG_ENV_SECT_SIZE 0x10000 77 #elif defined(CONFIG_SDCARD) 78 #define CONFIG_SYS_EXTRA_ENV_RELOC 79 #define CONFIG_ENV_IS_IN_MMC 80 #define CONFIG_FSL_FIXED_MMC_LOCATION 81 #define CONFIG_SYS_MMC_ENV_DEV 0 82 #define CONFIG_ENV_SIZE 0x2000 83 #define CONFIG_ENV_OFFSET (512 * 1658) 84 #elif defined(CONFIG_NAND) 85 #define CONFIG_SYS_EXTRA_ENV_RELOC 86 #define CONFIG_ENV_IS_IN_NAND 87 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 88 #define CONFIG_ENV_OFFSET (7 * CONFIG_SYS_NAND_BLOCK_SIZE) 89 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 90 #define CONFIG_ENV_IS_IN_REMOTE 91 #define CONFIG_ENV_ADDR 0xffe20000 92 #define CONFIG_ENV_SIZE 0x2000 93 #elif defined(CONFIG_ENV_IS_NOWHERE) 94 #define CONFIG_ENV_SIZE 0x2000 95 #else 96 #define CONFIG_ENV_IS_IN_FLASH 97 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \ 98 - CONFIG_ENV_SECT_SIZE) 99 #define CONFIG_ENV_SIZE 0x2000 100 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 101 #endif 102 103 #ifndef __ASSEMBLY__ 104 unsigned long get_board_sys_clk(unsigned long dummy); 105 #endif 106 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 107 108 /* 109 * These can be toggled for performance analysis, otherwise use default. 110 */ 111 #define CONFIG_SYS_CACHE_STASHING 112 #define CONFIG_BACKSIDE_L2_CACHE 113 #define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E 114 #define CONFIG_BTB /* toggle branch predition */ 115 116 #define CONFIG_ENABLE_36BIT_PHYS 117 118 #ifdef CONFIG_PHYS_64BIT 119 #define CONFIG_ADDR_MAP 120 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 121 #endif 122 123 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 124 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 125 #define CONFIG_SYS_MEMTEST_END 0x00400000 126 #define CONFIG_SYS_ALT_MEMTEST 127 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 128 129 /* 130 * Config the L3 Cache as L3 SRAM 131 */ 132 #define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE 133 #ifdef CONFIG_PHYS_64BIT 134 #define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ 135 CONFIG_RAMBOOT_TEXT_BASE) 136 #else 137 #define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR 138 #endif 139 #define CONFIG_SYS_L3_SIZE (1024 << 10) 140 #define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) 141 142 #ifdef CONFIG_PHYS_64BIT 143 #define CONFIG_SYS_DCSRBAR 0xf0000000 144 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 145 #endif 146 147 /* EEPROM */ 148 #define CONFIG_ID_EEPROM 149 #define CONFIG_SYS_I2C_EEPROM_NXID 150 #define CONFIG_SYS_EEPROM_BUS_NUM 0 151 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 152 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 153 154 /* 155 * DDR Setup 156 */ 157 #define CONFIG_VERY_BIG_RAM 158 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 159 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 160 161 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 162 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 163 164 #define CONFIG_DDR_SPD 165 166 #define CONFIG_SYS_SPD_BUS_NUM 0 167 #define SPD_EEPROM_ADDRESS 0x52 168 #define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ 169 170 /* 171 * Local Bus Definitions 172 */ 173 174 /* Set the local bus clock 1/8 of platform clock */ 175 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 176 177 /* 178 * This board doesn't have a promjet connector. 179 * However, it uses commone corenet board LAW and TLB. 180 * It is necessary to use the same start address with proper offset. 181 */ 182 #define CONFIG_SYS_FLASH_BASE 0xe0000000 183 #ifdef CONFIG_PHYS_64BIT 184 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 185 #else 186 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 187 #endif 188 189 #define CONFIG_SYS_FLASH_BR_PRELIM \ 190 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ 191 BR_PS_16 | BR_V) 192 #define CONFIG_SYS_FLASH_OR_PRELIM \ 193 ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ 194 | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) 195 196 #define CONFIG_FSL_CPLD 197 #define CPLD_BASE 0xffdf0000 /* CPLD registers */ 198 #ifdef CONFIG_PHYS_64BIT 199 #define CPLD_BASE_PHYS 0xfffdf0000ull 200 #else 201 #define CPLD_BASE_PHYS CPLD_BASE 202 #endif 203 204 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(CPLD_BASE_PHYS) | BR_PS_8 | BR_V) 205 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 206 207 #define PIXIS_LBMAP_SWITCH 7 208 #define PIXIS_LBMAP_MASK 0xf0 209 #define PIXIS_LBMAP_SHIFT 4 210 #define PIXIS_LBMAP_ALTBANK 0x40 211 212 #define CONFIG_SYS_FLASH_QUIET_TEST 213 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 214 215 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 216 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 217 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Erase Timeout (ms) */ 218 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (ms) */ 219 220 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE 221 222 #if defined(CONFIG_RAMBOOT_PBL) 223 #define CONFIG_SYS_RAMBOOT 224 #endif 225 226 #define CONFIG_NAND_FSL_ELBC 227 /* Nand Flash */ 228 #ifdef CONFIG_NAND_FSL_ELBC 229 #define CONFIG_SYS_NAND_BASE 0xffa00000 230 #ifdef CONFIG_PHYS_64BIT 231 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 232 #else 233 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 234 #endif 235 236 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} 237 #define CONFIG_SYS_MAX_NAND_DEVICE 1 238 #define CONFIG_CMD_NAND 239 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 240 241 /* NAND flash config */ 242 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 243 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 244 | BR_PS_8 /* Port Size = 8 bit */ \ 245 | BR_MS_FCM /* MSEL = FCM */ \ 246 | BR_V) /* valid */ 247 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 248 | OR_FCM_PGS /* Large Page*/ \ 249 | OR_FCM_CSCT \ 250 | OR_FCM_CST \ 251 | OR_FCM_CHT \ 252 | OR_FCM_SCY_1 \ 253 | OR_FCM_TRLX \ 254 | OR_FCM_EHTR) 255 256 #ifdef CONFIG_NAND 257 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 258 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 259 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 260 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 261 #else 262 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 263 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 264 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 265 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 266 #endif 267 #else 268 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_FLASH_BR_PRELIM /* NOR Base Address */ 269 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_FLASH_OR_PRELIM /* NOR Options */ 270 #endif /* CONFIG_NAND_FSL_ELBC */ 271 272 #define CONFIG_SYS_FLASH_EMPTY_INFO 273 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 274 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} 275 276 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 277 #define CONFIG_MISC_INIT_R 278 279 #define CONFIG_HWCONFIG 280 281 /* define to use L1 as initial stack */ 282 #define CONFIG_L1_INIT_RAM 283 #define CONFIG_SYS_INIT_RAM_LOCK 284 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 285 #ifdef CONFIG_PHYS_64BIT 286 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 287 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR 288 /* The assembler doesn't like typecast */ 289 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 290 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 291 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 292 #else 293 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR 294 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 295 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 296 #endif 297 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 298 299 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 300 GENERATED_GBL_DATA_SIZE) 301 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 302 303 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 304 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) 305 306 /* Serial Port - controlled on board with jumper J8 307 * open - index 2 308 * shorted - index 1 309 */ 310 #define CONFIG_CONS_INDEX 1 311 #define CONFIG_SYS_NS16550_SERIAL 312 #define CONFIG_SYS_NS16550_REG_SIZE 1 313 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 314 315 #define CONFIG_SYS_BAUDRATE_TABLE \ 316 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 317 318 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 319 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 320 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 321 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 322 323 /* I2C */ 324 #define CONFIG_SYS_I2C 325 #define CONFIG_SYS_I2C_FSL 326 #define CONFIG_SYS_FSL_I2C_SPEED 400000 327 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 328 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 329 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 330 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 331 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 332 333 /* 334 * RapidIO 335 */ 336 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 337 #ifdef CONFIG_PHYS_64BIT 338 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 339 #else 340 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 341 #endif 342 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 343 344 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 345 #ifdef CONFIG_PHYS_64BIT 346 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 347 #else 348 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 349 #endif 350 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 351 352 /* 353 * for slave u-boot IMAGE instored in master memory space, 354 * PHYS must be aligned based on the SIZE 355 */ 356 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 357 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 358 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 359 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 360 /* 361 * for slave UCODE and ENV instored in master memory space, 362 * PHYS must be aligned based on the SIZE 363 */ 364 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 365 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 366 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 367 368 /* slave core release by master*/ 369 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 370 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 371 372 /* 373 * SRIO_PCIE_BOOT - SLAVE 374 */ 375 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 376 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 377 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 378 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 379 #endif 380 381 /* 382 * eSPI - Enhanced SPI 383 */ 384 #define CONFIG_SF_DEFAULT_SPEED 10000000 385 #define CONFIG_SF_DEFAULT_MODE 0 386 387 /* 388 * General PCI 389 * Memory space is mapped 1-1, but I/O space must start from 0. 390 */ 391 392 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 393 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 394 #ifdef CONFIG_PHYS_64BIT 395 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 396 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 397 #else 398 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 399 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 400 #endif 401 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 402 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 403 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 404 #ifdef CONFIG_PHYS_64BIT 405 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 406 #else 407 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 408 #endif 409 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 410 411 /* controller 2, Slot 2, tgtid 2, Base address 201000 */ 412 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 413 #ifdef CONFIG_PHYS_64BIT 414 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 415 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 416 #else 417 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 418 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 419 #endif 420 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 421 #define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000 422 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 423 #ifdef CONFIG_PHYS_64BIT 424 #define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull 425 #else 426 #define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000 427 #endif 428 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 429 430 /* controller 3, Slot 1, tgtid 1, Base address 202000 */ 431 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000 432 #ifdef CONFIG_PHYS_64BIT 433 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 434 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull 435 #else 436 #define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000 437 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000 438 #endif 439 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 440 #define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000 441 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 442 #ifdef CONFIG_PHYS_64BIT 443 #define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull 444 #else 445 #define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000 446 #endif 447 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 448 449 /* Qman/Bman */ 450 #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ 451 #define CONFIG_SYS_BMAN_NUM_PORTALS 10 452 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 453 #ifdef CONFIG_PHYS_64BIT 454 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 455 #else 456 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 457 #endif 458 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 459 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 460 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 461 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 462 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 463 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 464 CONFIG_SYS_BMAN_CENA_SIZE) 465 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 466 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 467 #define CONFIG_SYS_QMAN_NUM_PORTALS 10 468 #define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 469 #ifdef CONFIG_PHYS_64BIT 470 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull 471 #else 472 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 473 #endif 474 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 475 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 476 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 477 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 478 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 479 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 480 CONFIG_SYS_QMAN_CENA_SIZE) 481 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 482 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 483 484 #define CONFIG_SYS_DPAA_FMAN 485 #define CONFIG_SYS_DPAA_PME 486 /* Default address of microcode for the Linux Fman driver */ 487 #if defined(CONFIG_SPIFLASH) 488 /* 489 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 490 * env, so we got 0x110000. 491 */ 492 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 493 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 494 #elif defined(CONFIG_SDCARD) 495 /* 496 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 497 * about 825KB (1650 blocks), Env is stored after the image, and the env size is 498 * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680. 499 */ 500 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 501 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680) 502 #elif defined(CONFIG_NAND) 503 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 504 #define CONFIG_SYS_FMAN_FW_ADDR (8 * CONFIG_SYS_NAND_BLOCK_SIZE) 505 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 506 /* 507 * Slave has no ucode locally, it can fetch this from remote. When implementing 508 * in two corenet boards, slave's ucode could be stored in master's memory 509 * space, the address can be mapped from slave TLB->slave LAW-> 510 * slave SRIO or PCIE outbound window->master inbound window-> 511 * master LAW->the ucode address in master's memory space. 512 */ 513 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 514 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 515 #else 516 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 517 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 518 #endif 519 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 520 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 521 522 #ifdef CONFIG_SYS_DPAA_FMAN 523 #define CONFIG_FMAN_ENET 524 #define CONFIG_PHYLIB_10G 525 #define CONFIG_PHY_VITESSE 526 #define CONFIG_PHY_TERANETICS 527 #endif 528 529 #ifdef CONFIG_PCI 530 #define CONFIG_PCI_INDIRECT_BRIDGE 531 532 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 533 #endif /* CONFIG_PCI */ 534 535 /* SATA */ 536 #define CONFIG_FSL_SATA_V2 537 538 #ifdef CONFIG_FSL_SATA_V2 539 #define CONFIG_FSL_SATA 540 #define CONFIG_LIBATA 541 542 #define CONFIG_SYS_SATA_MAX_DEVICE 2 543 #define CONFIG_SATA1 544 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 545 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 546 #define CONFIG_SATA2 547 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 548 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 549 550 #define CONFIG_LBA48 551 #define CONFIG_CMD_SATA 552 #endif 553 554 #ifdef CONFIG_FMAN_ENET 555 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2 556 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x3 557 #define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR 0x4 558 #define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR 0x1 559 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x0 560 561 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 562 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 563 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 564 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 565 566 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0 567 568 #define CONFIG_SYS_TBIPA_VALUE 8 569 #define CONFIG_MII /* MII PHY management */ 570 #define CONFIG_ETHPRIME "FM1@DTSEC1" 571 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 572 #endif 573 574 /* 575 * Environment 576 */ 577 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 578 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 579 580 /* 581 * Command line configuration. 582 */ 583 #define CONFIG_CMD_ERRATA 584 #define CONFIG_CMD_IRQ 585 586 #ifdef CONFIG_PCI 587 #define CONFIG_CMD_PCI 588 #endif 589 590 /* 591 * USB 592 */ 593 #define CONFIG_HAS_FSL_DR_USB 594 #define CONFIG_HAS_FSL_MPH_USB 595 596 #if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) 597 #define CONFIG_USB_EHCI_FSL 598 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 599 #endif 600 601 #ifdef CONFIG_MMC 602 #define CONFIG_FSL_ESDHC 603 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 604 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT 605 #endif 606 607 /* Hash command with SHA acceleration supported in hardware */ 608 #ifdef CONFIG_FSL_CAAM 609 #define CONFIG_CMD_HASH 610 #endif 611 612 /* 613 * Miscellaneous configurable options 614 */ 615 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 616 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 617 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 618 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 619 #ifdef CONFIG_CMD_KGDB 620 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 621 #else 622 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 623 #endif 624 /* Print Buffer Size */ 625 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 626 sizeof(CONFIG_SYS_PROMPT)+16) 627 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 628 /* Boot Argument Buffer Size */ 629 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 630 631 /* 632 * For booting Linux, the board info and command line data 633 * have to be in the first 64 MB of memory, since this is 634 * the maximum mapped by the Linux kernel during initialization. 635 */ 636 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ 637 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 638 639 #ifdef CONFIG_CMD_KGDB 640 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 641 #endif 642 643 /* 644 * Environment Configuration 645 */ 646 #define CONFIG_ROOTPATH "/opt/nfsroot" 647 #define CONFIG_BOOTFILE "uImage" 648 #define CONFIG_UBOOTPATH u-boot.bin 649 650 /* default location for tftp and bootm */ 651 #define CONFIG_LOADADDR 1000000 652 653 #define __USB_PHY_TYPE utmi 654 655 #define CONFIG_EXTRA_ENV_SETTINGS \ 656 "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \ 657 "bank_intlv=cs0_cs1\0" \ 658 "netdev=eth0\0" \ 659 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 660 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 661 "tftpflash=tftpboot $loadaddr $uboot && " \ 662 "protect off $ubootaddr +$filesize && " \ 663 "erase $ubootaddr +$filesize && " \ 664 "cp.b $loadaddr $ubootaddr $filesize && " \ 665 "protect on $ubootaddr +$filesize && " \ 666 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 667 "consoledev=ttyS0\0" \ 668 "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ 669 "usb_dr_mode=host\0" \ 670 "ramdiskaddr=2000000\0" \ 671 "ramdiskfile=p2041rdb/ramdisk.uboot\0" \ 672 "fdtaddr=1e00000\0" \ 673 "fdtfile=p2041rdb/p2041rdb.dtb\0" \ 674 "bdev=sda3\0" 675 676 #define CONFIG_HDBOOT \ 677 "setenv bootargs root=/dev/$bdev rw " \ 678 "console=$consoledev,$baudrate $othbootargs;" \ 679 "tftp $loadaddr $bootfile;" \ 680 "tftp $fdtaddr $fdtfile;" \ 681 "bootm $loadaddr - $fdtaddr" 682 683 #define CONFIG_NFSBOOTCOMMAND \ 684 "setenv bootargs root=/dev/nfs rw " \ 685 "nfsroot=$serverip:$rootpath " \ 686 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 687 "console=$consoledev,$baudrate $othbootargs;" \ 688 "tftp $loadaddr $bootfile;" \ 689 "tftp $fdtaddr $fdtfile;" \ 690 "bootm $loadaddr - $fdtaddr" 691 692 #define CONFIG_RAMBOOTCOMMAND \ 693 "setenv bootargs root=/dev/ram rw " \ 694 "console=$consoledev,$baudrate $othbootargs;" \ 695 "tftp $ramdiskaddr $ramdiskfile;" \ 696 "tftp $loadaddr $bootfile;" \ 697 "tftp $fdtaddr $fdtfile;" \ 698 "bootm $loadaddr $ramdiskaddr $fdtaddr" 699 700 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 701 702 #include <asm/fsl_secure_boot.h> 703 704 #endif /* __CONFIG_H */ 705