1 /* 2 * Copyright 2013 Freescale Semiconductor, Inc. 3 * 4 * Authors: Roy Zang <tie-fei.zang@freescale.com> 5 * Chunhe Lan <Chunhe.Lan@freescale.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #define CONFIG_SYS_GENERIC_BOARD 14 #define CONFIG_DISPLAY_BOARDINFO 15 16 #ifndef CONFIG_SYS_TEXT_BASE 17 #define CONFIG_SYS_TEXT_BASE 0xeff40000 18 #endif 19 20 #ifndef CONFIG_SYS_MONITOR_BASE 21 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 22 #endif 23 24 #ifndef CONFIG_RESET_VECTOR_ADDRESS 25 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 26 #endif 27 28 /* High Level Configuration Options */ 29 #define CONFIG_BOOKE /* BOOKE */ 30 #define CONFIG_E500 /* BOOKE e500 family */ 31 #define CONFIG_P1023 32 #define CONFIG_MP /* support multiple processors */ 33 34 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 35 #define CONFIG_PCI /* Enable PCI/PCIE */ 36 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 37 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 38 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ 39 #define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */ 40 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 41 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 42 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 43 #define CONFIG_FSL_LAW /* Use common FSL init code */ 44 45 #ifndef __ASSEMBLY__ 46 extern unsigned long get_clock_freq(void); 47 #endif 48 49 #define CONFIG_SYS_CLK_FREQ 66666666 50 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 51 52 /* 53 * These can be toggled for performance analysis, otherwise use default. 54 */ 55 #define CONFIG_L2_CACHE /* toggle L2 cache */ 56 #define CONFIG_BTB /* toggle branch predition */ 57 #define CONFIG_HWCONFIG 58 59 #define CONFIG_ENABLE_36BIT_PHYS 60 61 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 62 #define CONFIG_SYS_MEMTEST_END 0x02000000 63 64 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 65 66 /* Implement conversion of addresses in the LBC */ 67 #define CONFIG_SYS_LBC_LBCR 0x00000000 68 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 69 70 /* DDR Setup */ 71 #define CONFIG_VERY_BIG_RAM 72 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 73 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 74 75 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 76 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 77 78 #define CONFIG_DDR_SPD 79 #define CONFIG_SYS_FSL_DDR3 80 #define CONFIG_FSL_DDR_INTERACTIVE 81 #define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */ 82 #define CONFIG_SYS_SPD_BUS_NUM 0 83 #define SPD_EEPROM_ADDRESS 0x50 84 #define CONFIG_SYS_DDR_RAW_TIMING 85 86 /* 87 * Memory map 88 * 89 * 0x0000_0000 0x1fff_ffff DDR 512M cacheable 90 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable 91 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable 92 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable 93 * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable 94 * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable 95 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0 96 * 97 * Localbus non-cacheable 98 * 99 * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable 100 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable 101 */ 102 103 /* 104 * Local Bus Definitions 105 */ 106 #define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */ 107 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 108 109 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 110 | BR_PS_16 | BR_V) 111 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 112 113 #define CONFIG_FLASH_CFI_DRIVER 114 #define CONFIG_SYS_FLASH_CFI 115 #define CONFIG_SYS_FLASH_EMPTY_INFO 116 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 117 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 118 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 119 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 120 121 #define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */ 122 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 123 124 #define CONFIG_SYS_INIT_RAM_LOCK 125 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 126 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */ 127 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 128 GENERATED_GBL_DATA_SIZE) 129 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 130 131 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */ 132 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ 133 134 #define CONFIG_SYS_NAND_BASE 0xffa00000 135 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 136 137 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 138 #define CONFIG_SYS_MAX_NAND_DEVICE 1 139 #define CONFIG_CMD_NAND 140 #define CONFIG_NAND_FSL_ELBC 141 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 142 143 /* NAND flash config */ 144 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 145 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 146 | BR_PS_8 /* Port Size = 8bit */ \ 147 | BR_MS_FCM /* MSEL = FCM */ \ 148 | BR_V) /* valid */ 149 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ 150 | OR_FCM_PGS \ 151 | OR_FCM_CSCT \ 152 | OR_FCM_CST \ 153 | OR_FCM_CHT \ 154 | OR_FCM_SCY_1 \ 155 | OR_FCM_TRLX \ 156 | OR_FCM_EHTR) 157 158 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 159 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 160 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 161 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 162 163 /* Serial Port */ 164 #define CONFIG_CONS_INDEX 1 165 #undef CONFIG_SERIAL_SOFTWARE_FIFO 166 #define CONFIG_SYS_NS16550 167 #define CONFIG_SYS_NS16550_SERIAL 168 #define CONFIG_SYS_NS16550_REG_SIZE 1 169 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 170 171 #define CONFIG_SYS_BAUDRATE_TABLE \ 172 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 173 174 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 175 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 176 177 /* Use the HUSH parser */ 178 #define CONFIG_SYS_HUSH_PARSER 179 180 /* 181 * Pass open firmware flat tree 182 */ 183 #define CONFIG_OF_LIBFDT 184 #define CONFIG_OF_BOARD_SETUP 185 #define CONFIG_OF_STDOUT_VIA_ALIAS 186 187 /* new uImage format support */ 188 #define CONFIG_FIT 189 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 190 191 /* I2C */ 192 #define CONFIG_SYS_I2C 193 #define CONFIG_SYS_I2C_FSL 194 #define CONFIG_SYS_FSL_I2C_SPEED 400000 195 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 196 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 197 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 198 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 199 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 200 201 /* 202 * I2C2 EEPROM 203 */ 204 #define CONFIG_ID_EEPROM 205 #ifdef CONFIG_ID_EEPROM 206 #define CONFIG_SYS_I2C_EEPROM_NXID 207 #endif 208 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 209 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 210 #define CONFIG_SYS_EEPROM_BUS_NUM 0 211 212 #define CONFIG_CMD_I2C 213 214 /* 215 * General PCI 216 * Memory space is mapped 1-1, but I/O space must start from 0. 217 */ 218 219 /* controller 3, Slot 1, tgtid 3, Base address b000 */ 220 #define CONFIG_SYS_PCIE3_NAME "Slot 3" 221 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 222 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 223 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 224 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 225 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 226 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 227 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 228 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 229 230 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 231 #define CONFIG_SYS_PCIE2_NAME "Slot 2" 232 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 233 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 234 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 235 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 236 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 237 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 238 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 239 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 240 241 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 242 #define CONFIG_SYS_PCIE1_NAME "Slot 1" 243 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 244 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 245 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 246 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 247 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 248 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 249 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 250 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 251 252 #if defined(CONFIG_PCI) 253 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 254 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 255 #endif /* CONFIG_PCI */ 256 257 /* 258 * Environment 259 */ 260 #define CONFIG_ENV_OVERWRITE 261 262 #define CONFIG_ENV_IS_IN_FLASH 263 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 264 #define CONFIG_ENV_SIZE 0x2000 265 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 266 267 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 268 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 269 270 /* 271 * Command line configuration. 272 */ 273 #define CONFIG_CMD_IRQ 274 #define CONFIG_CMD_PING 275 #define CONFIG_CMD_MII 276 #define CONFIG_CMD_REGINFO 277 278 #if defined(CONFIG_PCI) 279 #define CONFIG_CMD_PCI 280 #endif 281 282 /* 283 * USB 284 */ 285 #define CONFIG_HAS_FSL_DR_USB 286 #ifdef CONFIG_HAS_FSL_DR_USB 287 #define CONFIG_USB_EHCI 288 289 #ifdef CONFIG_USB_EHCI 290 #define CONFIG_CMD_USB 291 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 292 #define CONFIG_USB_EHCI_FSL 293 #define CONFIG_USB_STORAGE 294 #define CONFIG_CMD_FAT 295 #define CONFIG_CMD_EXT2 296 #define CONFIG_CMD_FAT 297 #define CONFIG_DOS_PARTITION 298 #endif 299 #endif 300 301 /* 302 * Miscellaneous configurable options 303 */ 304 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 305 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 306 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 307 #if defined(CONFIG_CMD_KGDB) 308 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 309 #else 310 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 311 #endif 312 /* Print Buffer Size */ 313 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) 314 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 315 /* Boot Argument Buffer Size */ 316 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 317 318 /* 319 * For booting Linux, the board info and command line data 320 * have to be in the first 64 MB of memory, since this is 321 * the maximum mapped by the Linux kernel during initialization. 322 */ 323 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 324 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 325 326 /* 327 * Environment Configuration 328 */ 329 #define CONFIG_BOOTFILE "uImage" 330 #define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */ 331 332 /* default location for tftp and bootm */ 333 #define CONFIG_LOADADDR 1000000 334 335 #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ 336 337 #define CONFIG_BAUDRATE 115200 338 339 /* Qman/Bman */ 340 #define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */ 341 #define CONFIG_SYS_QMAN_MEM_BASE 0xff000000 342 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 343 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 344 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 345 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 346 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 347 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 348 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 349 CONFIG_SYS_QMAN_CENA_SIZE) 350 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 351 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 352 #define CONFIG_SYS_BMAN_MEM_BASE 0xff200000 353 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 354 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 355 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 356 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 357 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 358 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 359 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 360 CONFIG_SYS_BMAN_CENA_SIZE) 361 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 362 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 363 364 /* For FM */ 365 #define CONFIG_SYS_DPAA_FMAN 366 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 367 368 #ifdef CONFIG_SYS_DPAA_FMAN 369 #define CONFIG_FMAN_ENET 370 #define CONFIG_PHY_ATHEROS 371 #endif 372 373 /* Default address of microcode for the Linux Fman driver */ 374 /* QE microcode/firmware address */ 375 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 376 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 377 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 378 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 379 380 #ifdef CONFIG_FMAN_ENET 381 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1 382 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2 383 384 #define CONFIG_SYS_TBIPA_VALUE 8 385 #define CONFIG_MII /* MII PHY management */ 386 #define CONFIG_ETHPRIME "FM1@DTSEC1" 387 #endif 388 389 #define CONFIG_EXTRA_ENV_SETTINGS \ 390 "netdev=eth0\0" \ 391 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 392 "loadaddr=1000000\0" \ 393 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 394 "tftpflash=tftpboot $loadaddr $uboot; " \ 395 "protect off $ubootaddr +$filesize; " \ 396 "erase $ubootaddr +$filesize; " \ 397 "cp.b $loadaddr $ubootaddr $filesize; " \ 398 "protect on $ubootaddr +$filesize; " \ 399 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 400 "consoledev=ttyS0\0" \ 401 "ramdiskaddr=2000000\0" \ 402 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 403 "fdtaddr=c00000\0" \ 404 "fdtfile=p1023rdb.dtb\0" \ 405 "othbootargs=ramdisk_size=600000\0" \ 406 "bdev=sda1\0" \ 407 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" 408 409 #define CONFIG_HDBOOT \ 410 "setenv bootargs root=/dev/$bdev rw " \ 411 "console=$consoledev,$baudrate $othbootargs;" \ 412 "tftp $loadaddr $bootfile;" \ 413 "tftp $fdtaddr $fdtfile;" \ 414 "bootm $loadaddr - $fdtaddr" 415 416 #define CONFIG_NFSBOOTCOMMAND \ 417 "setenv bootargs root=/dev/nfs rw " \ 418 "nfsroot=$serverip:$rootpath " \ 419 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 420 "console=$consoledev,$baudrate $othbootargs;" \ 421 "tftp $loadaddr $bootfile;" \ 422 "tftp $fdtaddr $fdtfile;" \ 423 "bootm $loadaddr - $fdtaddr" 424 425 #define CONFIG_RAMBOOTCOMMAND \ 426 "setenv bootargs root=/dev/ram rw " \ 427 "console=$consoledev,$baudrate $othbootargs;" \ 428 "tftp $ramdiskaddr $ramdiskfile;" \ 429 "tftp $loadaddr $bootfile;" \ 430 "tftp $fdtaddr $fdtfile;" \ 431 "bootm $loadaddr $ramdiskaddr $fdtaddr" 432 433 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 434 435 #endif /* __CONFIG_H */ 436