1 /* 2 * Copyright 2013 Freescale Semiconductor, Inc. 3 * 4 * Authors: Roy Zang <tie-fei.zang@freescale.com> 5 * Chunhe Lan <Chunhe.Lan@freescale.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #ifndef CONFIG_SYS_TEXT_BASE 14 #define CONFIG_SYS_TEXT_BASE 0xeff40000 15 #endif 16 17 #ifndef CONFIG_SYS_MONITOR_BASE 18 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 19 #endif 20 21 #ifndef CONFIG_RESET_VECTOR_ADDRESS 22 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 23 #endif 24 25 /* High Level Configuration Options */ 26 #define CONFIG_BOOKE /* BOOKE */ 27 #define CONFIG_E500 /* BOOKE e500 family */ 28 #define CONFIG_P1023 29 #define CONFIG_MP /* support multiple processors */ 30 31 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 32 #define CONFIG_PCI /* Enable PCI/PCIE */ 33 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 34 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 35 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ 36 #define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */ 37 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 38 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 39 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 40 #define CONFIG_FSL_LAW /* Use common FSL init code */ 41 42 #ifndef __ASSEMBLY__ 43 extern unsigned long get_clock_freq(void); 44 #endif 45 46 #define CONFIG_SYS_CLK_FREQ 66666666 47 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 48 49 /* 50 * These can be toggled for performance analysis, otherwise use default. 51 */ 52 #define CONFIG_L2_CACHE /* toggle L2 cache */ 53 #define CONFIG_BTB /* toggle branch predition */ 54 #define CONFIG_HWCONFIG 55 56 #define CONFIG_ENABLE_36BIT_PHYS 57 58 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 59 #define CONFIG_SYS_MEMTEST_END 0x02000000 60 61 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 62 63 /* Implement conversion of addresses in the LBC */ 64 #define CONFIG_SYS_LBC_LBCR 0x00000000 65 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 66 67 /* DDR Setup */ 68 #define CONFIG_VERY_BIG_RAM 69 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 70 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 71 72 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 73 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 74 75 #define CONFIG_DDR_SPD 76 #define CONFIG_SYS_FSL_DDR3 77 #define CONFIG_FSL_DDR_INTERACTIVE 78 #define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */ 79 #define CONFIG_SYS_SPD_BUS_NUM 0 80 #define SPD_EEPROM_ADDRESS 0x50 81 #define CONFIG_SYS_DDR_RAW_TIMING 82 83 /* 84 * Memory map 85 * 86 * 0x0000_0000 0x1fff_ffff DDR 512M cacheable 87 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable 88 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable 89 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable 90 * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable 91 * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable 92 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0 93 * 94 * Localbus non-cacheable 95 * 96 * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable 97 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable 98 */ 99 100 /* 101 * Local Bus Definitions 102 */ 103 #define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */ 104 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 105 106 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 107 | BR_PS_16 | BR_V) 108 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 109 110 #define CONFIG_FLASH_CFI_DRIVER 111 #define CONFIG_SYS_FLASH_CFI 112 #define CONFIG_SYS_FLASH_EMPTY_INFO 113 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 114 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 115 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 116 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 117 118 #define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */ 119 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 120 121 #define CONFIG_SYS_INIT_RAM_LOCK 122 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 123 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */ 124 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 125 GENERATED_GBL_DATA_SIZE) 126 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 127 128 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */ 129 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ 130 131 #define CONFIG_SYS_NAND_BASE 0xffa00000 132 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 133 134 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 135 #define CONFIG_SYS_MAX_NAND_DEVICE 1 136 #define CONFIG_MTD_NAND_VERIFY_WRITE 137 #define CONFIG_CMD_NAND 138 #define CONFIG_NAND_FSL_ELBC 139 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 140 141 /* NAND flash config */ 142 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 143 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 144 | BR_PS_8 /* Port Size = 8bit */ \ 145 | BR_MS_FCM /* MSEL = FCM */ \ 146 | BR_V) /* valid */ 147 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ 148 | OR_FCM_PGS \ 149 | OR_FCM_CSCT \ 150 | OR_FCM_CST \ 151 | OR_FCM_CHT \ 152 | OR_FCM_SCY_1 \ 153 | OR_FCM_TRLX \ 154 | OR_FCM_EHTR) 155 156 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 157 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 158 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 159 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 160 161 /* Serial Port */ 162 #define CONFIG_CONS_INDEX 1 163 #undef CONFIG_SERIAL_SOFTWARE_FIFO 164 #define CONFIG_SYS_NS16550 165 #define CONFIG_SYS_NS16550_SERIAL 166 #define CONFIG_SYS_NS16550_REG_SIZE 1 167 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 168 169 #define CONFIG_SYS_BAUDRATE_TABLE \ 170 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 171 172 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 173 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 174 175 /* Use the HUSH parser */ 176 #define CONFIG_SYS_HUSH_PARSER 177 178 /* 179 * Pass open firmware flat tree 180 */ 181 #define CONFIG_OF_LIBFDT 182 #define CONFIG_OF_BOARD_SETUP 183 #define CONFIG_OF_STDOUT_VIA_ALIAS 184 185 /* new uImage format support */ 186 #define CONFIG_FIT 187 #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ 188 189 /* I2C */ 190 #define CONFIG_SYS_I2C 191 #define CONFIG_SYS_I2C_FSL 192 #define CONFIG_SYS_FSL_I2C_SPEED 400000 193 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 194 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 195 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 196 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 197 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 198 199 /* 200 * I2C2 EEPROM 201 */ 202 #define CONFIG_ID_EEPROM 203 #ifdef CONFIG_ID_EEPROM 204 #define CONFIG_SYS_I2C_EEPROM_NXID 205 #endif 206 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 207 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 208 #define CONFIG_SYS_EEPROM_BUS_NUM 0 209 210 #define CONFIG_CMD_I2C 211 212 /* 213 * General PCI 214 * Memory space is mapped 1-1, but I/O space must start from 0. 215 */ 216 217 /* controller 3, Slot 1, tgtid 3, Base address b000 */ 218 #define CONFIG_SYS_PCIE3_NAME "Slot 3" 219 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 220 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 221 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 222 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 223 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 224 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 225 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 226 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 227 228 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 229 #define CONFIG_SYS_PCIE2_NAME "Slot 2" 230 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 231 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 232 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 233 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 234 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 235 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 236 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 237 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 238 239 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 240 #define CONFIG_SYS_PCIE1_NAME "Slot 1" 241 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 242 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 243 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 244 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 245 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 246 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 247 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 248 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 249 250 #if defined(CONFIG_PCI) 251 #define CONFIG_E1000 /* Defind e1000 pci Ethernet card */ 252 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 253 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 254 #endif /* CONFIG_PCI */ 255 256 /* 257 * Environment 258 */ 259 #define CONFIG_ENV_OVERWRITE 260 261 #define CONFIG_ENV_IS_IN_FLASH 262 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 263 #define CONFIG_ENV_SIZE 0x2000 264 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 265 266 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 267 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 268 269 /* 270 * Command line configuration. 271 */ 272 #include <config_cmd_default.h> 273 274 #define CONFIG_CMD_IRQ 275 #define CONFIG_CMD_PING 276 #define CONFIG_CMD_MII 277 #define CONFIG_CMD_SETEXPR 278 #define CONFIG_CMD_REGINFO 279 280 #if defined(CONFIG_PCI) 281 #define CONFIG_CMD_PCI 282 #define CONFIG_CMD_NET 283 #endif 284 285 /* 286 * USB 287 */ 288 #define CONFIG_HAS_FSL_DR_USB 289 #ifdef CONFIG_HAS_FSL_DR_USB 290 #define CONFIG_USB_EHCI 291 292 #ifdef CONFIG_USB_EHCI 293 #define CONFIG_CMD_USB 294 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 295 #define CONFIG_USB_EHCI_FSL 296 #define CONFIG_USB_STORAGE 297 #define CONFIG_CMD_FAT 298 #define CONFIG_CMD_EXT2 299 #define CONFIG_CMD_FAT 300 #define CONFIG_DOS_PARTITION 301 #endif 302 #endif 303 304 /* 305 * Miscellaneous configurable options 306 */ 307 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 308 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 309 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 310 #if defined(CONFIG_CMD_KGDB) 311 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 312 #else 313 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 314 #endif 315 /* Print Buffer Size */ 316 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) 317 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 318 /* Boot Argument Buffer Size */ 319 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 320 321 /* 322 * For booting Linux, the board info and command line data 323 * have to be in the first 64 MB of memory, since this is 324 * the maximum mapped by the Linux kernel during initialization. 325 */ 326 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 327 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 328 329 /* 330 * Environment Configuration 331 */ 332 #define CONFIG_BOOTFILE "uImage" 333 #define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */ 334 335 /* default location for tftp and bootm */ 336 #define CONFIG_LOADADDR 1000000 337 338 #define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ 339 340 #define CONFIG_BAUDRATE 115200 341 342 /* Qman/Bman */ 343 #define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */ 344 #define CONFIG_SYS_QMAN_MEM_BASE 0xff000000 345 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 346 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 347 #define CONFIG_SYS_BMAN_MEM_BASE 0xff200000 348 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 349 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 350 351 /* For FM */ 352 #define CONFIG_SYS_DPAA_FMAN 353 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 354 355 #ifdef CONFIG_SYS_DPAA_FMAN 356 #define CONFIG_FMAN_ENET 357 #define CONFIG_PHY_ATHEROS 358 #endif 359 360 /* Default address of microcode for the Linux Fman driver */ 361 /* QE microcode/firmware address */ 362 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 363 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 364 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 365 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 366 367 #ifdef CONFIG_FMAN_ENET 368 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1 369 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2 370 371 #define CONFIG_SYS_TBIPA_VALUE 8 372 #define CONFIG_MII /* MII PHY management */ 373 #define CONFIG_ETHPRIME "FM1@DTSEC1" 374 #endif 375 376 #define CONFIG_EXTRA_ENV_SETTINGS \ 377 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" 378 379 #endif /* __CONFIG_H */ 380