1 /* 2 * Copyright 2013 Freescale Semiconductor, Inc. 3 * 4 * Authors: Roy Zang <tie-fei.zang@freescale.com> 5 * Chunhe Lan <Chunhe.Lan@freescale.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #ifndef CONFIG_SYS_MONITOR_BASE 14 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 15 #endif 16 17 #ifndef CONFIG_RESET_VECTOR_ADDRESS 18 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 19 #endif 20 21 /* High Level Configuration Options */ 22 #define CONFIG_MP /* support multiple processors */ 23 24 #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ 25 #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ 26 #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ 27 #define CONFIG_PCIE3 /* PCIE controller 3 (slot 3) */ 28 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 29 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 30 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 31 32 #ifndef __ASSEMBLY__ 33 extern unsigned long get_clock_freq(void); 34 #endif 35 36 #define CONFIG_SYS_CLK_FREQ 66666666 37 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 38 39 /* 40 * These can be toggled for performance analysis, otherwise use default. 41 */ 42 #define CONFIG_L2_CACHE /* toggle L2 cache */ 43 #define CONFIG_BTB /* toggle branch predition */ 44 #define CONFIG_HWCONFIG 45 46 #define CONFIG_ENABLE_36BIT_PHYS 47 48 #define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ 49 #define CONFIG_SYS_MEMTEST_END 0x02000000 50 51 /* Implement conversion of addresses in the LBC */ 52 #define CONFIG_SYS_LBC_LBCR 0x00000000 53 #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 54 55 /* DDR Setup */ 56 #define CONFIG_VERY_BIG_RAM 57 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 58 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 59 60 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 61 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 62 63 #define CONFIG_DDR_SPD 64 #define CONFIG_FSL_DDR_INTERACTIVE 65 #define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */ 66 #define CONFIG_SYS_SPD_BUS_NUM 0 67 #define SPD_EEPROM_ADDRESS 0x50 68 #define CONFIG_SYS_DDR_RAW_TIMING 69 70 /* 71 * Memory map 72 * 73 * 0x0000_0000 0x1fff_ffff DDR 512M cacheable 74 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable 75 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable 76 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable 77 * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable 78 * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable 79 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0 80 * 81 * Localbus non-cacheable 82 * 83 * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable 84 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable 85 */ 86 87 /* 88 * Local Bus Definitions 89 */ 90 #define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */ 91 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 92 93 #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 94 | BR_PS_16 | BR_V) 95 #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 96 97 #define CONFIG_FLASH_CFI_DRIVER 98 #define CONFIG_SYS_FLASH_CFI 99 #define CONFIG_SYS_FLASH_EMPTY_INFO 100 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 101 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 102 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 103 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 104 105 #define CONFIG_SYS_INIT_RAM_LOCK 106 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 107 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */ 108 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 109 GENERATED_GBL_DATA_SIZE) 110 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 111 112 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */ 113 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ 114 115 #define CONFIG_SYS_NAND_BASE 0xffa00000 116 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 117 118 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 119 #define CONFIG_SYS_MAX_NAND_DEVICE 1 120 #define CONFIG_NAND_FSL_ELBC 121 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 122 123 /* NAND flash config */ 124 #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 125 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 126 | BR_PS_8 /* Port Size = 8bit */ \ 127 | BR_MS_FCM /* MSEL = FCM */ \ 128 | BR_V) /* valid */ 129 #define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ 130 | OR_FCM_PGS \ 131 | OR_FCM_CSCT \ 132 | OR_FCM_CST \ 133 | OR_FCM_CHT \ 134 | OR_FCM_SCY_1 \ 135 | OR_FCM_TRLX \ 136 | OR_FCM_EHTR) 137 138 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 139 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 140 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 141 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 142 143 /* Serial Port */ 144 #undef CONFIG_SERIAL_SOFTWARE_FIFO 145 #define CONFIG_SYS_NS16550_SERIAL 146 #define CONFIG_SYS_NS16550_REG_SIZE 1 147 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 148 149 #define CONFIG_SYS_BAUDRATE_TABLE \ 150 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 151 152 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 153 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 154 155 /* I2C */ 156 #define CONFIG_SYS_I2C 157 #define CONFIG_SYS_I2C_FSL 158 #define CONFIG_SYS_FSL_I2C_SPEED 400000 159 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 160 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 161 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 162 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 163 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 164 165 /* 166 * I2C2 EEPROM 167 */ 168 #define CONFIG_ID_EEPROM 169 #ifdef CONFIG_ID_EEPROM 170 #define CONFIG_SYS_I2C_EEPROM_NXID 171 #endif 172 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 173 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 174 #define CONFIG_SYS_EEPROM_BUS_NUM 0 175 176 /* 177 * General PCI 178 * Memory space is mapped 1-1, but I/O space must start from 0. 179 */ 180 181 /* controller 3, Slot 1, tgtid 3, Base address b000 */ 182 #define CONFIG_SYS_PCIE3_NAME "Slot 3" 183 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 184 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 185 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 186 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 187 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 188 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 189 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 190 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 191 192 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 193 #define CONFIG_SYS_PCIE2_NAME "Slot 2" 194 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 195 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 196 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 197 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 198 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 199 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 200 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 201 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 202 203 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 204 #define CONFIG_SYS_PCIE1_NAME "Slot 1" 205 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 206 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 207 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 208 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 209 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 210 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 211 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 212 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 213 214 #if defined(CONFIG_PCI) 215 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 216 #endif /* CONFIG_PCI */ 217 218 /* 219 * Environment 220 */ 221 #define CONFIG_ENV_OVERWRITE 222 223 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 224 #define CONFIG_ENV_SIZE 0x2000 225 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 226 227 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 228 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 229 230 /* 231 * USB 232 */ 233 #define CONFIG_HAS_FSL_DR_USB 234 #ifdef CONFIG_HAS_FSL_DR_USB 235 #ifdef CONFIG_USB_EHCI_HCD 236 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 237 #define CONFIG_USB_EHCI_FSL 238 #endif 239 #endif 240 241 /* 242 * Miscellaneous configurable options 243 */ 244 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 245 246 /* 247 * For booting Linux, the board info and command line data 248 * have to be in the first 64 MB of memory, since this is 249 * the maximum mapped by the Linux kernel during initialization. 250 */ 251 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 252 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 253 254 /* 255 * Environment Configuration 256 */ 257 #define CONFIG_BOOTFILE "uImage" 258 #define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */ 259 260 /* default location for tftp and bootm */ 261 #define CONFIG_LOADADDR 1000000 262 263 /* Qman/Bman */ 264 #define CONFIG_SYS_QMAN_MEM_BASE 0xff000000 265 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 266 #define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 267 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 268 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 269 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 270 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 271 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 272 CONFIG_SYS_QMAN_CENA_SIZE) 273 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 274 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 275 #define CONFIG_SYS_BMAN_MEM_BASE 0xff200000 276 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 277 #define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 278 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 279 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 280 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 281 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 282 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 283 CONFIG_SYS_BMAN_CENA_SIZE) 284 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 285 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 286 287 /* For FM */ 288 #define CONFIG_SYS_DPAA_FMAN 289 290 #ifdef CONFIG_SYS_DPAA_FMAN 291 #define CONFIG_FMAN_ENET 292 #define CONFIG_PHY_ATHEROS 293 #endif 294 295 /* Default address of microcode for the Linux Fman driver */ 296 /* QE microcode/firmware address */ 297 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 298 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 299 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 300 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 301 302 #ifdef CONFIG_FMAN_ENET 303 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1 304 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2 305 306 #define CONFIG_SYS_TBIPA_VALUE 8 307 #define CONFIG_MII /* MII PHY management */ 308 #define CONFIG_ETHPRIME "FM1@DTSEC1" 309 #endif 310 311 #define CONFIG_EXTRA_ENV_SETTINGS \ 312 "netdev=eth0\0" \ 313 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 314 "loadaddr=1000000\0" \ 315 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 316 "tftpflash=tftpboot $loadaddr $uboot; " \ 317 "protect off $ubootaddr +$filesize; " \ 318 "erase $ubootaddr +$filesize; " \ 319 "cp.b $loadaddr $ubootaddr $filesize; " \ 320 "protect on $ubootaddr +$filesize; " \ 321 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 322 "consoledev=ttyS0\0" \ 323 "ramdiskaddr=2000000\0" \ 324 "ramdiskfile=rootfs.ext2.gz.uboot\0" \ 325 "fdtaddr=1e00000\0" \ 326 "fdtfile=p1023rdb.dtb\0" \ 327 "othbootargs=ramdisk_size=600000\0" \ 328 "bdev=sda1\0" \ 329 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" 330 331 #define CONFIG_HDBOOT \ 332 "setenv bootargs root=/dev/$bdev rw " \ 333 "console=$consoledev,$baudrate $othbootargs;" \ 334 "tftp $loadaddr $bootfile;" \ 335 "tftp $fdtaddr $fdtfile;" \ 336 "bootm $loadaddr - $fdtaddr" 337 338 #define CONFIG_NFSBOOTCOMMAND \ 339 "setenv bootargs root=/dev/nfs rw " \ 340 "nfsroot=$serverip:$rootpath " \ 341 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 342 "console=$consoledev,$baudrate $othbootargs;" \ 343 "tftp $loadaddr $bootfile;" \ 344 "tftp $fdtaddr $fdtfile;" \ 345 "bootm $loadaddr - $fdtaddr" 346 347 #define CONFIG_RAMBOOTCOMMAND \ 348 "setenv bootargs root=/dev/ram rw " \ 349 "console=$consoledev,$baudrate $othbootargs;" \ 350 "tftp $ramdiskaddr $ramdiskfile;" \ 351 "tftp $loadaddr $bootfile;" \ 352 "tftp $fdtaddr $fdtfile;" \ 353 "bootm $loadaddr $ramdiskaddr $fdtaddr" 354 355 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 356 357 #endif /* __CONFIG_H */ 358