1 /* 2 * Copyright 2010 Freescale Semiconductor, Inc. 3 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> 4 * Timur Tabi <timur@freescale.com> 5 * 6 * This program is free software; you can redistribute it and/or modify it 7 * under the terms of the GNU General Public License as published by the Free 8 * Software Foundation; either version 2 of the License, or (at your option) 9 * any later version. 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 #include "../board/freescale/common/ics307_clk.h" 16 17 /* High Level Configuration Options */ 18 #define CONFIG_BOOKE /* BOOKE */ 19 #define CONFIG_E500 /* BOOKE e500 family */ 20 #define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */ 21 #define CONFIG_P1022 22 #define CONFIG_P1022DS 23 #define CONFIG_MP /* support multiple processors */ 24 25 #ifndef CONFIG_SYS_TEXT_BASE 26 #define CONFIG_SYS_TEXT_BASE 0xeff80000 27 #endif 28 29 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 30 #define CONFIG_PCI /* Enable PCI/PCIE */ 31 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 32 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ 33 #define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */ 34 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 35 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 36 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 37 #define CONFIG_SYS_HAS_SERDES /* has SERDES */ 38 39 #define CONFIG_PHYS_64BIT 40 #define CONFIG_ENABLE_36BIT_PHYS 41 #define CONFIG_ADDR_MAP 42 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 43 44 #define CONFIG_FSL_LAW /* Use common FSL init code */ 45 46 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 47 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 48 #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ 49 50 /* 51 * These can be toggled for performance analysis, otherwise use default. 52 */ 53 #define CONFIG_L2_CACHE 54 #define CONFIG_BTB 55 56 #define CONFIG_SYS_MEMTEST_START 0x00000000 57 #define CONFIG_SYS_MEMTEST_END 0x7fffffff 58 59 /* 60 * Base addresses -- Note these are effective addresses where the 61 * actual resources get mapped (not physical addresses) 62 */ 63 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 64 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 65 #define CONFIG_SYS_CCSRBAR_PHYS 0xfffe00000ull 66 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR 67 68 /* DDR Setup */ 69 #define CONFIG_DDR_SPD 70 #define CONFIG_VERY_BIG_RAM 71 #define CONFIG_FSL_DDR3 72 73 #ifdef CONFIG_DDR_ECC 74 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 75 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 76 #endif 77 78 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 79 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 80 81 #define CONFIG_NUM_DDR_CONTROLLERS 1 82 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 83 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 84 85 /* I2C addresses of SPD EEPROMs */ 86 #define CONFIG_SYS_SPD_BUS_NUM 1 87 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 88 89 /* 90 * Memory map 91 * 92 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 93 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable 94 * 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable 95 * 96 * Localbus cacheable (TBD) 97 * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable 98 * 99 * Localbus non-cacheable 100 * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable 101 * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable 102 * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 103 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 104 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 105 */ 106 107 /* 108 * Local Bus Definitions 109 */ 110 #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ 111 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 112 113 #define CONFIG_FLASH_BR_PRELIM \ 114 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) 115 #define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7) 116 117 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 118 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 119 120 #define CONFIG_SYS_BR1_PRELIM \ 121 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) 122 #define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM 123 124 #define CONFIG_SYS_FLASH_BANKS_LIST \ 125 {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 126 #define CONFIG_SYS_FLASH_QUIET_TEST 127 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 128 129 #define CONFIG_SYS_MAX_FLASH_BANKS 2 130 #define CONFIG_SYS_MAX_FLASH_SECT 1024 131 132 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 133 134 #define CONFIG_FLASH_CFI_DRIVER 135 #define CONFIG_SYS_FLASH_CFI 136 #define CONFIG_SYS_FLASH_EMPTY_INFO 137 138 #define CONFIG_BOARD_EARLY_INIT_F 139 #define CONFIG_BOARD_EARLY_INIT_R 140 #define CONFIG_MISC_INIT_R 141 #define CONFIG_HWCONFIG 142 143 #define CONFIG_FSL_NGPIXIS 144 #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ 145 #define PIXIS_BASE_PHYS 0xfffdf0000ull 146 147 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) 148 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7) 149 150 #define PIXIS_LBMAP_SWITCH 7 151 #define PIXIS_LBMAP_MASK 0xE0 152 #define PIXIS_LBMAP_ALTBANK 0x20 153 154 #define CONFIG_SYS_INIT_RAM_LOCK 155 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 156 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ 157 158 #define CONFIG_SYS_GBL_DATA_OFFSET \ 159 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 160 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 161 162 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 163 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) 164 165 /* 166 * Serial Port 167 */ 168 #define CONFIG_CONS_INDEX 1 169 #define CONFIG_SYS_NS16550 170 #define CONFIG_SYS_NS16550_SERIAL 171 #define CONFIG_SYS_NS16550_REG_SIZE 1 172 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 173 174 #define CONFIG_SYS_BAUDRATE_TABLE \ 175 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 176 177 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 178 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 179 180 /* Use the HUSH parser */ 181 #define CONFIG_SYS_HUSH_PARSER 182 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 183 184 /* Video */ 185 #undef CONFIG_FSL_DIU_FB 186 187 #ifdef CONFIG_FSL_DIU_FB 188 #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) 189 #define CONFIG_VIDEO 190 #define CONFIG_CMD_BMP 191 #define CONFIG_CFB_CONSOLE 192 #define CONFIG_VGA_AS_SINGLE_DEVICE 193 #define CONFIG_VIDEO_LOGO 194 #define CONFIG_VIDEO_BMP_LOGO 195 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 196 /* 197 * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so 198 * disable empty flash sector detection, which is I/O-intensive. 199 */ 200 #undef CONFIG_SYS_FLASH_EMPTY_INFO 201 #endif 202 203 /* 204 * Pass open firmware flat tree 205 */ 206 #define CONFIG_OF_LIBFDT 207 #define CONFIG_OF_BOARD_SETUP 208 #define CONFIG_OF_STDOUT_VIA_ALIAS 209 210 /* new uImage format support */ 211 #define CONFIG_FIT 212 #define CONFIG_FIT_VERBOSE 213 214 /* I2C */ 215 #define CONFIG_FSL_I2C 216 #define CONFIG_HARD_I2C 217 #define CONFIG_I2C_MULTI_BUS 218 #define CONFIG_SYS_I2C_SPEED 400000 219 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 220 #define CONFIG_SYS_I2C_SLAVE 0x7F 221 #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} 222 #define CONFIG_SYS_I2C_OFFSET 0x3000 223 #define CONFIG_SYS_I2C2_OFFSET 0x3100 224 225 /* 226 * I2C2 EEPROM 227 */ 228 #define CONFIG_ID_EEPROM 229 #define CONFIG_SYS_I2C_EEPROM_NXID 230 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 231 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 232 #define CONFIG_SYS_EEPROM_BUS_NUM 1 233 234 /* 235 * General PCI 236 * Memory space is mapped 1-1, but I/O space must start from 0. 237 */ 238 239 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 240 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 241 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 242 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull 243 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 244 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 245 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 246 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull 247 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 248 249 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 250 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 251 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 252 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 253 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 254 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 255 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 256 #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull 257 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 258 259 /* controller 3, Slot 1, tgtid 3, Base address b000 */ 260 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 261 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 262 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull 263 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 264 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 265 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 266 #define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull 267 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 268 269 #ifdef CONFIG_PCI 270 #define CONFIG_NET_MULTI 271 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 272 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 273 #define CONFIG_E1000 /* Define e1000 pci Ethernet card */ 274 #endif 275 276 /* SATA */ 277 #define CONFIG_LIBATA 278 #define CONFIG_FSL_SATA 279 280 #define CONFIG_SYS_SATA_MAX_DEVICE 2 281 #define CONFIG_SATA1 282 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 283 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 284 #define CONFIG_SATA2 285 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 286 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 287 288 #ifdef CONFIG_FSL_SATA 289 #define CONFIG_LBA48 290 #define CONFIG_CMD_SATA 291 #define CONFIG_DOS_PARTITION 292 #define CONFIG_CMD_EXT2 293 #endif 294 295 #define CONFIG_MMC 296 #ifdef CONFIG_MMC 297 #define CONFIG_CMD_MMC 298 #define CONFIG_FSL_ESDHC 299 #define CONFIG_GENERIC_MMC 300 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 301 #endif 302 303 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) 304 #define CONFIG_CMD_EXT2 305 #define CONFIG_CMD_FAT 306 #define CONFIG_DOS_PARTITION 307 #endif 308 309 #define CONFIG_TSEC_ENET 310 #ifdef CONFIG_TSEC_ENET 311 312 #define CONFIG_TSECV2 313 #define CONFIG_NET_MULTI 314 315 #define CONFIG_MII /* MII PHY management */ 316 #define CONFIG_TSEC1 1 317 #define CONFIG_TSEC1_NAME "eTSEC1" 318 #define CONFIG_TSEC2 1 319 #define CONFIG_TSEC2_NAME "eTSEC2" 320 321 #define TSEC1_PHY_ADDR 1 322 #define TSEC2_PHY_ADDR 2 323 324 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 325 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 326 327 #define TSEC1_PHYIDX 0 328 #define TSEC2_PHYIDX 0 329 330 #define CONFIG_ETHPRIME "eTSEC1" 331 332 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 333 #endif 334 335 /* 336 * Environment 337 */ 338 #define CONFIG_ENV_IS_IN_FLASH 339 #define CONFIG_ENV_OVERWRITE 340 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 341 #define CONFIG_ENV_SIZE 0x2000 342 #define CONFIG_ENV_SECT_SIZE 0x20000 343 344 #define CONFIG_LOADS_ECHO 345 #define CONFIG_SYS_LOADS_BAUD_CHANGE 346 347 /* 348 * Command line configuration. 349 */ 350 #include <config_cmd_default.h> 351 352 #define CONFIG_CMD_ELF 353 #define CONFIG_CMD_ERRATA 354 #define CONFIG_CMD_IRQ 355 #define CONFIG_CMD_I2C 356 #define CONFIG_CMD_MII 357 #define CONFIG_CMD_PING 358 #define CONFIG_CMD_SETEXPR 359 360 #ifdef CONFIG_PCI 361 #define CONFIG_CMD_PCI 362 #define CONFIG_CMD_NET 363 #endif 364 365 /* 366 * USB 367 */ 368 #define CONFIG_USB_EHCI 369 370 #ifdef CONFIG_USB_EHCI 371 #define CONFIG_CMD_USB 372 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 373 #define CONFIG_USB_EHCI_FSL 374 #define CONFIG_USB_STORAGE 375 #define CONFIG_CMD_FAT 376 #endif 377 378 /* 379 * Miscellaneous configurable options 380 */ 381 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 382 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 383 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 384 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 385 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 386 #ifdef CONFIG_CMD_KGDB 387 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 388 #else 389 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 390 #endif 391 /* Print Buffer Size */ 392 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 393 #define CONFIG_SYS_MAXARGS 16 394 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 395 #define CONFIG_SYS_HZ 1000 396 397 /* 398 * For booting Linux, the board info and command line data 399 * have to be in the first 16 MB of memory, since this is 400 * the maximum mapped by the Linux kernel during initialization. 401 */ 402 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 403 404 #ifdef CONFIG_CMD_KGDB 405 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 406 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 407 #endif 408 409 /* 410 * Environment Configuration 411 */ 412 413 #define CONFIG_HOSTNAME p1022ds 414 #define CONFIG_ROOTPATH /opt/nfsroot 415 #define CONFIG_BOOTFILE uImage 416 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 417 418 #define CONFIG_LOADADDR 1000000 419 420 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 421 #define CONFIG_BOOTARGS 422 423 #define CONFIG_BAUDRATE 115200 424 425 #define CONFIG_EXTRA_ENV_SETTINGS \ 426 "perf_mode=stable\0" \ 427 "memctl_intlv_ctl=2\0" \ 428 "netdev=eth0\0" \ 429 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ 430 "tftpflash=tftpboot $loadaddr $uboot; " \ 431 "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 432 "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 433 "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \ 434 "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 435 "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ 436 "consoledev=ttyS0\0" \ 437 "ramdiskaddr=2000000\0" \ 438 "ramdiskfile=uramdisk\0" \ 439 "fdtaddr=c00000\0" \ 440 "fdtfile=p1022ds.dtb\0" \ 441 "bdev=sda3\0" \ 442 "diuregs=md e002c000 1d\0" \ 443 "dium=mw e002c01c\0" \ 444 "diuerr=md e002c014 1\0" \ 445 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \ 446 "monitor=0-DVI\0" 447 448 #define CONFIG_HDBOOT \ 449 "setenv bootargs root=/dev/$bdev rw " \ 450 "console=$consoledev,$baudrate $othbootargs;" \ 451 "tftp $loadaddr $bootfile;" \ 452 "tftp $fdtaddr $fdtfile;" \ 453 "bootm $loadaddr - $fdtaddr" 454 455 #define CONFIG_NFSBOOTCOMMAND \ 456 "setenv bootargs root=/dev/nfs rw " \ 457 "nfsroot=$serverip:$rootpath " \ 458 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 459 "console=$consoledev,$baudrate $othbootargs;" \ 460 "tftp $loadaddr $bootfile;" \ 461 "tftp $fdtaddr $fdtfile;" \ 462 "bootm $loadaddr - $fdtaddr" 463 464 #define CONFIG_RAMBOOTCOMMAND \ 465 "setenv bootargs root=/dev/ram rw " \ 466 "console=$consoledev,$baudrate $othbootargs;" \ 467 "tftp $ramdiskaddr $ramdiskfile;" \ 468 "tftp $loadaddr $bootfile;" \ 469 "tftp $fdtaddr $fdtfile;" \ 470 "bootm $loadaddr $ramdiskaddr $fdtaddr" 471 472 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 473 474 #endif 475