1 /* 2 * Copyright 2010-2011 Freescale Semiconductor, Inc. 3 * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com> 4 * Timur Tabi <timur@freescale.com> 5 * 6 * This program is free software; you can redistribute it and/or modify it 7 * under the terms of the GNU General Public License as published by the Free 8 * Software Foundation; either version 2 of the License, or (at your option) 9 * any later version. 10 */ 11 12 #ifndef __CONFIG_H 13 #define __CONFIG_H 14 15 #include "../board/freescale/common/ics307_clk.h" 16 17 #ifdef CONFIG_36BIT 18 #define CONFIG_PHYS_64BIT 19 #endif 20 21 /* High Level Configuration Options */ 22 #define CONFIG_BOOKE /* BOOKE */ 23 #define CONFIG_E500 /* BOOKE e500 family */ 24 #define CONFIG_MPC85xx /* MPC8540/60/55/41/48 */ 25 #define CONFIG_P1022 26 #define CONFIG_P1022DS 27 #define CONFIG_MP /* support multiple processors */ 28 29 #ifndef CONFIG_SYS_TEXT_BASE 30 #define CONFIG_SYS_TEXT_BASE 0xeff80000 31 #endif 32 33 #ifndef CONFIG_RESET_VECTOR_ADDRESS 34 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 35 #endif 36 37 #define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ 38 #define CONFIG_PCI /* Enable PCI/PCIE */ 39 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 40 #define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ 41 #define CONFIG_PCIE3 /* PCIE controler 3 (ULI bridge) */ 42 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 43 #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ 44 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 45 46 #define CONFIG_ENABLE_36BIT_PHYS 47 48 #ifdef CONFIG_PHYS_64BIT 49 #define CONFIG_ADDR_MAP 50 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 51 #endif 52 53 #define CONFIG_FSL_LAW /* Use common FSL init code */ 54 55 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 56 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 57 #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ 58 59 /* 60 * These can be toggled for performance analysis, otherwise use default. 61 */ 62 #define CONFIG_L2_CACHE 63 #define CONFIG_BTB 64 65 #define CONFIG_SYS_MEMTEST_START 0x00000000 66 #define CONFIG_SYS_MEMTEST_END 0x7fffffff 67 68 #define CONFIG_SYS_CCSRBAR 0xffe00000 69 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 70 71 /* DDR Setup */ 72 #define CONFIG_DDR_SPD 73 #define CONFIG_VERY_BIG_RAM 74 #define CONFIG_FSL_DDR3 75 76 #ifdef CONFIG_DDR_ECC 77 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 78 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 79 #endif 80 81 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 82 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 83 84 #define CONFIG_NUM_DDR_CONTROLLERS 1 85 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 86 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 87 88 /* I2C addresses of SPD EEPROMs */ 89 #define CONFIG_SYS_SPD_BUS_NUM 1 90 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 91 92 /* 93 * Memory map 94 * 95 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 96 * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable 97 * 0xffc0_0000 0xffc2_ffff PCI IO range 192K non-cacheable 98 * 99 * Localbus cacheable (TBD) 100 * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable 101 * 102 * Localbus non-cacheable 103 * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable 104 * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable 105 * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 106 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 107 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 108 */ 109 110 /* 111 * Local Bus Definitions 112 */ 113 #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ 114 #ifdef CONFIG_PHYS_64BIT 115 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 116 #else 117 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 118 #endif 119 120 #define CONFIG_FLASH_BR_PRELIM \ 121 (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V) 122 #define CONFIG_FLASH_OR_PRELIM (OR_AM_128MB | 0xff7) 123 124 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 125 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 126 127 #define CONFIG_SYS_BR1_PRELIM \ 128 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) 129 #define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM 130 131 #define CONFIG_SYS_FLASH_BANKS_LIST \ 132 {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 133 #define CONFIG_SYS_FLASH_QUIET_TEST 134 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 135 136 #define CONFIG_SYS_MAX_FLASH_BANKS 2 137 #define CONFIG_SYS_MAX_FLASH_SECT 1024 138 139 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 140 141 #define CONFIG_FLASH_CFI_DRIVER 142 #define CONFIG_SYS_FLASH_CFI 143 #define CONFIG_SYS_FLASH_EMPTY_INFO 144 145 #define CONFIG_BOARD_EARLY_INIT_F 146 #define CONFIG_BOARD_EARLY_INIT_R 147 #define CONFIG_MISC_INIT_R 148 #define CONFIG_HWCONFIG 149 150 #define CONFIG_FSL_NGPIXIS 151 #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ 152 #ifdef CONFIG_PHYS_64BIT 153 #define PIXIS_BASE_PHYS 0xfffdf0000ull 154 #else 155 #define PIXIS_BASE_PHYS PIXIS_BASE 156 #endif 157 158 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) 159 #define CONFIG_SYS_OR2_PRELIM (OR_AM_32KB | 0x6ff7) 160 161 #define PIXIS_LBMAP_SWITCH 7 162 #define PIXIS_LBMAP_MASK 0xF0 163 #define PIXIS_LBMAP_ALTBANK 0x20 164 #define PIXIS_ELBC_SPI_MASK 0xc0 165 #define PIXIS_SPI 0x80 166 167 #define CONFIG_SYS_INIT_RAM_LOCK 168 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 169 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ 170 171 #define CONFIG_SYS_GBL_DATA_OFFSET \ 172 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 173 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 174 175 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) 176 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) 177 178 /* 179 * Serial Port 180 */ 181 #define CONFIG_CONS_INDEX 1 182 #define CONFIG_SYS_NS16550 183 #define CONFIG_SYS_NS16550_SERIAL 184 #define CONFIG_SYS_NS16550_REG_SIZE 1 185 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 186 187 #define CONFIG_SYS_BAUDRATE_TABLE \ 188 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 189 190 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 191 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 192 193 /* Use the HUSH parser */ 194 #define CONFIG_SYS_HUSH_PARSER 195 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 196 197 /* Video */ 198 #define CONFIG_FSL_DIU_FB 199 200 #ifdef CONFIG_FSL_DIU_FB 201 #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x10000) 202 #define CONFIG_VIDEO 203 #define CONFIG_CMD_BMP 204 #define CONFIG_CFB_CONSOLE 205 #define CONFIG_VIDEO_SW_CURSOR 206 #define CONFIG_VGA_AS_SINGLE_DEVICE 207 #define CONFIG_VIDEO_LOGO 208 #define CONFIG_VIDEO_BMP_LOGO 209 #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 210 /* 211 * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so 212 * disable empty flash sector detection, which is I/O-intensive. 213 */ 214 #undef CONFIG_SYS_FLASH_EMPTY_INFO 215 #endif 216 217 #ifndef CONFIG_FSL_DIU_FB 218 #define CONFIG_ATI 219 #endif 220 221 #ifdef CONFIG_ATI 222 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT 223 #define CONFIG_VIDEO 224 #define CONFIG_BIOSEMU 225 #define CONFIG_VIDEO_SW_CURSOR 226 #define CONFIG_ATI_RADEON_FB 227 #define CONFIG_VIDEO_LOGO 228 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET 229 #define CONFIG_CFB_CONSOLE 230 #define CONFIG_VGA_AS_SINGLE_DEVICE 231 #endif 232 233 /* 234 * Pass open firmware flat tree 235 */ 236 #define CONFIG_OF_LIBFDT 237 #define CONFIG_OF_BOARD_SETUP 238 #define CONFIG_OF_STDOUT_VIA_ALIAS 239 240 /* new uImage format support */ 241 #define CONFIG_FIT 242 #define CONFIG_FIT_VERBOSE 243 244 /* I2C */ 245 #define CONFIG_FSL_I2C 246 #define CONFIG_HARD_I2C 247 #define CONFIG_I2C_MULTI_BUS 248 #define CONFIG_SYS_I2C_SPEED 400000 249 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 250 #define CONFIG_SYS_I2C_SLAVE 0x7F 251 #define CONFIG_SYS_I2C_NOPROBES {{0, 0x29}} 252 #define CONFIG_SYS_I2C_OFFSET 0x3000 253 #define CONFIG_SYS_I2C2_OFFSET 0x3100 254 255 /* 256 * I2C2 EEPROM 257 */ 258 #define CONFIG_ID_EEPROM 259 #define CONFIG_SYS_I2C_EEPROM_NXID 260 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 261 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 262 #define CONFIG_SYS_EEPROM_BUS_NUM 1 263 264 /* 265 * eSPI - Enhanced SPI 266 */ 267 #define CONFIG_SPI_FLASH 268 #define CONFIG_SPI_FLASH_SPANSION 269 270 #define CONFIG_HARD_SPI 271 #define CONFIG_FSL_ESPI 272 273 #define CONFIG_CMD_SF 274 #define CONFIG_SF_DEFAULT_SPEED 10000000 275 #define CONFIG_SF_DEFAULT_MODE 0 276 277 /* 278 * General PCI 279 * Memory space is mapped 1-1, but I/O space must start from 0. 280 */ 281 282 /* controller 1, Slot 2, tgtid 1, Base address a000 */ 283 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 284 #ifdef CONFIG_PHYS_64BIT 285 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 286 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull 287 #else 288 #define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 289 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 290 #endif 291 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 292 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 293 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 294 #ifdef CONFIG_PHYS_64BIT 295 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull 296 #else 297 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 298 #endif 299 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 300 301 /* controller 2, direct to uli, tgtid 2, Base address 9000 */ 302 #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 303 #ifdef CONFIG_PHYS_64BIT 304 #define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 305 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull 306 #else 307 #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 308 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 309 #endif 310 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 311 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 312 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 313 #ifdef CONFIG_PHYS_64BIT 314 #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull 315 #else 316 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 317 #endif 318 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 319 320 /* controller 3, Slot 1, tgtid 3, Base address b000 */ 321 #define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 322 #ifdef CONFIG_PHYS_64BIT 323 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 324 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull 325 #else 326 #define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 327 #define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 328 #endif 329 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 330 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 331 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 332 #ifdef CONFIG_PHYS_64BIT 333 #define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull 334 #else 335 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 336 #endif 337 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 338 339 #ifdef CONFIG_PCI 340 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 341 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 342 #define CONFIG_E1000 /* Define e1000 pci Ethernet card */ 343 #endif 344 345 /* SATA */ 346 #define CONFIG_LIBATA 347 #define CONFIG_FSL_SATA 348 #define CONFIG_FSL_SATA_V2 349 350 #define CONFIG_SYS_SATA_MAX_DEVICE 2 351 #define CONFIG_SATA1 352 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 353 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 354 #define CONFIG_SATA2 355 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 356 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 357 358 #ifdef CONFIG_FSL_SATA 359 #define CONFIG_LBA48 360 #define CONFIG_CMD_SATA 361 #define CONFIG_DOS_PARTITION 362 #define CONFIG_CMD_EXT2 363 #endif 364 365 #define CONFIG_MMC 366 #ifdef CONFIG_MMC 367 #define CONFIG_CMD_MMC 368 #define CONFIG_FSL_ESDHC 369 #define CONFIG_GENERIC_MMC 370 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 371 #endif 372 373 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) 374 #define CONFIG_CMD_EXT2 375 #define CONFIG_CMD_FAT 376 #define CONFIG_DOS_PARTITION 377 #endif 378 379 #define CONFIG_TSEC_ENET 380 #ifdef CONFIG_TSEC_ENET 381 382 #define CONFIG_TSECV2 383 384 #define CONFIG_MII /* MII PHY management */ 385 #define CONFIG_TSEC1 1 386 #define CONFIG_TSEC1_NAME "eTSEC1" 387 #define CONFIG_TSEC2 1 388 #define CONFIG_TSEC2_NAME "eTSEC2" 389 390 #define TSEC1_PHY_ADDR 1 391 #define TSEC2_PHY_ADDR 2 392 393 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 394 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 395 396 #define TSEC1_PHYIDX 0 397 #define TSEC2_PHYIDX 0 398 399 #define CONFIG_ETHPRIME "eTSEC1" 400 401 #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ 402 #endif 403 404 /* 405 * Environment 406 */ 407 #define CONFIG_ENV_IS_IN_FLASH 408 #define CONFIG_ENV_OVERWRITE 409 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 410 #define CONFIG_ENV_SIZE 0x2000 411 #define CONFIG_ENV_SECT_SIZE 0x20000 412 413 #define CONFIG_LOADS_ECHO 414 #define CONFIG_SYS_LOADS_BAUD_CHANGE 415 416 /* 417 * Command line configuration. 418 */ 419 #include <config_cmd_default.h> 420 421 #define CONFIG_CMD_ELF 422 #define CONFIG_CMD_ERRATA 423 #define CONFIG_CMD_IRQ 424 #define CONFIG_CMD_I2C 425 #define CONFIG_CMD_MII 426 #define CONFIG_CMD_PING 427 #define CONFIG_CMD_SETEXPR 428 #define CONFIG_CMD_REGINFO 429 430 #ifdef CONFIG_PCI 431 #define CONFIG_CMD_PCI 432 #define CONFIG_CMD_NET 433 #endif 434 435 /* 436 * USB 437 */ 438 #define CONFIG_USB_EHCI 439 440 #ifdef CONFIG_USB_EHCI 441 #define CONFIG_CMD_USB 442 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 443 #define CONFIG_USB_EHCI_FSL 444 #define CONFIG_USB_STORAGE 445 #define CONFIG_CMD_FAT 446 #endif 447 448 /* 449 * Miscellaneous configurable options 450 */ 451 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 452 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 453 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 454 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 455 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 456 #ifdef CONFIG_CMD_KGDB 457 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 458 #else 459 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 460 #endif 461 /* Print Buffer Size */ 462 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 463 #define CONFIG_SYS_MAXARGS 16 464 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 465 #define CONFIG_SYS_HZ 1000 466 467 /* 468 * For booting Linux, the board info and command line data 469 * have to be in the first 64 MB of memory, since this is 470 * the maximum mapped by the Linux kernel during initialization. 471 */ 472 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 473 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 474 475 #ifdef CONFIG_CMD_KGDB 476 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 477 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 478 #endif 479 480 /* 481 * Environment Configuration 482 */ 483 484 #define CONFIG_HOSTNAME p1022ds 485 #define CONFIG_ROOTPATH /opt/nfsroot 486 #define CONFIG_BOOTFILE uImage 487 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 488 489 #define CONFIG_LOADADDR 1000000 490 491 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 492 #define CONFIG_BOOTARGS 493 494 #define CONFIG_BAUDRATE 115200 495 496 #define CONFIG_EXTRA_ENV_SETTINGS \ 497 "perf_mode=stable\0" \ 498 "memctl_intlv_ctl=2\0" \ 499 "netdev=eth0\0" \ 500 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \ 501 "tftpflash=tftpboot $loadaddr $uboot; " \ 502 "protect off " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 503 "erase " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 504 "cp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize; " \ 505 "protect on " MK_STR(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ 506 "cmp.b $loadaddr " MK_STR(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ 507 "consoledev=ttyS0\0" \ 508 "ramdiskaddr=2000000\0" \ 509 "ramdiskfile=uramdisk\0" \ 510 "fdtaddr=c00000\0" \ 511 "fdtfile=p1022ds.dtb\0" \ 512 "bdev=sda3\0" \ 513 "diuregs=md e002c000 1d\0" \ 514 "dium=mw e002c01c\0" \ 515 "diuerr=md e002c014 1\0" \ 516 "hwconfig=esdhc;audclk:12\0" 517 518 #define CONFIG_HDBOOT \ 519 "setenv bootargs root=/dev/$bdev rw " \ 520 "console=$consoledev,$baudrate $othbootargs;" \ 521 "tftp $loadaddr $bootfile;" \ 522 "tftp $fdtaddr $fdtfile;" \ 523 "bootm $loadaddr - $fdtaddr" 524 525 #define CONFIG_NFSBOOTCOMMAND \ 526 "setenv bootargs root=/dev/nfs rw " \ 527 "nfsroot=$serverip:$rootpath " \ 528 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 529 "console=$consoledev,$baudrate $othbootargs;" \ 530 "tftp $loadaddr $bootfile;" \ 531 "tftp $fdtaddr $fdtfile;" \ 532 "bootm $loadaddr - $fdtaddr" 533 534 #define CONFIG_RAMBOOTCOMMAND \ 535 "setenv bootargs root=/dev/ram rw " \ 536 "console=$consoledev,$baudrate $othbootargs;" \ 537 "tftp $ramdiskaddr $ramdiskfile;" \ 538 "tftp $loadaddr $bootfile;" \ 539 "tftp $fdtaddr $fdtfile;" \ 540 "bootm $loadaddr $ramdiskaddr $fdtaddr" 541 542 #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND 543 544 #endif 545