1 /* 2 * Configuation settings for the Renesas Solutions Migo-R board 3 * 4 * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __MIGO_R_H 10 #define __MIGO_R_H 11 12 #define CONFIG_CPU_SH7722 1 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 #undef CONFIG_SHOW_BOOT_PROGRESS 16 17 /* SMC9111 */ 18 #define CONFIG_SMC91111 19 #define CONFIG_SMC91111_BASE (0xB0000000) 20 21 /* MEMORY */ 22 #define MIGO_R_SDRAM_BASE (0x8C000000) 23 #define MIGO_R_FLASH_BASE_1 (0xA0000000) 24 #define MIGO_R_FLASH_BANK_SIZE (64 * 1024 * 1024) 25 26 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 27 #define CONFIG_SYS_PBSIZE 256 /* Buffer size for Console output */ 28 #define CONFIG_SYS_BAUDRATE_TABLE { 115200 } /* List of legal baudrate settings for this board */ 29 30 /* SCIF */ 31 #define CONFIG_CONS_SCIF0 1 32 33 #define CONFIG_SYS_MEMTEST_START (MIGO_R_SDRAM_BASE) 34 #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024)) 35 36 /* Enable alternate, more extensive, memory test */ 37 #undef CONFIG_SYS_ALT_MEMTEST 38 /* Scratch address used by the alternate memory test */ 39 #undef CONFIG_SYS_MEMTEST_SCRATCH 40 41 /* Enable temporary baudrate change while serial download */ 42 #undef CONFIG_SYS_LOADS_BAUD_CHANGE 43 44 #define CONFIG_SYS_SDRAM_BASE (MIGO_R_SDRAM_BASE) 45 /* maybe more, but if so u-boot doesn't know about it... */ 46 #define CONFIG_SYS_SDRAM_SIZE (64 * 1024 * 1024) 47 /* default load address for scripts ?!? */ 48 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024) 49 50 /* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */ 51 #define CONFIG_SYS_MONITOR_BASE (MIGO_R_FLASH_BASE_1) 52 /* Monitor size */ 53 #define CONFIG_SYS_MONITOR_LEN (128 * 1024) 54 /* Size of DRAM reserved for malloc() use */ 55 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) 56 #define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) 57 58 /* FLASH */ 59 #define CONFIG_SYS_FLASH_CFI 60 #define CONFIG_FLASH_CFI_DRIVER 61 #undef CONFIG_SYS_FLASH_QUIET_TEST 62 /* print 'E' for empty sector on flinfo */ 63 #define CONFIG_SYS_FLASH_EMPTY_INFO 64 /* Physical start address of Flash memory */ 65 #define CONFIG_SYS_FLASH_BASE (MIGO_R_FLASH_BASE_1) 66 /* Max number of sectors on each Flash chip */ 67 #define CONFIG_SYS_MAX_FLASH_SECT 512 68 69 /* if you use all NOR Flash , you change dip-switch. Please see MIGO_R01 Manual. */ 70 #define CONFIG_SYS_MAX_FLASH_BANKS 1 71 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE + (0 * MIGO_R_FLASH_BANK_SIZE) } 72 73 /* Timeout for Flash erase operations (in ms) */ 74 #define CONFIG_SYS_FLASH_ERASE_TOUT (3 * 1000) 75 /* Timeout for Flash write operations (in ms) */ 76 #define CONFIG_SYS_FLASH_WRITE_TOUT (3 * 1000) 77 /* Timeout for Flash set sector lock bit operations (in ms) */ 78 #define CONFIG_SYS_FLASH_LOCK_TOUT (3 * 1000) 79 /* Timeout for Flash clear lock bit operations (in ms) */ 80 #define CONFIG_SYS_FLASH_UNLOCK_TOUT (3 * 1000) 81 82 /* Use hardware flash sectors protection instead of U-Boot software protection */ 83 #undef CONFIG_SYS_FLASH_PROTECTION 84 #undef CONFIG_SYS_DIRECT_FLASH_TFTP 85 86 /* ENV setting */ 87 #define CONFIG_ENV_OVERWRITE 1 88 #define CONFIG_ENV_SECT_SIZE (128 * 1024) 89 #define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) 90 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 91 /* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */ 92 #define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE) 93 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SECT_SIZE) 94 95 /* Board Clock */ 96 #define CONFIG_SYS_CLK_FREQ 33333333 97 #define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ 98 #define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ 99 #define CONFIG_SYS_TMU_CLK_DIV (4) /* 4 (default), 16, 64, 256 or 1024 */ 100 101 #endif /* __MIGO_R_H */ 102