1 /* 2 * Copyright 2006, 2010-2011 Freescale Semiconductor. 3 * 4 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * MPC8641HPCN board configuration file 11 * 12 * Make sure you change the MAC address and other network params first, 13 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. 14 */ 15 16 #ifndef __CONFIG_H 17 #define __CONFIG_H 18 19 #define CONFIG_SYS_GENERIC_BOARD 20 #define CONFIG_DISPLAY_BOARDINFO 21 22 /* High Level Configuration Options */ 23 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 24 #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ 25 #define CONFIG_MP 1 /* support multiple processors */ 26 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 27 /*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ 28 #define CONFIG_ADDR_MAP 1 /* Use addr map */ 29 30 /* 31 * default CCSRBAR is at 0xff700000 32 * assume U-Boot is less than 0.5MB 33 */ 34 #define CONFIG_SYS_TEXT_BASE 0xeff00000 35 36 #ifdef RUN_DIAG 37 #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE 38 #endif 39 40 /* 41 * virtual address to be used for temporary mappings. There 42 * should be 128k free at this VA. 43 */ 44 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 45 46 #define CONFIG_SYS_SRIO 47 #define CONFIG_SRIO1 /* SRIO port 1 */ 48 49 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 50 #define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ 51 #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ 52 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 53 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 54 #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ 55 56 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 57 #define CONFIG_ENV_OVERWRITE 58 59 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 60 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 61 #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ 62 63 #define CONFIG_ALTIVEC 1 64 65 /* 66 * L2CR setup -- make sure this is right for your board! 67 */ 68 #define CONFIG_SYS_L2 69 #define L2_INIT 0 70 #define L2_ENABLE (L2CR_L2E) 71 72 #ifndef CONFIG_SYS_CLK_FREQ 73 #ifndef __ASSEMBLY__ 74 extern unsigned long get_board_sys_clk(unsigned long dummy); 75 #endif 76 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 77 #endif 78 79 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 80 #define CONFIG_SYS_MEMTEST_END 0x00400000 81 82 /* 83 * With the exception of PCI Memory and Rapid IO, most devices will simply 84 * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA 85 * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. 86 */ 87 #ifdef CONFIG_PHYS_64BIT 88 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f 89 #else 90 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 91 #endif 92 93 /* 94 * Base addresses -- Note these are effective addresses where the 95 * actual resources get mapped (not physical addresses) 96 */ 97 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 98 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 99 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 100 101 /* Physical addresses */ 102 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 103 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH 104 #define CONFIG_SYS_CCSRBAR_PHYS \ 105 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 106 CONFIG_SYS_CCSRBAR_PHYS_HIGH) 107 108 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ 109 110 /* 111 * DDR Setup 112 */ 113 #define CONFIG_SYS_FSL_DDR2 114 #undef CONFIG_FSL_DDR_INTERACTIVE 115 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 116 #define CONFIG_DDR_SPD 117 118 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 119 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 120 121 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 122 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 123 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 124 #define CONFIG_VERY_BIG_RAM 125 126 #define CONFIG_NUM_DDR_CONTROLLERS 2 127 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 128 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 129 130 /* 131 * I2C addresses of SPD EEPROMs 132 */ 133 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 134 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ 135 #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ 136 #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ 137 138 139 /* 140 * These are used when DDR doesn't use SPD. 141 */ 142 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 143 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 144 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 145 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 146 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 147 #define CONFIG_SYS_DDR_TIMING_1 0x39357322 148 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 149 #define CONFIG_SYS_DDR_MODE_1 0x00480432 150 #define CONFIG_SYS_DDR_MODE_2 0x00000000 151 #define CONFIG_SYS_DDR_INTERVAL 0x06090100 152 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 153 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 154 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 155 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 156 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 157 #define CONFIG_SYS_DDR_CONTROL2 0x04400000 158 159 #define CONFIG_ID_EEPROM 160 #define CONFIG_SYS_I2C_EEPROM_NXID 161 #define CONFIG_ID_EEPROM 162 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 163 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 164 165 #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ 166 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE 167 #define CONFIG_SYS_FLASH_BASE_PHYS \ 168 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 169 CONFIG_SYS_PHYS_ADDR_HIGH) 170 171 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 172 173 #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 174 | 0x00001001) /* port size 16bit */ 175 #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ 176 177 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ 178 | 0x00001001) /* port size 16bit */ 179 #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ 180 181 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ 182 | 0x00000801) /* port size 8bit */ 183 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ 184 185 /* 186 * The LBC_BASE is the base of the region that contains the PIXIS and the CF. 187 * The PIXIS and CF by themselves aren't large enough to take up the 128k 188 * required for the smallest BAT mapping, so there's a 64k hole. 189 */ 190 #define CONFIG_SYS_LBC_BASE 0xffde0000 191 #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE 192 193 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 194 #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) 195 #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) 196 #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ 197 CONFIG_SYS_PHYS_ADDR_HIGH) 198 #define PIXIS_SIZE 0x00008000 /* 32k */ 199 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 200 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 201 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 202 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 203 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ 204 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 205 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 206 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 207 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 208 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 209 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 210 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 211 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 212 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 213 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 214 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 215 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 216 217 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ 218 #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) 219 #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) 220 221 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 222 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 223 224 #undef CONFIG_SYS_FLASH_CHECKSUM 225 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 226 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 227 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 228 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 229 230 #define CONFIG_FLASH_CFI_DRIVER 231 #define CONFIG_SYS_FLASH_CFI 232 #define CONFIG_SYS_FLASH_EMPTY_INFO 233 234 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 235 #define CONFIG_SYS_RAMBOOT 236 #else 237 #undef CONFIG_SYS_RAMBOOT 238 #endif 239 240 #if defined(CONFIG_SYS_RAMBOOT) 241 #undef CONFIG_SPD_EEPROM 242 #define CONFIG_SYS_SDRAM_SIZE 256 243 #endif 244 245 #undef CONFIG_CLOCKS_IN_MHZ 246 247 #define CONFIG_SYS_INIT_RAM_LOCK 1 248 #ifndef CONFIG_SYS_INIT_RAM_LOCK 249 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 250 #else 251 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 252 #endif 253 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 254 255 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 256 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 257 258 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 259 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 260 261 /* Serial Port */ 262 #define CONFIG_CONS_INDEX 1 263 #define CONFIG_SYS_NS16550 264 #define CONFIG_SYS_NS16550_SERIAL 265 #define CONFIG_SYS_NS16550_REG_SIZE 1 266 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 267 268 #define CONFIG_SYS_BAUDRATE_TABLE \ 269 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 270 271 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 272 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 273 274 /* Use the HUSH parser */ 275 #define CONFIG_SYS_HUSH_PARSER 276 277 /* 278 * Pass open firmware flat tree to kernel 279 */ 280 #define CONFIG_OF_LIBFDT 1 281 #define CONFIG_OF_BOARD_SETUP 1 282 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 283 284 /* 285 * I2C 286 */ 287 #define CONFIG_SYS_I2C 288 #define CONFIG_SYS_I2C_FSL 289 #define CONFIG_SYS_FSL_I2C_SPEED 400000 290 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 291 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 292 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 293 294 /* 295 * RapidIO MMU 296 */ 297 #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ 298 #ifdef CONFIG_PHYS_64BIT 299 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 300 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c 301 #else 302 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE 303 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 304 #endif 305 #define CONFIG_SYS_SRIO1_MEM_PHYS \ 306 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 307 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) 308 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 309 310 /* 311 * General PCI 312 * Addresses are mapped 1-1. 313 */ 314 315 #define CONFIG_SYS_PCIE1_NAME "ULI" 316 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 317 #ifdef CONFIG_PHYS_64BIT 318 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 319 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 320 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c 321 #else 322 #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT 323 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT 324 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 325 #endif 326 #define CONFIG_SYS_PCIE1_MEM_PHYS \ 327 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 328 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) 329 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 330 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 331 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 332 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT 333 #define CONFIG_SYS_PCIE1_IO_PHYS \ 334 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 335 CONFIG_SYS_PHYS_ADDR_HIGH) 336 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ 337 338 #ifdef CONFIG_PHYS_64BIT 339 /* 340 * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. 341 * This will increase the amount of PCI address space available for 342 * for mapping RAM. 343 */ 344 #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS 345 #else 346 #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ 347 + CONFIG_SYS_PCIE1_MEM_SIZE) 348 #endif 349 #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ 350 + CONFIG_SYS_PCIE1_MEM_SIZE) 351 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ 352 + CONFIG_SYS_PCIE1_MEM_SIZE) 353 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 354 #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ 355 + CONFIG_SYS_PCIE1_MEM_SIZE) 356 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 357 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 358 #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ 359 + CONFIG_SYS_PCIE1_IO_SIZE) 360 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ 361 + CONFIG_SYS_PCIE1_IO_SIZE) 362 #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ 363 + CONFIG_SYS_PCIE1_IO_SIZE) 364 #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE 365 366 #if defined(CONFIG_PCI) 367 368 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 369 370 #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE 371 372 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 373 374 #define CONFIG_RTL8139 375 376 #undef CONFIG_EEPRO100 377 #undef CONFIG_TULIP 378 379 /************************************************************ 380 * USB support 381 ************************************************************/ 382 #define CONFIG_PCI_OHCI 1 383 #define CONFIG_USB_OHCI_NEW 1 384 #define CONFIG_USB_KEYBOARD 1 385 #define CONFIG_SYS_STDIO_DEREGISTER 386 #define CONFIG_SYS_USB_EVENT_POLL 1 387 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 388 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 389 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 390 391 /*PCIE video card used*/ 392 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 393 394 /*PCI video card used*/ 395 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ 396 397 /* video */ 398 #define CONFIG_VIDEO 399 400 #if defined(CONFIG_VIDEO) 401 #define CONFIG_BIOSEMU 402 #define CONFIG_CFB_CONSOLE 403 #define CONFIG_VIDEO_SW_CURSOR 404 #define CONFIG_VGA_AS_SINGLE_DEVICE 405 #define CONFIG_ATI_RADEON_FB 406 #define CONFIG_VIDEO_LOGO 407 /*#define CONFIG_CONSOLE_CURSOR*/ 408 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT 409 #endif 410 411 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 412 413 #define CONFIG_DOS_PARTITION 414 #define CONFIG_SCSI_AHCI 415 416 #ifdef CONFIG_SCSI_AHCI 417 #define CONFIG_LIBATA 418 #define CONFIG_SATA_ULI5288 419 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 420 #define CONFIG_SYS_SCSI_MAX_LUN 1 421 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 422 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 423 #endif 424 425 #endif /* CONFIG_PCI */ 426 427 #if defined(CONFIG_TSEC_ENET) 428 429 #define CONFIG_MII 1 /* MII PHY management */ 430 431 #define CONFIG_TSEC1 1 432 #define CONFIG_TSEC1_NAME "eTSEC1" 433 #define CONFIG_TSEC2 1 434 #define CONFIG_TSEC2_NAME "eTSEC2" 435 #define CONFIG_TSEC3 1 436 #define CONFIG_TSEC3_NAME "eTSEC3" 437 #define CONFIG_TSEC4 1 438 #define CONFIG_TSEC4_NAME "eTSEC4" 439 440 #define TSEC1_PHY_ADDR 0 441 #define TSEC2_PHY_ADDR 1 442 #define TSEC3_PHY_ADDR 2 443 #define TSEC4_PHY_ADDR 3 444 #define TSEC1_PHYIDX 0 445 #define TSEC2_PHYIDX 0 446 #define TSEC3_PHYIDX 0 447 #define TSEC4_PHYIDX 0 448 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 449 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 450 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 451 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 452 453 #define CONFIG_ETHPRIME "eTSEC1" 454 455 #endif /* CONFIG_TSEC_ENET */ 456 457 458 #ifdef CONFIG_PHYS_64BIT 459 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) 460 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) 461 462 /* Put physical address into the BAT format */ 463 #define BAT_PHYS_ADDR(low, high) \ 464 (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) 465 /* Convert high/low pairs to actual 64-bit value */ 466 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) 467 #else 468 /* 32-bit systems just ignore the "high" bits */ 469 #define BAT_PHYS_ADDR(low, high) (low) 470 #define PAIRED_PHYS_TO_PHYS(low, high) (low) 471 #endif 472 473 /* 474 * BAT0 DDR 475 */ 476 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 477 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 478 479 /* 480 * BAT1 LBC (PIXIS/CF) 481 */ 482 #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 483 CONFIG_SYS_PHYS_ADDR_HIGH) \ 484 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 485 BATL_GUARDEDSTORAGE) 486 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ 487 | BATU_VS | BATU_VP) 488 #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 489 CONFIG_SYS_PHYS_ADDR_HIGH) \ 490 | BATL_PP_RW | BATL_MEMCOHERENCE) 491 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 492 493 /* if CONFIG_PCI: 494 * BAT2 PCIE1 and PCIE1 MEM 495 * if CONFIG_RIO 496 * BAT2 Rapidio Memory 497 */ 498 #ifdef CONFIG_PCI 499 #define CONFIG_PCI_INDIRECT_BRIDGE 500 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 501 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 502 | BATL_PP_RW | BATL_CACHEINHIBIT \ 503 | BATL_GUARDEDSTORAGE) 504 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ 505 | BATU_VS | BATU_VP) 506 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 507 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 508 | BATL_PP_RW | BATL_CACHEINHIBIT) 509 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 510 #else /* CONFIG_RIO */ 511 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 512 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 513 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 514 BATL_GUARDEDSTORAGE) 515 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ 516 | BATU_VS | BATU_VP) 517 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 518 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 519 | BATL_PP_RW | BATL_CACHEINHIBIT) 520 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 521 #endif 522 523 /* 524 * BAT3 CCSR Space 525 */ 526 #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 527 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 528 | BATL_PP_RW | BATL_CACHEINHIBIT \ 529 | BATL_GUARDEDSTORAGE) 530 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ 531 | BATU_VP) 532 #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 533 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 534 | BATL_PP_RW | BATL_CACHEINHIBIT) 535 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 536 537 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 538 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 539 | BATL_PP_RW | BATL_CACHEINHIBIT \ 540 | BATL_GUARDEDSTORAGE) 541 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 542 | BATU_BL_1M | BATU_VS | BATU_VP) 543 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 544 | BATL_PP_RW | BATL_CACHEINHIBIT) 545 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 546 #endif 547 548 /* 549 * BAT4 PCIE1_IO and PCIE2_IO 550 */ 551 #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 552 CONFIG_SYS_PHYS_ADDR_HIGH) \ 553 | BATL_PP_RW | BATL_CACHEINHIBIT \ 554 | BATL_GUARDEDSTORAGE) 555 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ 556 | BATU_VS | BATU_VP) 557 #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 558 CONFIG_SYS_PHYS_ADDR_HIGH) \ 559 | BATL_PP_RW | BATL_CACHEINHIBIT) 560 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 561 562 /* 563 * BAT5 Init RAM for stack in the CPU DCache (no backing memory) 564 */ 565 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 566 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 567 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 568 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 569 570 /* 571 * BAT6 FLASH 572 */ 573 #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 574 CONFIG_SYS_PHYS_ADDR_HIGH) \ 575 | BATL_PP_RW | BATL_CACHEINHIBIT \ 576 | BATL_GUARDEDSTORAGE) 577 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ 578 | BATU_VP) 579 #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 580 CONFIG_SYS_PHYS_ADDR_HIGH) \ 581 | BATL_PP_RW | BATL_MEMCOHERENCE) 582 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 583 584 /* Map the last 1M of flash where we're running from reset */ 585 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 586 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 587 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 588 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 589 | BATL_MEMCOHERENCE) 590 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 591 592 /* 593 * BAT7 FREE - used later for tmp mappings 594 */ 595 #define CONFIG_SYS_DBAT7L 0x00000000 596 #define CONFIG_SYS_DBAT7U 0x00000000 597 #define CONFIG_SYS_IBAT7L 0x00000000 598 #define CONFIG_SYS_IBAT7U 0x00000000 599 600 /* 601 * Environment 602 */ 603 #ifndef CONFIG_SYS_RAMBOOT 604 #define CONFIG_ENV_IS_IN_FLASH 1 605 #define CONFIG_ENV_ADDR \ 606 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 607 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 608 #else 609 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 610 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 611 #endif 612 #define CONFIG_ENV_SIZE 0x2000 613 614 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 615 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 616 617 618 /* 619 * BOOTP options 620 */ 621 #define CONFIG_BOOTP_BOOTFILESIZE 622 #define CONFIG_BOOTP_BOOTPATH 623 #define CONFIG_BOOTP_GATEWAY 624 #define CONFIG_BOOTP_HOSTNAME 625 626 627 /* 628 * Command line configuration. 629 */ 630 #include <config_cmd_default.h> 631 632 #define CONFIG_CMD_PING 633 #define CONFIG_CMD_I2C 634 #define CONFIG_CMD_REGINFO 635 636 #if defined(CONFIG_SYS_RAMBOOT) 637 #undef CONFIG_CMD_SAVEENV 638 #endif 639 640 #if defined(CONFIG_PCI) 641 #define CONFIG_CMD_PCI 642 #define CONFIG_CMD_SCSI 643 #define CONFIG_CMD_EXT2 644 #define CONFIG_CMD_USB 645 #endif 646 647 648 #undef CONFIG_WATCHDOG /* watchdog disabled */ 649 650 /* 651 * Miscellaneous configurable options 652 */ 653 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 654 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 655 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 656 657 #if defined(CONFIG_CMD_KGDB) 658 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 659 #else 660 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 661 #endif 662 663 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 664 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 665 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 666 667 /* 668 * For booting Linux, the board info and command line data 669 * have to be in the first 8 MB of memory, since this is 670 * the maximum mapped by the Linux kernel during initialization. 671 */ 672 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 673 674 #if defined(CONFIG_CMD_KGDB) 675 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 676 #endif 677 678 /* 679 * Environment Configuration 680 */ 681 682 /* The mac addresses for all ethernet interface */ 683 #if defined(CONFIG_TSEC_ENET) 684 #define CONFIG_ETHADDR 00:E0:0C:00:00:01 685 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 686 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 687 #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD 688 #endif 689 690 #define CONFIG_HAS_ETH0 1 691 #define CONFIG_HAS_ETH1 1 692 #define CONFIG_HAS_ETH2 1 693 #define CONFIG_HAS_ETH3 1 694 695 #define CONFIG_IPADDR 192.168.1.100 696 697 #define CONFIG_HOSTNAME unknown 698 #define CONFIG_ROOTPATH "/opt/nfsroot" 699 #define CONFIG_BOOTFILE "uImage" 700 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 701 702 #define CONFIG_SERVERIP 192.168.1.1 703 #define CONFIG_GATEWAYIP 192.168.1.1 704 #define CONFIG_NETMASK 255.255.255.0 705 706 /* default location for tftp and bootm */ 707 #define CONFIG_LOADADDR 1000000 708 709 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 710 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 711 712 #define CONFIG_BAUDRATE 115200 713 714 #define CONFIG_EXTRA_ENV_SETTINGS \ 715 "netdev=eth0\0" \ 716 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 717 "tftpflash=tftpboot $loadaddr $uboot; " \ 718 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 719 " +$filesize; " \ 720 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 721 " +$filesize; " \ 722 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 723 " $filesize; " \ 724 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 725 " +$filesize; " \ 726 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 727 " $filesize\0" \ 728 "consoledev=ttyS0\0" \ 729 "ramdiskaddr=2000000\0" \ 730 "ramdiskfile=your.ramdisk.u-boot\0" \ 731 "fdtaddr=c00000\0" \ 732 "fdtfile=mpc8641_hpcn.dtb\0" \ 733 "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ 734 "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ 735 "maxcpus=2" 736 737 738 #define CONFIG_NFSBOOTCOMMAND \ 739 "setenv bootargs root=/dev/nfs rw " \ 740 "nfsroot=$serverip:$rootpath " \ 741 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 742 "console=$consoledev,$baudrate $othbootargs;" \ 743 "tftp $loadaddr $bootfile;" \ 744 "tftp $fdtaddr $fdtfile;" \ 745 "bootm $loadaddr - $fdtaddr" 746 747 #define CONFIG_RAMBOOTCOMMAND \ 748 "setenv bootargs root=/dev/ram rw " \ 749 "console=$consoledev,$baudrate $othbootargs;" \ 750 "tftp $ramdiskaddr $ramdiskfile;" \ 751 "tftp $loadaddr $bootfile;" \ 752 "tftp $fdtaddr $fdtfile;" \ 753 "bootm $loadaddr $ramdiskaddr $fdtaddr" 754 755 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 756 757 #endif /* __CONFIG_H */ 758