1 /* 2 * Copyright 2006, 2010-2011 Freescale Semiconductor. 3 * 4 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * MPC8641HPCN board configuration file 11 * 12 * Make sure you change the MAC address and other network params first, 13 * search for CONFIG_SERVERIP, etc. in this file. 14 */ 15 16 #ifndef __CONFIG_H 17 #define __CONFIG_H 18 19 /* High Level Configuration Options */ 20 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 21 #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ 22 #define CONFIG_MP 1 /* support multiple processors */ 23 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 24 #define CONFIG_ADDR_MAP 1 /* Use addr map */ 25 26 /* 27 * default CCSRBAR is at 0xff700000 28 * assume U-Boot is less than 0.5MB 29 */ 30 #define CONFIG_SYS_TEXT_BASE 0xeff00000 31 32 #ifdef RUN_DIAG 33 #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE 34 #endif 35 36 /* 37 * virtual address to be used for temporary mappings. There 38 * should be 128k free at this VA. 39 */ 40 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 41 42 #define CONFIG_SYS_SRIO 43 #define CONFIG_SRIO1 /* SRIO port 1 */ 44 45 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 46 #define CONFIG_PCIE1 1 /* PCIE controller 1 (ULI bridge) */ 47 #define CONFIG_PCIE2 1 /* PCIE controller 2 (slot) */ 48 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 49 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 50 #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ 51 52 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 53 #define CONFIG_ENV_OVERWRITE 54 55 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 56 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 57 #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ 58 59 #define CONFIG_ALTIVEC 1 60 61 /* 62 * L2CR setup -- make sure this is right for your board! 63 */ 64 #define CONFIG_SYS_L2 65 #define L2_INIT 0 66 #define L2_ENABLE (L2CR_L2E) 67 68 #ifndef CONFIG_SYS_CLK_FREQ 69 #ifndef __ASSEMBLY__ 70 extern unsigned long get_board_sys_clk(unsigned long dummy); 71 #endif 72 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 73 #endif 74 75 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 76 #define CONFIG_SYS_MEMTEST_END 0x00400000 77 78 /* 79 * With the exception of PCI Memory and Rapid IO, most devices will simply 80 * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA 81 * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. 82 */ 83 #ifdef CONFIG_PHYS_64BIT 84 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f 85 #else 86 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 87 #endif 88 89 /* 90 * Base addresses -- Note these are effective addresses where the 91 * actual resources get mapped (not physical addresses) 92 */ 93 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 94 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 95 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 96 97 /* Physical addresses */ 98 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 99 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH 100 #define CONFIG_SYS_CCSRBAR_PHYS \ 101 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 102 CONFIG_SYS_CCSRBAR_PHYS_HIGH) 103 104 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ 105 106 /* 107 * DDR Setup 108 */ 109 #define CONFIG_SYS_FSL_DDR2 110 #undef CONFIG_FSL_DDR_INTERACTIVE 111 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 112 #define CONFIG_DDR_SPD 113 114 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 115 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 116 117 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 118 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 119 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 120 #define CONFIG_VERY_BIG_RAM 121 122 #define CONFIG_NUM_DDR_CONTROLLERS 2 123 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 124 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 125 126 /* 127 * I2C addresses of SPD EEPROMs 128 */ 129 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 130 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ 131 #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ 132 #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ 133 134 /* 135 * These are used when DDR doesn't use SPD. 136 */ 137 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 138 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 139 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 140 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 141 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 142 #define CONFIG_SYS_DDR_TIMING_1 0x39357322 143 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 144 #define CONFIG_SYS_DDR_MODE_1 0x00480432 145 #define CONFIG_SYS_DDR_MODE_2 0x00000000 146 #define CONFIG_SYS_DDR_INTERVAL 0x06090100 147 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 148 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 149 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 150 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 151 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 152 #define CONFIG_SYS_DDR_CONTROL2 0x04400000 153 154 #define CONFIG_ID_EEPROM 155 #define CONFIG_SYS_I2C_EEPROM_NXID 156 #define CONFIG_ID_EEPROM 157 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 158 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 159 160 #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ 161 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE 162 #define CONFIG_SYS_FLASH_BASE_PHYS \ 163 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 164 CONFIG_SYS_PHYS_ADDR_HIGH) 165 166 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 167 168 #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 169 | 0x00001001) /* port size 16bit */ 170 #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ 171 172 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ 173 | 0x00001001) /* port size 16bit */ 174 #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ 175 176 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ 177 | 0x00000801) /* port size 8bit */ 178 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ 179 180 /* 181 * The LBC_BASE is the base of the region that contains the PIXIS and the CF. 182 * The PIXIS and CF by themselves aren't large enough to take up the 128k 183 * required for the smallest BAT mapping, so there's a 64k hole. 184 */ 185 #define CONFIG_SYS_LBC_BASE 0xffde0000 186 #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE 187 188 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 189 #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) 190 #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) 191 #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ 192 CONFIG_SYS_PHYS_ADDR_HIGH) 193 #define PIXIS_SIZE 0x00008000 /* 32k */ 194 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 195 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 196 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 197 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 198 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ 199 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 200 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 201 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 202 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 203 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 204 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 205 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 206 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 207 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 208 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 209 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 210 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 211 212 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ 213 #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) 214 #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) 215 216 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 217 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 218 219 #undef CONFIG_SYS_FLASH_CHECKSUM 220 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 221 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 222 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 223 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 224 225 #define CONFIG_FLASH_CFI_DRIVER 226 #define CONFIG_SYS_FLASH_CFI 227 #define CONFIG_SYS_FLASH_EMPTY_INFO 228 229 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 230 #define CONFIG_SYS_RAMBOOT 231 #else 232 #undef CONFIG_SYS_RAMBOOT 233 #endif 234 235 #if defined(CONFIG_SYS_RAMBOOT) 236 #undef CONFIG_SPD_EEPROM 237 #define CONFIG_SYS_SDRAM_SIZE 256 238 #endif 239 240 #undef CONFIG_CLOCKS_IN_MHZ 241 242 #define CONFIG_SYS_INIT_RAM_LOCK 1 243 #ifndef CONFIG_SYS_INIT_RAM_LOCK 244 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 245 #else 246 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 247 #endif 248 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 249 250 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 251 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 252 253 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 254 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 255 256 /* Serial Port */ 257 #define CONFIG_CONS_INDEX 1 258 #define CONFIG_SYS_NS16550_SERIAL 259 #define CONFIG_SYS_NS16550_REG_SIZE 1 260 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 261 262 #define CONFIG_SYS_BAUDRATE_TABLE \ 263 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 264 265 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 266 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 267 268 /* 269 * I2C 270 */ 271 #define CONFIG_SYS_I2C 272 #define CONFIG_SYS_I2C_FSL 273 #define CONFIG_SYS_FSL_I2C_SPEED 400000 274 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 275 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 276 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 277 278 /* 279 * RapidIO MMU 280 */ 281 #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ 282 #ifdef CONFIG_PHYS_64BIT 283 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 284 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c 285 #else 286 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE 287 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 288 #endif 289 #define CONFIG_SYS_SRIO1_MEM_PHYS \ 290 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 291 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) 292 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 293 294 /* 295 * General PCI 296 * Addresses are mapped 1-1. 297 */ 298 299 #define CONFIG_SYS_PCIE1_NAME "ULI" 300 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 301 #ifdef CONFIG_PHYS_64BIT 302 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 303 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 304 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c 305 #else 306 #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT 307 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT 308 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 309 #endif 310 #define CONFIG_SYS_PCIE1_MEM_PHYS \ 311 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 312 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) 313 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 314 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 315 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 316 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT 317 #define CONFIG_SYS_PCIE1_IO_PHYS \ 318 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 319 CONFIG_SYS_PHYS_ADDR_HIGH) 320 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ 321 322 #ifdef CONFIG_PHYS_64BIT 323 /* 324 * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. 325 * This will increase the amount of PCI address space available for 326 * for mapping RAM. 327 */ 328 #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS 329 #else 330 #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ 331 + CONFIG_SYS_PCIE1_MEM_SIZE) 332 #endif 333 #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ 334 + CONFIG_SYS_PCIE1_MEM_SIZE) 335 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ 336 + CONFIG_SYS_PCIE1_MEM_SIZE) 337 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 338 #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ 339 + CONFIG_SYS_PCIE1_MEM_SIZE) 340 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 341 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 342 #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ 343 + CONFIG_SYS_PCIE1_IO_SIZE) 344 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ 345 + CONFIG_SYS_PCIE1_IO_SIZE) 346 #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ 347 + CONFIG_SYS_PCIE1_IO_SIZE) 348 #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE 349 350 #if defined(CONFIG_PCI) 351 352 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 353 354 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 355 356 #undef CONFIG_EEPRO100 357 #undef CONFIG_TULIP 358 359 /************************************************************ 360 * USB support 361 ************************************************************/ 362 #define CONFIG_PCI_OHCI 1 363 #define CONFIG_USB_OHCI_NEW 1 364 #define CONFIG_USB_KEYBOARD 1 365 #define CONFIG_SYS_STDIO_DEREGISTER 366 #define CONFIG_SYS_USB_EVENT_POLL 1 367 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 368 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 369 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 370 371 /*PCIE video card used*/ 372 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 373 374 /*PCI video card used*/ 375 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ 376 377 /* video */ 378 #define CONFIG_VIDEO 379 380 #if defined(CONFIG_VIDEO) 381 #define CONFIG_BIOSEMU 382 #define CONFIG_CFB_CONSOLE 383 #define CONFIG_VIDEO_SW_CURSOR 384 #define CONFIG_VGA_AS_SINGLE_DEVICE 385 #define CONFIG_ATI_RADEON_FB 386 #define CONFIG_VIDEO_LOGO 387 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT 388 #endif 389 390 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 391 392 #define CONFIG_DOS_PARTITION 393 #define CONFIG_SCSI_AHCI 394 395 #ifdef CONFIG_SCSI_AHCI 396 #define CONFIG_LIBATA 397 #define CONFIG_SATA_ULI5288 398 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 399 #define CONFIG_SYS_SCSI_MAX_LUN 1 400 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 401 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 402 #endif 403 404 #endif /* CONFIG_PCI */ 405 406 #if defined(CONFIG_TSEC_ENET) 407 408 #define CONFIG_MII 1 /* MII PHY management */ 409 410 #define CONFIG_TSEC1 1 411 #define CONFIG_TSEC1_NAME "eTSEC1" 412 #define CONFIG_TSEC2 1 413 #define CONFIG_TSEC2_NAME "eTSEC2" 414 #define CONFIG_TSEC3 1 415 #define CONFIG_TSEC3_NAME "eTSEC3" 416 #define CONFIG_TSEC4 1 417 #define CONFIG_TSEC4_NAME "eTSEC4" 418 419 #define TSEC1_PHY_ADDR 0 420 #define TSEC2_PHY_ADDR 1 421 #define TSEC3_PHY_ADDR 2 422 #define TSEC4_PHY_ADDR 3 423 #define TSEC1_PHYIDX 0 424 #define TSEC2_PHYIDX 0 425 #define TSEC3_PHYIDX 0 426 #define TSEC4_PHYIDX 0 427 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 428 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 429 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 430 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 431 432 #define CONFIG_ETHPRIME "eTSEC1" 433 434 #endif /* CONFIG_TSEC_ENET */ 435 436 #ifdef CONFIG_PHYS_64BIT 437 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) 438 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) 439 440 /* Put physical address into the BAT format */ 441 #define BAT_PHYS_ADDR(low, high) \ 442 (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) 443 /* Convert high/low pairs to actual 64-bit value */ 444 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) 445 #else 446 /* 32-bit systems just ignore the "high" bits */ 447 #define BAT_PHYS_ADDR(low, high) (low) 448 #define PAIRED_PHYS_TO_PHYS(low, high) (low) 449 #endif 450 451 /* 452 * BAT0 DDR 453 */ 454 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 455 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 456 457 /* 458 * BAT1 LBC (PIXIS/CF) 459 */ 460 #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 461 CONFIG_SYS_PHYS_ADDR_HIGH) \ 462 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 463 BATL_GUARDEDSTORAGE) 464 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ 465 | BATU_VS | BATU_VP) 466 #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 467 CONFIG_SYS_PHYS_ADDR_HIGH) \ 468 | BATL_PP_RW | BATL_MEMCOHERENCE) 469 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 470 471 /* if CONFIG_PCI: 472 * BAT2 PCIE1 and PCIE1 MEM 473 * if CONFIG_RIO 474 * BAT2 Rapidio Memory 475 */ 476 #ifdef CONFIG_PCI 477 #define CONFIG_PCI_INDIRECT_BRIDGE 478 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 479 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 480 | BATL_PP_RW | BATL_CACHEINHIBIT \ 481 | BATL_GUARDEDSTORAGE) 482 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ 483 | BATU_VS | BATU_VP) 484 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 485 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 486 | BATL_PP_RW | BATL_CACHEINHIBIT) 487 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 488 #else /* CONFIG_RIO */ 489 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 490 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 491 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 492 BATL_GUARDEDSTORAGE) 493 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ 494 | BATU_VS | BATU_VP) 495 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 496 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 497 | BATL_PP_RW | BATL_CACHEINHIBIT) 498 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 499 #endif 500 501 /* 502 * BAT3 CCSR Space 503 */ 504 #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 505 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 506 | BATL_PP_RW | BATL_CACHEINHIBIT \ 507 | BATL_GUARDEDSTORAGE) 508 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ 509 | BATU_VP) 510 #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 511 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 512 | BATL_PP_RW | BATL_CACHEINHIBIT) 513 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 514 515 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 516 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 517 | BATL_PP_RW | BATL_CACHEINHIBIT \ 518 | BATL_GUARDEDSTORAGE) 519 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 520 | BATU_BL_1M | BATU_VS | BATU_VP) 521 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 522 | BATL_PP_RW | BATL_CACHEINHIBIT) 523 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 524 #endif 525 526 /* 527 * BAT4 PCIE1_IO and PCIE2_IO 528 */ 529 #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 530 CONFIG_SYS_PHYS_ADDR_HIGH) \ 531 | BATL_PP_RW | BATL_CACHEINHIBIT \ 532 | BATL_GUARDEDSTORAGE) 533 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ 534 | BATU_VS | BATU_VP) 535 #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 536 CONFIG_SYS_PHYS_ADDR_HIGH) \ 537 | BATL_PP_RW | BATL_CACHEINHIBIT) 538 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 539 540 /* 541 * BAT5 Init RAM for stack in the CPU DCache (no backing memory) 542 */ 543 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 544 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 545 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 546 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 547 548 /* 549 * BAT6 FLASH 550 */ 551 #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 552 CONFIG_SYS_PHYS_ADDR_HIGH) \ 553 | BATL_PP_RW | BATL_CACHEINHIBIT \ 554 | BATL_GUARDEDSTORAGE) 555 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ 556 | BATU_VP) 557 #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 558 CONFIG_SYS_PHYS_ADDR_HIGH) \ 559 | BATL_PP_RW | BATL_MEMCOHERENCE) 560 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 561 562 /* Map the last 1M of flash where we're running from reset */ 563 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 564 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 565 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 566 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 567 | BATL_MEMCOHERENCE) 568 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 569 570 /* 571 * BAT7 FREE - used later for tmp mappings 572 */ 573 #define CONFIG_SYS_DBAT7L 0x00000000 574 #define CONFIG_SYS_DBAT7U 0x00000000 575 #define CONFIG_SYS_IBAT7L 0x00000000 576 #define CONFIG_SYS_IBAT7U 0x00000000 577 578 /* 579 * Environment 580 */ 581 #ifndef CONFIG_SYS_RAMBOOT 582 #define CONFIG_ENV_IS_IN_FLASH 1 583 #define CONFIG_ENV_ADDR \ 584 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 585 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 586 #else 587 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 588 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 589 #endif 590 #define CONFIG_ENV_SIZE 0x2000 591 592 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 593 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 594 595 /* 596 * BOOTP options 597 */ 598 #define CONFIG_BOOTP_BOOTFILESIZE 599 #define CONFIG_BOOTP_BOOTPATH 600 #define CONFIG_BOOTP_GATEWAY 601 #define CONFIG_BOOTP_HOSTNAME 602 603 /* 604 * Command line configuration. 605 */ 606 #define CONFIG_CMD_REGINFO 607 608 #if defined(CONFIG_PCI) 609 #define CONFIG_CMD_PCI 610 #define CONFIG_SCSI 611 #endif 612 613 #undef CONFIG_WATCHDOG /* watchdog disabled */ 614 615 /* 616 * Miscellaneous configurable options 617 */ 618 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 619 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 620 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 621 622 #if defined(CONFIG_CMD_KGDB) 623 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 624 #else 625 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 626 #endif 627 628 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 629 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 630 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 631 632 /* 633 * For booting Linux, the board info and command line data 634 * have to be in the first 8 MB of memory, since this is 635 * the maximum mapped by the Linux kernel during initialization. 636 */ 637 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ 638 #define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */ 639 640 #if defined(CONFIG_CMD_KGDB) 641 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 642 #endif 643 644 /* 645 * Environment Configuration 646 */ 647 648 #define CONFIG_HAS_ETH0 1 649 #define CONFIG_HAS_ETH1 1 650 #define CONFIG_HAS_ETH2 1 651 #define CONFIG_HAS_ETH3 1 652 653 #define CONFIG_IPADDR 192.168.1.100 654 655 #define CONFIG_HOSTNAME unknown 656 #define CONFIG_ROOTPATH "/opt/nfsroot" 657 #define CONFIG_BOOTFILE "uImage" 658 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 659 660 #define CONFIG_SERVERIP 192.168.1.1 661 #define CONFIG_GATEWAYIP 192.168.1.1 662 #define CONFIG_NETMASK 255.255.255.0 663 664 /* default location for tftp and bootm */ 665 #define CONFIG_LOADADDR 0x10000000 666 667 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 668 669 #define CONFIG_BAUDRATE 115200 670 671 #define CONFIG_EXTRA_ENV_SETTINGS \ 672 "netdev=eth0\0" \ 673 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 674 "tftpflash=tftpboot $loadaddr $uboot; " \ 675 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 676 " +$filesize; " \ 677 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 678 " +$filesize; " \ 679 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 680 " $filesize; " \ 681 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 682 " +$filesize; " \ 683 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 684 " $filesize\0" \ 685 "consoledev=ttyS0\0" \ 686 "ramdiskaddr=0x18000000\0" \ 687 "ramdiskfile=your.ramdisk.u-boot\0" \ 688 "fdtaddr=0x17c00000\0" \ 689 "fdtfile=mpc8641_hpcn.dtb\0" \ 690 "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ 691 "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ 692 "maxcpus=2" 693 694 #define CONFIG_NFSBOOTCOMMAND \ 695 "setenv bootargs root=/dev/nfs rw " \ 696 "nfsroot=$serverip:$rootpath " \ 697 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 698 "console=$consoledev,$baudrate $othbootargs;" \ 699 "tftp $loadaddr $bootfile;" \ 700 "tftp $fdtaddr $fdtfile;" \ 701 "bootm $loadaddr - $fdtaddr" 702 703 #define CONFIG_RAMBOOTCOMMAND \ 704 "setenv bootargs root=/dev/ram rw " \ 705 "console=$consoledev,$baudrate $othbootargs;" \ 706 "tftp $ramdiskaddr $ramdiskfile;" \ 707 "tftp $loadaddr $bootfile;" \ 708 "tftp $fdtaddr $fdtfile;" \ 709 "bootm $loadaddr $ramdiskaddr $fdtaddr" 710 711 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 712 713 #endif /* __CONFIG_H */ 714