1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2006, 2010-2011 Freescale Semiconductor. 4 * 5 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 6 */ 7 8 /* 9 * MPC8641HPCN board configuration file 10 * 11 * Make sure you change the MAC address and other network params first, 12 * search for CONFIG_SERVERIP, etc. in this file. 13 */ 14 15 #ifndef __CONFIG_H 16 #define __CONFIG_H 17 18 /* High Level Configuration Options */ 19 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 20 #define CONFIG_ADDR_MAP 1 /* Use addr map */ 21 22 /* 23 * default CCSRBAR is at 0xff700000 24 * assume U-Boot is less than 0.5MB 25 */ 26 27 #ifdef RUN_DIAG 28 #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE 29 #endif 30 31 /* 32 * virtual address to be used for temporary mappings. There 33 * should be 128k free at this VA. 34 */ 35 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 36 37 #define CONFIG_SYS_SRIO 38 #define CONFIG_SRIO1 /* SRIO port 1 */ 39 40 #define CONFIG_PCIE1 1 /* PCIE controller 1 (ULI bridge) */ 41 #define CONFIG_PCIE2 1 /* PCIE controller 2 (slot) */ 42 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 43 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 44 45 #define CONFIG_ENV_OVERWRITE 46 47 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 48 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 49 #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ 50 51 #define CONFIG_ALTIVEC 1 52 53 /* 54 * L2CR setup -- make sure this is right for your board! 55 */ 56 #define CONFIG_SYS_L2 57 #define L2_INIT 0 58 #define L2_ENABLE (L2CR_L2E) 59 60 #ifndef CONFIG_SYS_CLK_FREQ 61 #ifndef __ASSEMBLY__ 62 extern unsigned long get_board_sys_clk(unsigned long dummy); 63 #endif 64 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 65 #endif 66 67 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 68 #define CONFIG_SYS_MEMTEST_END 0x00400000 69 70 /* 71 * With the exception of PCI Memory and Rapid IO, most devices will simply 72 * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA 73 * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. 74 */ 75 #ifdef CONFIG_PHYS_64BIT 76 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f 77 #else 78 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 79 #endif 80 81 /* 82 * Base addresses -- Note these are effective addresses where the 83 * actual resources get mapped (not physical addresses) 84 */ 85 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 86 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 87 88 /* Physical addresses */ 89 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 90 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH 91 #define CONFIG_SYS_CCSRBAR_PHYS \ 92 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 93 CONFIG_SYS_CCSRBAR_PHYS_HIGH) 94 95 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ 96 97 /* 98 * DDR Setup 99 */ 100 #define CONFIG_FSL_DDR_INTERACTIVE 101 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 102 #define CONFIG_DDR_SPD 103 104 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 105 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 106 107 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 108 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 109 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 110 #define CONFIG_VERY_BIG_RAM 111 112 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 113 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 114 115 /* 116 * I2C addresses of SPD EEPROMs 117 */ 118 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 119 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ 120 #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ 121 #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ 122 123 /* 124 * These are used when DDR doesn't use SPD. 125 */ 126 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 127 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 128 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 129 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 130 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 131 #define CONFIG_SYS_DDR_TIMING_1 0x39357322 132 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 133 #define CONFIG_SYS_DDR_MODE_1 0x00480432 134 #define CONFIG_SYS_DDR_MODE_2 0x00000000 135 #define CONFIG_SYS_DDR_INTERVAL 0x06090100 136 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 137 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 138 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 139 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 140 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 141 #define CONFIG_SYS_DDR_CONTROL2 0x04400000 142 143 #define CONFIG_ID_EEPROM 144 #define CONFIG_SYS_I2C_EEPROM_NXID 145 #define CONFIG_ID_EEPROM 146 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 147 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 148 149 #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ 150 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE 151 #define CONFIG_SYS_FLASH_BASE_PHYS \ 152 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 153 CONFIG_SYS_PHYS_ADDR_HIGH) 154 155 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 156 157 #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 158 | 0x00001001) /* port size 16bit */ 159 #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ 160 161 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ 162 | 0x00001001) /* port size 16bit */ 163 #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ 164 165 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ 166 | 0x00000801) /* port size 8bit */ 167 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ 168 169 /* 170 * The LBC_BASE is the base of the region that contains the PIXIS and the CF. 171 * The PIXIS and CF by themselves aren't large enough to take up the 128k 172 * required for the smallest BAT mapping, so there's a 64k hole. 173 */ 174 #define CONFIG_SYS_LBC_BASE 0xffde0000 175 #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE 176 177 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 178 #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) 179 #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) 180 #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ 181 CONFIG_SYS_PHYS_ADDR_HIGH) 182 #define PIXIS_SIZE 0x00008000 /* 32k */ 183 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 184 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 185 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 186 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 187 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ 188 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 189 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 190 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 191 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 192 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 193 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 194 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 195 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 196 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 197 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 198 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 199 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 200 201 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ 202 #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) 203 #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) 204 205 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 206 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 207 208 #undef CONFIG_SYS_FLASH_CHECKSUM 209 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 210 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 211 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 212 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 213 214 #define CONFIG_SYS_FLASH_EMPTY_INFO 215 216 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 217 #define CONFIG_SYS_RAMBOOT 218 #else 219 #undef CONFIG_SYS_RAMBOOT 220 #endif 221 222 #if defined(CONFIG_SYS_RAMBOOT) 223 #undef CONFIG_SPD_EEPROM 224 #define CONFIG_SYS_SDRAM_SIZE 256 225 #endif 226 227 #undef CONFIG_CLOCKS_IN_MHZ 228 229 #define CONFIG_SYS_INIT_RAM_LOCK 1 230 #ifndef CONFIG_SYS_INIT_RAM_LOCK 231 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 232 #else 233 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 234 #endif 235 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 236 237 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 238 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 239 240 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 241 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 242 243 /* Serial Port */ 244 #define CONFIG_SYS_NS16550_SERIAL 245 #define CONFIG_SYS_NS16550_REG_SIZE 1 246 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 247 248 #define CONFIG_SYS_BAUDRATE_TABLE \ 249 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 250 251 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 252 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 253 254 /* 255 * I2C 256 */ 257 #define CONFIG_SYS_I2C 258 #define CONFIG_SYS_I2C_FSL 259 #define CONFIG_SYS_FSL_I2C_SPEED 400000 260 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 261 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 262 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 263 264 /* 265 * RapidIO MMU 266 */ 267 #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ 268 #ifdef CONFIG_PHYS_64BIT 269 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 270 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c 271 #else 272 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE 273 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 274 #endif 275 #define CONFIG_SYS_SRIO1_MEM_PHYS \ 276 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 277 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) 278 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 279 280 /* 281 * General PCI 282 * Addresses are mapped 1-1. 283 */ 284 285 #define CONFIG_SYS_PCIE1_NAME "ULI" 286 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 287 #ifdef CONFIG_PHYS_64BIT 288 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 289 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 290 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c 291 #else 292 #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT 293 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT 294 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 295 #endif 296 #define CONFIG_SYS_PCIE1_MEM_PHYS \ 297 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 298 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) 299 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 300 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 301 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 302 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT 303 #define CONFIG_SYS_PCIE1_IO_PHYS \ 304 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 305 CONFIG_SYS_PHYS_ADDR_HIGH) 306 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ 307 308 #ifdef CONFIG_PHYS_64BIT 309 /* 310 * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. 311 * This will increase the amount of PCI address space available for 312 * for mapping RAM. 313 */ 314 #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS 315 #else 316 #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ 317 + CONFIG_SYS_PCIE1_MEM_SIZE) 318 #endif 319 #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ 320 + CONFIG_SYS_PCIE1_MEM_SIZE) 321 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ 322 + CONFIG_SYS_PCIE1_MEM_SIZE) 323 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 324 #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ 325 + CONFIG_SYS_PCIE1_MEM_SIZE) 326 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 327 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 328 #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ 329 + CONFIG_SYS_PCIE1_IO_SIZE) 330 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ 331 + CONFIG_SYS_PCIE1_IO_SIZE) 332 #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ 333 + CONFIG_SYS_PCIE1_IO_SIZE) 334 #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE 335 336 #if defined(CONFIG_PCI) 337 338 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 339 340 #undef CONFIG_EEPRO100 341 #undef CONFIG_TULIP 342 343 /************************************************************ 344 * USB support 345 ************************************************************/ 346 #define CONFIG_PCI_OHCI 1 347 #define CONFIG_USB_OHCI_NEW 1 348 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 349 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 350 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 351 352 /*PCIE video card used*/ 353 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 354 355 /*PCI video card used*/ 356 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ 357 358 /* video */ 359 360 #if defined(CONFIG_VIDEO) 361 #define CONFIG_BIOSEMU 362 #define CONFIG_ATI_RADEON_FB 363 #define CONFIG_VIDEO_LOGO 364 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT 365 #endif 366 367 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 368 369 #ifdef CONFIG_SCSI_AHCI 370 #define CONFIG_SATA_ULI5288 371 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 372 #define CONFIG_SYS_SCSI_MAX_LUN 1 373 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 374 #endif 375 376 #endif /* CONFIG_PCI */ 377 378 #if defined(CONFIG_TSEC_ENET) 379 #define CONFIG_TSEC1 1 380 #define CONFIG_TSEC1_NAME "eTSEC1" 381 #define CONFIG_TSEC2 1 382 #define CONFIG_TSEC2_NAME "eTSEC2" 383 #define CONFIG_TSEC3 1 384 #define CONFIG_TSEC3_NAME "eTSEC3" 385 #define CONFIG_TSEC4 1 386 #define CONFIG_TSEC4_NAME "eTSEC4" 387 388 #define TSEC1_PHY_ADDR 0 389 #define TSEC2_PHY_ADDR 1 390 #define TSEC3_PHY_ADDR 2 391 #define TSEC4_PHY_ADDR 3 392 #define TSEC1_PHYIDX 0 393 #define TSEC2_PHYIDX 0 394 #define TSEC3_PHYIDX 0 395 #define TSEC4_PHYIDX 0 396 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 397 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 398 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 399 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 400 401 #define CONFIG_ETHPRIME "eTSEC1" 402 403 #endif /* CONFIG_TSEC_ENET */ 404 405 #ifdef CONFIG_PHYS_64BIT 406 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) 407 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) 408 409 /* Put physical address into the BAT format */ 410 #define BAT_PHYS_ADDR(low, high) \ 411 (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) 412 /* Convert high/low pairs to actual 64-bit value */ 413 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) 414 #else 415 /* 32-bit systems just ignore the "high" bits */ 416 #define BAT_PHYS_ADDR(low, high) (low) 417 #define PAIRED_PHYS_TO_PHYS(low, high) (low) 418 #endif 419 420 /* 421 * BAT0 DDR 422 */ 423 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 424 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 425 426 /* 427 * BAT1 LBC (PIXIS/CF) 428 */ 429 #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 430 CONFIG_SYS_PHYS_ADDR_HIGH) \ 431 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 432 BATL_GUARDEDSTORAGE) 433 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ 434 | BATU_VS | BATU_VP) 435 #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 436 CONFIG_SYS_PHYS_ADDR_HIGH) \ 437 | BATL_PP_RW | BATL_MEMCOHERENCE) 438 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 439 440 /* if CONFIG_PCI: 441 * BAT2 PCIE1 and PCIE1 MEM 442 * if CONFIG_RIO 443 * BAT2 Rapidio Memory 444 */ 445 #ifdef CONFIG_PCI 446 #define CONFIG_PCI_INDIRECT_BRIDGE 447 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 448 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 449 | BATL_PP_RW | BATL_CACHEINHIBIT \ 450 | BATL_GUARDEDSTORAGE) 451 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ 452 | BATU_VS | BATU_VP) 453 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 454 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 455 | BATL_PP_RW | BATL_CACHEINHIBIT) 456 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 457 #else /* CONFIG_RIO */ 458 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 459 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 460 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 461 BATL_GUARDEDSTORAGE) 462 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ 463 | BATU_VS | BATU_VP) 464 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 465 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 466 | BATL_PP_RW | BATL_CACHEINHIBIT) 467 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 468 #endif 469 470 /* 471 * BAT3 CCSR Space 472 */ 473 #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 474 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 475 | BATL_PP_RW | BATL_CACHEINHIBIT \ 476 | BATL_GUARDEDSTORAGE) 477 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ 478 | BATU_VP) 479 #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 480 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 481 | BATL_PP_RW | BATL_CACHEINHIBIT) 482 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 483 484 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 485 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 486 | BATL_PP_RW | BATL_CACHEINHIBIT \ 487 | BATL_GUARDEDSTORAGE) 488 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 489 | BATU_BL_1M | BATU_VS | BATU_VP) 490 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 491 | BATL_PP_RW | BATL_CACHEINHIBIT) 492 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 493 #endif 494 495 /* 496 * BAT4 PCIE1_IO and PCIE2_IO 497 */ 498 #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 499 CONFIG_SYS_PHYS_ADDR_HIGH) \ 500 | BATL_PP_RW | BATL_CACHEINHIBIT \ 501 | BATL_GUARDEDSTORAGE) 502 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ 503 | BATU_VS | BATU_VP) 504 #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 505 CONFIG_SYS_PHYS_ADDR_HIGH) \ 506 | BATL_PP_RW | BATL_CACHEINHIBIT) 507 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 508 509 /* 510 * BAT5 Init RAM for stack in the CPU DCache (no backing memory) 511 */ 512 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 513 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 514 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 515 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 516 517 /* 518 * BAT6 FLASH 519 */ 520 #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 521 CONFIG_SYS_PHYS_ADDR_HIGH) \ 522 | BATL_PP_RW | BATL_CACHEINHIBIT \ 523 | BATL_GUARDEDSTORAGE) 524 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ 525 | BATU_VP) 526 #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 527 CONFIG_SYS_PHYS_ADDR_HIGH) \ 528 | BATL_PP_RW | BATL_MEMCOHERENCE) 529 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 530 531 /* Map the last 1M of flash where we're running from reset */ 532 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 533 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 534 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 535 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 536 | BATL_MEMCOHERENCE) 537 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 538 539 /* 540 * BAT7 FREE - used later for tmp mappings 541 */ 542 #define CONFIG_SYS_DBAT7L 0x00000000 543 #define CONFIG_SYS_DBAT7U 0x00000000 544 #define CONFIG_SYS_IBAT7L 0x00000000 545 #define CONFIG_SYS_IBAT7U 0x00000000 546 547 /* 548 * Environment 549 */ 550 #ifndef CONFIG_SYS_RAMBOOT 551 #define CONFIG_ENV_ADDR \ 552 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 553 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 554 #else 555 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 556 #endif 557 #define CONFIG_ENV_SIZE 0x2000 558 559 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 560 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 561 562 /* 563 * BOOTP options 564 */ 565 #define CONFIG_BOOTP_BOOTFILESIZE 566 567 #undef CONFIG_WATCHDOG /* watchdog disabled */ 568 569 /* 570 * Miscellaneous configurable options 571 */ 572 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 573 574 /* 575 * For booting Linux, the board info and command line data 576 * have to be in the first 8 MB of memory, since this is 577 * the maximum mapped by the Linux kernel during initialization. 578 */ 579 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ 580 #define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */ 581 582 #if defined(CONFIG_CMD_KGDB) 583 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 584 #endif 585 586 /* 587 * Environment Configuration 588 */ 589 590 #define CONFIG_HAS_ETH0 1 591 #define CONFIG_HAS_ETH1 1 592 #define CONFIG_HAS_ETH2 1 593 #define CONFIG_HAS_ETH3 1 594 595 #define CONFIG_IPADDR 192.168.1.100 596 597 #define CONFIG_HOSTNAME "unknown" 598 #define CONFIG_ROOTPATH "/opt/nfsroot" 599 #define CONFIG_BOOTFILE "uImage" 600 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 601 602 #define CONFIG_SERVERIP 192.168.1.1 603 #define CONFIG_GATEWAYIP 192.168.1.1 604 #define CONFIG_NETMASK 255.255.255.0 605 606 /* default location for tftp and bootm */ 607 #define CONFIG_LOADADDR 0x10000000 608 609 #define CONFIG_EXTRA_ENV_SETTINGS \ 610 "netdev=eth0\0" \ 611 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 612 "tftpflash=tftpboot $loadaddr $uboot; " \ 613 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 614 " +$filesize; " \ 615 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 616 " +$filesize; " \ 617 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 618 " $filesize; " \ 619 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 620 " +$filesize; " \ 621 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 622 " $filesize\0" \ 623 "consoledev=ttyS0\0" \ 624 "ramdiskaddr=0x18000000\0" \ 625 "ramdiskfile=your.ramdisk.u-boot\0" \ 626 "fdtaddr=0x17c00000\0" \ 627 "fdtfile=mpc8641_hpcn.dtb\0" \ 628 "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ 629 "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ 630 "maxcpus=2" 631 632 #define CONFIG_NFSBOOTCOMMAND \ 633 "setenv bootargs root=/dev/nfs rw " \ 634 "nfsroot=$serverip:$rootpath " \ 635 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 636 "console=$consoledev,$baudrate $othbootargs;" \ 637 "tftp $loadaddr $bootfile;" \ 638 "tftp $fdtaddr $fdtfile;" \ 639 "bootm $loadaddr - $fdtaddr" 640 641 #define CONFIG_RAMBOOTCOMMAND \ 642 "setenv bootargs root=/dev/ram rw " \ 643 "console=$consoledev,$baudrate $othbootargs;" \ 644 "tftp $ramdiskaddr $ramdiskfile;" \ 645 "tftp $loadaddr $bootfile;" \ 646 "tftp $fdtaddr $fdtfile;" \ 647 "bootm $loadaddr $ramdiskaddr $fdtaddr" 648 649 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 650 651 #endif /* __CONFIG_H */ 652