1 /* 2 * Copyright 2006, 2010-2011 Freescale Semiconductor. 3 * 4 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * MPC8641HPCN board configuration file 11 * 12 * Make sure you change the MAC address and other network params first, 13 * search for CONFIG_SERVERIP, etc. in this file. 14 */ 15 16 #ifndef __CONFIG_H 17 #define __CONFIG_H 18 19 #define CONFIG_DISPLAY_BOARDINFO 20 21 /* High Level Configuration Options */ 22 #define CONFIG_MPC8641 1 /* MPC8641 specific */ 23 #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ 24 #define CONFIG_MP 1 /* support multiple processors */ 25 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 26 /*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ 27 #define CONFIG_ADDR_MAP 1 /* Use addr map */ 28 29 /* 30 * default CCSRBAR is at 0xff700000 31 * assume U-Boot is less than 0.5MB 32 */ 33 #define CONFIG_SYS_TEXT_BASE 0xeff00000 34 35 #ifdef RUN_DIAG 36 #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE 37 #endif 38 39 /* 40 * virtual address to be used for temporary mappings. There 41 * should be 128k free at this VA. 42 */ 43 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 44 45 #define CONFIG_SYS_SRIO 46 #define CONFIG_SRIO1 /* SRIO port 1 */ 47 48 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 49 #define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ 50 #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ 51 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 52 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 53 #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ 54 55 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 56 #define CONFIG_ENV_OVERWRITE 57 58 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 59 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 60 #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ 61 62 #define CONFIG_ALTIVEC 1 63 64 /* 65 * L2CR setup -- make sure this is right for your board! 66 */ 67 #define CONFIG_SYS_L2 68 #define L2_INIT 0 69 #define L2_ENABLE (L2CR_L2E) 70 71 #ifndef CONFIG_SYS_CLK_FREQ 72 #ifndef __ASSEMBLY__ 73 extern unsigned long get_board_sys_clk(unsigned long dummy); 74 #endif 75 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 76 #endif 77 78 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 79 #define CONFIG_SYS_MEMTEST_END 0x00400000 80 81 /* 82 * With the exception of PCI Memory and Rapid IO, most devices will simply 83 * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA 84 * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. 85 */ 86 #ifdef CONFIG_PHYS_64BIT 87 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f 88 #else 89 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 90 #endif 91 92 /* 93 * Base addresses -- Note these are effective addresses where the 94 * actual resources get mapped (not physical addresses) 95 */ 96 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 97 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 98 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 99 100 /* Physical addresses */ 101 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 102 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH 103 #define CONFIG_SYS_CCSRBAR_PHYS \ 104 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 105 CONFIG_SYS_CCSRBAR_PHYS_HIGH) 106 107 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ 108 109 /* 110 * DDR Setup 111 */ 112 #define CONFIG_SYS_FSL_DDR2 113 #undef CONFIG_FSL_DDR_INTERACTIVE 114 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 115 #define CONFIG_DDR_SPD 116 117 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 118 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 119 120 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 121 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 122 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 123 #define CONFIG_VERY_BIG_RAM 124 125 #define CONFIG_NUM_DDR_CONTROLLERS 2 126 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 127 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 128 129 /* 130 * I2C addresses of SPD EEPROMs 131 */ 132 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 133 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ 134 #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ 135 #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ 136 137 138 /* 139 * These are used when DDR doesn't use SPD. 140 */ 141 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 142 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 143 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 144 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 145 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 146 #define CONFIG_SYS_DDR_TIMING_1 0x39357322 147 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 148 #define CONFIG_SYS_DDR_MODE_1 0x00480432 149 #define CONFIG_SYS_DDR_MODE_2 0x00000000 150 #define CONFIG_SYS_DDR_INTERVAL 0x06090100 151 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 152 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 153 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 154 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 155 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 156 #define CONFIG_SYS_DDR_CONTROL2 0x04400000 157 158 #define CONFIG_ID_EEPROM 159 #define CONFIG_SYS_I2C_EEPROM_NXID 160 #define CONFIG_ID_EEPROM 161 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 162 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 163 164 #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ 165 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE 166 #define CONFIG_SYS_FLASH_BASE_PHYS \ 167 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 168 CONFIG_SYS_PHYS_ADDR_HIGH) 169 170 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 171 172 #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 173 | 0x00001001) /* port size 16bit */ 174 #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ 175 176 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ 177 | 0x00001001) /* port size 16bit */ 178 #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ 179 180 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ 181 | 0x00000801) /* port size 8bit */ 182 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ 183 184 /* 185 * The LBC_BASE is the base of the region that contains the PIXIS and the CF. 186 * The PIXIS and CF by themselves aren't large enough to take up the 128k 187 * required for the smallest BAT mapping, so there's a 64k hole. 188 */ 189 #define CONFIG_SYS_LBC_BASE 0xffde0000 190 #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE 191 192 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 193 #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) 194 #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) 195 #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ 196 CONFIG_SYS_PHYS_ADDR_HIGH) 197 #define PIXIS_SIZE 0x00008000 /* 32k */ 198 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 199 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 200 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 201 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 202 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ 203 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 204 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 205 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 206 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 207 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 208 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 209 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 210 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 211 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 212 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 213 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 214 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 215 216 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ 217 #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) 218 #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) 219 220 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 221 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 222 223 #undef CONFIG_SYS_FLASH_CHECKSUM 224 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 225 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 226 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 227 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 228 229 #define CONFIG_FLASH_CFI_DRIVER 230 #define CONFIG_SYS_FLASH_CFI 231 #define CONFIG_SYS_FLASH_EMPTY_INFO 232 233 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 234 #define CONFIG_SYS_RAMBOOT 235 #else 236 #undef CONFIG_SYS_RAMBOOT 237 #endif 238 239 #if defined(CONFIG_SYS_RAMBOOT) 240 #undef CONFIG_SPD_EEPROM 241 #define CONFIG_SYS_SDRAM_SIZE 256 242 #endif 243 244 #undef CONFIG_CLOCKS_IN_MHZ 245 246 #define CONFIG_SYS_INIT_RAM_LOCK 1 247 #ifndef CONFIG_SYS_INIT_RAM_LOCK 248 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 249 #else 250 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 251 #endif 252 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 253 254 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 255 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 256 257 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 258 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 259 260 /* Serial Port */ 261 #define CONFIG_CONS_INDEX 1 262 #define CONFIG_SYS_NS16550 263 #define CONFIG_SYS_NS16550_SERIAL 264 #define CONFIG_SYS_NS16550_REG_SIZE 1 265 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 266 267 #define CONFIG_SYS_BAUDRATE_TABLE \ 268 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 269 270 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 271 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 272 273 /* Use the HUSH parser */ 274 #define CONFIG_SYS_HUSH_PARSER 275 276 /* 277 * Pass open firmware flat tree to kernel 278 */ 279 #define CONFIG_OF_LIBFDT 1 280 #define CONFIG_OF_BOARD_SETUP 1 281 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 282 283 /* 284 * I2C 285 */ 286 #define CONFIG_SYS_I2C 287 #define CONFIG_SYS_I2C_FSL 288 #define CONFIG_SYS_FSL_I2C_SPEED 400000 289 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 290 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 291 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 292 293 /* 294 * RapidIO MMU 295 */ 296 #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ 297 #ifdef CONFIG_PHYS_64BIT 298 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 299 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c 300 #else 301 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE 302 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 303 #endif 304 #define CONFIG_SYS_SRIO1_MEM_PHYS \ 305 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 306 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) 307 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 308 309 /* 310 * General PCI 311 * Addresses are mapped 1-1. 312 */ 313 314 #define CONFIG_SYS_PCIE1_NAME "ULI" 315 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 316 #ifdef CONFIG_PHYS_64BIT 317 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 318 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 319 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c 320 #else 321 #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT 322 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT 323 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 324 #endif 325 #define CONFIG_SYS_PCIE1_MEM_PHYS \ 326 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 327 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) 328 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 329 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 330 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 331 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT 332 #define CONFIG_SYS_PCIE1_IO_PHYS \ 333 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 334 CONFIG_SYS_PHYS_ADDR_HIGH) 335 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ 336 337 #ifdef CONFIG_PHYS_64BIT 338 /* 339 * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. 340 * This will increase the amount of PCI address space available for 341 * for mapping RAM. 342 */ 343 #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS 344 #else 345 #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ 346 + CONFIG_SYS_PCIE1_MEM_SIZE) 347 #endif 348 #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ 349 + CONFIG_SYS_PCIE1_MEM_SIZE) 350 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ 351 + CONFIG_SYS_PCIE1_MEM_SIZE) 352 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 353 #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ 354 + CONFIG_SYS_PCIE1_MEM_SIZE) 355 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 356 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 357 #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ 358 + CONFIG_SYS_PCIE1_IO_SIZE) 359 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ 360 + CONFIG_SYS_PCIE1_IO_SIZE) 361 #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ 362 + CONFIG_SYS_PCIE1_IO_SIZE) 363 #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE 364 365 #if defined(CONFIG_PCI) 366 367 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 368 369 #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE 370 371 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 372 373 #define CONFIG_RTL8139 374 375 #undef CONFIG_EEPRO100 376 #undef CONFIG_TULIP 377 378 /************************************************************ 379 * USB support 380 ************************************************************/ 381 #define CONFIG_PCI_OHCI 1 382 #define CONFIG_USB_OHCI_NEW 1 383 #define CONFIG_USB_KEYBOARD 1 384 #define CONFIG_SYS_STDIO_DEREGISTER 385 #define CONFIG_SYS_USB_EVENT_POLL 1 386 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 387 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 388 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 389 390 /*PCIE video card used*/ 391 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 392 393 /*PCI video card used*/ 394 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ 395 396 /* video */ 397 #define CONFIG_VIDEO 398 399 #if defined(CONFIG_VIDEO) 400 #define CONFIG_BIOSEMU 401 #define CONFIG_CFB_CONSOLE 402 #define CONFIG_VIDEO_SW_CURSOR 403 #define CONFIG_VGA_AS_SINGLE_DEVICE 404 #define CONFIG_ATI_RADEON_FB 405 #define CONFIG_VIDEO_LOGO 406 /*#define CONFIG_CONSOLE_CURSOR*/ 407 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT 408 #endif 409 410 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 411 412 #define CONFIG_DOS_PARTITION 413 #define CONFIG_SCSI_AHCI 414 415 #ifdef CONFIG_SCSI_AHCI 416 #define CONFIG_LIBATA 417 #define CONFIG_SATA_ULI5288 418 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 419 #define CONFIG_SYS_SCSI_MAX_LUN 1 420 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 421 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 422 #endif 423 424 #endif /* CONFIG_PCI */ 425 426 #if defined(CONFIG_TSEC_ENET) 427 428 #define CONFIG_MII 1 /* MII PHY management */ 429 430 #define CONFIG_TSEC1 1 431 #define CONFIG_TSEC1_NAME "eTSEC1" 432 #define CONFIG_TSEC2 1 433 #define CONFIG_TSEC2_NAME "eTSEC2" 434 #define CONFIG_TSEC3 1 435 #define CONFIG_TSEC3_NAME "eTSEC3" 436 #define CONFIG_TSEC4 1 437 #define CONFIG_TSEC4_NAME "eTSEC4" 438 439 #define TSEC1_PHY_ADDR 0 440 #define TSEC2_PHY_ADDR 1 441 #define TSEC3_PHY_ADDR 2 442 #define TSEC4_PHY_ADDR 3 443 #define TSEC1_PHYIDX 0 444 #define TSEC2_PHYIDX 0 445 #define TSEC3_PHYIDX 0 446 #define TSEC4_PHYIDX 0 447 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 448 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 449 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 450 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 451 452 #define CONFIG_ETHPRIME "eTSEC1" 453 454 #endif /* CONFIG_TSEC_ENET */ 455 456 457 #ifdef CONFIG_PHYS_64BIT 458 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) 459 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) 460 461 /* Put physical address into the BAT format */ 462 #define BAT_PHYS_ADDR(low, high) \ 463 (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) 464 /* Convert high/low pairs to actual 64-bit value */ 465 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) 466 #else 467 /* 32-bit systems just ignore the "high" bits */ 468 #define BAT_PHYS_ADDR(low, high) (low) 469 #define PAIRED_PHYS_TO_PHYS(low, high) (low) 470 #endif 471 472 /* 473 * BAT0 DDR 474 */ 475 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 476 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 477 478 /* 479 * BAT1 LBC (PIXIS/CF) 480 */ 481 #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 482 CONFIG_SYS_PHYS_ADDR_HIGH) \ 483 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 484 BATL_GUARDEDSTORAGE) 485 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ 486 | BATU_VS | BATU_VP) 487 #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 488 CONFIG_SYS_PHYS_ADDR_HIGH) \ 489 | BATL_PP_RW | BATL_MEMCOHERENCE) 490 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 491 492 /* if CONFIG_PCI: 493 * BAT2 PCIE1 and PCIE1 MEM 494 * if CONFIG_RIO 495 * BAT2 Rapidio Memory 496 */ 497 #ifdef CONFIG_PCI 498 #define CONFIG_PCI_INDIRECT_BRIDGE 499 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 500 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 501 | BATL_PP_RW | BATL_CACHEINHIBIT \ 502 | BATL_GUARDEDSTORAGE) 503 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ 504 | BATU_VS | BATU_VP) 505 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 506 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 507 | BATL_PP_RW | BATL_CACHEINHIBIT) 508 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 509 #else /* CONFIG_RIO */ 510 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 511 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 512 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 513 BATL_GUARDEDSTORAGE) 514 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ 515 | BATU_VS | BATU_VP) 516 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 517 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 518 | BATL_PP_RW | BATL_CACHEINHIBIT) 519 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 520 #endif 521 522 /* 523 * BAT3 CCSR Space 524 */ 525 #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 526 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 527 | BATL_PP_RW | BATL_CACHEINHIBIT \ 528 | BATL_GUARDEDSTORAGE) 529 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ 530 | BATU_VP) 531 #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 532 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 533 | BATL_PP_RW | BATL_CACHEINHIBIT) 534 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 535 536 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 537 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 538 | BATL_PP_RW | BATL_CACHEINHIBIT \ 539 | BATL_GUARDEDSTORAGE) 540 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 541 | BATU_BL_1M | BATU_VS | BATU_VP) 542 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 543 | BATL_PP_RW | BATL_CACHEINHIBIT) 544 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 545 #endif 546 547 /* 548 * BAT4 PCIE1_IO and PCIE2_IO 549 */ 550 #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 551 CONFIG_SYS_PHYS_ADDR_HIGH) \ 552 | BATL_PP_RW | BATL_CACHEINHIBIT \ 553 | BATL_GUARDEDSTORAGE) 554 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ 555 | BATU_VS | BATU_VP) 556 #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 557 CONFIG_SYS_PHYS_ADDR_HIGH) \ 558 | BATL_PP_RW | BATL_CACHEINHIBIT) 559 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 560 561 /* 562 * BAT5 Init RAM for stack in the CPU DCache (no backing memory) 563 */ 564 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 565 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 566 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 567 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 568 569 /* 570 * BAT6 FLASH 571 */ 572 #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 573 CONFIG_SYS_PHYS_ADDR_HIGH) \ 574 | BATL_PP_RW | BATL_CACHEINHIBIT \ 575 | BATL_GUARDEDSTORAGE) 576 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ 577 | BATU_VP) 578 #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 579 CONFIG_SYS_PHYS_ADDR_HIGH) \ 580 | BATL_PP_RW | BATL_MEMCOHERENCE) 581 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 582 583 /* Map the last 1M of flash where we're running from reset */ 584 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 585 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 586 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 587 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 588 | BATL_MEMCOHERENCE) 589 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 590 591 /* 592 * BAT7 FREE - used later for tmp mappings 593 */ 594 #define CONFIG_SYS_DBAT7L 0x00000000 595 #define CONFIG_SYS_DBAT7U 0x00000000 596 #define CONFIG_SYS_IBAT7L 0x00000000 597 #define CONFIG_SYS_IBAT7U 0x00000000 598 599 /* 600 * Environment 601 */ 602 #ifndef CONFIG_SYS_RAMBOOT 603 #define CONFIG_ENV_IS_IN_FLASH 1 604 #define CONFIG_ENV_ADDR \ 605 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 606 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 607 #else 608 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 609 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 610 #endif 611 #define CONFIG_ENV_SIZE 0x2000 612 613 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 614 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 615 616 617 /* 618 * BOOTP options 619 */ 620 #define CONFIG_BOOTP_BOOTFILESIZE 621 #define CONFIG_BOOTP_BOOTPATH 622 #define CONFIG_BOOTP_GATEWAY 623 #define CONFIG_BOOTP_HOSTNAME 624 625 626 /* 627 * Command line configuration. 628 */ 629 #define CONFIG_CMD_PING 630 #define CONFIG_CMD_I2C 631 #define CONFIG_CMD_REGINFO 632 633 #if defined(CONFIG_PCI) 634 #define CONFIG_CMD_PCI 635 #define CONFIG_CMD_SCSI 636 #define CONFIG_CMD_EXT2 637 #define CONFIG_CMD_USB 638 #endif 639 640 641 #undef CONFIG_WATCHDOG /* watchdog disabled */ 642 643 /* 644 * Miscellaneous configurable options 645 */ 646 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 647 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 648 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 649 650 #if defined(CONFIG_CMD_KGDB) 651 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 652 #else 653 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 654 #endif 655 656 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 657 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 658 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 659 660 /* 661 * For booting Linux, the board info and command line data 662 * have to be in the first 8 MB of memory, since this is 663 * the maximum mapped by the Linux kernel during initialization. 664 */ 665 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 666 667 #if defined(CONFIG_CMD_KGDB) 668 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 669 #endif 670 671 /* 672 * Environment Configuration 673 */ 674 675 #define CONFIG_HAS_ETH0 1 676 #define CONFIG_HAS_ETH1 1 677 #define CONFIG_HAS_ETH2 1 678 #define CONFIG_HAS_ETH3 1 679 680 #define CONFIG_IPADDR 192.168.1.100 681 682 #define CONFIG_HOSTNAME unknown 683 #define CONFIG_ROOTPATH "/opt/nfsroot" 684 #define CONFIG_BOOTFILE "uImage" 685 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 686 687 #define CONFIG_SERVERIP 192.168.1.1 688 #define CONFIG_GATEWAYIP 192.168.1.1 689 #define CONFIG_NETMASK 255.255.255.0 690 691 /* default location for tftp and bootm */ 692 #define CONFIG_LOADADDR 1000000 693 694 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 695 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 696 697 #define CONFIG_BAUDRATE 115200 698 699 #define CONFIG_EXTRA_ENV_SETTINGS \ 700 "netdev=eth0\0" \ 701 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 702 "tftpflash=tftpboot $loadaddr $uboot; " \ 703 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 704 " +$filesize; " \ 705 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 706 " +$filesize; " \ 707 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 708 " $filesize; " \ 709 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 710 " +$filesize; " \ 711 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 712 " $filesize\0" \ 713 "consoledev=ttyS0\0" \ 714 "ramdiskaddr=2000000\0" \ 715 "ramdiskfile=your.ramdisk.u-boot\0" \ 716 "fdtaddr=c00000\0" \ 717 "fdtfile=mpc8641_hpcn.dtb\0" \ 718 "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ 719 "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ 720 "maxcpus=2" 721 722 723 #define CONFIG_NFSBOOTCOMMAND \ 724 "setenv bootargs root=/dev/nfs rw " \ 725 "nfsroot=$serverip:$rootpath " \ 726 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 727 "console=$consoledev,$baudrate $othbootargs;" \ 728 "tftp $loadaddr $bootfile;" \ 729 "tftp $fdtaddr $fdtfile;" \ 730 "bootm $loadaddr - $fdtaddr" 731 732 #define CONFIG_RAMBOOTCOMMAND \ 733 "setenv bootargs root=/dev/ram rw " \ 734 "console=$consoledev,$baudrate $othbootargs;" \ 735 "tftp $ramdiskaddr $ramdiskfile;" \ 736 "tftp $loadaddr $bootfile;" \ 737 "tftp $fdtaddr $fdtfile;" \ 738 "bootm $loadaddr $ramdiskaddr $fdtaddr" 739 740 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 741 742 #endif /* __CONFIG_H */ 743