1 /*
2  * Copyright 2007-2011 Freescale Semiconductor, Inc.
3  *
4  * SPDX-License-Identifier:	GPL-2.0
5  */
6 
7 /*
8  * MPC8610HPCD board configuration file
9  */
10 
11 #ifndef __CONFIG_H
12 #define __CONFIG_H
13 
14 /* High Level Configuration Options */
15 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
16 
17 #define	CONFIG_SYS_TEXT_BASE	0xfff00000
18 
19 /* video */
20 #define CONFIG_FSL_DIU_FB
21 
22 #ifdef CONFIG_FSL_DIU_FB
23 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x2c000)
24 #define CONFIG_VIDEO_LOGO
25 #define CONFIG_VIDEO_BMP_LOGO
26 #endif
27 
28 #ifdef RUN_DIAG
29 #define CONFIG_SYS_DIAG_ADDR		0xff800000
30 #endif
31 
32 /*
33  * virtual address to be used for temporary mappings.  There
34  * should be 128k free at this VA.
35  */
36 #define CONFIG_SYS_SCRATCH_VA	0xc0000000
37 
38 #define CONFIG_PCI1		1	/* PCI controller 1 */
39 #define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
40 #define CONFIG_PCIE2		1	/* PCIe 2 connected to slot */
41 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
42 #define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
43 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
44 
45 #define CONFIG_ENV_OVERWRITE
46 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
47 
48 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
49 #define CONFIG_HIGH_BATS	1	/* High BATs supported & enabled */
50 #define CONFIG_ALTIVEC		1
51 
52 /*
53  * L2CR setup -- make sure this is right for your board!
54  */
55 #define CONFIG_SYS_L2
56 #define L2_INIT		0
57 #define L2_ENABLE	(L2CR_L2E |0x00100000 )
58 
59 #ifndef CONFIG_SYS_CLK_FREQ
60 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
61 #endif
62 
63 #define CONFIG_MISC_INIT_R		1
64 
65 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
66 #define CONFIG_SYS_MEMTEST_END		0x00400000
67 
68 /*
69  * Base addresses -- Note these are effective addresses where the
70  * actual resources get mapped (not physical addresses)
71  */
72 #define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
73 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
74 
75 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
76 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
77 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW
78 
79 /* DDR Setup */
80 #undef CONFIG_FSL_DDR_INTERACTIVE
81 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
82 #define CONFIG_DDR_SPD
83 
84 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
85 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
86 
87 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
88 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
89 #define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
90 #define CONFIG_VERY_BIG_RAM
91 
92 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
93 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
94 
95 #define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
96 
97 /* These are used when DDR doesn't use SPD.  */
98 #define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */
99 
100 #if 0 /* TODO */
101 #define CONFIG_SYS_DDR_CS0_BNDS	0x0000000F
102 #define CONFIG_SYS_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
103 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
104 #define CONFIG_SYS_DDR_TIMING_0	0x00260802
105 #define CONFIG_SYS_DDR_TIMING_1	0x3935d322
106 #define CONFIG_SYS_DDR_TIMING_2	0x14904cc8
107 #define CONFIG_SYS_DDR_MODE_1		0x00480432
108 #define CONFIG_SYS_DDR_MODE_2		0x00000000
109 #define CONFIG_SYS_DDR_INTERVAL	0x06180100
110 #define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
111 #define CONFIG_SYS_DDR_CLK_CTRL	0x03800000
112 #define CONFIG_SYS_DDR_OCD_CTRL	0x00000000
113 #define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
114 #define CONFIG_SYS_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
115 #define CONFIG_SYS_DDR_CONTROL2	0x04400010
116 
117 #define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
118 #define CONFIG_SYS_DDR_ERR_DIS		0x00000000
119 #define CONFIG_SYS_DDR_SBE		0x000f0000
120 
121 #endif
122 
123 #define CONFIG_ID_EEPROM
124 #define CONFIG_SYS_I2C_EEPROM_NXID
125 #define CONFIG_ID_EEPROM
126 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
127 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
128 
129 #define CONFIG_SYS_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
130 #define CONFIG_SYS_FLASH_BASE2		0xf8000000
131 
132 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
133 
134 #define CONFIG_SYS_BR0_PRELIM		0xf8001001 /* port size 16bit */
135 #define CONFIG_SYS_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/
136 
137 #define CONFIG_SYS_BR1_PRELIM		0xf0001001 /* port size 16bit */
138 #define CONFIG_SYS_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
139 #if 0 /* TODO */
140 #define CONFIG_SYS_BR2_PRELIM		0xf0000000
141 #define CONFIG_SYS_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
142 #endif
143 #define CONFIG_SYS_BR3_PRELIM		0xe8000801 /* port size 8bit */
144 #define CONFIG_SYS_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
145 
146 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
147 #define PIXIS_BASE	0xe8000000	/* PIXIS registers */
148 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
149 #define PIXIS_VER		0x1	/* Board version at offset 1 */
150 #define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
151 #define PIXIS_RST		0x4	/* PIXIS Reset Control register */
152 #define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch */
153 #define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
154 #define PIXIS_BRDCFG0		0x8	/* PIXIS Board Configuration Register0*/
155 #define PIXIS_VCTL		0x10	/* VELA Control Register */
156 #define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
157 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
158 #define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
159 #define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
160 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
161 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
162 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
163 #define CONFIG_SYS_PIXIS_VBOOT_MASK	0xC0    /* Reset altbank mask */
164 
165 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
166 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
167 
168 #undef	CONFIG_SYS_FLASH_CHECKSUM
169 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
170 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
171 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
172 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */
173 
174 #define CONFIG_FLASH_CFI_DRIVER
175 #define CONFIG_SYS_FLASH_CFI
176 #define CONFIG_SYS_FLASH_EMPTY_INFO
177 
178 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
179 #define CONFIG_SYS_RAMBOOT
180 #else
181 #undef	CONFIG_SYS_RAMBOOT
182 #endif
183 
184 #if defined(CONFIG_SYS_RAMBOOT)
185 #undef CONFIG_SPD_EEPROM
186 #define CONFIG_SYS_SDRAM_SIZE	256
187 #endif
188 
189 #undef CONFIG_CLOCKS_IN_MHZ
190 
191 #define CONFIG_SYS_INIT_RAM_LOCK	1
192 #ifndef CONFIG_SYS_INIT_RAM_LOCK
193 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
194 #else
195 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
196 #endif
197 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
198 
199 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
200 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
201 
202 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
203 #define CONFIG_SYS_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
204 
205 /* Serial Port */
206 #define CONFIG_CONS_INDEX	1
207 #define CONFIG_SYS_NS16550_SERIAL
208 #define CONFIG_SYS_NS16550_REG_SIZE	1
209 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
210 
211 #define CONFIG_SYS_BAUDRATE_TABLE \
212 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
213 
214 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
215 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
216 
217 /* maximum size of the flat tree (8K) */
218 #define OF_FLAT_TREE_MAX_SIZE	8192
219 
220 /*
221  * I2C
222  */
223 #define CONFIG_SYS_I2C
224 #define CONFIG_SYS_I2C_FSL
225 #define CONFIG_SYS_FSL_I2C_SPEED	400000
226 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
227 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
228 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
229 
230 /*
231  * General PCI
232  * Addresses are mapped 1-1.
233  */
234 #define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
235 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
236 #define CONFIG_SYS_PCI1_MEM_VIRT	CONFIG_SYS_PCI1_MEM_BUS
237 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
238 #define CONFIG_SYS_PCI1_IO_BUS	0x0000000
239 #define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
240 #define CONFIG_SYS_PCI1_IO_VIRT	0xe1000000
241 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
242 
243 /* controller 1, Base address 0xa000 */
244 #define CONFIG_SYS_PCIE1_NAME		"ULI"
245 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
246 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
247 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
248 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
249 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe3000000
250 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/* 1M */
251 
252 /* controller 2, Base Address 0x9000 */
253 #define CONFIG_SYS_PCIE2_NAME		"Slot 1"
254 #define CONFIG_SYS_PCIE2_MEM_BUS	0x90000000
255 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
256 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
257 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000	/* reuse mem LAW */
258 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe2000000
259 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00100000	/* 1M */
260 
261 #if defined(CONFIG_PCI)
262 
263 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
264 
265 #define CONFIG_CMD_REGINFO
266 
267 #define CONFIG_ULI526X
268 #ifdef CONFIG_ULI526X
269 #endif
270 
271 /************************************************************
272  * USB support
273  ************************************************************/
274 #define CONFIG_PCI_OHCI		1
275 #define CONFIG_USB_OHCI_NEW		1
276 #define CONFIG_SYS_USB_EVENT_POLL	1
277 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
278 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
279 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1
280 
281 #if !defined(CONFIG_PCI_PNP)
282 #define PCI_ENET0_IOADDR	0xe0000000
283 #define PCI_ENET0_MEMADDR	0xe0000000
284 #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
285 #endif
286 
287 #define CONFIG_SCSI_AHCI
288 
289 #ifdef CONFIG_SCSI_AHCI
290 #define CONFIG_LIBATA
291 #define CONFIG_SATA_ULI5288
292 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
293 #define CONFIG_SYS_SCSI_MAX_LUN	1
294 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
295 #define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
296 #endif
297 
298 #endif	/* CONFIG_PCI */
299 
300 /*
301  * BAT0		2G	Cacheable, non-guarded
302  * 0x0000_0000	2G	DDR
303  */
304 #define CONFIG_SYS_DBAT0L	(BATL_PP_RW)
305 #define CONFIG_SYS_IBAT0L	(BATL_PP_RW)
306 
307 /*
308  * BAT1		1G	Cache-inhibited, guarded
309  * 0x8000_0000	256M	PCI-1 Memory
310  * 0xa000_0000	256M	PCI-Express 1 Memory
311  * 0x9000_0000	256M	PCI-Express 2 Memory
312  */
313 
314 #define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
315 			| BATL_GUARDEDSTORAGE)
316 #define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
317 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
318 #define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
319 
320 /*
321  * BAT2		16M	Cache-inhibited, guarded
322  * 0xe100_0000	1M	PCI-1 I/O
323  */
324 
325 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
326 			| BATL_GUARDEDSTORAGE)
327 #define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
328 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
329 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
330 
331 /*
332  * BAT3		4M	Cache-inhibited, guarded
333  * 0xe000_0000	4M	CCSR
334  */
335 
336 #define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
337 			| BATL_GUARDEDSTORAGE)
338 #define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
339 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
340 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
341 
342 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
343 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
344 				       | BATL_PP_RW | BATL_CACHEINHIBIT \
345 				       | BATL_GUARDEDSTORAGE)
346 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
347 				       | BATU_BL_1M | BATU_VS | BATU_VP)
348 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
349 				       | BATL_PP_RW | BATL_CACHEINHIBIT)
350 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
351 #endif
352 
353 /*
354  * BAT4		32M	Cache-inhibited, guarded
355  * 0xe200_0000	1M	PCI-Express 2 I/O
356  * 0xe300_0000	1M	PCI-Express 1 I/O
357  */
358 
359 #define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
360 			| BATL_GUARDEDSTORAGE)
361 #define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
362 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
363 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
364 
365 /*
366  * BAT5		128K	Cacheable, non-guarded
367  * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
368  */
369 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
370 #define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
371 #define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
372 #define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
373 
374 /*
375  * BAT6		256M	Cache-inhibited, guarded
376  * 0xf000_0000	256M	FLASH
377  */
378 #define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
379 			| BATL_GUARDEDSTORAGE)
380 #define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
381 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
382 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
383 
384 /* Map the last 1M of flash where we're running from reset */
385 #define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
386 				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
387 #define CONFIG_SYS_DBAT6U_EARLY	(CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
388 #define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
389 				 | BATL_MEMCOHERENCE)
390 #define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
391 
392 /*
393  * BAT7		4M	Cache-inhibited, guarded
394  * 0xe800_0000	4M	PIXIS
395  */
396 #define CONFIG_SYS_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
397 			| BATL_GUARDEDSTORAGE)
398 #define CONFIG_SYS_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
399 #define CONFIG_SYS_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
400 #define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U
401 
402 /*
403  * Environment
404  */
405 #ifndef CONFIG_SYS_RAMBOOT
406 #define CONFIG_ENV_IS_IN_FLASH	1
407 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
408 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 126k (one sector) for env */
409 #define CONFIG_ENV_SIZE		0x2000
410 #else
411 #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
412 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
413 #define CONFIG_ENV_SIZE		0x2000
414 #endif
415 
416 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
417 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
418 
419 /*
420  * BOOTP options
421  */
422 #define CONFIG_BOOTP_BOOTFILESIZE
423 #define CONFIG_BOOTP_BOOTPATH
424 #define CONFIG_BOOTP_GATEWAY
425 #define CONFIG_BOOTP_HOSTNAME
426 
427 /*
428  * Command line configuration.
429  */
430 
431 #if defined(CONFIG_PCI)
432 #define CONFIG_CMD_PCI
433 #define CONFIG_SCSI
434 #endif
435 
436 #define CONFIG_WATCHDOG			/* watchdog enabled */
437 #define CONFIG_SYS_WATCHDOG_FREQ	5000	/* Feed interval, 5s */
438 
439 /*
440  * Miscellaneous configurable options
441  */
442 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
443 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
444 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
445 
446 #if defined(CONFIG_CMD_KGDB)
447 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
448 #else
449 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
450 #endif
451 
452 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
453 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
454 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
455 
456 /*
457  * For booting Linux, the board info and command line data
458  * have to be in the first 8 MB of memory, since this is
459  * the maximum mapped by the Linux kernel during initialization.
460  */
461 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Initial Memory map for Linux*/
462 #define CONFIG_SYS_BOOTM_LEN	(256 << 20)	/* Increase max gunzip size */
463 
464 #if defined(CONFIG_CMD_KGDB)
465 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
466 #endif
467 
468 /*
469  * Environment Configuration
470  */
471 #define CONFIG_IPADDR		192.168.1.100
472 
473 #define CONFIG_HOSTNAME		unknown
474 #define CONFIG_ROOTPATH		"/opt/nfsroot"
475 #define CONFIG_BOOTFILE		"uImage"
476 #define CONFIG_UBOOTPATH	8610hpcd/u-boot.bin
477 
478 #define CONFIG_SERVERIP		192.168.1.1
479 #define CONFIG_GATEWAYIP	192.168.1.1
480 #define CONFIG_NETMASK		255.255.255.0
481 
482 /* default location for tftp and bootm */
483 #define CONFIG_LOADADDR		0x10000000
484 
485 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
486 
487 #if defined(CONFIG_PCI1)
488 #define PCI_ENV \
489  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
490 	"echo e;md ${a}e00 9\0" \
491  "pci1regs=setenv a e0008; run pcireg\0" \
492  "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
493 	"pci d.w $b.0 56 1\0" \
494  "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
495 	"pci w.w $b.0 56 ffff\0"	\
496  "pci1err=setenv a e0008; run pcierr\0"	\
497  "pci1errc=setenv a e0008; run pcierrc\0"
498 #else
499 #define	PCI_ENV ""
500 #endif
501 
502 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
503 #define PCIE_ENV \
504  "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
505 	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
506  "pcie1regs=setenv a e000a; run pciereg\0"	\
507  "pcie2regs=setenv a e0009; run pciereg\0"	\
508  "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
509 	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"	\
510 	"pci d $b.0 130 1\0" \
511  "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
512 	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
513 	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"		\
514  "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
515  "pcie1err=setenv a e000a; run pcieerr\0"	\
516  "pcie2err=setenv a e0009; run pcieerr\0"	\
517  "pcie1errc=setenv a e000a; run pcieerrc\0"	\
518  "pcie2errc=setenv a e0009; run pcieerrc\0"
519 #else
520 #define	PCIE_ENV ""
521 #endif
522 
523 #define DMA_ENV \
524  "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
525 	"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
526  "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
527 	"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
528  "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
529 	"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
530  "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
531 	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
532 
533 #ifdef ENV_DEBUG
534 #define	CONFIG_EXTRA_ENV_SETTINGS				\
535 "netdev=eth0\0"							\
536 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
537 "tftpflash=tftpboot $loadaddr $uboot; "				\
538 	"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
539 		" +$filesize; "	\
540 	"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
541 		" +$filesize; "	\
542 	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
543 		" $filesize; "	\
544 	"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
545 		" +$filesize; "	\
546 	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
547 		" $filesize\0"	\
548 "consoledev=ttyS0\0"						\
549 "ramdiskaddr=0x18000000\0"					\
550 "ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
551 "fdtaddr=0x17c00000\0"						\
552 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
553 "bdev=sda3\0"					\
554 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
555 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
556 "maxcpus=1"	\
557 "eoi=mw e00400b0 0\0"						\
558 "iack=md e00400a0 1\0"						\
559 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
560 	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
561 	"md ${a}f00 5\0" \
562 "ddr1regs=setenv a e0002; run ddrreg\0" \
563 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
564 	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
565 	"md ${a}e60 1; md ${a}ef0 1d\0" \
566 "guregs=setenv a e00e0; run gureg\0" \
567 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
568 "mcmregs=setenv a e0001; run mcmreg\0" \
569 "diuregs=md e002c000 1d\0" \
570 "dium=mw e002c01c\0" \
571 "diuerr=md e002c014 1\0" \
572 "pmregs=md e00e1000 2b\0" \
573 "lawregs=md e0000c08 4b\0" \
574 "lbcregs=md e0005000 36\0" \
575 "dma0regs=md e0021100 12\0" \
576 "dma1regs=md e0021180 12\0" \
577 "dma2regs=md e0021200 12\0" \
578 "dma3regs=md e0021280 12\0" \
579  PCI_ENV \
580  PCIE_ENV \
581  DMA_ENV
582 #else
583 #define CONFIG_EXTRA_ENV_SETTINGS				\
584 	"netdev=eth0\0"						\
585 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
586 	"consoledev=ttyS0\0"					\
587 	"ramdiskaddr=0x18000000\0"				\
588 	"ramdiskfile=8610hpcd/ramdisk.uboot\0"			\
589 	"fdtaddr=0x17c00000\0"					\
590 	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"			\
591 	"bdev=sda3\0"
592 #endif
593 
594 #define CONFIG_NFSBOOTCOMMAND					\
595  "setenv bootargs root=/dev/nfs rw "				\
596 	"nfsroot=$serverip:$rootpath "				\
597 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
598 	"console=$consoledev,$baudrate $othbootargs;"		\
599  "tftp $loadaddr $bootfile;"					\
600  "tftp $fdtaddr $fdtfile;"					\
601  "bootm $loadaddr - $fdtaddr"
602 
603 #define CONFIG_RAMBOOTCOMMAND \
604  "setenv bootargs root=/dev/ram rw "				\
605 	"console=$consoledev,$baudrate $othbootargs;"		\
606  "tftp $ramdiskaddr $ramdiskfile;"				\
607  "tftp $loadaddr $bootfile;"					\
608  "tftp $fdtaddr $fdtfile;"					\
609  "bootm $loadaddr $ramdiskaddr $fdtaddr"
610 
611 #define CONFIG_BOOTCOMMAND		\
612  "setenv bootargs root=/dev/$bdev rw "	\
613 	"console=$consoledev,$baudrate $othbootargs;"	\
614  "tftp $loadaddr $bootfile;"		\
615  "tftp $fdtaddr $fdtfile;"		\
616  "bootm $loadaddr - $fdtaddr"
617 
618 #endif	/* __CONFIG_H */
619