1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* 3 * Copyright 2007-2011 Freescale Semiconductor, Inc. 4 */ 5 6 /* 7 * MPC8610HPCD board configuration file 8 */ 9 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* High Level Configuration Options */ 14 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 15 16 /* video */ 17 #define CONFIG_FSL_DIU_FB 18 19 #ifdef CONFIG_FSL_DIU_FB 20 #define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x2c000) 21 #define CONFIG_VIDEO_LOGO 22 #define CONFIG_VIDEO_BMP_LOGO 23 #endif 24 25 #ifdef RUN_DIAG 26 #define CONFIG_SYS_DIAG_ADDR 0xff800000 27 #endif 28 29 /* 30 * virtual address to be used for temporary mappings. There 31 * should be 128k free at this VA. 32 */ 33 #define CONFIG_SYS_SCRATCH_VA 0xc0000000 34 35 #define CONFIG_PCI1 1 /* PCI controller 1 */ 36 #define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */ 37 #define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */ 38 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 39 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 40 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 41 42 #define CONFIG_ENV_OVERWRITE 43 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 44 45 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 46 #define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */ 47 #define CONFIG_ALTIVEC 1 48 49 /* 50 * L2CR setup -- make sure this is right for your board! 51 */ 52 #define CONFIG_SYS_L2 53 #define L2_INIT 0 54 #define L2_ENABLE (L2CR_L2E |0x00100000 ) 55 56 #ifndef CONFIG_SYS_CLK_FREQ 57 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 58 #endif 59 60 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 61 #define CONFIG_SYS_MEMTEST_END 0x00400000 62 63 /* 64 * Base addresses -- Note these are effective addresses where the 65 * actual resources get mapped (not physical addresses) 66 */ 67 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 68 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 69 70 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 71 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 72 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW 73 74 /* DDR Setup */ 75 #undef CONFIG_FSL_DDR_INTERACTIVE 76 #define CONFIG_SPD_EEPROM /* Use SPD for DDR */ 77 #define CONFIG_DDR_SPD 78 79 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 80 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 81 82 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 83 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 84 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 85 #define CONFIG_VERY_BIG_RAM 86 87 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 88 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 89 90 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 91 92 /* These are used when DDR doesn't use SPD. */ 93 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 94 95 #if 0 /* TODO */ 96 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 97 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */ 98 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 99 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 100 #define CONFIG_SYS_DDR_TIMING_1 0x3935d322 101 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 102 #define CONFIG_SYS_DDR_MODE_1 0x00480432 103 #define CONFIG_SYS_DDR_MODE_2 0x00000000 104 #define CONFIG_SYS_DDR_INTERVAL 0x06180100 105 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 106 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 107 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 108 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 109 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 110 #define CONFIG_SYS_DDR_CONTROL2 0x04400010 111 112 #define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000 113 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 114 #define CONFIG_SYS_DDR_SBE 0x000f0000 115 116 #endif 117 118 #define CONFIG_ID_EEPROM 119 #define CONFIG_SYS_I2C_EEPROM_NXID 120 #define CONFIG_ID_EEPROM 121 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 122 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 123 124 #define CONFIG_SYS_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ 125 #define CONFIG_SYS_FLASH_BASE2 0xf8000000 126 127 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 128 129 #define CONFIG_SYS_BR0_PRELIM 0xf8001001 /* port size 16bit */ 130 #define CONFIG_SYS_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/ 131 132 #define CONFIG_SYS_BR1_PRELIM 0xf0001001 /* port size 16bit */ 133 #define CONFIG_SYS_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */ 134 #if 0 /* TODO */ 135 #define CONFIG_SYS_BR2_PRELIM 0xf0000000 136 #define CONFIG_SYS_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */ 137 #endif 138 #define CONFIG_SYS_BR3_PRELIM 0xe8000801 /* port size 8bit */ 139 #define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ 140 141 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 142 #define PIXIS_BASE 0xe8000000 /* PIXIS registers */ 143 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 144 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 145 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 146 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 147 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */ 148 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 149 #define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/ 150 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 151 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 152 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 153 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 154 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 155 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 156 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 157 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 158 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0xC0 /* Reset altbank mask */ 159 160 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 161 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 162 163 #undef CONFIG_SYS_FLASH_CHECKSUM 164 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 165 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 166 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 167 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 168 169 #define CONFIG_SYS_FLASH_EMPTY_INFO 170 171 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 172 #define CONFIG_SYS_RAMBOOT 173 #else 174 #undef CONFIG_SYS_RAMBOOT 175 #endif 176 177 #if defined(CONFIG_SYS_RAMBOOT) 178 #undef CONFIG_SPD_EEPROM 179 #define CONFIG_SYS_SDRAM_SIZE 256 180 #endif 181 182 #undef CONFIG_CLOCKS_IN_MHZ 183 184 #define CONFIG_SYS_INIT_RAM_LOCK 1 185 #ifndef CONFIG_SYS_INIT_RAM_LOCK 186 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 187 #else 188 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */ 189 #endif 190 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 191 192 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 193 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 194 195 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 196 #define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ 197 198 /* Serial Port */ 199 #define CONFIG_SYS_NS16550_SERIAL 200 #define CONFIG_SYS_NS16550_REG_SIZE 1 201 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 202 203 #define CONFIG_SYS_BAUDRATE_TABLE \ 204 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 205 206 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 207 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 208 209 /* maximum size of the flat tree (8K) */ 210 #define OF_FLAT_TREE_MAX_SIZE 8192 211 212 /* 213 * I2C 214 */ 215 #define CONFIG_SYS_I2C 216 #define CONFIG_SYS_I2C_FSL 217 #define CONFIG_SYS_FSL_I2C_SPEED 400000 218 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 219 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 220 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 221 222 /* 223 * General PCI 224 * Addresses are mapped 1-1. 225 */ 226 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 227 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS 228 #define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS 229 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 230 #define CONFIG_SYS_PCI1_IO_BUS 0x0000000 231 #define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 232 #define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 233 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 234 235 /* controller 1, Base address 0xa000 */ 236 #define CONFIG_SYS_PCIE1_NAME "ULI" 237 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 238 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 239 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ 240 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 241 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000 242 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */ 243 244 /* controller 2, Base Address 0x9000 */ 245 #define CONFIG_SYS_PCIE2_NAME "Slot 1" 246 #define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000 247 #define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BUS 248 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */ 249 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 /* reuse mem LAW */ 250 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe2000000 251 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00100000 /* 1M */ 252 253 #if defined(CONFIG_PCI) 254 255 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 256 257 #define CONFIG_ULI526X 258 259 /************************************************************ 260 * USB support 261 ************************************************************/ 262 #define CONFIG_PCI_OHCI 1 263 #define CONFIG_USB_OHCI_NEW 1 264 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 265 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 266 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 267 268 #if !defined(CONFIG_PCI_PNP) 269 #define PCI_ENET0_IOADDR 0xe0000000 270 #define PCI_ENET0_MEMADDR 0xe0000000 271 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 272 #endif 273 274 #ifdef CONFIG_SCSI_AHCI 275 #define CONFIG_SATA_ULI5288 276 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 277 #define CONFIG_SYS_SCSI_MAX_LUN 1 278 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 279 #endif 280 281 #endif /* CONFIG_PCI */ 282 283 /* 284 * BAT0 2G Cacheable, non-guarded 285 * 0x0000_0000 2G DDR 286 */ 287 #define CONFIG_SYS_DBAT0L (BATL_PP_RW) 288 #define CONFIG_SYS_IBAT0L (BATL_PP_RW) 289 290 /* 291 * BAT1 1G Cache-inhibited, guarded 292 * 0x8000_0000 256M PCI-1 Memory 293 * 0xa000_0000 256M PCI-Express 1 Memory 294 * 0x9000_0000 256M PCI-Express 2 Memory 295 */ 296 297 #define CONFIG_SYS_DBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 298 | BATL_GUARDEDSTORAGE) 299 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP) 300 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 301 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 302 303 /* 304 * BAT2 16M Cache-inhibited, guarded 305 * 0xe100_0000 1M PCI-1 I/O 306 */ 307 308 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 309 | BATL_GUARDEDSTORAGE) 310 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP) 311 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 312 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 313 314 /* 315 * BAT3 4M Cache-inhibited, guarded 316 * 0xe000_0000 4M CCSR 317 */ 318 319 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \ 320 | BATL_GUARDEDSTORAGE) 321 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP) 322 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) 323 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 324 325 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 326 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 327 | BATL_PP_RW | BATL_CACHEINHIBIT \ 328 | BATL_GUARDEDSTORAGE) 329 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 330 | BATU_BL_1M | BATU_VS | BATU_VP) 331 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 332 | BATL_PP_RW | BATL_CACHEINHIBIT) 333 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 334 #endif 335 336 /* 337 * BAT4 32M Cache-inhibited, guarded 338 * 0xe200_0000 1M PCI-Express 2 I/O 339 * 0xe300_0000 1M PCI-Express 1 I/O 340 */ 341 342 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \ 343 | BATL_GUARDEDSTORAGE) 344 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP) 345 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) 346 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 347 348 /* 349 * BAT5 128K Cacheable, non-guarded 350 * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory) 351 */ 352 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 353 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 354 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 355 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 356 357 /* 358 * BAT6 256M Cache-inhibited, guarded 359 * 0xf000_0000 256M FLASH 360 */ 361 #define CONFIG_SYS_DBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ 362 | BATL_GUARDEDSTORAGE) 363 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 364 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE) 365 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 366 367 /* Map the last 1M of flash where we're running from reset */ 368 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 369 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 370 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 371 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 372 | BATL_MEMCOHERENCE) 373 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 374 375 /* 376 * BAT7 4M Cache-inhibited, guarded 377 * 0xe800_0000 4M PIXIS 378 */ 379 #define CONFIG_SYS_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \ 380 | BATL_GUARDEDSTORAGE) 381 #define CONFIG_SYS_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 382 #define CONFIG_SYS_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) 383 #define CONFIG_SYS_IBAT7U CONFIG_SYS_DBAT7U 384 385 /* 386 * Environment 387 */ 388 #ifndef CONFIG_SYS_RAMBOOT 389 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 390 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */ 391 #define CONFIG_ENV_SIZE 0x2000 392 #else 393 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 394 #define CONFIG_ENV_SIZE 0x2000 395 #endif 396 397 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 398 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 399 400 /* 401 * BOOTP options 402 */ 403 #define CONFIG_BOOTP_BOOTFILESIZE 404 405 /* 406 * Command line configuration. 407 */ 408 409 #define CONFIG_WATCHDOG /* watchdog enabled */ 410 #define CONFIG_SYS_WATCHDOG_FREQ 5000 /* Feed interval, 5s */ 411 412 /* 413 * Miscellaneous configurable options 414 */ 415 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 416 417 /* 418 * For booting Linux, the board info and command line data 419 * have to be in the first 8 MB of memory, since this is 420 * the maximum mapped by the Linux kernel during initialization. 421 */ 422 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ 423 #define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */ 424 425 #if defined(CONFIG_CMD_KGDB) 426 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 427 #endif 428 429 /* 430 * Environment Configuration 431 */ 432 #define CONFIG_IPADDR 192.168.1.100 433 434 #define CONFIG_HOSTNAME "unknown" 435 #define CONFIG_ROOTPATH "/opt/nfsroot" 436 #define CONFIG_BOOTFILE "uImage" 437 #define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin 438 439 #define CONFIG_SERVERIP 192.168.1.1 440 #define CONFIG_GATEWAYIP 192.168.1.1 441 #define CONFIG_NETMASK 255.255.255.0 442 443 /* default location for tftp and bootm */ 444 #define CONFIG_LOADADDR 0x10000000 445 446 #if defined(CONFIG_PCI1) 447 #define PCI_ENV \ 448 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \ 449 "echo e;md ${a}e00 9\0" \ 450 "pci1regs=setenv a e0008; run pcireg\0" \ 451 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \ 452 "pci d.w $b.0 56 1\0" \ 453 "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \ 454 "pci w.w $b.0 56 ffff\0" \ 455 "pci1err=setenv a e0008; run pcierr\0" \ 456 "pci1errc=setenv a e0008; run pcierrc\0" 457 #else 458 #define PCI_ENV "" 459 #endif 460 461 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) 462 #define PCIE_ENV \ 463 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \ 464 "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \ 465 "pcie1regs=setenv a e000a; run pciereg\0" \ 466 "pcie2regs=setenv a e0009; run pciereg\0" \ 467 "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\ 468 "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \ 469 "pci d $b.0 130 1\0" \ 470 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\ 471 "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \ 472 "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \ 473 "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \ 474 "pcie1err=setenv a e000a; run pcieerr\0" \ 475 "pcie2err=setenv a e0009; run pcieerr\0" \ 476 "pcie1errc=setenv a e000a; run pcieerrc\0" \ 477 "pcie2errc=setenv a e0009; run pcieerrc\0" 478 #else 479 #define PCIE_ENV "" 480 #endif 481 482 #define DMA_ENV \ 483 "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\ 484 "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \ 485 "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\ 486 "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \ 487 "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\ 488 "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \ 489 "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\ 490 "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0" 491 492 #ifdef ENV_DEBUG 493 #define CONFIG_EXTRA_ENV_SETTINGS \ 494 "netdev=eth0\0" \ 495 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 496 "tftpflash=tftpboot $loadaddr $uboot; " \ 497 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 498 " +$filesize; " \ 499 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 500 " +$filesize; " \ 501 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 502 " $filesize; " \ 503 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 504 " +$filesize; " \ 505 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 506 " $filesize\0" \ 507 "consoledev=ttyS0\0" \ 508 "ramdiskaddr=0x18000000\0" \ 509 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ 510 "fdtaddr=0x17c00000\0" \ 511 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ 512 "bdev=sda3\0" \ 513 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \ 514 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \ 515 "maxcpus=1" \ 516 "eoi=mw e00400b0 0\0" \ 517 "iack=md e00400a0 1\0" \ 518 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \ 519 "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \ 520 "md ${a}f00 5\0" \ 521 "ddr1regs=setenv a e0002; run ddrreg\0" \ 522 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \ 523 "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \ 524 "md ${a}e60 1; md ${a}ef0 1d\0" \ 525 "guregs=setenv a e00e0; run gureg\0" \ 526 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \ 527 "mcmregs=setenv a e0001; run mcmreg\0" \ 528 "diuregs=md e002c000 1d\0" \ 529 "dium=mw e002c01c\0" \ 530 "diuerr=md e002c014 1\0" \ 531 "pmregs=md e00e1000 2b\0" \ 532 "lawregs=md e0000c08 4b\0" \ 533 "lbcregs=md e0005000 36\0" \ 534 "dma0regs=md e0021100 12\0" \ 535 "dma1regs=md e0021180 12\0" \ 536 "dma2regs=md e0021200 12\0" \ 537 "dma3regs=md e0021280 12\0" \ 538 PCI_ENV \ 539 PCIE_ENV \ 540 DMA_ENV 541 #else 542 #define CONFIG_EXTRA_ENV_SETTINGS \ 543 "netdev=eth0\0" \ 544 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 545 "consoledev=ttyS0\0" \ 546 "ramdiskaddr=0x18000000\0" \ 547 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \ 548 "fdtaddr=0x17c00000\0" \ 549 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \ 550 "bdev=sda3\0" 551 #endif 552 553 #define CONFIG_NFSBOOTCOMMAND \ 554 "setenv bootargs root=/dev/nfs rw " \ 555 "nfsroot=$serverip:$rootpath " \ 556 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 557 "console=$consoledev,$baudrate $othbootargs;" \ 558 "tftp $loadaddr $bootfile;" \ 559 "tftp $fdtaddr $fdtfile;" \ 560 "bootm $loadaddr - $fdtaddr" 561 562 #define CONFIG_RAMBOOTCOMMAND \ 563 "setenv bootargs root=/dev/ram rw " \ 564 "console=$consoledev,$baudrate $othbootargs;" \ 565 "tftp $ramdiskaddr $ramdiskfile;" \ 566 "tftp $loadaddr $bootfile;" \ 567 "tftp $fdtaddr $fdtfile;" \ 568 "bootm $loadaddr $ramdiskaddr $fdtaddr" 569 570 #define CONFIG_BOOTCOMMAND \ 571 "setenv bootargs root=/dev/$bdev rw " \ 572 "console=$consoledev,$baudrate $othbootargs;" \ 573 "tftp $loadaddr $bootfile;" \ 574 "tftp $fdtaddr $fdtfile;" \ 575 "bootm $loadaddr - $fdtaddr" 576 577 #endif /* __CONFIG_H */ 578