1 /*
2  * Copyright 2007-2011 Freescale Semiconductor, Inc.
3  *
4  * This program is free software; you can redistribute it and/or
5  * modify it under the terms of the GNU General Public License
6  * Version 2 as published by the Free Software Foundation.
7  */
8 
9 /*
10  * MPC8610HPCD board configuration file
11  */
12 
13 #ifndef __CONFIG_H
14 #define __CONFIG_H
15 
16 /* High Level Configuration Options */
17 #define CONFIG_MPC86xx		1	/* MPC86xx */
18 #define CONFIG_MPC8610		1	/* MPC8610 specific */
19 #define CONFIG_MPC8610HPCD	1	/* MPC8610HPCD board specific */
20 #define CONFIG_LINUX_RESET_VEC	0x100	/* Reset vector used by Linux */
21 
22 #define	CONFIG_SYS_TEXT_BASE	0xfff00000
23 
24 
25 /* video */
26 #define CONFIG_FSL_DIU_FB
27 
28 #ifdef CONFIG_FSL_DIU_FB
29 #define CONFIG_SYS_DIU_ADDR	(CONFIG_SYS_CCSRBAR + 0x2c000)
30 #define CONFIG_VIDEO
31 #define CONFIG_CMD_BMP
32 #define CONFIG_CFB_CONSOLE
33 #define CONFIG_VIDEO_SW_CURSOR
34 #define CONFIG_VGA_AS_SINGLE_DEVICE
35 #define CONFIG_VIDEO_LOGO
36 #define CONFIG_VIDEO_BMP_LOGO
37 #endif
38 
39 #ifdef RUN_DIAG
40 #define CONFIG_SYS_DIAG_ADDR		0xff800000
41 #endif
42 
43 /*
44  * virtual address to be used for temporary mappings.  There
45  * should be 128k free at this VA.
46  */
47 #define CONFIG_SYS_SCRATCH_VA	0xc0000000
48 
49 #define CONFIG_PCI		1	/* Enable PCI/PCIE*/
50 #define CONFIG_PCI1		1	/* PCI controler 1 */
51 #define CONFIG_PCIE1		1	/* PCIe 1 connected to ULI bridge */
52 #define CONFIG_PCIE2		1	/* PCIe 2 connected to slot */
53 #define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
54 #define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
55 #define CONFIG_FSL_LAW		1	/* Use common FSL init code */
56 
57 #define CONFIG_ENV_OVERWRITE
58 #define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
59 
60 #define CONFIG_BAT_RW		1	/* Use common BAT rw code */
61 #define CONFIG_HIGH_BATS	1	/* High BATs supported & enabled */
62 #define CONFIG_ALTIVEC		1
63 
64 /*
65  * L2CR setup -- make sure this is right for your board!
66  */
67 #define CONFIG_SYS_L2
68 #define L2_INIT		0
69 #define L2_ENABLE	(L2CR_L2E |0x00100000 )
70 
71 #ifndef CONFIG_SYS_CLK_FREQ
72 #define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
73 #endif
74 
75 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
76 #define CONFIG_MISC_INIT_R		1
77 
78 #define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest region */
79 #define CONFIG_SYS_MEMTEST_END		0x00400000
80 
81 /*
82  * Base addresses -- Note these are effective addresses where the
83  * actual resources get mapped (not physical addresses)
84  */
85 #define CONFIG_SYS_CCSRBAR_DEFAULT	0xff700000	/* CCSRBAR Default */
86 #define CONFIG_SYS_CCSRBAR		0xe0000000	/* relocated CCSRBAR */
87 #define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
88 
89 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
90 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH	0x0
91 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW
92 
93 /* DDR Setup */
94 #define CONFIG_FSL_DDR2
95 #undef CONFIG_FSL_DDR_INTERACTIVE
96 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
97 #define CONFIG_DDR_SPD
98 
99 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
100 #define CONFIG_MEM_INIT_VALUE	0xDeadBeef
101 
102 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory*/
103 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
104 #define CONFIG_SYS_MAX_DDR_BAT_SIZE	0x80000000	/* BAT mapping size */
105 #define CONFIG_VERY_BIG_RAM
106 
107 #define CONFIG_NUM_DDR_CONTROLLERS	1
108 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
109 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
110 
111 #define SPD_EEPROM_ADDRESS	0x51	/* CTLR 0 DIMM 0 */
112 
113 /* These are used when DDR doesn't use SPD.  */
114 #define CONFIG_SYS_SDRAM_SIZE	256		/* DDR is 256MB */
115 
116 #if 0 /* TODO */
117 #define CONFIG_SYS_DDR_CS0_BNDS	0x0000000F
118 #define CONFIG_SYS_DDR_CS0_CONFIG	0x80010202	/* Enable, no interleaving */
119 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
120 #define CONFIG_SYS_DDR_TIMING_0	0x00260802
121 #define CONFIG_SYS_DDR_TIMING_1	0x3935d322
122 #define CONFIG_SYS_DDR_TIMING_2	0x14904cc8
123 #define CONFIG_SYS_DDR_MODE_1		0x00480432
124 #define CONFIG_SYS_DDR_MODE_2		0x00000000
125 #define CONFIG_SYS_DDR_INTERVAL	0x06180100
126 #define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
127 #define CONFIG_SYS_DDR_CLK_CTRL	0x03800000
128 #define CONFIG_SYS_DDR_OCD_CTRL	0x00000000
129 #define CONFIG_SYS_DDR_OCD_STATUS	0x00000000
130 #define CONFIG_SYS_DDR_CONTROL		0xe3008000	/* Type = DDR2 */
131 #define CONFIG_SYS_DDR_CONTROL2	0x04400010
132 
133 #define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
134 #define CONFIG_SYS_DDR_ERR_DIS		0x00000000
135 #define CONFIG_SYS_DDR_SBE		0x000f0000
136 
137 #endif
138 
139 
140 #define CONFIG_ID_EEPROM
141 #define CONFIG_SYS_I2C_EEPROM_NXID
142 #define CONFIG_ID_EEPROM
143 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
144 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
145 
146 
147 #define CONFIG_SYS_FLASH_BASE		0xf0000000 /* start of FLASH 128M */
148 #define CONFIG_SYS_FLASH_BASE2		0xf8000000
149 
150 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
151 
152 #define CONFIG_SYS_BR0_PRELIM		0xf8001001 /* port size 16bit */
153 #define CONFIG_SYS_OR0_PRELIM		0xf8006e65 /* 128MB NOR Flash*/
154 
155 #define CONFIG_SYS_BR1_PRELIM		0xf0001001 /* port size 16bit */
156 #define CONFIG_SYS_OR1_PRELIM		0xf8006e65 /* 128MB Promjet */
157 #if 0 /* TODO */
158 #define CONFIG_SYS_BR2_PRELIM		0xf0000000
159 #define CONFIG_SYS_OR2_PRELIM		0xf0000000 /* 256MB NAND Flash - bank 1 */
160 #endif
161 #define CONFIG_SYS_BR3_PRELIM		0xe8000801 /* port size 8bit */
162 #define CONFIG_SYS_OR3_PRELIM		0xfff06ff7 /* 1MB PIXIS area*/
163 
164 
165 #define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
166 #define PIXIS_BASE	0xe8000000	/* PIXIS registers */
167 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
168 #define PIXIS_VER		0x1	/* Board version at offset 1 */
169 #define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
170 #define PIXIS_RST		0x4	/* PIXIS Reset Control register */
171 #define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch */
172 #define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
173 #define PIXIS_BRDCFG0		0x8	/* PIXIS Board Configuration Register0*/
174 #define PIXIS_VCTL		0x10	/* VELA Control Register */
175 #define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
176 #define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
177 #define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
178 #define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
179 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
180 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
181 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
182 #define CONFIG_SYS_PIXIS_VBOOT_MASK	0xC0    /* Reset altbank mask */
183 
184 #define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
185 #define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
186 
187 #undef	CONFIG_SYS_FLASH_CHECKSUM
188 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
189 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
190 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
191 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000	/* early monitor loc */
192 
193 #define CONFIG_FLASH_CFI_DRIVER
194 #define CONFIG_SYS_FLASH_CFI
195 #define CONFIG_SYS_FLASH_EMPTY_INFO
196 
197 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
198 #define CONFIG_SYS_RAMBOOT
199 #else
200 #undef	CONFIG_SYS_RAMBOOT
201 #endif
202 
203 #if defined(CONFIG_SYS_RAMBOOT)
204 #undef CONFIG_SPD_EEPROM
205 #define CONFIG_SYS_SDRAM_SIZE	256
206 #endif
207 
208 #undef CONFIG_CLOCKS_IN_MHZ
209 
210 #define CONFIG_SYS_INIT_RAM_LOCK	1
211 #ifndef CONFIG_SYS_INIT_RAM_LOCK
212 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4010000	/* Initial RAM address */
213 #else
214 #define CONFIG_SYS_INIT_RAM_ADDR	0xe4000000	/* Initial RAM address */
215 #endif
216 #define CONFIG_SYS_INIT_RAM_SIZE	0x4000		/* Size of used area in RAM */
217 
218 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
219 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
220 
221 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)	/* Reserve 512 KB for Mon */
222 #define CONFIG_SYS_MALLOC_LEN		(6 * 1024 * 1024)	/* Reserved for malloc */
223 
224 /* Serial Port */
225 #define CONFIG_CONS_INDEX	1
226 #define CONFIG_SYS_NS16550
227 #define CONFIG_SYS_NS16550_SERIAL
228 #define CONFIG_SYS_NS16550_REG_SIZE	1
229 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
230 
231 #define CONFIG_SYS_BAUDRATE_TABLE \
232 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
233 
234 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
235 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
236 
237 /* Use the HUSH parser */
238 #define CONFIG_SYS_HUSH_PARSER
239 
240 /*
241  * Pass open firmware flat tree to kernel
242  */
243 #define CONFIG_OF_LIBFDT		1
244 #define CONFIG_OF_BOARD_SETUP		1
245 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
246 
247 
248 /* maximum size of the flat tree (8K) */
249 #define OF_FLAT_TREE_MAX_SIZE	8192
250 
251 /*
252  * I2C
253  */
254 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
255 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
256 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
257 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
258 #define CONFIG_SYS_I2C_SLAVE		0x7F
259 #define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
260 #define CONFIG_SYS_I2C_OFFSET		0x3000
261 
262 /*
263  * General PCI
264  * Addresses are mapped 1-1.
265  */
266 #define CONFIG_SYS_PCI1_MEM_BUS		0x80000000
267 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BUS
268 #define CONFIG_SYS_PCI1_MEM_VIRT	CONFIG_SYS_PCI1_MEM_BUS
269 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
270 #define CONFIG_SYS_PCI1_IO_BUS	0x0000000
271 #define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
272 #define CONFIG_SYS_PCI1_IO_VIRT	0xe1000000
273 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
274 
275 /* controller 1, Base address 0xa000 */
276 #define CONFIG_SYS_PCIE1_NAME		"ULI"
277 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
278 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
279 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
280 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
281 #define CONFIG_SYS_PCIE1_IO_PHYS	0xe3000000
282 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00100000	/* 1M */
283 
284 /* controller 2, Base Address 0x9000 */
285 #define CONFIG_SYS_PCIE2_NAME		"Slot 1"
286 #define CONFIG_SYS_PCIE2_MEM_BUS	0x90000000
287 #define CONFIG_SYS_PCIE2_MEM_PHYS	CONFIG_SYS_PCIE2_MEM_BUS
288 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
289 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000	/* reuse mem LAW */
290 #define CONFIG_SYS_PCIE2_IO_PHYS	0xe2000000
291 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00100000	/* 1M */
292 
293 
294 #if defined(CONFIG_PCI)
295 
296 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
297 
298 #define CONFIG_CMD_NET
299 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
300 #define CONFIG_CMD_REGINFO
301 
302 #define CONFIG_ULI526X
303 #ifdef CONFIG_ULI526X
304 #define CONFIG_ETHADDR   00:E0:0C:00:00:01
305 #endif
306 
307 /************************************************************
308  * USB support
309  ************************************************************/
310 #define CONFIG_PCI_OHCI		1
311 #define CONFIG_USB_OHCI_NEW		1
312 #define CONFIG_USB_KEYBOARD	1
313 #define CONFIG_SYS_STDIO_DEREGISTER
314 #define CONFIG_SYS_USB_EVENT_POLL	1
315 #define CONFIG_SYS_USB_OHCI_SLOT_NAME	"ohci_pci"
316 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
317 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS	1
318 
319 #if !defined(CONFIG_PCI_PNP)
320 #define PCI_ENET0_IOADDR	0xe0000000
321 #define PCI_ENET0_MEMADDR	0xe0000000
322 #define PCI_IDSEL_NUMBER	0x0c	/* slot0->3(IDSEL)=12->15 */
323 #endif
324 
325 #define CONFIG_DOS_PARTITION
326 #define CONFIG_SCSI_AHCI
327 
328 #ifdef CONFIG_SCSI_AHCI
329 #define CONFIG_SATA_ULI5288
330 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
331 #define CONFIG_SYS_SCSI_MAX_LUN	1
332 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
333 #define CONFIG_SYS_SCSI_MAXDEVICE	CONFIG_SYS_SCSI_MAX_DEVICE
334 #endif
335 
336 #endif	/* CONFIG_PCI */
337 
338 /*
339  * BAT0		2G	Cacheable, non-guarded
340  * 0x0000_0000	2G	DDR
341  */
342 #define CONFIG_SYS_DBAT0L	(BATL_PP_RW)
343 #define CONFIG_SYS_IBAT0L	(BATL_PP_RW)
344 
345 /*
346  * BAT1		1G	Cache-inhibited, guarded
347  * 0x8000_0000	256M	PCI-1 Memory
348  * 0xa000_0000	256M	PCI-Express 1 Memory
349  * 0x9000_0000	256M	PCI-Express 2 Memory
350  */
351 
352 #define CONFIG_SYS_DBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
353 			| BATL_GUARDEDSTORAGE)
354 #define CONFIG_SYS_DBAT1U	(CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
355 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
356 #define CONFIG_SYS_IBAT1U	CONFIG_SYS_DBAT1U
357 
358 /*
359  * BAT2		16M	Cache-inhibited, guarded
360  * 0xe100_0000	1M	PCI-1 I/O
361  */
362 
363 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
364 			| BATL_GUARDEDSTORAGE)
365 #define CONFIG_SYS_DBAT2U	(CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
366 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
367 #define CONFIG_SYS_IBAT2U	CONFIG_SYS_DBAT2U
368 
369 /*
370  * BAT3		4M	Cache-inhibited, guarded
371  * 0xe000_0000	4M	CCSR
372  */
373 
374 #define CONFIG_SYS_DBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
375 			| BATL_GUARDEDSTORAGE)
376 #define CONFIG_SYS_DBAT3U	(CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
377 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
378 #define CONFIG_SYS_IBAT3U	CONFIG_SYS_DBAT3U
379 
380 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
381 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
382 				       | BATL_PP_RW | BATL_CACHEINHIBIT \
383 				       | BATL_GUARDEDSTORAGE)
384 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
385 				       | BATU_BL_1M | BATU_VS | BATU_VP)
386 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
387 				       | BATL_PP_RW | BATL_CACHEINHIBIT)
388 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
389 #endif
390 
391 /*
392  * BAT4		32M	Cache-inhibited, guarded
393  * 0xe200_0000	1M	PCI-Express 2 I/O
394  * 0xe300_0000	1M	PCI-Express 1 I/O
395  */
396 
397 #define CONFIG_SYS_DBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
398 			| BATL_GUARDEDSTORAGE)
399 #define CONFIG_SYS_DBAT4U	(CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
400 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
401 #define CONFIG_SYS_IBAT4U	CONFIG_SYS_DBAT4U
402 
403 
404 /*
405  * BAT5		128K	Cacheable, non-guarded
406  * 0xe400_0000	128K	Init RAM for stack in the CPU DCache (no backing memory)
407  */
408 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
409 #define CONFIG_SYS_DBAT5U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
410 #define CONFIG_SYS_IBAT5L	CONFIG_SYS_DBAT5L
411 #define CONFIG_SYS_IBAT5U	CONFIG_SYS_DBAT5U
412 
413 /*
414  * BAT6		256M	Cache-inhibited, guarded
415  * 0xf000_0000	256M	FLASH
416  */
417 #define CONFIG_SYS_DBAT6L	(CONFIG_SYS_FLASH_BASE	 | BATL_PP_RW | BATL_CACHEINHIBIT \
418 			| BATL_GUARDEDSTORAGE)
419 #define CONFIG_SYS_DBAT6U	(CONFIG_SYS_FLASH_BASE	 | BATU_BL_256M | BATU_VS | BATU_VP)
420 #define CONFIG_SYS_IBAT6L	(CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
421 #define CONFIG_SYS_IBAT6U	CONFIG_SYS_DBAT6U
422 
423 /* Map the last 1M of flash where we're running from reset */
424 #define CONFIG_SYS_DBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
425 				 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
426 #define CONFIG_SYS_DBAT6U_EARLY	(CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
427 #define CONFIG_SYS_IBAT6L_EARLY	(CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
428 				 | BATL_MEMCOHERENCE)
429 #define CONFIG_SYS_IBAT6U_EARLY	CONFIG_SYS_DBAT6U_EARLY
430 
431 /*
432  * BAT7		4M	Cache-inhibited, guarded
433  * 0xe800_0000	4M	PIXIS
434  */
435 #define CONFIG_SYS_DBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
436 			| BATL_GUARDEDSTORAGE)
437 #define CONFIG_SYS_DBAT7U	(PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
438 #define CONFIG_SYS_IBAT7L	(PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
439 #define CONFIG_SYS_IBAT7U	CONFIG_SYS_DBAT7U
440 
441 
442 /*
443  * Environment
444  */
445 #ifndef CONFIG_SYS_RAMBOOT
446 #define CONFIG_ENV_IS_IN_FLASH	1
447 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
448 #define CONFIG_ENV_SECT_SIZE	0x20000	/* 126k (one sector) for env */
449 #define CONFIG_ENV_SIZE		0x2000
450 #else
451 #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
452 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
453 #define CONFIG_ENV_SIZE		0x2000
454 #endif
455 
456 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
457 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
458 
459 
460 /*
461  * BOOTP options
462  */
463 #define CONFIG_BOOTP_BOOTFILESIZE
464 #define CONFIG_BOOTP_BOOTPATH
465 #define CONFIG_BOOTP_GATEWAY
466 #define CONFIG_BOOTP_HOSTNAME
467 
468 
469 /*
470  * Command line configuration.
471  */
472 #include <config_cmd_default.h>
473 
474 #define CONFIG_CMD_PING
475 #define CONFIG_CMD_I2C
476 #define CONFIG_CMD_MII
477 
478 #if defined(CONFIG_SYS_RAMBOOT)
479 #undef CONFIG_CMD_SAVEENV
480 #endif
481 
482 #if defined(CONFIG_PCI)
483 #define CONFIG_CMD_PCI
484 #define CONFIG_CMD_SCSI
485 #define CONFIG_CMD_EXT2
486 #define CONFIG_CMD_USB
487 #endif
488 
489 
490 #define CONFIG_WATCHDOG			/* watchdog enabled */
491 #define CONFIG_SYS_WATCHDOG_FREQ	5000	/* Feed interval, 5s */
492 
493 /*
494  * Miscellaneous configurable options
495  */
496 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
497 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
498 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
499 #define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
500 
501 #if defined(CONFIG_CMD_KGDB)
502 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
503 #else
504 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
505 #endif
506 
507 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
508 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
509 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
510 #define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
511 
512 /*
513  * For booting Linux, the board info and command line data
514  * have to be in the first 8 MB of memory, since this is
515  * the maximum mapped by the Linux kernel during initialization.
516  */
517 #define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
518 
519 #if defined(CONFIG_CMD_KGDB)
520 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
521 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
522 #endif
523 
524 /*
525  * Environment Configuration
526  */
527 #define CONFIG_IPADDR		192.168.1.100
528 
529 #define CONFIG_HOSTNAME		unknown
530 #define CONFIG_ROOTPATH		"/opt/nfsroot"
531 #define CONFIG_BOOTFILE		"uImage"
532 #define CONFIG_UBOOTPATH	8610hpcd/u-boot.bin
533 
534 #define CONFIG_SERVERIP		192.168.1.1
535 #define CONFIG_GATEWAYIP	192.168.1.1
536 #define CONFIG_NETMASK		255.255.255.0
537 
538 /* default location for tftp and bootm */
539 #define CONFIG_LOADADDR		1000000
540 
541 #define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
542 #undef	CONFIG_BOOTARGS		/* the boot command will set bootargs */
543 
544 #define CONFIG_BAUDRATE	115200
545 
546 #if defined(CONFIG_PCI1)
547 #define PCI_ENV \
548  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
549 	"echo e;md ${a}e00 9\0" \
550  "pci1regs=setenv a e0008; run pcireg\0" \
551  "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
552 	"pci d.w $b.0 56 1\0" \
553  "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
554 	"pci w.w $b.0 56 ffff\0"	\
555  "pci1err=setenv a e0008; run pcierr\0"	\
556  "pci1errc=setenv a e0008; run pcierrc\0"
557 #else
558 #define	PCI_ENV ""
559 #endif
560 
561 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
562 #define PCIE_ENV \
563  "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
564 	"echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
565  "pcie1regs=setenv a e000a; run pciereg\0"	\
566  "pcie2regs=setenv a e0009; run pciereg\0"	\
567  "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
568 	"pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"	\
569 	"pci d $b.0 130 1\0" \
570  "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
571 	"pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
572 	"pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"		\
573  "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"	\
574  "pcie1err=setenv a e000a; run pcieerr\0"	\
575  "pcie2err=setenv a e0009; run pcieerr\0"	\
576  "pcie1errc=setenv a e000a; run pcieerrc\0"	\
577  "pcie2errc=setenv a e0009; run pcieerrc\0"
578 #else
579 #define	PCIE_ENV ""
580 #endif
581 
582 #define DMA_ENV \
583  "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
584 	"mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
585  "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
586 	"mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
587  "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
588 	"mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
589  "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
590 	"mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
591 
592 #ifdef ENV_DEBUG
593 #define	CONFIG_EXTRA_ENV_SETTINGS				\
594 "netdev=eth0\0"							\
595 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
596 "tftpflash=tftpboot $loadaddr $uboot; "				\
597 	"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
598 		" +$filesize; "	\
599 	"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
600 		" +$filesize; "	\
601 	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
602 		" $filesize; "	\
603 	"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
604 		" +$filesize; "	\
605 	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
606 		" $filesize\0"	\
607 "consoledev=ttyS0\0"						\
608 "ramdiskaddr=2000000\0"					\
609 "ramdiskfile=8610hpcd/ramdisk.uboot\0"				\
610 "fdtaddr=c00000\0"						\
611 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"				\
612 "bdev=sda3\0"					\
613 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
614 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
615 "maxcpus=1"	\
616 "eoi=mw e00400b0 0\0"						\
617 "iack=md e00400a0 1\0"						\
618 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
619 	"md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
620 	"md ${a}f00 5\0" \
621 "ddr1regs=setenv a e0002; run ddrreg\0" \
622 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
623 	"md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
624 	"md ${a}e60 1; md ${a}ef0 1d\0" \
625 "guregs=setenv a e00e0; run gureg\0" \
626 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
627 "mcmregs=setenv a e0001; run mcmreg\0" \
628 "diuregs=md e002c000 1d\0" \
629 "dium=mw e002c01c\0" \
630 "diuerr=md e002c014 1\0" \
631 "pmregs=md e00e1000 2b\0" \
632 "lawregs=md e0000c08 4b\0" \
633 "lbcregs=md e0005000 36\0" \
634 "dma0regs=md e0021100 12\0" \
635 "dma1regs=md e0021180 12\0" \
636 "dma2regs=md e0021200 12\0" \
637 "dma3regs=md e0021280 12\0" \
638  PCI_ENV \
639  PCIE_ENV \
640  DMA_ENV
641 #else
642 #define CONFIG_EXTRA_ENV_SETTINGS				\
643 	"netdev=eth0\0"						\
644 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
645 	"consoledev=ttyS0\0"					\
646 	"ramdiskaddr=2000000\0"					\
647 	"ramdiskfile=8610hpcd/ramdisk.uboot\0"			\
648 	"fdtaddr=c00000\0"					\
649 	"fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"			\
650 	"bdev=sda3\0"
651 #endif
652 
653 #define CONFIG_NFSBOOTCOMMAND					\
654  "setenv bootargs root=/dev/nfs rw "				\
655 	"nfsroot=$serverip:$rootpath "				\
656 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
657 	"console=$consoledev,$baudrate $othbootargs;"		\
658  "tftp $loadaddr $bootfile;"					\
659  "tftp $fdtaddr $fdtfile;"					\
660  "bootm $loadaddr - $fdtaddr"
661 
662 #define CONFIG_RAMBOOTCOMMAND \
663  "setenv bootargs root=/dev/ram rw "				\
664 	"console=$consoledev,$baudrate $othbootargs;"		\
665  "tftp $ramdiskaddr $ramdiskfile;"				\
666  "tftp $loadaddr $bootfile;"					\
667  "tftp $fdtaddr $fdtfile;"					\
668  "bootm $loadaddr $ramdiskaddr $fdtaddr"
669 
670 #define CONFIG_BOOTCOMMAND		\
671  "setenv bootargs root=/dev/$bdev rw "	\
672 	"console=$consoledev,$baudrate $othbootargs;"	\
673  "tftp $loadaddr $bootfile;"		\
674  "tftp $fdtaddr $fdtfile;"		\
675  "bootm $loadaddr - $fdtaddr"
676 
677 #endif	/* __CONFIG_H */
678