1 /* 2 * Copyright 2009-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8569mds board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 #define CONFIG_SYS_SRIO 14 #define CONFIG_SRIO1 /* SRIO port 1 */ 15 16 #define CONFIG_PCIE1 1 /* PCIE controller */ 17 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 18 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 19 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 20 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 21 #define CONFIG_QE /* Enable QE */ 22 #define CONFIG_ENV_OVERWRITE 23 24 #ifndef __ASSEMBLY__ 25 extern unsigned long get_clock_freq(void); 26 #endif 27 /* Replace a call to get_clock_freq (after it is implemented)*/ 28 #define CONFIG_SYS_CLK_FREQ 66666666 29 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 30 31 #ifdef CONFIG_ATM 32 #define CONFIG_PQ_MDS_PIB 33 #define CONFIG_PQ_MDS_PIB_ATM 34 #endif 35 36 /* 37 * These can be toggled for performance analysis, otherwise use default. 38 */ 39 #define CONFIG_L2_CACHE /* toggle L2 cache */ 40 #define CONFIG_BTB /* toggle branch predition */ 41 42 #ifndef CONFIG_SYS_MONITOR_BASE 43 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 44 #endif 45 46 /* 47 * Only possible on E500 Version 2 or newer cores. 48 */ 49 #define CONFIG_ENABLE_36BIT_PHYS 1 50 51 #define CONFIG_BOARD_EARLY_INIT_R 1 52 #define CONFIG_HWCONFIG 53 54 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 55 #define CONFIG_SYS_MEMTEST_END 0x00400000 56 57 /* 58 * Config the L2 Cache as L2 SRAM 59 */ 60 #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 61 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR 62 #define CONFIG_SYS_L2_SIZE (512 << 10) 63 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) 64 65 #define CONFIG_SYS_CCSRBAR 0xe0000000 66 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 67 68 #if defined(CONFIG_NAND_SPL) 69 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 70 #endif 71 72 /* DDR Setup */ 73 #undef CONFIG_FSL_DDR_INTERACTIVE 74 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 75 #define CONFIG_DDR_SPD 76 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 77 78 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 79 80 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 81 /* DDR is system memory*/ 82 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 83 84 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 85 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 86 87 /* I2C addresses of SPD EEPROMs */ 88 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 89 90 /* These are used when DDR doesn't use SPD. */ 91 #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ 92 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F 93 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 94 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 95 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 96 #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 97 #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 98 #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 99 #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 100 #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 101 #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 102 #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 103 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 104 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 105 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 106 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 107 #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 108 #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 109 #define CONFIG_SYS_DDR_CDR_1 0x80040000 110 #define CONFIG_SYS_DDR_CDR_2 0x00000000 111 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 112 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 113 #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ 114 #define CONFIG_SYS_DDR_CONTROL2 0x24400000 115 116 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 117 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 118 #define CONFIG_SYS_DDR_SBE 0x00010000 119 120 #undef CONFIG_CLOCKS_IN_MHZ 121 122 /* 123 * Local Bus Definitions 124 */ 125 126 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 127 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 128 129 #define CONFIG_SYS_BCSR_BASE 0xf8000000 130 #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE 131 132 /*Chip select 0 - Flash*/ 133 #define CONFIG_FLASH_BR_PRELIM 0xfe000801 134 #define CONFIG_FLASH_OR_PRELIM 0xfe000ff7 135 136 /*Chip select 1 - BCSR*/ 137 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 138 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 139 140 /*Chip select 4 - PIB*/ 141 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 142 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 143 144 /*Chip select 5 - PIB*/ 145 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 146 #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 147 148 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 149 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 150 #undef CONFIG_SYS_FLASH_CHECKSUM 151 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 152 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 153 154 #undef CONFIG_SYS_RAMBOOT 155 156 #define CONFIG_FLASH_CFI_DRIVER 157 #define CONFIG_SYS_FLASH_CFI 158 #define CONFIG_SYS_FLASH_EMPTY_INFO 159 160 /* Chip select 3 - NAND */ 161 #ifndef CONFIG_NAND_SPL 162 #define CONFIG_SYS_NAND_BASE 0xFC000000 163 #else 164 #define CONFIG_SYS_NAND_BASE 0xFFF00000 165 #endif 166 167 /* NAND boot: 4K NAND loader config */ 168 #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 169 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) 170 #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) 171 #define CONFIG_SYS_NAND_U_BOOT_START \ 172 (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) 173 #define CONFIG_SYS_NAND_U_BOOT_OFFS (0) 174 #define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) 175 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) 176 177 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 178 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } 179 #define CONFIG_SYS_MAX_NAND_DEVICE 1 180 #define CONFIG_NAND_FSL_ELBC 1 181 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 182 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ 183 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 184 | BR_PS_8 /* Port Size = 8 bit */ \ 185 | BR_MS_FCM /* MSEL = FCM */ \ 186 | BR_V) /* valid */ 187 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 188 | OR_FCM_CSCT \ 189 | OR_FCM_CST \ 190 | OR_FCM_CHT \ 191 | OR_FCM_SCY_1 \ 192 | OR_FCM_TRLX \ 193 | OR_FCM_EHTR) 194 195 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 196 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 197 #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 198 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 199 200 #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ 201 #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ 202 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 203 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 204 205 #define CONFIG_SYS_INIT_RAM_LOCK 1 206 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 207 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 208 209 #define CONFIG_SYS_GBL_DATA_OFFSET \ 210 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 211 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 212 213 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 214 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 215 216 /* Serial Port */ 217 #define CONFIG_CONS_INDEX 1 218 #define CONFIG_SYS_NS16550_SERIAL 219 #define CONFIG_SYS_NS16550_REG_SIZE 1 220 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 221 #ifdef CONFIG_NAND_SPL 222 #define CONFIG_NS16550_MIN_FUNCTIONS 223 #endif 224 225 #define CONFIG_SYS_BAUDRATE_TABLE \ 226 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 227 228 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 229 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 230 231 /* 232 * I2C 233 */ 234 #define CONFIG_SYS_I2C 235 #define CONFIG_SYS_I2C_FSL 236 #define CONFIG_SYS_FSL_I2C_SPEED 400000 237 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 238 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 239 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 240 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 241 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 242 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 243 244 /* 245 * I2C2 EEPROM 246 */ 247 #define CONFIG_ID_EEPROM 248 #ifdef CONFIG_ID_EEPROM 249 #define CONFIG_SYS_I2C_EEPROM_NXID 250 #endif 251 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 252 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 253 #define CONFIG_SYS_EEPROM_BUS_NUM 1 254 255 #define PLPPAR1_I2C_BIT_MASK 0x0000000F 256 #define PLPPAR1_I2C2_VAL 0x00000000 257 #define PLPPAR1_ESDHC_VAL 0x0000000A 258 #define PLPDIR1_I2C_BIT_MASK 0x0000000F 259 #define PLPDIR1_I2C2_VAL 0x0000000F 260 #define PLPDIR1_ESDHC_VAL 0x00000006 261 #define PLPPAR1_UART0_BIT_MASK 0x00000fc0 262 #define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80 263 #define PLPDIR1_UART0_BIT_MASK 0x00000fc0 264 #define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80 265 266 /* 267 * General PCI 268 * Memory Addresses are mapped 1-1. I/O is mapped from 0 269 */ 270 #define CONFIG_SYS_PCIE1_NAME "Slot" 271 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 272 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 273 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 274 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 275 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 276 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 277 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 278 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 279 280 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 281 #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 282 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS 283 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 284 285 #ifdef CONFIG_QE 286 /* 287 * QE UEC ethernet configuration 288 */ 289 #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ 290 #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ 291 292 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 293 #define CONFIG_UEC_ETH 294 #define CONFIG_ETHPRIME "UEC0" 295 #define CONFIG_PHY_MODE_NEED_CHANGE 296 297 #define CONFIG_UEC_ETH1 /* GETH1 */ 298 #define CONFIG_HAS_ETH0 299 300 #ifdef CONFIG_UEC_ETH1 301 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 302 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 303 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 304 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 305 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 306 #define CONFIG_SYS_UEC1_PHY_ADDR 7 307 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 308 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 309 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 310 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ 311 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 312 #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ 313 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 314 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 315 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 316 #endif /* CONFIG_UEC_ETH1 */ 317 318 #define CONFIG_UEC_ETH2 /* GETH2 */ 319 #define CONFIG_HAS_ETH1 320 321 #ifdef CONFIG_UEC_ETH2 322 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 323 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 324 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 325 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 326 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 327 #define CONFIG_SYS_UEC2_PHY_ADDR 1 328 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 329 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 330 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 331 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ 332 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 333 #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ 334 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 335 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 336 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 337 #endif /* CONFIG_UEC_ETH2 */ 338 339 #define CONFIG_UEC_ETH3 /* GETH3 */ 340 #define CONFIG_HAS_ETH2 341 342 #ifdef CONFIG_UEC_ETH3 343 #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ 344 #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE 345 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 346 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 347 #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH 348 #define CONFIG_SYS_UEC3_PHY_ADDR 2 349 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 350 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000 351 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 352 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ 353 #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH 354 #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ 355 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 356 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100 357 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 358 #endif /* CONFIG_UEC_ETH3 */ 359 360 #define CONFIG_UEC_ETH4 /* GETH4 */ 361 #define CONFIG_HAS_ETH3 362 363 #ifdef CONFIG_UEC_ETH4 364 #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ 365 #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE 366 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 367 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 368 #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH 369 #define CONFIG_SYS_UEC4_PHY_ADDR 3 370 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 371 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000 372 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 373 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ 374 #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH 375 #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ 376 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 377 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100 378 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 379 #endif /* CONFIG_UEC_ETH4 */ 380 381 #undef CONFIG_UEC_ETH6 /* GETH6 */ 382 #define CONFIG_HAS_ETH5 383 384 #ifdef CONFIG_UEC_ETH6 385 #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ 386 #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE 387 #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE 388 #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH 389 #define CONFIG_SYS_UEC6_PHY_ADDR 4 390 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 391 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000 392 #endif /* CONFIG_UEC_ETH6 */ 393 394 #undef CONFIG_UEC_ETH8 /* GETH8 */ 395 #define CONFIG_HAS_ETH7 396 397 #ifdef CONFIG_UEC_ETH8 398 #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ 399 #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE 400 #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE 401 #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH 402 #define CONFIG_SYS_UEC8_PHY_ADDR 6 403 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 404 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000 405 #endif /* CONFIG_UEC_ETH8 */ 406 407 #endif /* CONFIG_QE */ 408 409 #if defined(CONFIG_PCI) 410 #undef CONFIG_EEPRO100 411 #undef CONFIG_TULIP 412 413 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 414 415 #endif /* CONFIG_PCI */ 416 417 /* 418 * Environment 419 */ 420 #if defined(CONFIG_SYS_RAMBOOT) 421 #else 422 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 423 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 424 #define CONFIG_ENV_SIZE 0x2000 425 #endif 426 427 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 428 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 429 430 /* QE microcode/firmware address */ 431 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 432 #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 433 434 /* 435 * BOOTP options 436 */ 437 #define CONFIG_BOOTP_BOOTFILESIZE 438 439 #undef CONFIG_WATCHDOG /* watchdog disabled */ 440 441 #ifdef CONFIG_MMC 442 #define CONFIG_FSL_ESDHC 443 #define CONFIG_FSL_ESDHC_PIN_MUX 444 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 445 #endif 446 447 /* 448 * Miscellaneous configurable options 449 */ 450 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 451 #if defined(CONFIG_CMD_KGDB) 452 #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ 453 #else 454 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 455 #endif 456 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 457 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 458 /* Boot Argument Buffer Size */ 459 460 /* 461 * For booting Linux, the board info and command line data 462 * have to be in the first 64 MB of memory, since this is 463 * the maximum mapped by the Linux kernel during initialization. 464 */ 465 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 466 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 467 468 #if defined(CONFIG_CMD_KGDB) 469 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 470 #endif 471 472 /* 473 * Environment Configuration 474 */ 475 #define CONFIG_HOSTNAME mpc8569mds 476 #define CONFIG_ROOTPATH "/nfsroot" 477 #define CONFIG_BOOTFILE "your.uImage" 478 479 #define CONFIG_SERVERIP 192.168.1.1 480 #define CONFIG_GATEWAYIP 192.168.1.1 481 #define CONFIG_NETMASK 255.255.255.0 482 483 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 484 485 #define CONFIG_EXTRA_ENV_SETTINGS \ 486 "netdev=eth0\0" \ 487 "consoledev=ttyS0\0" \ 488 "ramdiskaddr=600000\0" \ 489 "ramdiskfile=your.ramdisk.u-boot\0" \ 490 "fdtaddr=400000\0" \ 491 "fdtfile=your.fdt.dtb\0" \ 492 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 493 "nfsroot=$serverip:$rootpath " \ 494 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 495 "console=$consoledev,$baudrate $othbootargs\0" \ 496 "ramargs=setenv bootargs root=/dev/ram rw " \ 497 "console=$consoledev,$baudrate $othbootargs\0" \ 498 499 #define CONFIG_NFSBOOTCOMMAND \ 500 "run nfsargs;" \ 501 "tftp $loadaddr $bootfile;" \ 502 "tftp $fdtaddr $fdtfile;" \ 503 "bootm $loadaddr - $fdtaddr" 504 505 #define CONFIG_RAMBOOTCOMMAND \ 506 "run ramargs;" \ 507 "tftp $ramdiskaddr $ramdiskfile;" \ 508 "tftp $loadaddr $bootfile;" \ 509 "bootm $loadaddr $ramdiskaddr" 510 511 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 512 513 #endif /* __CONFIG_H */ 514