1 /* 2 * Copyright (C) 2009 Freescale Semiconductor, Inc. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8569mds board configuration file 25 */ 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* High Level Configuration Options */ 30 #define CONFIG_BOOKE 1 /* BOOKE */ 31 #define CONFIG_E500 1 /* BOOKE e500 family */ 32 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ 33 #define CONFIG_MPC8569 1 /* MPC8569 specific */ 34 #define CONFIG_MPC8569MDS 1 /* MPC8569MDS board specific */ 35 36 #define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ 37 38 #define CONFIG_PCI 1 /* Disable PCI/PCIE */ 39 #define CONFIG_PCIE1 1 /* PCIE controller */ 40 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 41 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 42 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 43 #define CONFIG_QE /* Enable QE */ 44 #define CONFIG_ENV_OVERWRITE 45 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 46 47 /* 48 * When initializing flash, if we cannot find the manufacturer ID, 49 * assume this is the AMD flash associated with the MDS board. 50 * This allows booting from a promjet. 51 */ 52 #define CONFIG_ASSUME_AMD_FLASH 53 54 #ifndef __ASSEMBLY__ 55 extern unsigned long get_clock_freq(void); 56 #endif 57 /* Replace a call to get_clock_freq (after it is implemented)*/ 58 #define CONFIG_SYS_CLK_FREQ 66666666 59 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 60 61 /* 62 * These can be toggled for performance analysis, otherwise use default. 63 */ 64 #define CONFIG_L2_CACHE /* toggle L2 cache */ 65 #define CONFIG_BTB /* toggle branch predition */ 66 67 /* 68 * Only possible on E500 Version 2 or newer cores. 69 */ 70 #define CONFIG_ENABLE_36BIT_PHYS 1 71 72 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 73 74 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 75 #define CONFIG_SYS_MEMTEST_END 0x00400000 76 77 /* 78 * Base addresses -- Note these are effective addresses where the 79 * actual resources get mapped (not physical addresses) 80 */ 81 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 82 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 83 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR 84 /* physical addr of CCSRBAR */ 85 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR 86 /* PQII uses CONFIG_SYS_IMMR */ 87 88 #define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) 89 #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) 90 91 /* DDR Setup */ 92 #define CONFIG_FSL_DDR3 93 #undef CONFIG_FSL_DDR_INTERACTIVE 94 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 95 #define CONFIG_DDR_SPD 96 #define CONFIG_DDR_DLL /* possible DLL fix needed */ 97 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 98 99 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 100 101 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 102 /* DDR is system memory*/ 103 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 104 105 #define CONFIG_NUM_DDR_CONTROLLERS 1 106 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 107 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 108 109 /* I2C addresses of SPD EEPROMs */ 110 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 111 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */ 112 113 /* These are used when DDR doesn't use SPD. */ 114 #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ 115 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F 116 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 117 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 118 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 119 #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 120 #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 121 #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 122 #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 123 #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 124 #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 125 #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 126 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 127 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 128 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 129 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 130 #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 131 #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 132 #define CONFIG_SYS_DDR_CDR_1 0x80040000 133 #define CONFIG_SYS_DDR_CDR_2 0x00000000 134 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 135 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 136 #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ 137 #define CONFIG_SYS_DDR_CONTROL2 0x24400000 138 139 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 140 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 141 #define CONFIG_SYS_DDR_SBE 0x00010000 142 143 #undef CONFIG_CLOCKS_IN_MHZ 144 145 /* 146 * Local Bus Definitions 147 */ 148 149 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 150 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 151 152 #define CONFIG_SYS_BCSR_BASE 0xf8000000 153 #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE 154 155 /*Chip select 0 - Flash*/ 156 #define CONFIG_SYS_BR0_PRELIM 0xfe000801 157 #define CONFIG_SYS_OR0_PRELIM 0xfe000ff7 158 159 /*Chip select 1 - BCSR*/ 160 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 161 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 162 163 /*Chip select 4 - PIB*/ 164 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 165 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 166 167 /*Chip select 5 - PIB*/ 168 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 169 #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 170 171 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 172 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 173 #undef CONFIG_SYS_FLASH_CHECKSUM 174 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 175 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 176 177 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ 178 179 #define CONFIG_FLASH_CFI_DRIVER 180 #define CONFIG_SYS_FLASH_CFI 181 #define CONFIG_SYS_FLASH_EMPTY_INFO 182 183 184 /* 185 * SDRAM on the LocalBus 186 */ 187 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 188 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 189 190 #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ 191 #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ 192 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 193 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 194 195 #define CONFIG_SYS_INIT_RAM_LOCK 1 196 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 197 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ 198 199 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 200 #define CONFIG_SYS_GBL_DATA_OFFSET \ 201 (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 202 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 203 204 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 205 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 206 207 /* Serial Port */ 208 #define CONFIG_CONS_INDEX 1 209 #undef CONFIG_SERIAL_SOFTWARE_FIFO 210 #define CONFIG_SYS_NS16550 211 #define CONFIG_SYS_NS16550_SERIAL 212 #define CONFIG_SYS_NS16550_REG_SIZE 1 213 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 214 215 #define CONFIG_SYS_BAUDRATE_TABLE \ 216 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 217 218 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 219 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 220 221 /* Use the HUSH parser*/ 222 #define CONFIG_SYS_HUSH_PARSER 223 #ifdef CONFIG_SYS_HUSH_PARSER 224 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 225 #endif 226 227 /* pass open firmware flat tree */ 228 #define CONFIG_OF_LIBFDT 1 229 #define CONFIG_OF_BOARD_SETUP 1 230 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 231 232 #define CONFIG_SYS_64BIT_VSPRINTF 1 233 #define CONFIG_SYS_64BIT_STRTOUL 1 234 235 /* 236 * I2C 237 */ 238 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 239 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 240 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 241 #define CONFIG_I2C_MULTI_BUS 242 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 243 #define CONFIG_SYS_I2C_SLAVE 0x7F 244 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ 245 #define CONFIG_SYS_I2C_OFFSET 0x3000 246 #define CONFIG_SYS_I2C2_OFFSET 0x3100 247 248 /* 249 * I2C2 EEPROM 250 */ 251 #define CONFIG_ID_EEPROM 252 #ifdef CONFIG_ID_EEPROM 253 #define CONFIG_SYS_I2C_EEPROM_NXID 254 #endif 255 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 256 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 257 #define CONFIG_SYS_EEPROM_BUS_NUM 1 258 259 #define PLPPAR1_I2C_BIT_MASK 0x0000000F 260 #define PLPPAR1_I2C2_VAL 0x00000000 261 #define PLPDIR1_I2C_BIT_MASK 0x0000000F 262 #define PLPDIR1_I2C2_VAL 0x0000000F 263 264 /* 265 * General PCI 266 * Memory Addresses are mapped 1-1. I/O is mapped from 0 267 */ 268 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 269 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 270 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 271 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 272 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 273 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 274 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 275 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 276 277 #define CONFIG_SYS_SRIO_MEM_VIRT 0xc0000000 278 #define CONFIG_SYS_SRIO_MEM_BUS 0xc0000000 279 #define CONFIG_SYS_SRIO_MEM_PHYS 0xc0000000 280 281 #ifdef CONFIG_QE 282 /* 283 * QE UEC ethernet configuration 284 */ 285 #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ 286 #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ 287 288 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 289 #define CONFIG_UEC_ETH 290 #define CONFIG_ETHPRIME "FSL UEC0" 291 #define CONFIG_PHY_MODE_NEED_CHANGE 292 293 #define CONFIG_UEC_ETH1 /* GETH1 */ 294 #define CONFIG_HAS_ETH0 295 296 #ifdef CONFIG_UEC_ETH1 297 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 298 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 299 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 300 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 301 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 302 #define CONFIG_SYS_UEC1_PHY_ADDR 7 303 #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID 304 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 305 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ 306 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 307 #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ 308 #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII 309 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 310 #endif /* CONFIG_UEC_ETH1 */ 311 312 #define CONFIG_UEC_ETH2 /* GETH2 */ 313 #define CONFIG_HAS_ETH1 314 315 #ifdef CONFIG_UEC_ETH2 316 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 317 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 318 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 319 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 320 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 321 #define CONFIG_SYS_UEC2_PHY_ADDR 1 322 #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID 323 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 324 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ 325 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 326 #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ 327 #define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_100_RMII 328 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 329 #endif /* CONFIG_UEC_ETH2 */ 330 331 #define CONFIG_UEC_ETH3 /* GETH3 */ 332 #define CONFIG_HAS_ETH2 333 334 #ifdef CONFIG_UEC_ETH3 335 #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ 336 #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE 337 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 338 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 339 #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH 340 #define CONFIG_SYS_UEC3_PHY_ADDR 2 341 #define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_1000_RGMII_ID 342 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 343 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ 344 #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH 345 #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ 346 #define CONFIG_SYS_UEC3_INTERFACE_MODE ENET_100_RMII 347 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 348 #endif /* CONFIG_UEC_ETH3 */ 349 350 #define CONFIG_UEC_ETH4 /* GETH4 */ 351 #define CONFIG_HAS_ETH3 352 353 #ifdef CONFIG_UEC_ETH4 354 #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ 355 #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE 356 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 357 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 358 #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH 359 #define CONFIG_SYS_UEC4_PHY_ADDR 3 360 #define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_1000_RGMII_ID 361 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 362 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ 363 #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH 364 #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ 365 #define CONFIG_SYS_UEC4_INTERFACE_MODE ENET_100_RMII 366 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 367 #endif /* CONFIG_UEC_ETH4 */ 368 369 #undef CONFIG_UEC_ETH6 /* GETH6 */ 370 #define CONFIG_HAS_ETH5 371 372 #ifdef CONFIG_UEC_ETH6 373 #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ 374 #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE 375 #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE 376 #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH 377 #define CONFIG_SYS_UEC6_PHY_ADDR 4 378 #define CONFIG_SYS_UEC6_INTERFACE_MODE ENET_1000_SGMII 379 #endif /* CONFIG_UEC_ETH6 */ 380 381 #undef CONFIG_UEC_ETH8 /* GETH8 */ 382 #define CONFIG_HAS_ETH7 383 384 #ifdef CONFIG_UEC_ETH8 385 #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ 386 #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE 387 #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE 388 #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH 389 #define CONFIG_SYS_UEC8_PHY_ADDR 6 390 #define CONFIG_SYS_UEC8_INTERFACE_MODE ENET_1000_SGMII 391 #endif /* CONFIG_UEC_ETH8 */ 392 393 #endif /* CONFIG_QE */ 394 395 #if defined(CONFIG_PCI) 396 397 #define CONFIG_NET_MULTI 398 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 399 400 #undef CONFIG_EEPRO100 401 #undef CONFIG_TULIP 402 403 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 404 405 #endif /* CONFIG_PCI */ 406 407 #ifndef CONFIG_NET_MULTI 408 #define CONFIG_NET_MULTI 1 409 #endif 410 411 /* 412 * Environment 413 */ 414 #define CONFIG_ENV_IS_IN_FLASH 1 415 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 416 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */ 417 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 418 419 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 420 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 421 422 /* QE microcode/firmware address */ 423 #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 424 425 /* 426 * BOOTP options 427 */ 428 #define CONFIG_BOOTP_BOOTFILESIZE 429 #define CONFIG_BOOTP_BOOTPATH 430 #define CONFIG_BOOTP_GATEWAY 431 #define CONFIG_BOOTP_HOSTNAME 432 433 434 /* 435 * Command line configuration. 436 */ 437 #include <config_cmd_default.h> 438 439 #define CONFIG_CMD_PING 440 #define CONFIG_CMD_I2C 441 #define CONFIG_CMD_MII 442 #define CONFIG_CMD_ELF 443 #define CONFIG_CMD_IRQ 444 #define CONFIG_CMD_SETEXPR 445 446 #if defined(CONFIG_PCI) 447 #define CONFIG_CMD_PCI 448 #endif 449 450 451 #undef CONFIG_WATCHDOG /* watchdog disabled */ 452 453 /* 454 * Miscellaneous configurable options 455 */ 456 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 457 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 458 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 459 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 460 #if defined(CONFIG_CMD_KGDB) 461 #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ 462 #else 463 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 464 #endif 465 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 466 /* Print Buffer Size */ 467 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 468 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 469 /* Boot Argument Buffer Size */ 470 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 471 472 /* 473 * For booting Linux, the board info and command line data 474 * have to be in the first 16 MB of memory, since this is 475 * the maximum mapped by the Linux kernel during initialization. 476 */ 477 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) 478 /* Initial Memory map for Linux*/ 479 480 /* 481 * Internal Definitions 482 * 483 * Boot Flags 484 */ 485 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 486 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 487 488 #if defined(CONFIG_CMD_KGDB) 489 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 490 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 491 #endif 492 493 /* 494 * Environment Configuration 495 */ 496 #define CONFIG_HOSTNAME mpc8569mds 497 #define CONFIG_ROOTPATH /nfsroot 498 #define CONFIG_BOOTFILE your.uImage 499 500 #define CONFIG_SERVERIP 192.168.1.1 501 #define CONFIG_GATEWAYIP 192.168.1.1 502 #define CONFIG_NETMASK 255.255.255.0 503 504 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 505 506 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 507 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 508 509 #define CONFIG_BAUDRATE 115200 510 511 #define CONFIG_EXTRA_ENV_SETTINGS \ 512 "netdev=eth0\0" \ 513 "consoledev=ttyS0\0" \ 514 "ramdiskaddr=600000\0" \ 515 "ramdiskfile=your.ramdisk.u-boot\0" \ 516 "fdtaddr=400000\0" \ 517 "fdtfile=your.fdt.dtb\0" \ 518 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 519 "nfsroot=$serverip:$rootpath " \ 520 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 521 "console=$consoledev,$baudrate $othbootargs\0" \ 522 "ramargs=setenv bootargs root=/dev/ram rw " \ 523 "console=$consoledev,$baudrate $othbootargs\0" \ 524 525 #define CONFIG_NFSBOOTCOMMAND \ 526 "run nfsargs;" \ 527 "tftp $loadaddr $bootfile;" \ 528 "tftp $fdtaddr $fdtfile;" \ 529 "bootm $loadaddr - $fdtaddr" 530 531 #define CONFIG_RAMBOOTCOMMAND \ 532 "run ramargs;" \ 533 "tftp $ramdiskaddr $ramdiskfile;" \ 534 "tftp $loadaddr $bootfile;" \ 535 "bootm $loadaddr $ramdiskaddr" 536 537 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 538 539 #endif /* __CONFIG_H */ 540