1 /* 2 * Copyright 2009-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8569mds board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* High Level Configuration Options */ 14 #define CONFIG_BOOKE 1 /* BOOKE */ 15 #define CONFIG_E500 1 /* BOOKE e500 family */ 16 #define CONFIG_MPC8569 1 /* MPC8569 specific */ 17 #define CONFIG_MPC8569MDS 1 /* MPC8569MDS board specific */ 18 19 #define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ 20 21 #define CONFIG_SYS_SRIO 22 #define CONFIG_SRIO1 /* SRIO port 1 */ 23 24 #define CONFIG_PCI 1 /* Disable PCI/PCIE */ 25 #define CONFIG_PCIE1 1 /* PCIE controller */ 26 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 27 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 28 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 29 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 30 #define CONFIG_QE /* Enable QE */ 31 #define CONFIG_ENV_OVERWRITE 32 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 33 34 #ifndef __ASSEMBLY__ 35 extern unsigned long get_clock_freq(void); 36 #endif 37 /* Replace a call to get_clock_freq (after it is implemented)*/ 38 #define CONFIG_SYS_CLK_FREQ 66666666 39 #define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ 40 41 #ifdef CONFIG_ATM 42 #define CONFIG_PQ_MDS_PIB 43 #define CONFIG_PQ_MDS_PIB_ATM 44 #endif 45 46 /* 47 * These can be toggled for performance analysis, otherwise use default. 48 */ 49 #define CONFIG_L2_CACHE /* toggle L2 cache */ 50 #define CONFIG_BTB /* toggle branch predition */ 51 52 #ifndef CONFIG_SYS_TEXT_BASE 53 #define CONFIG_SYS_TEXT_BASE 0xfff80000 54 #endif 55 56 #ifndef CONFIG_SYS_MONITOR_BASE 57 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 58 #endif 59 60 /* 61 * Only possible on E500 Version 2 or newer cores. 62 */ 63 #define CONFIG_ENABLE_36BIT_PHYS 1 64 65 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 66 #define CONFIG_BOARD_EARLY_INIT_R 1 67 #define CONFIG_HWCONFIG 68 69 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 70 #define CONFIG_SYS_MEMTEST_END 0x00400000 71 72 /* 73 * Config the L2 Cache as L2 SRAM 74 */ 75 #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 76 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR 77 #define CONFIG_SYS_L2_SIZE (512 << 10) 78 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) 79 80 #define CONFIG_SYS_CCSRBAR 0xe0000000 81 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 82 83 #if defined(CONFIG_NAND_SPL) 84 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 85 #endif 86 87 /* DDR Setup */ 88 #define CONFIG_SYS_FSL_DDR3 89 #undef CONFIG_FSL_DDR_INTERACTIVE 90 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 91 #define CONFIG_DDR_SPD 92 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 93 94 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 95 96 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 97 /* DDR is system memory*/ 98 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 99 100 #define CONFIG_NUM_DDR_CONTROLLERS 1 101 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 102 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 103 104 /* I2C addresses of SPD EEPROMs */ 105 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 106 107 /* These are used when DDR doesn't use SPD. */ 108 #define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ 109 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F 110 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 111 #define CONFIG_SYS_DDR_TIMING_3 0x00020000 112 #define CONFIG_SYS_DDR_TIMING_0 0x00330004 113 #define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 114 #define CONFIG_SYS_DDR_TIMING_2 0x002888D0 115 #define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 116 #define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 117 #define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 118 #define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 119 #define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 120 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 121 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 122 #define CONFIG_SYS_DDR_TIMING_4 0x00220001 123 #define CONFIG_SYS_DDR_TIMING_5 0x03402400 124 #define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 125 #define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 126 #define CONFIG_SYS_DDR_CDR_1 0x80040000 127 #define CONFIG_SYS_DDR_CDR_2 0x00000000 128 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 129 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 130 #define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ 131 #define CONFIG_SYS_DDR_CONTROL2 0x24400000 132 133 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 134 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 135 #define CONFIG_SYS_DDR_SBE 0x00010000 136 137 #undef CONFIG_CLOCKS_IN_MHZ 138 139 /* 140 * Local Bus Definitions 141 */ 142 143 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 144 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 145 146 #define CONFIG_SYS_BCSR_BASE 0xf8000000 147 #define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE 148 149 /*Chip select 0 - Flash*/ 150 #define CONFIG_FLASH_BR_PRELIM 0xfe000801 151 #define CONFIG_FLASH_OR_PRELIM 0xfe000ff7 152 153 /*Chip select 1 - BCSR*/ 154 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 155 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 156 157 /*Chip select 4 - PIB*/ 158 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 159 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 160 161 /*Chip select 5 - PIB*/ 162 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 163 #define CONFIG_SYS_OR5_PRELIM 0xffffe9f7 164 165 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 166 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 167 #undef CONFIG_SYS_FLASH_CHECKSUM 168 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 169 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 170 171 #undef CONFIG_SYS_RAMBOOT 172 173 #define CONFIG_FLASH_CFI_DRIVER 174 #define CONFIG_SYS_FLASH_CFI 175 #define CONFIG_SYS_FLASH_EMPTY_INFO 176 177 /* Chip select 3 - NAND */ 178 #ifndef CONFIG_NAND_SPL 179 #define CONFIG_SYS_NAND_BASE 0xFC000000 180 #else 181 #define CONFIG_SYS_NAND_BASE 0xFFF00000 182 #endif 183 184 /* NAND boot: 4K NAND loader config */ 185 #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 186 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) 187 #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) 188 #define CONFIG_SYS_NAND_U_BOOT_START \ 189 (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) 190 #define CONFIG_SYS_NAND_U_BOOT_OFFS (0) 191 #define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) 192 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) 193 194 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 195 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE, } 196 #define CONFIG_SYS_MAX_NAND_DEVICE 1 197 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 198 #define CONFIG_CMD_NAND 1 199 #define CONFIG_NAND_FSL_ELBC 1 200 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 201 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \ 202 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 203 | BR_PS_8 /* Port Size = 8 bit */ \ 204 | BR_MS_FCM /* MSEL = FCM */ \ 205 | BR_V) /* valid */ 206 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 207 | OR_FCM_CSCT \ 208 | OR_FCM_CST \ 209 | OR_FCM_CHT \ 210 | OR_FCM_SCY_1 \ 211 | OR_FCM_TRLX \ 212 | OR_FCM_EHTR) 213 214 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 215 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 216 #define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 217 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 218 219 #define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ 220 #define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ 221 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 222 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 223 224 #define CONFIG_SYS_INIT_RAM_LOCK 1 225 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 226 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 227 228 #define CONFIG_SYS_GBL_DATA_OFFSET \ 229 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 230 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 231 232 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 233 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 234 235 /* Serial Port */ 236 #define CONFIG_CONS_INDEX 1 237 #define CONFIG_SYS_NS16550 238 #define CONFIG_SYS_NS16550_SERIAL 239 #define CONFIG_SYS_NS16550_REG_SIZE 1 240 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 241 #ifdef CONFIG_NAND_SPL 242 #define CONFIG_NS16550_MIN_FUNCTIONS 243 #endif 244 245 #define CONFIG_SYS_BAUDRATE_TABLE \ 246 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 247 248 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 249 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 250 251 /* Use the HUSH parser*/ 252 #define CONFIG_SYS_HUSH_PARSER 253 #ifdef CONFIG_SYS_HUSH_PARSER 254 #endif 255 256 /* pass open firmware flat tree */ 257 #define CONFIG_OF_LIBFDT 1 258 #define CONFIG_OF_BOARD_SETUP 1 259 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 260 261 /* 262 * I2C 263 */ 264 #define CONFIG_SYS_I2C 265 #define CONFIG_SYS_I2C_FSL 266 #define CONFIG_SYS_FSL_I2C_SPEED 400000 267 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 268 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 269 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 270 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 271 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 272 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 273 274 /* 275 * I2C2 EEPROM 276 */ 277 #define CONFIG_ID_EEPROM 278 #ifdef CONFIG_ID_EEPROM 279 #define CONFIG_SYS_I2C_EEPROM_NXID 280 #endif 281 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 282 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 283 #define CONFIG_SYS_EEPROM_BUS_NUM 1 284 285 #define PLPPAR1_I2C_BIT_MASK 0x0000000F 286 #define PLPPAR1_I2C2_VAL 0x00000000 287 #define PLPPAR1_ESDHC_VAL 0x0000000A 288 #define PLPDIR1_I2C_BIT_MASK 0x0000000F 289 #define PLPDIR1_I2C2_VAL 0x0000000F 290 #define PLPDIR1_ESDHC_VAL 0x00000006 291 #define PLPPAR1_UART0_BIT_MASK 0x00000fc0 292 #define PLPPAR1_ESDHC_4BITS_VAL 0x00000a80 293 #define PLPDIR1_UART0_BIT_MASK 0x00000fc0 294 #define PLPDIR1_ESDHC_4BITS_VAL 0x00000a80 295 296 /* 297 * General PCI 298 * Memory Addresses are mapped 1-1. I/O is mapped from 0 299 */ 300 #define CONFIG_SYS_PCIE1_NAME "Slot" 301 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 302 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 303 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 304 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 305 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 306 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 307 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 308 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 309 310 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 311 #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 312 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS 313 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 314 315 #ifdef CONFIG_QE 316 /* 317 * QE UEC ethernet configuration 318 */ 319 #define CONFIG_SYS_UCC_RGMII_MODE /* Set UCC work at RGMII by default */ 320 #undef CONFIG_SYS_UCC_RMII_MODE /* Set UCC work at RMII mode */ 321 322 #define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) 323 #define CONFIG_UEC_ETH 324 #define CONFIG_ETHPRIME "UEC0" 325 #define CONFIG_PHY_MODE_NEED_CHANGE 326 327 #define CONFIG_UEC_ETH1 /* GETH1 */ 328 #define CONFIG_HAS_ETH0 329 330 #ifdef CONFIG_UEC_ETH1 331 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 332 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 333 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 334 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 335 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 336 #define CONFIG_SYS_UEC1_PHY_ADDR 7 337 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 338 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 339 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 340 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 /* CLK16 for RMII */ 341 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 342 #define CONFIG_SYS_UEC1_PHY_ADDR 8 /* 0x8 for RMII */ 343 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 344 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 345 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 346 #endif /* CONFIG_UEC_ETH1 */ 347 348 #define CONFIG_UEC_ETH2 /* GETH2 */ 349 #define CONFIG_HAS_ETH1 350 351 #ifdef CONFIG_UEC_ETH2 352 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 353 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 354 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 355 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 356 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 357 #define CONFIG_SYS_UEC2_PHY_ADDR 1 358 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 359 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 360 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 361 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 /* CLK 16 for RMII */ 362 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 363 #define CONFIG_SYS_UEC2_PHY_ADDR 0x9 /* 0x9 for RMII */ 364 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 365 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 366 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 367 #endif /* CONFIG_UEC_ETH2 */ 368 369 #define CONFIG_UEC_ETH3 /* GETH3 */ 370 #define CONFIG_HAS_ETH2 371 372 #ifdef CONFIG_UEC_ETH3 373 #define CONFIG_SYS_UEC3_UCC_NUM 2 /* UCC3 */ 374 #define CONFIG_SYS_UEC3_RX_CLK QE_CLK_NONE 375 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 376 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK12 377 #define CONFIG_SYS_UEC3_ETH_TYPE GIGA_ETH 378 #define CONFIG_SYS_UEC3_PHY_ADDR 2 379 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 380 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000 381 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 382 #define CONFIG_SYS_UEC3_TX_CLK QE_CLK16 /* CLK_16 for RMII */ 383 #define CONFIG_SYS_UEC3_ETH_TYPE FAST_ETH 384 #define CONFIG_SYS_UEC3_PHY_ADDR 0xA /* 0xA for RMII */ 385 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 386 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100 387 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 388 #endif /* CONFIG_UEC_ETH3 */ 389 390 #define CONFIG_UEC_ETH4 /* GETH4 */ 391 #define CONFIG_HAS_ETH3 392 393 #ifdef CONFIG_UEC_ETH4 394 #define CONFIG_SYS_UEC4_UCC_NUM 3 /* UCC4 */ 395 #define CONFIG_SYS_UEC4_RX_CLK QE_CLK_NONE 396 #if defined(CONFIG_SYS_UCC_RGMII_MODE) 397 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK17 398 #define CONFIG_SYS_UEC4_ETH_TYPE GIGA_ETH 399 #define CONFIG_SYS_UEC4_PHY_ADDR 3 400 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 401 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000 402 #elif defined(CONFIG_SYS_UCC_RMII_MODE) 403 #define CONFIG_SYS_UEC4_TX_CLK QE_CLK16 /* CLK16 for RMII */ 404 #define CONFIG_SYS_UEC4_ETH_TYPE FAST_ETH 405 #define CONFIG_SYS_UEC4_PHY_ADDR 0xB /* 0xB for RMII */ 406 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII 407 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100 408 #endif /* CONFIG_SYS_UCC_RGMII_MODE */ 409 #endif /* CONFIG_UEC_ETH4 */ 410 411 #undef CONFIG_UEC_ETH6 /* GETH6 */ 412 #define CONFIG_HAS_ETH5 413 414 #ifdef CONFIG_UEC_ETH6 415 #define CONFIG_SYS_UEC6_UCC_NUM 5 /* UCC6 */ 416 #define CONFIG_SYS_UEC6_RX_CLK QE_CLK_NONE 417 #define CONFIG_SYS_UEC6_TX_CLK QE_CLK_NONE 418 #define CONFIG_SYS_UEC6_ETH_TYPE GIGA_ETH 419 #define CONFIG_SYS_UEC6_PHY_ADDR 4 420 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 421 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000 422 #endif /* CONFIG_UEC_ETH6 */ 423 424 #undef CONFIG_UEC_ETH8 /* GETH8 */ 425 #define CONFIG_HAS_ETH7 426 427 #ifdef CONFIG_UEC_ETH8 428 #define CONFIG_SYS_UEC8_UCC_NUM 7 /* UCC8 */ 429 #define CONFIG_SYS_UEC8_RX_CLK QE_CLK_NONE 430 #define CONFIG_SYS_UEC8_TX_CLK QE_CLK_NONE 431 #define CONFIG_SYS_UEC8_ETH_TYPE GIGA_ETH 432 #define CONFIG_SYS_UEC8_PHY_ADDR 6 433 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII 434 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000 435 #endif /* CONFIG_UEC_ETH8 */ 436 437 #endif /* CONFIG_QE */ 438 439 #if defined(CONFIG_PCI) 440 441 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 442 443 #undef CONFIG_EEPRO100 444 #undef CONFIG_TULIP 445 #define CONFIG_E1000 /* Define e1000 pci Ethernet card */ 446 447 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 448 449 #endif /* CONFIG_PCI */ 450 451 /* 452 * Environment 453 */ 454 #if defined(CONFIG_SYS_RAMBOOT) 455 #else 456 #define CONFIG_ENV_IS_IN_FLASH 1 457 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 458 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 459 #define CONFIG_ENV_SIZE 0x2000 460 #endif 461 462 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 463 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 464 465 /* QE microcode/firmware address */ 466 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 467 #define CONFIG_SYS_QE_FW_ADDR 0xfff00000 468 469 /* 470 * BOOTP options 471 */ 472 #define CONFIG_BOOTP_BOOTFILESIZE 473 #define CONFIG_BOOTP_BOOTPATH 474 #define CONFIG_BOOTP_GATEWAY 475 #define CONFIG_BOOTP_HOSTNAME 476 477 478 /* 479 * Command line configuration. 480 */ 481 #include <config_cmd_default.h> 482 483 #define CONFIG_CMD_PING 484 #define CONFIG_CMD_I2C 485 #define CONFIG_CMD_MII 486 #define CONFIG_CMD_ELF 487 #define CONFIG_CMD_IRQ 488 #define CONFIG_CMD_SETEXPR 489 #define CONFIG_CMD_REGINFO 490 491 #if defined(CONFIG_PCI) 492 #define CONFIG_CMD_PCI 493 #endif 494 495 496 #undef CONFIG_WATCHDOG /* watchdog disabled */ 497 498 #define CONFIG_MMC 1 499 500 #ifdef CONFIG_MMC 501 #define CONFIG_FSL_ESDHC 502 #define CONFIG_FSL_ESDHC_PIN_MUX 503 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 504 #define CONFIG_CMD_MMC 505 #define CONFIG_GENERIC_MMC 506 #define CONFIG_CMD_EXT2 507 #define CONFIG_CMD_FAT 508 #define CONFIG_DOS_PARTITION 509 #endif 510 511 /* 512 * Miscellaneous configurable options 513 */ 514 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 515 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 516 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 517 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 518 #if defined(CONFIG_CMD_KGDB) 519 #define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ 520 #else 521 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 522 #endif 523 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 524 /* Print Buffer Size */ 525 #define CONFIG_SYS_MAXARGS 32 /* max number of command args */ 526 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 527 /* Boot Argument Buffer Size */ 528 529 /* 530 * For booting Linux, the board info and command line data 531 * have to be in the first 64 MB of memory, since this is 532 * the maximum mapped by the Linux kernel during initialization. 533 */ 534 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 535 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 536 537 #if defined(CONFIG_CMD_KGDB) 538 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 539 #endif 540 541 /* 542 * Environment Configuration 543 */ 544 #define CONFIG_HOSTNAME mpc8569mds 545 #define CONFIG_ROOTPATH "/nfsroot" 546 #define CONFIG_BOOTFILE "your.uImage" 547 548 #define CONFIG_SERVERIP 192.168.1.1 549 #define CONFIG_GATEWAYIP 192.168.1.1 550 #define CONFIG_NETMASK 255.255.255.0 551 552 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 553 554 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 555 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 556 557 #define CONFIG_BAUDRATE 115200 558 559 #define CONFIG_EXTRA_ENV_SETTINGS \ 560 "netdev=eth0\0" \ 561 "consoledev=ttyS0\0" \ 562 "ramdiskaddr=600000\0" \ 563 "ramdiskfile=your.ramdisk.u-boot\0" \ 564 "fdtaddr=400000\0" \ 565 "fdtfile=your.fdt.dtb\0" \ 566 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 567 "nfsroot=$serverip:$rootpath " \ 568 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 569 "console=$consoledev,$baudrate $othbootargs\0" \ 570 "ramargs=setenv bootargs root=/dev/ram rw " \ 571 "console=$consoledev,$baudrate $othbootargs\0" \ 572 573 #define CONFIG_NFSBOOTCOMMAND \ 574 "run nfsargs;" \ 575 "tftp $loadaddr $bootfile;" \ 576 "tftp $fdtaddr $fdtfile;" \ 577 "bootm $loadaddr - $fdtaddr" 578 579 #define CONFIG_RAMBOOTCOMMAND \ 580 "run ramargs;" \ 581 "tftp $ramdiskaddr $ramdiskfile;" \ 582 "tftp $loadaddr $bootfile;" \ 583 "bootm $loadaddr $ramdiskaddr" 584 585 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 586 587 #endif /* __CONFIG_H */ 588