1 /* 2 * Copyright 2004-2007 Freescale Semiconductor. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8568mds board configuration file 25 */ 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* High Level Configuration Options */ 30 #define CONFIG_BOOKE 1 /* BOOKE */ 31 #define CONFIG_E500 1 /* BOOKE e500 family */ 32 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ 33 #define CONFIG_MPC8568 1 /* MPC8568 specific */ 34 #define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */ 35 36 #undef CONFIG_PCI 37 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 38 #define CONFIG_ENV_OVERWRITE 39 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 40 #define CONFIG_DDR_DLL /* possible DLL fix needed */ 41 /*#define CONFIG_DDR_2T_TIMING Sets the 2T timing bit */ 42 43 /*#define CONFIG_DDR_ECC*/ /* only for ECC DDR module */ 44 /*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */ 45 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 46 47 48 /* 49 * When initializing flash, if we cannot find the manufacturer ID, 50 * assume this is the AMD flash associated with the MDS board. 51 * This allows booting from a promjet. 52 */ 53 #define CONFIG_ASSUME_AMD_FLASH 54 55 #define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ 56 57 #ifndef __ASSEMBLY__ 58 extern unsigned long get_clock_freq(void); 59 #endif /*Replace a call to get_clock_freq (after it is implemented)*/ 60 #define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */ 61 62 /* 63 * These can be toggled for performance analysis, otherwise use default. 64 */ 65 /*#define CONFIG_L2_CACHE*/ /* toggle L2 cache */ 66 #define CONFIG_BTB /* toggle branch predition */ 67 #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ 68 69 /* 70 * Only possible on E500 Version 2 or newer cores. 71 */ 72 #define CONFIG_ENABLE_36BIT_PHYS 1 73 74 75 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 76 77 #undef CFG_DRAM_TEST /* memory test, takes time */ 78 #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ 79 #define CFG_MEMTEST_END 0x00400000 80 81 /* 82 * Base addresses -- Note these are effective addresses where the 83 * actual resources get mapped (not physical addresses) 84 */ 85 #define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 86 #define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 87 #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ 88 89 /* 90 * DDR Setup 91 */ 92 #define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 93 #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE 94 95 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ 96 97 /* 98 * Make sure required options are set 99 */ 100 #ifndef CONFIG_SPD_EEPROM 101 #error ("CONFIG_SPD_EEPROM is required") 102 #endif 103 104 #undef CONFIG_CLOCKS_IN_MHZ 105 106 107 /* 108 * Local Bus Definitions 109 */ 110 111 /* 112 * FLASH on the Local Bus 113 * Two banks, 8M each, using the CFI driver. 114 * Boot from BR0/OR0 bank at 0xff00_0000 115 * Alternate BR1/OR1 bank at 0xff80_0000 116 * 117 * BR0, BR1: 118 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 119 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 120 * Port Size = 16 bits = BRx[19:20] = 10 121 * Use GPCM = BRx[24:26] = 000 122 * Valid = BRx[31] = 1 123 * 124 * 0 4 8 12 16 20 24 28 125 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 126 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 127 * 128 * OR0, OR1: 129 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 130 * Reserved ORx[17:18] = 11, confusion here? 131 * CSNT = ORx[20] = 1 132 * ACS = half cycle delay = ORx[21:22] = 11 133 * SCY = 6 = ORx[24:27] = 0110 134 * TRLX = use relaxed timing = ORx[29] = 1 135 * EAD = use external address latch delay = OR[31] = 1 136 * 137 * 0 4 8 12 16 20 24 28 138 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 139 */ 140 #define CFG_BCSR_BASE 0xf8000000 141 142 #define CFG_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 143 144 /*Chip select 0 - Flash*/ 145 #define CFG_BR0_PRELIM 0xfe001001 146 #define CFG_OR0_PRELIM 0xfe006ff7 147 148 /*Chip slelect 1 - BCSR*/ 149 #define CFG_BR1_PRELIM 0xf8000801 150 #define CFG_OR1_PRELIM 0xffffe9f7 151 152 /*#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} */ 153 #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ 154 #define CFG_MAX_FLASH_SECT 512 /* sectors per device */ 155 #undef CFG_FLASH_CHECKSUM 156 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 157 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 158 159 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ 160 161 #define CFG_FLASH_CFI_DRIVER 162 #define CFG_FLASH_CFI 163 #define CFG_FLASH_EMPTY_INFO 164 165 166 /* 167 * SDRAM on the LocalBus 168 */ 169 #define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 170 #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 171 172 173 /*Chip select 2 - SDRAM*/ 174 #define CFG_BR2_PRELIM 0xf0001861 175 #define CFG_OR2_PRELIM 0xfc006901 176 177 #define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 178 #define CFG_LBC_LBCR 0x00000000 /* LB config reg */ 179 #define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 180 #define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 181 182 /* 183 * LSDMR masks 184 */ 185 #define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) 186 #define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) 187 #define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) 188 #define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) 189 #define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) 190 #define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) 191 #define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) 192 #define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) 193 #define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) 194 #define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) 195 196 #define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) 197 #define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) 198 #define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) 199 #define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) 200 #define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) 201 #define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) 202 #define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) 203 #define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) 204 205 /* 206 * Common settings for all Local Bus SDRAM commands. 207 * At run time, either BSMA1516 (for CPU 1.1) 208 * or BSMA1617 (for CPU 1.0) (old) 209 * is OR'ed in too. 210 */ 211 #define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \ 212 | CFG_LBC_LSDMR_PRETOACT7 \ 213 | CFG_LBC_LSDMR_ACTTORW7 \ 214 | CFG_LBC_LSDMR_BL8 \ 215 | CFG_LBC_LSDMR_WRC4 \ 216 | CFG_LBC_LSDMR_CL3 \ 217 | CFG_LBC_LSDMR_RFEN \ 218 ) 219 220 /* 221 * The bcsr registers are connected to CS3 on MDS. 222 * The new memory map places bcsr at 0xf8000000. 223 * 224 * For BR3, need: 225 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 226 * port-size = 8-bits = BR[19:20] = 01 227 * no parity checking = BR[21:22] = 00 228 * GPMC for MSEL = BR[24:26] = 000 229 * Valid = BR[31] = 1 230 * 231 * 0 4 8 12 16 20 24 28 232 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 233 * 234 * For OR3, need: 235 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 236 * disable buffer ctrl OR[19] = 0 237 * CSNT OR[20] = 1 238 * ACS OR[21:22] = 11 239 * XACS OR[23] = 1 240 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 241 * SETA OR[28] = 0 242 * TRLX OR[29] = 1 243 * EHTR OR[30] = 1 244 * EAD extra time OR[31] = 1 245 * 246 * 0 4 8 12 16 20 24 28 247 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 248 */ 249 #define CFG_BCSR (0xf8000000) 250 251 /*Chip slelect 4 - PIB*/ 252 #define CFG_BR4_PRELIM 0xf8008801 253 #define CFG_OR4_PRELIM 0xffffe9f7 254 255 /*Chip select 5 - PIB*/ 256 #define CFG_BR5_PRELIM 0xf8010801 257 #define CFG_OR5_PRELIM 0xffff69f7 258 259 #define CONFIG_L1_INIT_RAM 260 #define CFG_INIT_RAM_LOCK 1 261 #define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 262 #define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ 263 264 #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ 265 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 266 #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET 267 268 #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 269 #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 270 271 /* Serial Port */ 272 #define CONFIG_CONS_INDEX 1 273 #undef CONFIG_SERIAL_SOFTWARE_FIFO 274 #define CFG_NS16550 275 #define CFG_NS16550_SERIAL 276 #define CFG_NS16550_REG_SIZE 1 277 #define CFG_NS16550_CLK get_bus_freq(0) 278 279 #define CFG_BAUDRATE_TABLE \ 280 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 281 282 #define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) 283 #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) 284 285 /* Use the HUSH parser*/ 286 #define CFG_HUSH_PARSER 287 #ifdef CFG_HUSH_PARSER 288 #define CFG_PROMPT_HUSH_PS2 "> " 289 #endif 290 291 /* pass open firmware flat tree */ 292 #define CONFIG_OF_FLAT_TREE 1 293 #define CONFIG_OF_BOARD_SETUP 1 294 295 /* maximum size of the flat tree (8K) */ 296 #define OF_FLAT_TREE_MAX_SIZE 8192 297 298 #define OF_CPU "PowerPC,8568@0" 299 #define OF_SOC "soc8568@e0000000" 300 #define OF_TBCLK (bd->bi_busfreq / 8) 301 #define OF_STDOUT_PATH "/soc8568@e0000000/serial@4600" 302 303 /* 304 * I2C 305 */ 306 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 307 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 308 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 309 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ 310 #define CFG_I2C_EEPROM_ADDR 0x57 311 #define CFG_I2C_SLAVE 0x7F 312 #define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 313 #define CFG_I2C_OFFSET 0x3000 314 315 /* 316 * General PCI 317 * Memory Addresses are mapped 1-1. I/O is mapped from 0 318 */ 319 #define CFG_PCI1_MEM_BASE 0x80000000 320 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE 321 #define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ 322 #define CFG_PCI1_IO_BASE 0x00000000 323 #define CFG_PCI1_IO_PHYS 0xe2000000 324 #define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */ 325 326 #define CFG_PEX_MEM_BASE 0xa0000000 327 #define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE 328 #define CFG_PEX_MEM_SIZE 0x10000000 /* 256M */ 329 #define CFG_PEX_IO_BASE 0x00000000 330 #define CFG_PEX_IO_PHYS 0xe2800000 331 #define CFG_PEX_IO_SIZE 0x00800000 /* 8M */ 332 333 #define CFG_SRIO_MEM_BASE 0xc0000000 334 335 #if defined(CONFIG_PCI) 336 337 #define CONFIG_NET_MULTI 338 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 339 340 #undef CONFIG_EEPRO100 341 #undef CONFIG_TULIP 342 343 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 344 #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 345 346 #endif /* CONFIG_PCI */ 347 348 349 #if defined(CONFIG_TSEC_ENET) 350 351 #ifndef CONFIG_NET_MULTI 352 #define CONFIG_NET_MULTI 1 353 #endif 354 355 #define CONFIG_MII 1 /* MII PHY management */ 356 #define CONFIG_TSEC1 1 357 #define CONFIG_TSEC1_NAME "eTSEC0" 358 #define CONFIG_TSEC2 1 359 #define CONFIG_TSEC2_NAME "eTSEC1" 360 #undef CONFIG_TSEC3 361 #undef CONFIG_TSEC4 362 #undef CONFIG_MPC85XX_FEC 363 364 #define TSEC1_PHY_ADDR 2 365 #define TSEC2_PHY_ADDR 3 366 367 #define TSEC1_PHYIDX 0 368 #define TSEC2_PHYIDX 0 369 370 /* Options are: eTSEC[0-3] */ 371 #define CONFIG_ETHPRIME "eTSEC0" 372 373 #endif /* CONFIG_TSEC_ENET */ 374 375 /* 376 * Environment 377 */ 378 #define CFG_ENV_IS_IN_FLASH 1 379 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) 380 #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 381 #define CFG_ENV_SIZE 0x2000 382 383 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 384 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 385 386 387 /* 388 * BOOTP options 389 */ 390 #define CONFIG_BOOTP_BOOTFILESIZE 391 #define CONFIG_BOOTP_BOOTPATH 392 #define CONFIG_BOOTP_GATEWAY 393 #define CONFIG_BOOTP_HOSTNAME 394 395 396 /* 397 * Command line configuration. 398 */ 399 #include <config_cmd_default.h> 400 401 #define CONFIG_CMD_PING 402 #define CONFIG_CMD_I2C 403 #define CONFIG_CMD_MII 404 405 #if defined(CONFIG_PCI) 406 #define CONFIG_CMD_PCI 407 #endif 408 409 410 #undef CONFIG_WATCHDOG /* watchdog disabled */ 411 412 /* 413 * Miscellaneous configurable options 414 */ 415 #define CFG_LONGHELP /* undef to save memory */ 416 #define CFG_LOAD_ADDR 0x2000000 /* default load address */ 417 #define CFG_PROMPT "=> " /* Monitor Command Prompt */ 418 #if defined(CONFIG_CMD_KGDB) 419 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ 420 #else 421 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 422 #endif 423 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 424 #define CFG_MAXARGS 16 /* max number of command args */ 425 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 426 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ 427 428 /* 429 * For booting Linux, the board info and command line data 430 * have to be in the first 8 MB of memory, since this is 431 * the maximum mapped by the Linux kernel during initialization. 432 */ 433 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 434 435 /* Cache Configuration */ 436 #define CFG_DCACHE_SIZE 32768 437 #define CFG_CACHELINE_SIZE 32 438 #if defined(CONFIG_CMD_KGDB) 439 #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ 440 #endif 441 442 /* 443 * Internal Definitions 444 * 445 * Boot Flags 446 */ 447 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 448 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 449 450 #if defined(CONFIG_CMD_KGDB) 451 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 452 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 453 #endif 454 455 /* 456 * Environment Configuration 457 */ 458 459 /* The mac addresses for all ethernet interface */ 460 #if defined(CONFIG_TSEC_ENET) 461 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 462 #define CONFIG_HAS_ETH1 463 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 464 #define CONFIG_HAS_ETH2 465 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 466 #endif 467 468 #define CONFIG_IPADDR 192.168.1.253 469 470 #define CONFIG_HOSTNAME unknown 471 #define CONFIG_ROOTPATH /nfsroot 472 #define CONFIG_BOOTFILE your.uImage 473 474 #define CONFIG_SERVERIP 192.168.1.1 475 #define CONFIG_GATEWAYIP 192.168.1.1 476 #define CONFIG_NETMASK 255.255.255.0 477 478 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 479 480 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 481 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 482 483 #define CONFIG_BAUDRATE 115200 484 485 #define CONFIG_EXTRA_ENV_SETTINGS \ 486 "netdev=eth0\0" \ 487 "consoledev=ttyS0\0" \ 488 "ramdiskaddr=600000\0" \ 489 "ramdiskfile=your.ramdisk.u-boot\0" \ 490 "fdtaddr=400000\0" \ 491 "fdtfile=your.fdt.dtb\0" \ 492 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 493 "nfsroot=$serverip:$rootpath " \ 494 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 495 "console=$consoledev,$baudrate $othbootargs\0" \ 496 "ramargs=setenv bootargs root=/dev/ram rw " \ 497 "console=$consoledev,$baudrate $othbootargs\0" \ 498 499 500 #define CONFIG_NFSBOOTCOMMAND \ 501 "run nfsargs;" \ 502 "tftp $loadaddr $bootfile;" \ 503 "tftp $fdtaddr $fdtfile;" \ 504 "bootm $loadaddr - $fdtaddr" 505 506 507 #define CONFIG_RAMBOOTCOMMAND \ 508 "run ramargs;" \ 509 "tftp $ramdiskaddr $ramdiskfile;" \ 510 "tftp $loadaddr $bootfile;" \ 511 "bootm $loadaddr $ramdiskaddr" 512 513 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 514 515 #endif /* __CONFIG_H */ 516