1 /* 2 * Copyright 2004-2007, 2010-2011 Freescale Semiconductor. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8568mds board configuration file 9 */ 10 #ifndef __CONFIG_H 11 #define __CONFIG_H 12 13 /* High Level Configuration Options */ 14 #define CONFIG_BOOKE 1 /* BOOKE */ 15 #define CONFIG_E500 1 /* BOOKE e500 family */ 16 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ 17 #define CONFIG_MPC8568 1 /* MPC8568 specific */ 18 #define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */ 19 20 #define CONFIG_SYS_TEXT_BASE 0xfff80000 21 22 #define CONFIG_SYS_SRIO 23 #define CONFIG_SRIO1 /* SRIO port 1 */ 24 25 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 26 #define CONFIG_PCI1 1 /* PCI controller */ 27 #define CONFIG_PCIE1 1 /* PCIE controller */ 28 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 29 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 30 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 31 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 32 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 33 #define CONFIG_QE /* Enable QE */ 34 #define CONFIG_ENV_OVERWRITE 35 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 36 37 #ifndef __ASSEMBLY__ 38 extern unsigned long get_clock_freq(void); 39 #endif /*Replace a call to get_clock_freq (after it is implemented)*/ 40 #define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */ 41 42 /* 43 * These can be toggled for performance analysis, otherwise use default. 44 */ 45 #define CONFIG_L2_CACHE /* toggle L2 cache */ 46 #define CONFIG_BTB /* toggle branch predition */ 47 48 /* 49 * Only possible on E500 Version 2 or newer cores. 50 */ 51 #define CONFIG_ENABLE_36BIT_PHYS 1 52 53 54 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 55 56 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 57 #define CONFIG_SYS_MEMTEST_END 0x00400000 58 59 #define CONFIG_SYS_CCSRBAR 0xe0000000 60 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 61 62 /* DDR Setup */ 63 #define CONFIG_SYS_FSL_DDR2 64 #undef CONFIG_FSL_DDR_INTERACTIVE 65 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 66 #define CONFIG_DDR_SPD 67 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 68 69 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 70 71 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 72 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 73 74 #define CONFIG_NUM_DDR_CONTROLLERS 1 75 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 76 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 77 78 /* I2C addresses of SPD EEPROMs */ 79 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 80 81 /* Make sure required options are set */ 82 #ifndef CONFIG_SPD_EEPROM 83 #error ("CONFIG_SPD_EEPROM is required") 84 #endif 85 86 #undef CONFIG_CLOCKS_IN_MHZ 87 88 /* 89 * Local Bus Definitions 90 */ 91 92 /* 93 * FLASH on the Local Bus 94 * Two banks, 8M each, using the CFI driver. 95 * Boot from BR0/OR0 bank at 0xff00_0000 96 * Alternate BR1/OR1 bank at 0xff80_0000 97 * 98 * BR0, BR1: 99 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 100 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 101 * Port Size = 16 bits = BRx[19:20] = 10 102 * Use GPCM = BRx[24:26] = 000 103 * Valid = BRx[31] = 1 104 * 105 * 0 4 8 12 16 20 24 28 106 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 107 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 108 * 109 * OR0, OR1: 110 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 111 * Reserved ORx[17:18] = 11, confusion here? 112 * CSNT = ORx[20] = 1 113 * ACS = half cycle delay = ORx[21:22] = 11 114 * SCY = 6 = ORx[24:27] = 0110 115 * TRLX = use relaxed timing = ORx[29] = 1 116 * EAD = use external address latch delay = OR[31] = 1 117 * 118 * 0 4 8 12 16 20 24 28 119 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 120 */ 121 #define CONFIG_SYS_BCSR_BASE 0xf8000000 122 123 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 124 125 /*Chip select 0 - Flash*/ 126 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 127 #define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 128 129 /*Chip slelect 1 - BCSR*/ 130 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 131 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 132 133 /*#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} */ 134 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 135 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 136 #undef CONFIG_SYS_FLASH_CHECKSUM 137 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 138 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 139 140 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 141 142 #define CONFIG_FLASH_CFI_DRIVER 143 #define CONFIG_SYS_FLASH_CFI 144 #define CONFIG_SYS_FLASH_EMPTY_INFO 145 146 147 /* 148 * SDRAM on the LocalBus 149 */ 150 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 151 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 152 153 154 /*Chip select 2 - SDRAM*/ 155 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 156 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 157 158 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 159 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 160 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 161 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 162 163 /* 164 * Common settings for all Local Bus SDRAM commands. 165 * At run time, either BSMA1516 (for CPU 1.1) 166 * or BSMA1617 (for CPU 1.0) (old) 167 * is OR'ed in too. 168 */ 169 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 170 | LSDMR_PRETOACT7 \ 171 | LSDMR_ACTTORW7 \ 172 | LSDMR_BL8 \ 173 | LSDMR_WRC4 \ 174 | LSDMR_CL3 \ 175 | LSDMR_RFEN \ 176 ) 177 178 /* 179 * The bcsr registers are connected to CS3 on MDS. 180 * The new memory map places bcsr at 0xf8000000. 181 * 182 * For BR3, need: 183 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 184 * port-size = 8-bits = BR[19:20] = 01 185 * no parity checking = BR[21:22] = 00 186 * GPMC for MSEL = BR[24:26] = 000 187 * Valid = BR[31] = 1 188 * 189 * 0 4 8 12 16 20 24 28 190 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 191 * 192 * For OR3, need: 193 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 194 * disable buffer ctrl OR[19] = 0 195 * CSNT OR[20] = 1 196 * ACS OR[21:22] = 11 197 * XACS OR[23] = 1 198 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 199 * SETA OR[28] = 0 200 * TRLX OR[29] = 1 201 * EHTR OR[30] = 1 202 * EAD extra time OR[31] = 1 203 * 204 * 0 4 8 12 16 20 24 28 205 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 206 */ 207 #define CONFIG_SYS_BCSR (0xf8000000) 208 209 /*Chip slelect 4 - PIB*/ 210 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 211 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 212 213 /*Chip select 5 - PIB*/ 214 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 215 #define CONFIG_SYS_OR5_PRELIM 0xffff69f7 216 217 #define CONFIG_SYS_INIT_RAM_LOCK 1 218 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 219 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 220 221 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 222 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 223 224 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 225 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 226 227 /* Serial Port */ 228 #define CONFIG_CONS_INDEX 1 229 #define CONFIG_SYS_NS16550 230 #define CONFIG_SYS_NS16550_SERIAL 231 #define CONFIG_SYS_NS16550_REG_SIZE 1 232 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 233 234 #define CONFIG_SYS_BAUDRATE_TABLE \ 235 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 236 237 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 238 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 239 240 /* Use the HUSH parser*/ 241 #define CONFIG_SYS_HUSH_PARSER 242 #ifdef CONFIG_SYS_HUSH_PARSER 243 #endif 244 245 /* pass open firmware flat tree */ 246 #define CONFIG_OF_LIBFDT 1 247 #define CONFIG_OF_BOARD_SETUP 1 248 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 249 250 /* 251 * I2C 252 */ 253 #define CONFIG_SYS_I2C 254 #define CONFIG_SYS_I2C_FSL 255 #define CONFIG_SYS_FSL_I2C_SPEED 400000 256 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 257 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 258 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 259 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 260 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 261 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 262 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 263 264 /* 265 * General PCI 266 * Memory Addresses are mapped 1-1. I/O is mapped from 0 267 */ 268 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 269 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 270 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 271 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 272 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 273 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 274 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 275 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */ 276 277 #define CONFIG_SYS_PCIE1_NAME "Slot" 278 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 279 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 280 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 281 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 282 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 283 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 284 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 285 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 286 287 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 288 #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 289 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS 290 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 291 292 #ifdef CONFIG_QE 293 /* 294 * QE UEC ethernet configuration 295 */ 296 #define CONFIG_UEC_ETH 297 #ifndef CONFIG_TSEC_ENET 298 #define CONFIG_ETHPRIME "UEC0" 299 #endif 300 #define CONFIG_PHY_MODE_NEED_CHANGE 301 #define CONFIG_eTSEC_MDIO_BUS 302 303 #ifdef CONFIG_eTSEC_MDIO_BUS 304 #define CONFIG_MIIM_ADDRESS 0xE0024520 305 #endif 306 307 #define CONFIG_UEC_ETH1 /* GETH1 */ 308 309 #ifdef CONFIG_UEC_ETH1 310 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 311 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 312 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 313 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 314 #define CONFIG_SYS_UEC1_PHY_ADDR 7 315 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 316 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 317 #endif 318 319 #define CONFIG_UEC_ETH2 /* GETH2 */ 320 321 #ifdef CONFIG_UEC_ETH2 322 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 323 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 324 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 325 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 326 #define CONFIG_SYS_UEC2_PHY_ADDR 1 327 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID 328 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 329 #endif 330 #endif /* CONFIG_QE */ 331 332 #if defined(CONFIG_PCI) 333 334 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 335 336 #undef CONFIG_EEPRO100 337 #undef CONFIG_TULIP 338 339 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 340 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 341 342 #endif /* CONFIG_PCI */ 343 344 #if defined(CONFIG_TSEC_ENET) 345 346 #define CONFIG_MII 1 /* MII PHY management */ 347 #define CONFIG_TSEC1 1 348 #define CONFIG_TSEC1_NAME "eTSEC0" 349 #define CONFIG_TSEC2 1 350 #define CONFIG_TSEC2_NAME "eTSEC1" 351 352 #define TSEC1_PHY_ADDR 2 353 #define TSEC2_PHY_ADDR 3 354 355 #define TSEC1_PHYIDX 0 356 #define TSEC2_PHYIDX 0 357 358 #define TSEC1_FLAGS TSEC_GIGABIT 359 #define TSEC2_FLAGS TSEC_GIGABIT 360 361 /* Options are: eTSEC[0-1] */ 362 #define CONFIG_ETHPRIME "eTSEC0" 363 364 #endif /* CONFIG_TSEC_ENET */ 365 366 /* 367 * Environment 368 */ 369 #define CONFIG_ENV_IS_IN_FLASH 1 370 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 371 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 372 #define CONFIG_ENV_SIZE 0x2000 373 374 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 375 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 376 377 378 /* 379 * BOOTP options 380 */ 381 #define CONFIG_BOOTP_BOOTFILESIZE 382 #define CONFIG_BOOTP_BOOTPATH 383 #define CONFIG_BOOTP_GATEWAY 384 #define CONFIG_BOOTP_HOSTNAME 385 386 387 /* 388 * Command line configuration. 389 */ 390 #include <config_cmd_default.h> 391 392 #define CONFIG_CMD_PING 393 #define CONFIG_CMD_I2C 394 #define CONFIG_CMD_MII 395 #define CONFIG_CMD_ELF 396 #define CONFIG_CMD_IRQ 397 #define CONFIG_CMD_SETEXPR 398 #define CONFIG_CMD_REGINFO 399 400 #if defined(CONFIG_PCI) 401 #define CONFIG_CMD_PCI 402 #endif 403 404 405 #undef CONFIG_WATCHDOG /* watchdog disabled */ 406 407 /* 408 * Miscellaneous configurable options 409 */ 410 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 411 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 412 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 413 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 414 #if defined(CONFIG_CMD_KGDB) 415 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 416 #else 417 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 418 #endif 419 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 420 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 421 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 422 423 /* 424 * For booting Linux, the board info and command line data 425 * have to be in the first 64 MB of memory, since this is 426 * the maximum mapped by the Linux kernel during initialization. 427 */ 428 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 429 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 430 431 #if defined(CONFIG_CMD_KGDB) 432 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 433 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 434 #endif 435 436 /* 437 * Environment Configuration 438 */ 439 440 /* The mac addresses for all ethernet interface */ 441 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH) 442 #define CONFIG_HAS_ETH0 443 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 444 #define CONFIG_HAS_ETH1 445 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 446 #define CONFIG_HAS_ETH2 447 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 448 #define CONFIG_HAS_ETH3 449 #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD 450 #endif 451 452 #define CONFIG_IPADDR 192.168.1.253 453 454 #define CONFIG_HOSTNAME unknown 455 #define CONFIG_ROOTPATH "/nfsroot" 456 #define CONFIG_BOOTFILE "your.uImage" 457 458 #define CONFIG_SERVERIP 192.168.1.1 459 #define CONFIG_GATEWAYIP 192.168.1.1 460 #define CONFIG_NETMASK 255.255.255.0 461 462 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 463 464 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 465 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 466 467 #define CONFIG_BAUDRATE 115200 468 469 #define CONFIG_EXTRA_ENV_SETTINGS \ 470 "netdev=eth0\0" \ 471 "consoledev=ttyS0\0" \ 472 "ramdiskaddr=600000\0" \ 473 "ramdiskfile=your.ramdisk.u-boot\0" \ 474 "fdtaddr=400000\0" \ 475 "fdtfile=your.fdt.dtb\0" \ 476 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 477 "nfsroot=$serverip:$rootpath " \ 478 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 479 "console=$consoledev,$baudrate $othbootargs\0" \ 480 "ramargs=setenv bootargs root=/dev/ram rw " \ 481 "console=$consoledev,$baudrate $othbootargs\0" \ 482 483 484 #define CONFIG_NFSBOOTCOMMAND \ 485 "run nfsargs;" \ 486 "tftp $loadaddr $bootfile;" \ 487 "tftp $fdtaddr $fdtfile;" \ 488 "bootm $loadaddr - $fdtaddr" 489 490 491 #define CONFIG_RAMBOOTCOMMAND \ 492 "run ramargs;" \ 493 "tftp $ramdiskaddr $ramdiskfile;" \ 494 "tftp $loadaddr $bootfile;" \ 495 "bootm $loadaddr $ramdiskaddr" 496 497 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 498 499 #endif /* __CONFIG_H */ 500