1 /* 2 * Copyright 2004-2007, 2010-2011 Freescale Semiconductor. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8568mds board configuration file 25 */ 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* High Level Configuration Options */ 30 #define CONFIG_BOOKE 1 /* BOOKE */ 31 #define CONFIG_E500 1 /* BOOKE e500 family */ 32 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ 33 #define CONFIG_MPC8568 1 /* MPC8568 specific */ 34 #define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */ 35 36 #define CONFIG_SYS_TEXT_BASE 0xfff80000 37 38 #define CONFIG_SYS_SRIO 39 #define CONFIG_SRIO1 /* SRIO port 1 */ 40 41 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 42 #define CONFIG_PCI1 1 /* PCI controller */ 43 #define CONFIG_PCIE1 1 /* PCIE controller */ 44 #define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ 45 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 46 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 47 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 48 #define CONFIG_QE /* Enable QE */ 49 #define CONFIG_ENV_OVERWRITE 50 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 51 52 #ifndef __ASSEMBLY__ 53 extern unsigned long get_clock_freq(void); 54 #endif /*Replace a call to get_clock_freq (after it is implemented)*/ 55 #define CONFIG_SYS_CLK_FREQ 66000000 /*TODO: restore if wanting to read from BCSR: get_clock_freq()*/ /* sysclk for MPC85xx */ 56 57 /* 58 * These can be toggled for performance analysis, otherwise use default. 59 */ 60 #define CONFIG_L2_CACHE /* toggle L2 cache */ 61 #define CONFIG_BTB /* toggle branch predition */ 62 63 /* 64 * Only possible on E500 Version 2 or newer cores. 65 */ 66 #define CONFIG_ENABLE_36BIT_PHYS 1 67 68 69 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 70 71 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 72 #define CONFIG_SYS_MEMTEST_END 0x00400000 73 74 /* 75 * Base addresses -- Note these are effective addresses where the 76 * actual resources get mapped (not physical addresses) 77 */ 78 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 79 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 80 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 81 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 82 83 /* DDR Setup */ 84 #define CONFIG_FSL_DDR2 85 #undef CONFIG_FSL_DDR_INTERACTIVE 86 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 87 #define CONFIG_DDR_SPD 88 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 89 90 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 91 92 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 93 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 94 95 #define CONFIG_NUM_DDR_CONTROLLERS 1 96 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 97 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 98 99 /* I2C addresses of SPD EEPROMs */ 100 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 101 102 /* Make sure required options are set */ 103 #ifndef CONFIG_SPD_EEPROM 104 #error ("CONFIG_SPD_EEPROM is required") 105 #endif 106 107 #undef CONFIG_CLOCKS_IN_MHZ 108 109 /* 110 * Local Bus Definitions 111 */ 112 113 /* 114 * FLASH on the Local Bus 115 * Two banks, 8M each, using the CFI driver. 116 * Boot from BR0/OR0 bank at 0xff00_0000 117 * Alternate BR1/OR1 bank at 0xff80_0000 118 * 119 * BR0, BR1: 120 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 121 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 122 * Port Size = 16 bits = BRx[19:20] = 10 123 * Use GPCM = BRx[24:26] = 000 124 * Valid = BRx[31] = 1 125 * 126 * 0 4 8 12 16 20 24 28 127 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 128 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 129 * 130 * OR0, OR1: 131 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 132 * Reserved ORx[17:18] = 11, confusion here? 133 * CSNT = ORx[20] = 1 134 * ACS = half cycle delay = ORx[21:22] = 11 135 * SCY = 6 = ORx[24:27] = 0110 136 * TRLX = use relaxed timing = ORx[29] = 1 137 * EAD = use external address latch delay = OR[31] = 1 138 * 139 * 0 4 8 12 16 20 24 28 140 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 141 */ 142 #define CONFIG_SYS_BCSR_BASE 0xf8000000 143 144 #define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ 145 146 /*Chip select 0 - Flash*/ 147 #define CONFIG_SYS_BR0_PRELIM 0xfe001001 148 #define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 149 150 /*Chip slelect 1 - BCSR*/ 151 #define CONFIG_SYS_BR1_PRELIM 0xf8000801 152 #define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 153 154 /*#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} */ 155 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 156 #define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ 157 #undef CONFIG_SYS_FLASH_CHECKSUM 158 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 159 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 160 161 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 162 163 #define CONFIG_FLASH_CFI_DRIVER 164 #define CONFIG_SYS_FLASH_CFI 165 #define CONFIG_SYS_FLASH_EMPTY_INFO 166 167 168 /* 169 * SDRAM on the LocalBus 170 */ 171 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 172 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 173 174 175 /*Chip select 2 - SDRAM*/ 176 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 177 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 178 179 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 180 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 181 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 182 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 183 184 /* 185 * Common settings for all Local Bus SDRAM commands. 186 * At run time, either BSMA1516 (for CPU 1.1) 187 * or BSMA1617 (for CPU 1.0) (old) 188 * is OR'ed in too. 189 */ 190 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 191 | LSDMR_PRETOACT7 \ 192 | LSDMR_ACTTORW7 \ 193 | LSDMR_BL8 \ 194 | LSDMR_WRC4 \ 195 | LSDMR_CL3 \ 196 | LSDMR_RFEN \ 197 ) 198 199 /* 200 * The bcsr registers are connected to CS3 on MDS. 201 * The new memory map places bcsr at 0xf8000000. 202 * 203 * For BR3, need: 204 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 205 * port-size = 8-bits = BR[19:20] = 01 206 * no parity checking = BR[21:22] = 00 207 * GPMC for MSEL = BR[24:26] = 000 208 * Valid = BR[31] = 1 209 * 210 * 0 4 8 12 16 20 24 28 211 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 212 * 213 * For OR3, need: 214 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 215 * disable buffer ctrl OR[19] = 0 216 * CSNT OR[20] = 1 217 * ACS OR[21:22] = 11 218 * XACS OR[23] = 1 219 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 220 * SETA OR[28] = 0 221 * TRLX OR[29] = 1 222 * EHTR OR[30] = 1 223 * EAD extra time OR[31] = 1 224 * 225 * 0 4 8 12 16 20 24 28 226 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 227 */ 228 #define CONFIG_SYS_BCSR (0xf8000000) 229 230 /*Chip slelect 4 - PIB*/ 231 #define CONFIG_SYS_BR4_PRELIM 0xf8008801 232 #define CONFIG_SYS_OR4_PRELIM 0xffffe9f7 233 234 /*Chip select 5 - PIB*/ 235 #define CONFIG_SYS_BR5_PRELIM 0xf8010801 236 #define CONFIG_SYS_OR5_PRELIM 0xffff69f7 237 238 #define CONFIG_SYS_INIT_RAM_LOCK 1 239 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 240 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 241 242 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 243 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 244 245 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 246 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 247 248 /* Serial Port */ 249 #define CONFIG_CONS_INDEX 1 250 #define CONFIG_SYS_NS16550 251 #define CONFIG_SYS_NS16550_SERIAL 252 #define CONFIG_SYS_NS16550_REG_SIZE 1 253 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 254 255 #define CONFIG_SYS_BAUDRATE_TABLE \ 256 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 257 258 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 259 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 260 261 /* Use the HUSH parser*/ 262 #define CONFIG_SYS_HUSH_PARSER 263 #ifdef CONFIG_SYS_HUSH_PARSER 264 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 265 #endif 266 267 /* pass open firmware flat tree */ 268 #define CONFIG_OF_LIBFDT 1 269 #define CONFIG_OF_BOARD_SETUP 1 270 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 271 272 /* 273 * I2C 274 */ 275 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 276 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 277 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 278 #define CONFIG_I2C_MULTI_BUS 279 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 280 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 281 #define CONFIG_SYS_I2C_SLAVE 0x7F 282 #define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ 283 #define CONFIG_SYS_I2C_OFFSET 0x3000 284 #define CONFIG_SYS_I2C2_OFFSET 0x3100 285 286 /* 287 * General PCI 288 * Memory Addresses are mapped 1-1. I/O is mapped from 0 289 */ 290 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 291 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 292 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 293 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 294 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 295 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 296 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 297 #define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */ 298 299 #define CONFIG_SYS_PCIE1_NAME "Slot" 300 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 301 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 302 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 303 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 304 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 305 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 306 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 307 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 308 309 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xC0000000 310 #define CONFIG_SYS_SRIO1_MEM_BUS 0xC0000000 311 #define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BUS 312 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 313 314 #ifdef CONFIG_QE 315 /* 316 * QE UEC ethernet configuration 317 */ 318 #define CONFIG_UEC_ETH 319 #ifndef CONFIG_TSEC_ENET 320 #define CONFIG_ETHPRIME "UEC0" 321 #endif 322 #define CONFIG_PHY_MODE_NEED_CHANGE 323 #define CONFIG_eTSEC_MDIO_BUS 324 325 #ifdef CONFIG_eTSEC_MDIO_BUS 326 #define CONFIG_MIIM_ADDRESS 0xE0024520 327 #endif 328 329 #define CONFIG_UEC_ETH1 /* GETH1 */ 330 331 #ifdef CONFIG_UEC_ETH1 332 #define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ 333 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE 334 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK16 335 #define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH 336 #define CONFIG_SYS_UEC1_PHY_ADDR 7 337 #define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID 338 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 339 #endif 340 341 #define CONFIG_UEC_ETH2 /* GETH2 */ 342 343 #ifdef CONFIG_UEC_ETH2 344 #define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ 345 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE 346 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK16 347 #define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH 348 #define CONFIG_SYS_UEC2_PHY_ADDR 1 349 #define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID 350 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 351 #endif 352 #endif /* CONFIG_QE */ 353 354 #if defined(CONFIG_PCI) 355 356 #define CONFIG_NET_MULTI 357 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 358 359 #undef CONFIG_EEPRO100 360 #undef CONFIG_TULIP 361 362 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 363 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 364 365 #endif /* CONFIG_PCI */ 366 367 #ifndef CONFIG_NET_MULTI 368 #define CONFIG_NET_MULTI 1 369 #endif 370 371 #if defined(CONFIG_TSEC_ENET) 372 373 #define CONFIG_MII 1 /* MII PHY management */ 374 #define CONFIG_TSEC1 1 375 #define CONFIG_TSEC1_NAME "eTSEC0" 376 #define CONFIG_TSEC2 1 377 #define CONFIG_TSEC2_NAME "eTSEC1" 378 379 #define TSEC1_PHY_ADDR 2 380 #define TSEC2_PHY_ADDR 3 381 382 #define TSEC1_PHYIDX 0 383 #define TSEC2_PHYIDX 0 384 385 #define TSEC1_FLAGS TSEC_GIGABIT 386 #define TSEC2_FLAGS TSEC_GIGABIT 387 388 /* Options are: eTSEC[0-1] */ 389 #define CONFIG_ETHPRIME "eTSEC0" 390 391 #endif /* CONFIG_TSEC_ENET */ 392 393 /* 394 * Environment 395 */ 396 #define CONFIG_ENV_IS_IN_FLASH 1 397 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 398 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 399 #define CONFIG_ENV_SIZE 0x2000 400 401 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 402 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 403 404 405 /* 406 * BOOTP options 407 */ 408 #define CONFIG_BOOTP_BOOTFILESIZE 409 #define CONFIG_BOOTP_BOOTPATH 410 #define CONFIG_BOOTP_GATEWAY 411 #define CONFIG_BOOTP_HOSTNAME 412 413 414 /* 415 * Command line configuration. 416 */ 417 #include <config_cmd_default.h> 418 419 #define CONFIG_CMD_PING 420 #define CONFIG_CMD_I2C 421 #define CONFIG_CMD_MII 422 #define CONFIG_CMD_ELF 423 #define CONFIG_CMD_IRQ 424 #define CONFIG_CMD_SETEXPR 425 #define CONFIG_CMD_REGINFO 426 427 #if defined(CONFIG_PCI) 428 #define CONFIG_CMD_PCI 429 #endif 430 431 432 #undef CONFIG_WATCHDOG /* watchdog disabled */ 433 434 /* 435 * Miscellaneous configurable options 436 */ 437 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 438 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 439 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 440 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 441 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 442 #if defined(CONFIG_CMD_KGDB) 443 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 444 #else 445 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 446 #endif 447 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 448 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 449 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 450 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 451 452 /* 453 * For booting Linux, the board info and command line data 454 * have to be in the first 16 MB of memory, since this is 455 * the maximum mapped by the Linux kernel during initialization. 456 */ 457 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 458 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 459 460 #if defined(CONFIG_CMD_KGDB) 461 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 462 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 463 #endif 464 465 /* 466 * Environment Configuration 467 */ 468 469 /* The mac addresses for all ethernet interface */ 470 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH) 471 #define CONFIG_HAS_ETH0 472 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 473 #define CONFIG_HAS_ETH1 474 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 475 #define CONFIG_HAS_ETH2 476 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 477 #define CONFIG_HAS_ETH3 478 #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD 479 #endif 480 481 #define CONFIG_IPADDR 192.168.1.253 482 483 #define CONFIG_HOSTNAME unknown 484 #define CONFIG_ROOTPATH /nfsroot 485 #define CONFIG_BOOTFILE your.uImage 486 487 #define CONFIG_SERVERIP 192.168.1.1 488 #define CONFIG_GATEWAYIP 192.168.1.1 489 #define CONFIG_NETMASK 255.255.255.0 490 491 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 492 493 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 494 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 495 496 #define CONFIG_BAUDRATE 115200 497 498 #define CONFIG_EXTRA_ENV_SETTINGS \ 499 "netdev=eth0\0" \ 500 "consoledev=ttyS0\0" \ 501 "ramdiskaddr=600000\0" \ 502 "ramdiskfile=your.ramdisk.u-boot\0" \ 503 "fdtaddr=400000\0" \ 504 "fdtfile=your.fdt.dtb\0" \ 505 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 506 "nfsroot=$serverip:$rootpath " \ 507 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 508 "console=$consoledev,$baudrate $othbootargs\0" \ 509 "ramargs=setenv bootargs root=/dev/ram rw " \ 510 "console=$consoledev,$baudrate $othbootargs\0" \ 511 512 513 #define CONFIG_NFSBOOTCOMMAND \ 514 "run nfsargs;" \ 515 "tftp $loadaddr $bootfile;" \ 516 "tftp $fdtaddr $fdtfile;" \ 517 "bootm $loadaddr - $fdtaddr" 518 519 520 #define CONFIG_RAMBOOTCOMMAND \ 521 "run ramargs;" \ 522 "tftp $ramdiskaddr $ramdiskfile;" \ 523 "tftp $loadaddr $bootfile;" \ 524 "bootm $loadaddr $ramdiskaddr" 525 526 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 527 528 #endif /* __CONFIG_H */ 529