1 /* 2 * Copyright 2004 Freescale Semiconductor. 3 * (C) Copyright 2002,2003 Motorola,Inc. 4 * Xianghua Xiao <X.Xiao@motorola.com> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 /* 26 * mpc8560ads board configuration file 27 * 28 * Please refer to doc/README.mpc85xx for more info. 29 * 30 * Make sure you change the MAC address and other network params first, 31 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. 32 */ 33 34 #ifndef __CONFIG_H 35 #define __CONFIG_H 36 37 /* High Level Configuration Options */ 38 #define CONFIG_BOOKE 1 /* BOOKE */ 39 #define CONFIG_E500 1 /* BOOKE e500 family */ 40 #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ 41 #define CONFIG_CPM2 1 /* has CPM2 */ 42 #define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ 43 #define CONFIG_MPC8560 1 44 45 #define CONFIG_PCI 46 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 47 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 48 #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ 49 #define CONFIG_ENV_OVERWRITE 50 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 51 52 /* 53 * sysclk for MPC85xx 54 * 55 * Two valid values are: 56 * 33000000 57 * 66000000 58 * 59 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 60 * is likely the desired value here, so that is now the default. 61 * The board, however, can run at 66MHz. In any event, this value 62 * must match the settings of some switches. Details can be found 63 * in the README.mpc85xxads. 64 */ 65 66 #ifndef CONFIG_SYS_CLK_FREQ 67 #define CONFIG_SYS_CLK_FREQ 33000000 68 #endif 69 70 71 /* 72 * These can be toggled for performance analysis, otherwise use default. 73 */ 74 #define CONFIG_L2_CACHE /* toggle L2 cache */ 75 #define CONFIG_BTB /* toggle branch predition */ 76 77 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 78 79 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 80 #define CONFIG_SYS_MEMTEST_END 0x00400000 81 82 83 /* 84 * Base addresses -- Note these are effective addresses where the 85 * actual resources get mapped (not physical addresses) 86 */ 87 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 88 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 89 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 90 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 91 92 /* DDR Setup */ 93 #define CONFIG_FSL_DDR1 94 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 95 #define CONFIG_DDR_SPD 96 #undef CONFIG_FSL_DDR_INTERACTIVE 97 98 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 99 100 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 101 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 102 103 #define CONFIG_NUM_DDR_CONTROLLERS 1 104 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 105 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 106 107 /* I2C addresses of SPD EEPROMs */ 108 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 109 110 /* These are used when DDR doesn't use SPD. */ 111 #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ 112 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ 113 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 114 #define CONFIG_SYS_DDR_TIMING_1 0x37344321 115 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 116 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 117 #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ 118 #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ 119 120 /* 121 * SDRAM on the Local Bus 122 */ 123 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 124 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 125 126 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 127 #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ 128 129 #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ 130 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 131 #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ 132 #undef CONFIG_SYS_FLASH_CHECKSUM 133 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 134 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 135 136 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ 137 138 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 139 #define CONFIG_SYS_RAMBOOT 140 #else 141 #undef CONFIG_SYS_RAMBOOT 142 #endif 143 144 #define CONFIG_FLASH_CFI_DRIVER 145 #define CONFIG_SYS_FLASH_CFI 146 #define CONFIG_SYS_FLASH_EMPTY_INFO 147 148 #undef CONFIG_CLOCKS_IN_MHZ 149 150 151 /* 152 * Local Bus Definitions 153 */ 154 155 /* 156 * Base Register 2 and Option Register 2 configure SDRAM. 157 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 158 * 159 * For BR2, need: 160 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 161 * port-size = 32-bits = BR2[19:20] = 11 162 * no parity checking = BR2[21:22] = 00 163 * SDRAM for MSEL = BR2[24:26] = 011 164 * Valid = BR[31] = 1 165 * 166 * 0 4 8 12 16 20 24 28 167 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 168 * 169 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 170 * FIXME: the top 17 bits of BR2. 171 */ 172 173 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 174 175 /* 176 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 177 * 178 * For OR2, need: 179 * 64MB mask for AM, OR2[0:7] = 1111 1100 180 * XAM, OR2[17:18] = 11 181 * 9 columns OR2[19-21] = 010 182 * 13 rows OR2[23-25] = 100 183 * EAD set for extra time OR[31] = 1 184 * 185 * 0 4 8 12 16 20 24 28 186 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 187 */ 188 189 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 190 191 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 192 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 193 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 194 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ 195 196 /* 197 * LSDMR masks 198 */ 199 #define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1)) 200 #define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) 201 #define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) 202 #define CONFIG_SYS_LBC_LSDMR_RFCR5 (3 << (31 - 16)) 203 #define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16)) 204 #define CONFIG_SYS_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) 205 #define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) 206 #define CONFIG_SYS_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) 207 #define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) 208 #define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) 209 #define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23)) 210 #define CONFIG_SYS_LBC_LSDMR_WRC2 (2 << (31 - 27)) 211 #define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27)) 212 #define CONFIG_SYS_LBC_LSDMR_BUFCMD (1 << (31 - 29)) 213 #define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31)) 214 215 #define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) 216 #define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) 217 #define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) 218 #define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4)) 219 #define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) 220 #define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) 221 #define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) 222 #define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) 223 224 #define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_BSMA1516 \ 225 | CONFIG_SYS_LBC_LSDMR_RFCR5 \ 226 | CONFIG_SYS_LBC_LSDMR_PRETOACT3 \ 227 | CONFIG_SYS_LBC_LSDMR_ACTTORW3 \ 228 | CONFIG_SYS_LBC_LSDMR_BL8 \ 229 | CONFIG_SYS_LBC_LSDMR_WRC2 \ 230 | CONFIG_SYS_LBC_LSDMR_CL3 \ 231 | CONFIG_SYS_LBC_LSDMR_RFEN \ 232 ) 233 234 /* 235 * SDRAM Controller configuration sequence. 236 */ 237 #define CONFIG_SYS_LBC_LSDMR_1 ( CONFIG_SYS_LBC_LSDMR_COMMON \ 238 | CONFIG_SYS_LBC_LSDMR_OP_PCHALL) 239 #define CONFIG_SYS_LBC_LSDMR_2 ( CONFIG_SYS_LBC_LSDMR_COMMON \ 240 | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) 241 #define CONFIG_SYS_LBC_LSDMR_3 ( CONFIG_SYS_LBC_LSDMR_COMMON \ 242 | CONFIG_SYS_LBC_LSDMR_OP_ARFRSH) 243 #define CONFIG_SYS_LBC_LSDMR_4 ( CONFIG_SYS_LBC_LSDMR_COMMON \ 244 | CONFIG_SYS_LBC_LSDMR_OP_MRW) 245 #define CONFIG_SYS_LBC_LSDMR_5 ( CONFIG_SYS_LBC_LSDMR_COMMON \ 246 | CONFIG_SYS_LBC_LSDMR_OP_NORMAL) 247 248 249 /* 250 * 32KB, 8-bit wide for ADS config reg 251 */ 252 #define CONFIG_SYS_BR4_PRELIM 0xf8000801 253 #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 254 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) 255 256 #define CONFIG_SYS_INIT_RAM_LOCK 1 257 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 258 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ 259 260 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 261 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 262 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 263 264 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 265 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 266 267 /* Serial Port */ 268 #define CONFIG_CONS_ON_SCC /* define if console on SCC */ 269 #undef CONFIG_CONS_NONE /* define if console on something else */ 270 #define CONFIG_CONS_INDEX 1 /* which serial channel for console */ 271 272 #define CONFIG_BAUDRATE 115200 273 274 #define CONFIG_SYS_BAUDRATE_TABLE \ 275 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 276 277 /* Use the HUSH parser */ 278 #define CONFIG_SYS_HUSH_PARSER 279 #ifdef CONFIG_SYS_HUSH_PARSER 280 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 281 #endif 282 283 /* pass open firmware flat tree */ 284 #define CONFIG_OF_LIBFDT 1 285 #define CONFIG_OF_BOARD_SETUP 1 286 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 287 288 #define CONFIG_SYS_64BIT_VSPRINTF 1 289 #define CONFIG_SYS_64BIT_STRTOUL 1 290 291 /* 292 * I2C 293 */ 294 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 295 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 296 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 297 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 298 #define CONFIG_SYS_I2C_SLAVE 0x7F 299 #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 300 #define CONFIG_SYS_I2C_OFFSET 0x3000 301 302 /* RapidIO MMU */ 303 #define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ 304 #define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE 305 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ 306 307 /* 308 * General PCI 309 * Memory space is mapped 1-1, but I/O space must start from 0. 310 */ 311 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 312 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 313 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 314 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 315 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 316 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 317 318 #if defined(CONFIG_PCI) 319 320 #define CONFIG_NET_MULTI 321 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 322 323 #undef CONFIG_EEPRO100 324 #undef CONFIG_TULIP 325 326 #if !defined(CONFIG_PCI_PNP) 327 #define PCI_ENET0_IOADDR 0xe0000000 328 #define PCI_ENET0_MEMADDR 0xe0000000 329 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 330 #endif 331 332 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 333 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 334 335 #endif /* CONFIG_PCI */ 336 337 338 #ifdef CONFIG_TSEC_ENET 339 340 #ifndef CONFIG_NET_MULTI 341 #define CONFIG_NET_MULTI 1 342 #endif 343 344 #ifndef CONFIG_MII 345 #define CONFIG_MII 1 /* MII PHY management */ 346 #endif 347 #define CONFIG_TSEC1 1 348 #define CONFIG_TSEC1_NAME "TSEC0" 349 #define CONFIG_TSEC2 1 350 #define CONFIG_TSEC2_NAME "TSEC1" 351 #define TSEC1_PHY_ADDR 0 352 #define TSEC2_PHY_ADDR 1 353 #define TSEC1_PHYIDX 0 354 #define TSEC2_PHYIDX 0 355 #define TSEC1_FLAGS TSEC_GIGABIT 356 #define TSEC2_FLAGS TSEC_GIGABIT 357 358 /* Options are: TSEC[0-1] */ 359 #define CONFIG_ETHPRIME "TSEC0" 360 361 #endif /* CONFIG_TSEC_ENET */ 362 363 #ifdef CONFIG_ETHER_ON_FCC /* CPM FCC Ethernet */ 364 365 #undef CONFIG_ETHER_NONE /* define if ether on something else */ 366 #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ 367 368 #if (CONFIG_ETHER_INDEX == 2) 369 /* 370 * - Rx-CLK is CLK13 371 * - Tx-CLK is CLK14 372 * - Select bus for bd/buffers 373 * - Full duplex 374 */ 375 #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) 376 #define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) 377 #define CONFIG_SYS_CPMFCR_RAMTYPE 0 378 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) 379 #define FETH2_RST 0x01 380 #elif (CONFIG_ETHER_INDEX == 3) 381 /* need more definitions here for FE3 */ 382 #define FETH3_RST 0x80 383 #endif /* CONFIG_ETHER_INDEX */ 384 385 #ifndef CONFIG_MII 386 #define CONFIG_MII 1 /* MII PHY management */ 387 #endif 388 389 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 390 391 /* 392 * GPIO pins used for bit-banged MII communications 393 */ 394 #define MDIO_PORT 2 /* Port C */ 395 #define MDIO_ACTIVE (iop->pdir |= 0x00400000) 396 #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) 397 #define MDIO_READ ((iop->pdat & 0x00400000) != 0) 398 399 #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ 400 else iop->pdat &= ~0x00400000 401 402 #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ 403 else iop->pdat &= ~0x00200000 404 405 #define MIIDELAY udelay(1) 406 407 #endif 408 409 410 /* 411 * Environment 412 */ 413 #ifndef CONFIG_SYS_RAMBOOT 414 #define CONFIG_ENV_IS_IN_FLASH 1 415 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 416 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 417 #define CONFIG_ENV_SIZE 0x2000 418 #else 419 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 420 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 421 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 422 #define CONFIG_ENV_SIZE 0x2000 423 #endif 424 425 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 426 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 427 428 /* 429 * BOOTP options 430 */ 431 #define CONFIG_BOOTP_BOOTFILESIZE 432 #define CONFIG_BOOTP_BOOTPATH 433 #define CONFIG_BOOTP_GATEWAY 434 #define CONFIG_BOOTP_HOSTNAME 435 436 437 /* 438 * Command line configuration. 439 */ 440 #include <config_cmd_default.h> 441 442 #define CONFIG_CMD_PING 443 #define CONFIG_CMD_I2C 444 #define CONFIG_CMD_ELF 445 #define CONFIG_CMD_IRQ 446 #define CONFIG_CMD_SETEXPR 447 448 #if defined(CONFIG_PCI) 449 #define CONFIG_CMD_PCI 450 #endif 451 452 #if defined(CONFIG_ETHER_ON_FCC) 453 #define CONFIG_CMD_MII 454 #endif 455 456 #if defined(CONFIG_SYS_RAMBOOT) 457 #undef CONFIG_CMD_ENV 458 #undef CONFIG_CMD_LOADS 459 #endif 460 461 462 #undef CONFIG_WATCHDOG /* watchdog disabled */ 463 464 /* 465 * Miscellaneous configurable options 466 */ 467 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 468 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 469 #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ 470 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 471 472 #if defined(CONFIG_CMD_KGDB) 473 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 474 #else 475 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 476 #endif 477 478 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 479 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 480 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 481 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 482 483 /* 484 * For booting Linux, the board info and command line data 485 * have to be in the first 8 MB of memory, since this is 486 * the maximum mapped by the Linux kernel during initialization. 487 */ 488 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ 489 490 /* 491 * Internal Definitions 492 * 493 * Boot Flags 494 */ 495 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 496 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 497 498 #if defined(CONFIG_CMD_KGDB) 499 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 500 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 501 #endif 502 503 504 /* 505 * Environment Configuration 506 */ 507 508 /* The mac addresses for all ethernet interface */ 509 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) 510 #define CONFIG_HAS_ETH0 511 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 512 #define CONFIG_HAS_ETH1 513 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 514 #define CONFIG_HAS_ETH2 515 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 516 #define CONFIG_HAS_ETH3 517 #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD 518 #endif 519 520 #define CONFIG_IPADDR 192.168.1.253 521 522 #define CONFIG_HOSTNAME unknown 523 #define CONFIG_ROOTPATH /nfsroot 524 #define CONFIG_BOOTFILE your.uImage 525 526 #define CONFIG_SERVERIP 192.168.1.1 527 #define CONFIG_GATEWAYIP 192.168.1.1 528 #define CONFIG_NETMASK 255.255.255.0 529 530 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ 531 532 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 533 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 534 535 #define CONFIG_BAUDRATE 115200 536 537 #define CONFIG_EXTRA_ENV_SETTINGS \ 538 "netdev=eth0\0" \ 539 "consoledev=ttyCPM\0" \ 540 "ramdiskaddr=1000000\0" \ 541 "ramdiskfile=your.ramdisk.u-boot\0" \ 542 "fdtaddr=400000\0" \ 543 "fdtfile=mpc8560ads.dtb\0" 544 545 #define CONFIG_NFSBOOTCOMMAND \ 546 "setenv bootargs root=/dev/nfs rw " \ 547 "nfsroot=$serverip:$rootpath " \ 548 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 549 "console=$consoledev,$baudrate $othbootargs;" \ 550 "tftp $loadaddr $bootfile;" \ 551 "tftp $fdtaddr $fdtfile;" \ 552 "bootm $loadaddr - $fdtaddr" 553 554 #define CONFIG_RAMBOOTCOMMAND \ 555 "setenv bootargs root=/dev/ram rw " \ 556 "console=$consoledev,$baudrate $othbootargs;" \ 557 "tftp $ramdiskaddr $ramdiskfile;" \ 558 "tftp $loadaddr $bootfile;" \ 559 "tftp $fdtaddr $fdtfile;" \ 560 "bootm $loadaddr $ramdiskaddr $fdtaddr" 561 562 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 563 564 #endif /* __CONFIG_H */ 565