1 /* 2 * Copyright 2004, 2011 Freescale Semiconductor. 3 * (C) Copyright 2002,2003 Motorola,Inc. 4 * Xianghua Xiao <X.Xiao@motorola.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * mpc8560ads board configuration file 11 * 12 * Please refer to doc/README.mpc85xx for more info. 13 * 14 * Make sure you change the MAC address and other network params first, 15 * search for CONFIG_SERVERIP, etc. in this file. 16 */ 17 18 #ifndef __CONFIG_H 19 #define __CONFIG_H 20 21 /* High Level Configuration Options */ 22 #define CONFIG_CPM2 1 /* has CPM2 */ 23 24 /* 25 * default CCARBAR is at 0xff700000 26 * assume U-Boot is less than 0.5MB 27 */ 28 29 #define CONFIG_PCI_INDIRECT_BRIDGE 30 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 31 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 32 #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ 33 #define CONFIG_ENV_OVERWRITE 34 #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ 35 36 /* 37 * sysclk for MPC85xx 38 * 39 * Two valid values are: 40 * 33000000 41 * 66000000 42 * 43 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 44 * is likely the desired value here, so that is now the default. 45 * The board, however, can run at 66MHz. In any event, this value 46 * must match the settings of some switches. Details can be found 47 * in the README.mpc85xxads. 48 */ 49 50 #ifndef CONFIG_SYS_CLK_FREQ 51 #define CONFIG_SYS_CLK_FREQ 33000000 52 #endif 53 54 /* 55 * These can be toggled for performance analysis, otherwise use default. 56 */ 57 #define CONFIG_L2_CACHE /* toggle L2 cache */ 58 #define CONFIG_BTB /* toggle branch predition */ 59 60 #define CONFIG_SYS_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ 61 62 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 63 #define CONFIG_SYS_MEMTEST_END 0x00400000 64 65 #define CONFIG_SYS_CCSRBAR 0xe0000000 66 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 67 68 /* DDR Setup */ 69 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 70 #define CONFIG_DDR_SPD 71 #undef CONFIG_FSL_DDR_INTERACTIVE 72 73 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 74 75 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 76 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 77 78 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 79 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 80 81 /* I2C addresses of SPD EEPROMs */ 82 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 83 84 /* These are used when DDR doesn't use SPD. */ 85 #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ 86 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ 87 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 88 #define CONFIG_SYS_DDR_TIMING_1 0x37344321 89 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 90 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 91 #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ 92 #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ 93 94 /* 95 * SDRAM on the Local Bus 96 */ 97 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 98 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 99 100 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 101 #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ 102 103 #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ 104 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 105 #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ 106 #undef CONFIG_SYS_FLASH_CHECKSUM 107 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 108 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 109 110 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 111 112 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 113 #define CONFIG_SYS_RAMBOOT 114 #else 115 #undef CONFIG_SYS_RAMBOOT 116 #endif 117 118 #define CONFIG_FLASH_CFI_DRIVER 119 #define CONFIG_SYS_FLASH_CFI 120 #define CONFIG_SYS_FLASH_EMPTY_INFO 121 122 #undef CONFIG_CLOCKS_IN_MHZ 123 124 /* 125 * Local Bus Definitions 126 */ 127 128 /* 129 * Base Register 2 and Option Register 2 configure SDRAM. 130 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 131 * 132 * For BR2, need: 133 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 134 * port-size = 32-bits = BR2[19:20] = 11 135 * no parity checking = BR2[21:22] = 00 136 * SDRAM for MSEL = BR2[24:26] = 011 137 * Valid = BR[31] = 1 138 * 139 * 0 4 8 12 16 20 24 28 140 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 141 * 142 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 143 * FIXME: the top 17 bits of BR2. 144 */ 145 146 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 147 148 /* 149 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 150 * 151 * For OR2, need: 152 * 64MB mask for AM, OR2[0:7] = 1111 1100 153 * XAM, OR2[17:18] = 11 154 * 9 columns OR2[19-21] = 010 155 * 13 rows OR2[23-25] = 100 156 * EAD set for extra time OR[31] = 1 157 * 158 * 0 4 8 12 16 20 24 28 159 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 160 */ 161 162 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 163 164 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 165 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 166 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 167 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ 168 169 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \ 170 | LSDMR_RFCR5 \ 171 | LSDMR_PRETOACT3 \ 172 | LSDMR_ACTTORW3 \ 173 | LSDMR_BL8 \ 174 | LSDMR_WRC2 \ 175 | LSDMR_CL3 \ 176 | LSDMR_RFEN \ 177 ) 178 179 /* 180 * SDRAM Controller configuration sequence. 181 */ 182 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) 183 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 184 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 185 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) 186 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) 187 188 /* 189 * 32KB, 8-bit wide for ADS config reg 190 */ 191 #define CONFIG_SYS_BR4_PRELIM 0xf8000801 192 #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 193 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) 194 195 #define CONFIG_SYS_INIT_RAM_LOCK 1 196 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 197 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 198 199 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 200 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 201 202 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 203 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 204 205 /* Serial Port */ 206 #define CONFIG_CONS_ON_SCC /* define if console on SCC */ 207 #undef CONFIG_CONS_NONE /* define if console on something else */ 208 #define CONFIG_CONS_INDEX 1 /* which serial channel for console */ 209 210 #define CONFIG_SYS_BAUDRATE_TABLE \ 211 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 212 213 /* 214 * I2C 215 */ 216 #define CONFIG_SYS_I2C 217 #define CONFIG_SYS_I2C_FSL 218 #define CONFIG_SYS_FSL_I2C_SPEED 400000 219 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 220 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 221 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 222 223 /* RapidIO MMU */ 224 #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ 225 #define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */ 226 #define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000 227 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ 228 229 /* 230 * General PCI 231 * Memory space is mapped 1-1, but I/O space must start from 0. 232 */ 233 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 234 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 235 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 236 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 237 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 238 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 239 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 240 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 241 242 #if defined(CONFIG_PCI) 243 #undef CONFIG_EEPRO100 244 #undef CONFIG_TULIP 245 246 #if !defined(CONFIG_PCI_PNP) 247 #define PCI_ENET0_IOADDR 0xe0000000 248 #define PCI_ENET0_MEMADDR 0xe0000000 249 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 250 #endif 251 252 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 253 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 254 255 #endif /* CONFIG_PCI */ 256 257 #ifdef CONFIG_TSEC_ENET 258 259 #ifndef CONFIG_MII 260 #define CONFIG_MII 1 /* MII PHY management */ 261 #endif 262 #define CONFIG_TSEC1 1 263 #define CONFIG_TSEC1_NAME "TSEC0" 264 #define CONFIG_TSEC2 1 265 #define CONFIG_TSEC2_NAME "TSEC1" 266 #define TSEC1_PHY_ADDR 0 267 #define TSEC2_PHY_ADDR 1 268 #define TSEC1_PHYIDX 0 269 #define TSEC2_PHYIDX 0 270 #define TSEC1_FLAGS TSEC_GIGABIT 271 #define TSEC2_FLAGS TSEC_GIGABIT 272 273 /* Options are: TSEC[0-1] */ 274 #define CONFIG_ETHPRIME "TSEC0" 275 276 #endif /* CONFIG_TSEC_ENET */ 277 278 #ifdef CONFIG_ETHER_ON_FCC /* CPM FCC Ethernet */ 279 280 #undef CONFIG_ETHER_NONE /* define if ether on something else */ 281 #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ 282 283 #if (CONFIG_ETHER_INDEX == 2) 284 /* 285 * - Rx-CLK is CLK13 286 * - Tx-CLK is CLK14 287 * - Select bus for bd/buffers 288 * - Full duplex 289 */ 290 #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) 291 #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) 292 #define CONFIG_SYS_CPMFCR_RAMTYPE 0 293 #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) 294 #define FETH2_RST 0x01 295 #elif (CONFIG_ETHER_INDEX == 3) 296 /* need more definitions here for FE3 */ 297 #define FETH3_RST 0x80 298 #endif /* CONFIG_ETHER_INDEX */ 299 300 #ifndef CONFIG_MII 301 #define CONFIG_MII 1 /* MII PHY management */ 302 #endif 303 304 #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ 305 306 /* 307 * GPIO pins used for bit-banged MII communications 308 */ 309 #define MDIO_PORT 2 /* Port C */ 310 #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ 311 (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) 312 #define MDC_DECLARE MDIO_DECLARE 313 314 #define MDIO_ACTIVE (iop->pdir |= 0x00400000) 315 #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) 316 #define MDIO_READ ((iop->pdat & 0x00400000) != 0) 317 318 #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ 319 else iop->pdat &= ~0x00400000 320 321 #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ 322 else iop->pdat &= ~0x00200000 323 324 #define MIIDELAY udelay(1) 325 326 #endif 327 328 /* 329 * Environment 330 */ 331 #ifndef CONFIG_SYS_RAMBOOT 332 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 333 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 334 #define CONFIG_ENV_SIZE 0x2000 335 #else 336 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 337 #define CONFIG_ENV_SIZE 0x2000 338 #endif 339 340 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 341 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 342 343 /* 344 * BOOTP options 345 */ 346 #define CONFIG_BOOTP_BOOTFILESIZE 347 348 #undef CONFIG_WATCHDOG /* watchdog disabled */ 349 350 /* 351 * Miscellaneous configurable options 352 */ 353 #define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ 354 355 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 356 357 /* 358 * For booting Linux, the board info and command line data 359 * have to be in the first 64 MB of memory, since this is 360 * the maximum mapped by the Linux kernel during initialization. 361 */ 362 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 363 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 364 365 #if defined(CONFIG_CMD_KGDB) 366 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 367 #endif 368 369 /* 370 * Environment Configuration 371 */ 372 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) 373 #define CONFIG_HAS_ETH0 374 #define CONFIG_HAS_ETH1 375 #define CONFIG_HAS_ETH2 376 #define CONFIG_HAS_ETH3 377 #endif 378 379 #define CONFIG_IPADDR 192.168.1.253 380 381 #define CONFIG_HOSTNAME unknown 382 #define CONFIG_ROOTPATH "/nfsroot" 383 #define CONFIG_BOOTFILE "your.uImage" 384 385 #define CONFIG_SERVERIP 192.168.1.1 386 #define CONFIG_GATEWAYIP 192.168.1.1 387 #define CONFIG_NETMASK 255.255.255.0 388 389 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ 390 391 #define CONFIG_EXTRA_ENV_SETTINGS \ 392 "netdev=eth0\0" \ 393 "consoledev=ttyCPM\0" \ 394 "ramdiskaddr=1000000\0" \ 395 "ramdiskfile=your.ramdisk.u-boot\0" \ 396 "fdtaddr=400000\0" \ 397 "fdtfile=mpc8560ads.dtb\0" 398 399 #define CONFIG_NFSBOOTCOMMAND \ 400 "setenv bootargs root=/dev/nfs rw " \ 401 "nfsroot=$serverip:$rootpath " \ 402 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 403 "console=$consoledev,$baudrate $othbootargs;" \ 404 "tftp $loadaddr $bootfile;" \ 405 "tftp $fdtaddr $fdtfile;" \ 406 "bootm $loadaddr - $fdtaddr" 407 408 #define CONFIG_RAMBOOTCOMMAND \ 409 "setenv bootargs root=/dev/ram rw " \ 410 "console=$consoledev,$baudrate $othbootargs;" \ 411 "tftp $ramdiskaddr $ramdiskfile;" \ 412 "tftp $loadaddr $bootfile;" \ 413 "tftp $fdtaddr $fdtfile;" \ 414 "bootm $loadaddr $ramdiskaddr $fdtaddr" 415 416 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 417 418 #endif /* __CONFIG_H */ 419