1 /* 2 * Copyright 2004, 2011 Freescale Semiconductor. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8555cds board configuration file 25 * 26 * Please refer to doc/README.mpc85xxcds for more info. 27 * 28 */ 29 #ifndef __CONFIG_H 30 #define __CONFIG_H 31 32 /* High Level Configuration Options */ 33 #define CONFIG_BOOKE 1 /* BOOKE */ 34 #define CONFIG_E500 1 /* BOOKE e500 family */ 35 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ 36 #define CONFIG_CPM2 1 /* has CPM2 */ 37 #define CONFIG_MPC8555 1 /* MPC8555 specific */ 38 #define CONFIG_MPC8555CDS 1 /* MPC8555CDS board specific */ 39 40 #define CONFIG_SYS_TEXT_BASE 0xfff80000 41 42 #define CONFIG_PCI 43 #define CONFIG_PCI_INDIRECT_BRIDGE 44 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 45 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 46 #define CONFIG_ENV_OVERWRITE 47 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 48 49 #define CONFIG_FSL_VIA 50 51 52 #ifndef __ASSEMBLY__ 53 extern unsigned long get_clock_freq(void); 54 #endif 55 #define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ 56 57 /* 58 * These can be toggled for performance analysis, otherwise use default. 59 */ 60 #define CONFIG_L2_CACHE /* toggle L2 cache */ 61 #define CONFIG_BTB /* toggle branch predition */ 62 63 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 64 #define CONFIG_SYS_MEMTEST_END 0x00400000 65 66 #define CONFIG_SYS_CCSRBAR 0xe0000000 67 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 68 69 /* DDR Setup */ 70 #define CONFIG_FSL_DDR1 71 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 72 #define CONFIG_DDR_SPD 73 #undef CONFIG_FSL_DDR_INTERACTIVE 74 75 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 76 77 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 78 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 79 80 #define CONFIG_NUM_DDR_CONTROLLERS 1 81 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 82 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 83 84 /* I2C addresses of SPD EEPROMs */ 85 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 86 87 /* Make sure required options are set */ 88 #ifndef CONFIG_SPD_EEPROM 89 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") 90 #endif 91 92 #undef CONFIG_CLOCKS_IN_MHZ 93 94 /* 95 * Local Bus Definitions 96 */ 97 98 /* 99 * FLASH on the Local Bus 100 * Two banks, 8M each, using the CFI driver. 101 * Boot from BR0/OR0 bank at 0xff00_0000 102 * Alternate BR1/OR1 bank at 0xff80_0000 103 * 104 * BR0, BR1: 105 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 106 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 107 * Port Size = 16 bits = BRx[19:20] = 10 108 * Use GPCM = BRx[24:26] = 000 109 * Valid = BRx[31] = 1 110 * 111 * 0 4 8 12 16 20 24 28 112 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 113 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 114 * 115 * OR0, OR1: 116 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 117 * Reserved ORx[17:18] = 11, confusion here? 118 * CSNT = ORx[20] = 1 119 * ACS = half cycle delay = ORx[21:22] = 11 120 * SCY = 6 = ORx[24:27] = 0110 121 * TRLX = use relaxed timing = ORx[29] = 1 122 * EAD = use external address latch delay = OR[31] = 1 123 * 124 * 0 4 8 12 16 20 24 28 125 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 126 */ 127 128 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ 129 130 #define CONFIG_SYS_BR0_PRELIM 0xff801001 131 #define CONFIG_SYS_BR1_PRELIM 0xff001001 132 133 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 134 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 135 136 #define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} 137 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 138 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 139 #undef CONFIG_SYS_FLASH_CHECKSUM 140 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 141 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 142 143 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 144 145 #define CONFIG_FLASH_CFI_DRIVER 146 #define CONFIG_SYS_FLASH_CFI 147 #define CONFIG_SYS_FLASH_EMPTY_INFO 148 149 150 /* 151 * SDRAM on the Local Bus 152 */ 153 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 154 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 155 156 /* 157 * Base Register 2 and Option Register 2 configure SDRAM. 158 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 159 * 160 * For BR2, need: 161 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 162 * port-size = 32-bits = BR2[19:20] = 11 163 * no parity checking = BR2[21:22] = 00 164 * SDRAM for MSEL = BR2[24:26] = 011 165 * Valid = BR[31] = 1 166 * 167 * 0 4 8 12 16 20 24 28 168 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 169 * 170 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 171 * FIXME: the top 17 bits of BR2. 172 */ 173 174 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 175 176 /* 177 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 178 * 179 * For OR2, need: 180 * 64MB mask for AM, OR2[0:7] = 1111 1100 181 * XAM, OR2[17:18] = 11 182 * 9 columns OR2[19-21] = 010 183 * 13 rows OR2[23-25] = 100 184 * EAD set for extra time OR[31] = 1 185 * 186 * 0 4 8 12 16 20 24 28 187 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 188 */ 189 190 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 191 192 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 193 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 194 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 195 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 196 197 /* 198 * Common settings for all Local Bus SDRAM commands. 199 * At run time, either BSMA1516 (for CPU 1.1) 200 * or BSMA1617 (for CPU 1.0) (old) 201 * is OR'ed in too. 202 */ 203 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 204 | LSDMR_PRETOACT7 \ 205 | LSDMR_ACTTORW7 \ 206 | LSDMR_BL8 \ 207 | LSDMR_WRC4 \ 208 | LSDMR_CL3 \ 209 | LSDMR_RFEN \ 210 ) 211 212 /* 213 * The CADMUS registers are connected to CS3 on CDS. 214 * The new memory map places CADMUS at 0xf8000000. 215 * 216 * For BR3, need: 217 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 218 * port-size = 8-bits = BR[19:20] = 01 219 * no parity checking = BR[21:22] = 00 220 * GPMC for MSEL = BR[24:26] = 000 221 * Valid = BR[31] = 1 222 * 223 * 0 4 8 12 16 20 24 28 224 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 225 * 226 * For OR3, need: 227 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 228 * disable buffer ctrl OR[19] = 0 229 * CSNT OR[20] = 1 230 * ACS OR[21:22] = 11 231 * XACS OR[23] = 1 232 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 233 * SETA OR[28] = 0 234 * TRLX OR[29] = 1 235 * EHTR OR[30] = 1 236 * EAD extra time OR[31] = 1 237 * 238 * 0 4 8 12 16 20 24 28 239 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 240 */ 241 242 #define CONFIG_FSL_CADMUS 243 244 #define CADMUS_BASE_ADDR 0xf8000000 245 #define CONFIG_SYS_BR3_PRELIM 0xf8000801 246 #define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 247 248 #define CONFIG_SYS_INIT_RAM_LOCK 1 249 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 250 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 251 252 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 253 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 254 255 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 256 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 257 258 /* Serial Port */ 259 #define CONFIG_CONS_INDEX 2 260 #define CONFIG_SYS_NS16550 261 #define CONFIG_SYS_NS16550_SERIAL 262 #define CONFIG_SYS_NS16550_REG_SIZE 1 263 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 264 265 #define CONFIG_SYS_BAUDRATE_TABLE \ 266 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 267 268 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 269 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 270 271 /* Use the HUSH parser */ 272 #define CONFIG_SYS_HUSH_PARSER 273 #ifdef CONFIG_SYS_HUSH_PARSER 274 #endif 275 276 /* pass open firmware flat tree */ 277 #define CONFIG_OF_LIBFDT 1 278 #define CONFIG_OF_BOARD_SETUP 1 279 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 280 281 /* 282 * I2C 283 */ 284 #define CONFIG_SYS_I2C 285 #define CONFIG_SYS_I2C_FSL 286 #define CONFIG_SYS_FSL_I2C_SPEED 400000 287 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 288 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 289 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 290 291 /* EEPROM */ 292 #define CONFIG_ID_EEPROM 293 #define CONFIG_SYS_I2C_EEPROM_CCID 294 #define CONFIG_SYS_ID_EEPROM 295 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 296 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 297 298 /* 299 * General PCI 300 * Addresses are mapped 1-1. 301 */ 302 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 303 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 304 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 305 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 306 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 307 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 308 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 309 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 310 311 #define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 312 #define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 313 #define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 314 #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ 315 #define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 316 #define CONFIG_SYS_PCI2_IO_BUS 0x00000000 317 #define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 318 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ 319 320 #ifdef CONFIG_LEGACY 321 #define BRIDGE_ID 17 322 #define VIA_ID 2 323 #else 324 #define BRIDGE_ID 28 325 #define VIA_ID 4 326 #endif 327 328 #if defined(CONFIG_PCI) 329 330 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 331 #define CONFIG_MPC85XX_PCI2 332 333 #undef CONFIG_EEPRO100 334 #undef CONFIG_TULIP 335 336 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 337 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 338 339 #endif /* CONFIG_PCI */ 340 341 342 #if defined(CONFIG_TSEC_ENET) 343 344 #define CONFIG_MII 1 /* MII PHY management */ 345 #define CONFIG_TSEC1 1 346 #define CONFIG_TSEC1_NAME "TSEC0" 347 #define CONFIG_TSEC2 1 348 #define CONFIG_TSEC2_NAME "TSEC1" 349 #define TSEC1_PHY_ADDR 0 350 #define TSEC2_PHY_ADDR 1 351 #define TSEC1_PHYIDX 0 352 #define TSEC2_PHYIDX 0 353 #define TSEC1_FLAGS TSEC_GIGABIT 354 #define TSEC2_FLAGS TSEC_GIGABIT 355 356 /* Options are: TSEC[0-1] */ 357 #define CONFIG_ETHPRIME "TSEC0" 358 359 #endif /* CONFIG_TSEC_ENET */ 360 361 /* 362 * Environment 363 */ 364 #define CONFIG_ENV_IS_IN_FLASH 1 365 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 366 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 367 #define CONFIG_ENV_SIZE 0x2000 368 369 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 370 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 371 372 /* 373 * BOOTP options 374 */ 375 #define CONFIG_BOOTP_BOOTFILESIZE 376 #define CONFIG_BOOTP_BOOTPATH 377 #define CONFIG_BOOTP_GATEWAY 378 #define CONFIG_BOOTP_HOSTNAME 379 380 381 /* 382 * Command line configuration. 383 */ 384 #include <config_cmd_default.h> 385 386 #define CONFIG_CMD_PING 387 #define CONFIG_CMD_I2C 388 #define CONFIG_CMD_MII 389 #define CONFIG_CMD_ELF 390 #define CONFIG_CMD_IRQ 391 #define CONFIG_CMD_SETEXPR 392 #define CONFIG_CMD_REGINFO 393 394 #if defined(CONFIG_PCI) 395 #define CONFIG_CMD_PCI 396 #endif 397 398 399 #undef CONFIG_WATCHDOG /* watchdog disabled */ 400 401 /* 402 * Miscellaneous configurable options 403 */ 404 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 405 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 406 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 407 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 408 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 409 #if defined(CONFIG_CMD_KGDB) 410 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 411 #else 412 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 413 #endif 414 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 415 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 416 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 417 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 418 419 /* 420 * For booting Linux, the board info and command line data 421 * have to be in the first 64 MB of memory, since this is 422 * the maximum mapped by the Linux kernel during initialization. 423 */ 424 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 425 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 426 427 #if defined(CONFIG_CMD_KGDB) 428 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 429 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 430 #endif 431 432 /* 433 * Environment Configuration 434 */ 435 436 /* The mac addresses for all ethernet interface */ 437 #if defined(CONFIG_TSEC_ENET) 438 #define CONFIG_HAS_ETH0 439 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 440 #define CONFIG_HAS_ETH1 441 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 442 #define CONFIG_HAS_ETH2 443 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 444 #endif 445 446 #define CONFIG_IPADDR 192.168.1.253 447 448 #define CONFIG_HOSTNAME unknown 449 #define CONFIG_ROOTPATH "/nfsroot" 450 #define CONFIG_BOOTFILE "your.uImage" 451 452 #define CONFIG_SERVERIP 192.168.1.1 453 #define CONFIG_GATEWAYIP 192.168.1.1 454 #define CONFIG_NETMASK 255.255.255.0 455 456 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 457 458 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 459 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 460 461 #define CONFIG_BAUDRATE 115200 462 463 #define CONFIG_EXTRA_ENV_SETTINGS \ 464 "netdev=eth0\0" \ 465 "consoledev=ttyS1\0" \ 466 "ramdiskaddr=600000\0" \ 467 "ramdiskfile=your.ramdisk.u-boot\0" \ 468 "fdtaddr=400000\0" \ 469 "fdtfile=your.fdt.dtb\0" 470 471 #define CONFIG_NFSBOOTCOMMAND \ 472 "setenv bootargs root=/dev/nfs rw " \ 473 "nfsroot=$serverip:$rootpath " \ 474 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 475 "console=$consoledev,$baudrate $othbootargs;" \ 476 "tftp $loadaddr $bootfile;" \ 477 "tftp $fdtaddr $fdtfile;" \ 478 "bootm $loadaddr - $fdtaddr" 479 480 #define CONFIG_RAMBOOTCOMMAND \ 481 "setenv bootargs root=/dev/ram rw " \ 482 "console=$consoledev,$baudrate $othbootargs;" \ 483 "tftp $ramdiskaddr $ramdiskfile;" \ 484 "tftp $loadaddr $bootfile;" \ 485 "bootm $loadaddr $ramdiskaddr" 486 487 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 488 489 #endif /* __CONFIG_H */ 490