1 /* 2 * Copyright 2004, 2007, 2010-2011 Freescale Semiconductor. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8548cds board configuration file 9 * 10 * Please refer to doc/README.mpc85xxcds for more info. 11 * 12 */ 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #define CONFIG_SYS_GENERIC_BOARD 17 #define CONFIG_DISPLAY_BOARDINFO 18 19 #ifdef CONFIG_36BIT 20 #define CONFIG_PHYS_64BIT 21 #endif 22 23 /* High Level Configuration Options */ 24 #define CONFIG_BOOKE 1 /* BOOKE */ 25 #define CONFIG_E500 1 /* BOOKE e500 family */ 26 #define CONFIG_MPC8548 1 /* MPC8548 specific */ 27 #define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */ 28 29 #ifndef CONFIG_SYS_TEXT_BASE 30 #define CONFIG_SYS_TEXT_BASE 0xfff80000 31 #endif 32 33 #define CONFIG_SYS_SRIO 34 #define CONFIG_SRIO1 /* SRIO port 1 */ 35 36 #define CONFIG_PCI /* enable any pci type devices */ 37 #define CONFIG_PCI1 /* PCI controller 1 */ 38 #define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ 39 #undef CONFIG_PCI2 40 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 41 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 42 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 43 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 44 45 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 46 #define CONFIG_ENV_OVERWRITE 47 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 48 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 49 50 #define CONFIG_FSL_VIA 51 52 #ifndef __ASSEMBLY__ 53 extern unsigned long get_clock_freq(void); 54 #endif 55 #define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ 56 57 /* 58 * These can be toggled for performance analysis, otherwise use default. 59 */ 60 #define CONFIG_L2_CACHE /* toggle L2 cache */ 61 #define CONFIG_BTB /* toggle branch predition */ 62 63 /* 64 * Only possible on E500 Version 2 or newer cores. 65 */ 66 #define CONFIG_ENABLE_36BIT_PHYS 1 67 68 #ifdef CONFIG_PHYS_64BIT 69 #define CONFIG_ADDR_MAP 70 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 71 #endif 72 73 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 74 #define CONFIG_SYS_MEMTEST_END 0x00400000 75 76 #define CONFIG_SYS_CCSRBAR 0xe0000000 77 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 78 79 /* DDR Setup */ 80 #define CONFIG_SYS_FSL_DDR2 81 #undef CONFIG_FSL_DDR_INTERACTIVE 82 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 83 #define CONFIG_DDR_SPD 84 85 #define CONFIG_DDR_ECC 86 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 87 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 88 89 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 90 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 91 92 #define CONFIG_NUM_DDR_CONTROLLERS 1 93 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 94 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 95 96 /* I2C addresses of SPD EEPROMs */ 97 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 98 99 /* Make sure required options are set */ 100 #ifndef CONFIG_SPD_EEPROM 101 #error ("CONFIG_SPD_EEPROM is required") 102 #endif 103 104 #undef CONFIG_CLOCKS_IN_MHZ 105 /* 106 * Physical Address Map 107 * 108 * 32bit: 109 * 0x0000_0000 0x7fff_ffff DDR 2G cacheable 110 * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M cacheable 111 * 0xa000_0000 0xbfff_ffff PCIe MEM 512M cacheable 112 * 0xc000_0000 0xdfff_ffff RapidIO 512M cacheable 113 * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable 114 * 0xe200_0000 0xe20f_ffff PCI1 IO 1M non-cacheable 115 * 0xe300_0000 0xe30f_ffff PCIe IO 1M non-cacheable 116 * 0xf000_0000 0xf3ff_ffff SDRAM 64M cacheable 117 * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS 1M non-cacheable 118 * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable 119 * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable 120 * 121 * 36bit: 122 * 0x00000_0000 0x07fff_ffff DDR 2G cacheable 123 * 0xc0000_0000 0xc1fff_ffff PCI1 MEM 512M cacheable 124 * 0xc2000_0000 0xc3fff_ffff PCIe MEM 512M cacheable 125 * 0xc4000_0000 0xc5fff_ffff RapidIO 512M cacheable 126 * 0xfe000_0000 0xfe00f_ffff CCSR 1M non-cacheable 127 * 0xfe200_0000 0xfe20f_ffff PCI1 IO 1M non-cacheable 128 * 0xfe300_0000 0xfe30f_ffff PCIe IO 1M non-cacheable 129 * 0xff000_0000 0xff3ff_ffff SDRAM 64M cacheable 130 * 0xff800_0000 0xff80f_ffff NVRAM/CADMUS 1M non-cacheable 131 * 0xfff00_0000 0xfff7f_ffff FLASH (2nd bank) 8M non-cacheable 132 * 0xfff80_0000 0xfffff_ffff FLASH (boot bank) 8M non-cacheable 133 * 134 */ 135 136 137 /* 138 * Local Bus Definitions 139 */ 140 141 /* 142 * FLASH on the Local Bus 143 * Two banks, 8M each, using the CFI driver. 144 * Boot from BR0/OR0 bank at 0xff00_0000 145 * Alternate BR1/OR1 bank at 0xff80_0000 146 * 147 * BR0, BR1: 148 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 149 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 150 * Port Size = 16 bits = BRx[19:20] = 10 151 * Use GPCM = BRx[24:26] = 000 152 * Valid = BRx[31] = 1 153 * 154 * 0 4 8 12 16 20 24 28 155 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 156 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 157 * 158 * OR0, OR1: 159 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 160 * Reserved ORx[17:18] = 11, confusion here? 161 * CSNT = ORx[20] = 1 162 * ACS = half cycle delay = ORx[21:22] = 11 163 * SCY = 6 = ORx[24:27] = 0110 164 * TRLX = use relaxed timing = ORx[29] = 1 165 * EAD = use external address latch delay = OR[31] = 1 166 * 167 * 0 4 8 12 16 20 24 28 168 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 169 */ 170 171 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 172 #ifdef CONFIG_PHYS_64BIT 173 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfff000000ull 174 #else 175 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 176 #endif 177 178 #define CONFIG_SYS_BR0_PRELIM \ 179 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x800000) | BR_PS_16 | BR_V) 180 #define CONFIG_SYS_BR1_PRELIM \ 181 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) 182 183 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 184 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 185 186 #define CONFIG_SYS_FLASH_BANKS_LIST \ 187 {CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS} 188 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 189 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 190 #undef CONFIG_SYS_FLASH_CHECKSUM 191 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 192 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 193 194 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 195 196 #define CONFIG_FLASH_CFI_DRIVER 197 #define CONFIG_SYS_FLASH_CFI 198 #define CONFIG_SYS_FLASH_EMPTY_INFO 199 200 #define CONFIG_HWCONFIG /* enable hwconfig */ 201 202 /* 203 * SDRAM on the Local Bus 204 */ 205 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 206 #ifdef CONFIG_PHYS_64BIT 207 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS 0xff0000000ull 208 #else 209 #define CONFIG_SYS_LBC_SDRAM_BASE_PHYS CONFIG_SYS_LBC_SDRAM_BASE 210 #endif 211 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 212 213 /* 214 * Base Register 2 and Option Register 2 configure SDRAM. 215 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 216 * 217 * For BR2, need: 218 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 219 * port-size = 32-bits = BR2[19:20] = 11 220 * no parity checking = BR2[21:22] = 00 221 * SDRAM for MSEL = BR2[24:26] = 011 222 * Valid = BR[31] = 1 223 * 224 * 0 4 8 12 16 20 24 28 225 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 226 * 227 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 228 * FIXME: the top 17 bits of BR2. 229 */ 230 231 #define CONFIG_SYS_BR2_PRELIM \ 232 (BR_PHYS_ADDR(CONFIG_SYS_LBC_SDRAM_BASE_PHYS) \ 233 | BR_PS_32 | (3<<BR_MSEL_SHIFT) | BR_V) 234 235 /* 236 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 237 * 238 * For OR2, need: 239 * 64MB mask for AM, OR2[0:7] = 1111 1100 240 * XAM, OR2[17:18] = 11 241 * 9 columns OR2[19-21] = 010 242 * 13 rows OR2[23-25] = 100 243 * EAD set for extra time OR[31] = 1 244 * 245 * 0 4 8 12 16 20 24 28 246 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 247 */ 248 249 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 250 251 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 252 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 253 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 254 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 255 256 /* 257 * Common settings for all Local Bus SDRAM commands. 258 * At run time, either BSMA1516 (for CPU 1.1) 259 * or BSMA1617 (for CPU 1.0) (old) 260 * is OR'ed in too. 261 */ 262 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 263 | LSDMR_PRETOACT7 \ 264 | LSDMR_ACTTORW7 \ 265 | LSDMR_BL8 \ 266 | LSDMR_WRC4 \ 267 | LSDMR_CL3 \ 268 | LSDMR_RFEN \ 269 ) 270 271 /* 272 * The CADMUS registers are connected to CS3 on CDS. 273 * The new memory map places CADMUS at 0xf8000000. 274 * 275 * For BR3, need: 276 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 277 * port-size = 8-bits = BR[19:20] = 01 278 * no parity checking = BR[21:22] = 00 279 * GPMC for MSEL = BR[24:26] = 000 280 * Valid = BR[31] = 1 281 * 282 * 0 4 8 12 16 20 24 28 283 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 284 * 285 * For OR3, need: 286 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 287 * disable buffer ctrl OR[19] = 0 288 * CSNT OR[20] = 1 289 * ACS OR[21:22] = 11 290 * XACS OR[23] = 1 291 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 292 * SETA OR[28] = 0 293 * TRLX OR[29] = 1 294 * EHTR OR[30] = 1 295 * EAD extra time OR[31] = 1 296 * 297 * 0 4 8 12 16 20 24 28 298 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 299 */ 300 301 #define CONFIG_FSL_CADMUS 302 303 #define CADMUS_BASE_ADDR 0xf8000000 304 #ifdef CONFIG_PHYS_64BIT 305 #define CADMUS_BASE_ADDR_PHYS 0xff8000000ull 306 #else 307 #define CADMUS_BASE_ADDR_PHYS CADMUS_BASE_ADDR 308 #endif 309 #define CONFIG_SYS_BR3_PRELIM \ 310 (BR_PHYS_ADDR(CADMUS_BASE_ADDR_PHYS) | BR_PS_8 | BR_V) 311 #define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 312 313 #define CONFIG_SYS_INIT_RAM_LOCK 1 314 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 315 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 316 317 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 318 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 319 320 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 321 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 322 323 /* Serial Port */ 324 #define CONFIG_CONS_INDEX 2 325 #define CONFIG_SYS_NS16550 326 #define CONFIG_SYS_NS16550_SERIAL 327 #define CONFIG_SYS_NS16550_REG_SIZE 1 328 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 329 330 #define CONFIG_SYS_BAUDRATE_TABLE \ 331 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 332 333 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 334 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 335 336 /* Use the HUSH parser */ 337 #define CONFIG_SYS_HUSH_PARSER 338 339 /* pass open firmware flat tree */ 340 #define CONFIG_OF_LIBFDT 1 341 #define CONFIG_OF_BOARD_SETUP 1 342 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 343 344 /* 345 * I2C 346 */ 347 #define CONFIG_SYS_I2C 348 #define CONFIG_SYS_I2C_FSL 349 #define CONFIG_SYS_FSL_I2C_SPEED 400000 350 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 351 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 352 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 353 354 /* EEPROM */ 355 #define CONFIG_ID_EEPROM 356 #define CONFIG_SYS_I2C_EEPROM_CCID 357 #define CONFIG_SYS_ID_EEPROM 358 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 359 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 360 361 /* 362 * General PCI 363 * Memory space is mapped 1-1, but I/O space must start from 0. 364 */ 365 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 366 #ifdef CONFIG_PHYS_64BIT 367 #define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000 368 #define CONFIG_SYS_PCI1_MEM_PHYS 0xc00000000ull 369 #else 370 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 371 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 372 #endif 373 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 374 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 375 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 376 #ifdef CONFIG_PHYS_64BIT 377 #define CONFIG_SYS_PCI1_IO_PHYS 0xfe2000000ull 378 #else 379 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 380 #endif 381 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 382 383 #ifdef CONFIG_PCIE1 384 #define CONFIG_SYS_PCIE1_NAME "Slot" 385 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 386 #ifdef CONFIG_PHYS_64BIT 387 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 388 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc20000000ull 389 #else 390 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 391 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 392 #endif 393 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 394 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe3000000 395 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 396 #ifdef CONFIG_PHYS_64BIT 397 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfe3000000ull 398 #else 399 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe3000000 400 #endif 401 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */ 402 #endif 403 404 /* 405 * RapidIO MMU 406 */ 407 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xc0000000 408 #ifdef CONFIG_PHYS_64BIT 409 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc40000000ull 410 #else 411 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc0000000 412 #endif 413 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ 414 415 #ifdef CONFIG_LEGACY 416 #define BRIDGE_ID 17 417 #define VIA_ID 2 418 #else 419 #define BRIDGE_ID 28 420 #define VIA_ID 4 421 #endif 422 423 #if defined(CONFIG_PCI) 424 425 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 426 427 #undef CONFIG_EEPRO100 428 #undef CONFIG_TULIP 429 430 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 431 432 #endif /* CONFIG_PCI */ 433 434 435 #if defined(CONFIG_TSEC_ENET) 436 437 #define CONFIG_MII 1 /* MII PHY management */ 438 #define CONFIG_TSEC1 1 439 #define CONFIG_TSEC1_NAME "eTSEC0" 440 #define CONFIG_TSEC2 1 441 #define CONFIG_TSEC2_NAME "eTSEC1" 442 #define CONFIG_TSEC3 1 443 #define CONFIG_TSEC3_NAME "eTSEC2" 444 #define CONFIG_TSEC4 445 #define CONFIG_TSEC4_NAME "eTSEC3" 446 #undef CONFIG_MPC85XX_FEC 447 448 #define CONFIG_PHY_MARVELL 449 450 #define TSEC1_PHY_ADDR 0 451 #define TSEC2_PHY_ADDR 1 452 #define TSEC3_PHY_ADDR 2 453 #define TSEC4_PHY_ADDR 3 454 455 #define TSEC1_PHYIDX 0 456 #define TSEC2_PHYIDX 0 457 #define TSEC3_PHYIDX 0 458 #define TSEC4_PHYIDX 0 459 #define TSEC1_FLAGS TSEC_GIGABIT 460 #define TSEC2_FLAGS TSEC_GIGABIT 461 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 462 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 463 464 /* Options are: eTSEC[0-3] */ 465 #define CONFIG_ETHPRIME "eTSEC0" 466 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 467 #endif /* CONFIG_TSEC_ENET */ 468 469 /* 470 * Environment 471 */ 472 #define CONFIG_ENV_IS_IN_FLASH 1 473 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 474 #define CONFIG_ENV_ADDR 0xfff80000 475 #else 476 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 477 #endif 478 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K for env */ 479 #define CONFIG_ENV_SIZE 0x2000 480 481 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 482 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 483 484 /* 485 * BOOTP options 486 */ 487 #define CONFIG_BOOTP_BOOTFILESIZE 488 #define CONFIG_BOOTP_BOOTPATH 489 #define CONFIG_BOOTP_GATEWAY 490 #define CONFIG_BOOTP_HOSTNAME 491 492 493 /* 494 * Command line configuration. 495 */ 496 #define CONFIG_CMD_PING 497 #define CONFIG_CMD_I2C 498 #define CONFIG_CMD_MII 499 #define CONFIG_CMD_IRQ 500 #define CONFIG_CMD_REGINFO 501 502 #if defined(CONFIG_PCI) 503 #define CONFIG_CMD_PCI 504 #endif 505 506 507 #undef CONFIG_WATCHDOG /* watchdog disabled */ 508 509 /* 510 * Miscellaneous configurable options 511 */ 512 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 513 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 514 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 515 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 516 #if defined(CONFIG_CMD_KGDB) 517 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 518 #else 519 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 520 #endif 521 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 522 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 523 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 524 525 /* 526 * For booting Linux, the board info and command line data 527 * have to be in the first 64 MB of memory, since this is 528 * the maximum mapped by the Linux kernel during initialization. 529 */ 530 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 531 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 532 533 #if defined(CONFIG_CMD_KGDB) 534 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 535 #endif 536 537 /* 538 * Environment Configuration 539 */ 540 #if defined(CONFIG_TSEC_ENET) 541 #define CONFIG_HAS_ETH0 542 #define CONFIG_HAS_ETH1 543 #define CONFIG_HAS_ETH2 544 #define CONFIG_HAS_ETH3 545 #endif 546 547 #define CONFIG_IPADDR 192.168.1.253 548 549 #define CONFIG_HOSTNAME unknown 550 #define CONFIG_ROOTPATH "/nfsroot" 551 #define CONFIG_BOOTFILE "8548cds/uImage.uboot" 552 #define CONFIG_UBOOTPATH 8548cds/u-boot.bin /* TFTP server */ 553 554 #define CONFIG_SERVERIP 192.168.1.1 555 #define CONFIG_GATEWAYIP 192.168.1.1 556 #define CONFIG_NETMASK 255.255.255.0 557 558 #define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ 559 560 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 561 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 562 563 #define CONFIG_BAUDRATE 115200 564 565 #define CONFIG_EXTRA_ENV_SETTINGS \ 566 "hwconfig=fsl_ddr:ecc=off\0" \ 567 "netdev=eth0\0" \ 568 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 569 "tftpflash=tftpboot $loadaddr $uboot; " \ 570 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 571 " +$filesize; " \ 572 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 573 " +$filesize; " \ 574 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 575 " $filesize; " \ 576 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 577 " +$filesize; " \ 578 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 579 " $filesize\0" \ 580 "consoledev=ttyS1\0" \ 581 "ramdiskaddr=2000000\0" \ 582 "ramdiskfile=ramdisk.uboot\0" \ 583 "fdtaddr=c00000\0" \ 584 "fdtfile=mpc8548cds.dtb\0" 585 586 #define CONFIG_NFSBOOTCOMMAND \ 587 "setenv bootargs root=/dev/nfs rw " \ 588 "nfsroot=$serverip:$rootpath " \ 589 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 590 "console=$consoledev,$baudrate $othbootargs;" \ 591 "tftp $loadaddr $bootfile;" \ 592 "tftp $fdtaddr $fdtfile;" \ 593 "bootm $loadaddr - $fdtaddr" 594 595 596 #define CONFIG_RAMBOOTCOMMAND \ 597 "setenv bootargs root=/dev/ram rw " \ 598 "console=$consoledev,$baudrate $othbootargs;" \ 599 "tftp $ramdiskaddr $ramdiskfile;" \ 600 "tftp $loadaddr $bootfile;" \ 601 "tftp $fdtaddr $fdtfile;" \ 602 "bootm $loadaddr $ramdiskaddr $fdtaddr" 603 604 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 605 606 #endif /* __CONFIG_H */ 607