1 /* 2 * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8544ds board configuration file 9 * 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #define CONFIG_DISPLAY_BOARDINFO 15 16 /* High Level Configuration Options */ 17 #define CONFIG_BOOKE 1 /* BOOKE */ 18 #define CONFIG_E500 1 /* BOOKE e500 family */ 19 #define CONFIG_MPC8544 1 20 #define CONFIG_MPC8544DS 1 21 22 #ifndef CONFIG_SYS_TEXT_BASE 23 #define CONFIG_SYS_TEXT_BASE 0xfff80000 24 #endif 25 26 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 27 #define CONFIG_PCI1 1 /* PCI controller 1 */ 28 #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ 29 #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ 30 #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ 31 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 32 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 33 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 34 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 35 36 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 37 38 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 39 #define CONFIG_ENV_OVERWRITE 40 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ 41 42 #ifndef __ASSEMBLY__ 43 extern unsigned long get_board_sys_clk(unsigned long dummy); 44 #endif 45 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 46 47 /* 48 * These can be toggled for performance analysis, otherwise use default. 49 */ 50 #define CONFIG_L2_CACHE /* toggle L2 cache */ 51 #define CONFIG_BTB /* toggle branch predition */ 52 53 /* 54 * Only possible on E500 Version 2 or newer cores. 55 */ 56 #define CONFIG_ENABLE_36BIT_PHYS 1 57 58 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 59 #define CONFIG_SYS_MEMTEST_END 0x00400000 60 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 61 62 #define CONFIG_SYS_CCSRBAR 0xe0000000 63 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 64 65 /* DDR Setup */ 66 #define CONFIG_SYS_FSL_DDR2 67 #undef CONFIG_FSL_DDR_INTERACTIVE 68 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 69 #define CONFIG_DDR_SPD 70 71 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 72 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 73 74 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 75 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 76 #define CONFIG_VERY_BIG_RAM 77 78 #define CONFIG_NUM_DDR_CONTROLLERS 1 79 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 80 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 81 82 /* I2C addresses of SPD EEPROMs */ 83 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ 84 85 /* Make sure required options are set */ 86 #ifndef CONFIG_SPD_EEPROM 87 #error ("CONFIG_SPD_EEPROM is required") 88 #endif 89 90 #undef CONFIG_CLOCKS_IN_MHZ 91 92 /* 93 * Memory map 94 * 95 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 96 * 97 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable 98 * 99 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable 100 * 101 * 0xe000_0000 0xe00f_ffff CCSR 1M non-cacheable 102 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable 103 * 104 * Localbus cacheable 105 * 106 * 0xf000_0000 0xf3ff_ffff SDRAM 64M Cacheable 107 * 0xf401_0000 0xf401_3fff L1 for stack 4K Cacheable TLB0 108 * 109 * Localbus non-cacheable 110 * 111 * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M non-cacheable 112 * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M non-cacheable 113 * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M non-cacheable 114 * 115 */ 116 117 /* 118 * Local Bus Definitions 119 */ 120 #define CONFIG_SYS_BOOT_BLOCK 0xfc000000 /* boot TLB */ 121 122 #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ 123 124 #define CONFIG_SYS_BR0_PRELIM 0xff801001 125 #define CONFIG_SYS_BR1_PRELIM 0xfe801001 126 127 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 128 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 129 130 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} 131 132 #define CONFIG_SYS_FLASH_QUIET_TEST 133 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 134 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 135 #undef CONFIG_SYS_FLASH_CHECKSUM 136 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 137 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 138 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 139 140 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 141 142 #define CONFIG_FLASH_CFI_DRIVER 143 #define CONFIG_SYS_FLASH_CFI 144 #define CONFIG_SYS_FLASH_EMPTY_INFO 145 146 #define CONFIG_SYS_LBC_NONCACHE_BASE 0xf8000000 147 148 #define CONFIG_SYS_BR2_PRELIM 0xf8201001 /* port size 16bit */ 149 #define CONFIG_SYS_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/ 150 151 #define CONFIG_SYS_BR3_PRELIM 0xf8100801 /* port size 8bit */ 152 #define CONFIG_SYS_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/ 153 154 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 155 #define PIXIS_BASE 0xf8100000 /* PIXIS registers */ 156 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 157 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 158 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 159 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 160 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch 161 * register */ 162 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 163 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 164 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 165 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 166 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 167 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 168 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 169 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 170 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 171 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 172 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 173 #define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */ 174 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 175 #define PIXIS_VSPEED2_TSEC1SER 0x2 176 #define PIXIS_VSPEED2_TSEC3SER 0x1 177 #define PIXIS_VCFGEN1_TSEC1SER 0x20 178 #define PIXIS_VCFGEN1_TSEC3SER 0x40 179 #define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER) 180 #define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER) 181 182 183 #define CONFIG_SYS_INIT_RAM_LOCK 1 184 #define CONFIG_SYS_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ 185 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ 186 187 188 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 189 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 190 191 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 192 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 193 194 /* Serial Port - controlled on board with jumper J8 195 * open - index 2 196 * shorted - index 1 197 */ 198 #define CONFIG_CONS_INDEX 1 199 #define CONFIG_SYS_NS16550 200 #define CONFIG_SYS_NS16550_SERIAL 201 #define CONFIG_SYS_NS16550_REG_SIZE 1 202 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 203 204 #define CONFIG_SYS_BAUDRATE_TABLE \ 205 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 206 207 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 208 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 209 210 /* Use the HUSH parser */ 211 #define CONFIG_SYS_HUSH_PARSER 212 213 /* pass open firmware flat tree */ 214 #define CONFIG_OF_LIBFDT 1 215 #define CONFIG_OF_BOARD_SETUP 1 216 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 217 218 /* I2C */ 219 #define CONFIG_SYS_I2C 220 #define CONFIG_SYS_I2C_FSL 221 #define CONFIG_SYS_FSL_I2C_SPEED 400000 222 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 223 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 224 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 225 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 226 227 /* 228 * General PCI 229 * Memory space is mapped 1-1, but I/O space must start from 0. 230 */ 231 #define CONFIG_SYS_PCIE_VIRT 0x80000000 /* 1G PCIE TLB */ 232 #define CONFIG_SYS_PCIE_PHYS 0x80000000 /* 1G PCIE TLB */ 233 #define CONFIG_SYS_PCI_VIRT 0xc0000000 /* 512M PCI TLB */ 234 #define CONFIG_SYS_PCI_PHYS 0xc0000000 /* 512M PCI TLB */ 235 236 #define CONFIG_SYS_PCI1_MEM_VIRT 0xc0000000 237 #define CONFIG_SYS_PCI1_MEM_BUS 0xc0000000 238 #define CONFIG_SYS_PCI1_MEM_PHYS 0xc0000000 239 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 240 #define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000 241 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 242 #define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000 243 #define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ 244 245 /* controller 2, Slot 1, tgtid 1, Base address 9000 */ 246 #define CONFIG_SYS_PCIE2_NAME "Slot 1" 247 #define CONFIG_SYS_PCIE2_MEM_VIRT 0x80000000 248 #define CONFIG_SYS_PCIE2_MEM_BUS 0x80000000 249 #define CONFIG_SYS_PCIE2_MEM_PHYS 0x80000000 250 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 251 #define CONFIG_SYS_PCIE2_IO_VIRT 0xe1010000 252 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 253 #define CONFIG_SYS_PCIE2_IO_PHYS 0xe1010000 254 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 255 256 /* controller 1, Slot 2,tgtid 2, Base address a000 */ 257 #define CONFIG_SYS_PCIE1_NAME "Slot 2" 258 #define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 259 #define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 260 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 261 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */ 262 #define CONFIG_SYS_PCIE1_IO_VIRT 0xe1020000 263 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 264 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe1020000 265 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 266 267 /* controller 3, direct to uli, tgtid 3, Base address b000 */ 268 #define CONFIG_SYS_PCIE3_NAME "ULI" 269 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xb0000000 270 #define CONFIG_SYS_PCIE3_MEM_BUS 0xb0000000 271 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xb0000000 272 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x00100000 /* 1M */ 273 #define CONFIG_SYS_PCIE3_IO_VIRT 0xb0100000 /* reuse mem LAW */ 274 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 275 #define CONFIG_SYS_PCIE3_IO_PHYS 0xb0100000 /* reuse mem LAW */ 276 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00100000 /* 1M */ 277 #define CONFIG_SYS_PCIE3_MEM_VIRT2 0xb0200000 278 #define CONFIG_SYS_PCIE3_MEM_BUS2 0xb0200000 279 #define CONFIG_SYS_PCIE3_MEM_PHYS2 0xb0200000 280 #define CONFIG_SYS_PCIE3_MEM_SIZE2 0x00200000 /* 1M */ 281 282 #if defined(CONFIG_PCI) 283 284 /*PCIE video card used*/ 285 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 286 287 /*PCI video card used*/ 288 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ 289 290 /* video */ 291 #define CONFIG_VIDEO 292 293 #if defined(CONFIG_VIDEO) 294 #define CONFIG_BIOSEMU 295 #define CONFIG_CFB_CONSOLE 296 #define CONFIG_VIDEO_SW_CURSOR 297 #define CONFIG_VGA_AS_SINGLE_DEVICE 298 #define CONFIG_ATI_RADEON_FB 299 #define CONFIG_VIDEO_LOGO 300 /*#define CONFIG_CONSOLE_CURSOR*/ 301 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET 302 #endif 303 304 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 305 306 #undef CONFIG_EEPRO100 307 #undef CONFIG_TULIP 308 #define CONFIG_RTL8139 309 310 #ifndef CONFIG_PCI_PNP 311 #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS 312 #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS 313 #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ 314 #endif 315 316 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 317 #define CONFIG_DOS_PARTITION 318 #define CONFIG_SCSI_AHCI 319 320 #ifdef CONFIG_SCSI_AHCI 321 #define CONFIG_LIBATA 322 #define CONFIG_SATA_ULI5288 323 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 324 #define CONFIG_SYS_SCSI_MAX_LUN 1 325 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 326 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 327 #endif /* SCSCI */ 328 329 #endif /* CONFIG_PCI */ 330 331 332 #if defined(CONFIG_TSEC_ENET) 333 334 #define CONFIG_MII 1 /* MII PHY management */ 335 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 336 #define CONFIG_TSEC1 1 337 #define CONFIG_TSEC1_NAME "eTSEC1" 338 #define CONFIG_TSEC3 1 339 #define CONFIG_TSEC3_NAME "eTSEC3" 340 341 #define CONFIG_PIXIS_SGMII_CMD 342 #define CONFIG_FSL_SGMII_RISER 1 343 #define SGMII_RISER_PHY_OFFSET 0x1c 344 345 #define TSEC1_PHY_ADDR 0 346 #define TSEC3_PHY_ADDR 1 347 348 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 349 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 350 351 #define TSEC1_PHYIDX 0 352 #define TSEC3_PHYIDX 0 353 354 #define CONFIG_ETHPRIME "eTSEC1" 355 356 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 357 #endif /* CONFIG_TSEC_ENET */ 358 359 /* 360 * Environment 361 */ 362 #define CONFIG_ENV_IS_IN_FLASH 1 363 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 364 #define CONFIG_ENV_ADDR 0xfff80000 365 #else 366 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x70000) 367 #endif 368 #define CONFIG_ENV_SIZE 0x2000 369 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ 370 371 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 372 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 373 374 /* 375 * BOOTP options 376 */ 377 #define CONFIG_BOOTP_BOOTFILESIZE 378 #define CONFIG_BOOTP_BOOTPATH 379 #define CONFIG_BOOTP_GATEWAY 380 #define CONFIG_BOOTP_HOSTNAME 381 382 383 /* 384 * Command line configuration. 385 */ 386 #define CONFIG_CMD_PING 387 #define CONFIG_CMD_I2C 388 #define CONFIG_CMD_MII 389 #define CONFIG_CMD_IRQ 390 #define CONFIG_CMD_REGINFO 391 392 #if defined(CONFIG_PCI) 393 #define CONFIG_CMD_PCI 394 #define CONFIG_CMD_SCSI 395 #define CONFIG_CMD_EXT2 396 #endif 397 398 /* 399 * USB 400 */ 401 #define CONFIG_USB_EHCI 402 403 #ifdef CONFIG_USB_EHCI 404 #define CONFIG_CMD_USB 405 #define CONFIG_USB_EHCI_PCI 406 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 407 #define CONFIG_USB_STORAGE 408 #define CONFIG_PCI_EHCI_DEVICE 0 409 #endif 410 411 #undef CONFIG_WATCHDOG /* watchdog disabled */ 412 413 /* 414 * Miscellaneous configurable options 415 */ 416 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 417 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 418 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 419 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 420 #if defined(CONFIG_CMD_KGDB) 421 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 422 #else 423 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 424 #endif 425 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 426 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 427 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 428 429 /* 430 * For booting Linux, the board info and command line data 431 * have to be in the first 64 MB of memory, since this is 432 * the maximum mapped by the Linux kernel during initialization. 433 */ 434 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 435 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 436 437 #if defined(CONFIG_CMD_KGDB) 438 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 439 #endif 440 441 /* 442 * Environment Configuration 443 */ 444 445 /* The mac addresses for all ethernet interface */ 446 #if defined(CONFIG_TSEC_ENET) 447 #define CONFIG_HAS_ETH0 448 #define CONFIG_HAS_ETH1 449 #endif 450 451 #define CONFIG_IPADDR 192.168.1.251 452 453 #define CONFIG_HOSTNAME 8544ds_unknown 454 #define CONFIG_ROOTPATH "/nfs/mpc85xx" 455 #define CONFIG_BOOTFILE "8544ds/uImage.uboot" 456 #define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */ 457 458 #define CONFIG_SERVERIP 192.168.1.1 459 #define CONFIG_GATEWAYIP 192.168.1.1 460 #define CONFIG_NETMASK 255.255.0.0 461 462 #define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/ 463 464 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 465 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 466 467 #define CONFIG_BAUDRATE 115200 468 469 #define CONFIG_EXTRA_ENV_SETTINGS \ 470 "netdev=eth0\0" \ 471 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 472 "tftpflash=tftpboot $loadaddr $uboot; " \ 473 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 474 " +$filesize; " \ 475 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 476 " +$filesize; " \ 477 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 478 " $filesize; " \ 479 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 480 " +$filesize; " \ 481 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 482 " $filesize\0" \ 483 "consoledev=ttyS0\0" \ 484 "ramdiskaddr=2000000\0" \ 485 "ramdiskfile=8544ds/ramdisk.uboot\0" \ 486 "fdtaddr=c00000\0" \ 487 "fdtfile=8544ds/mpc8544ds.dtb\0" \ 488 "bdev=sda3\0" 489 490 #define CONFIG_NFSBOOTCOMMAND \ 491 "setenv bootargs root=/dev/nfs rw " \ 492 "nfsroot=$serverip:$rootpath " \ 493 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 494 "console=$consoledev,$baudrate $othbootargs;" \ 495 "tftp $loadaddr $bootfile;" \ 496 "tftp $fdtaddr $fdtfile;" \ 497 "bootm $loadaddr - $fdtaddr" 498 499 #define CONFIG_RAMBOOTCOMMAND \ 500 "setenv bootargs root=/dev/ram rw " \ 501 "console=$consoledev,$baudrate $othbootargs;" \ 502 "tftp $ramdiskaddr $ramdiskfile;" \ 503 "tftp $loadaddr $bootfile;" \ 504 "tftp $fdtaddr $fdtfile;" \ 505 "bootm $loadaddr $ramdiskaddr $fdtaddr" 506 507 #define CONFIG_BOOTCOMMAND \ 508 "setenv bootargs root=/dev/$bdev rw " \ 509 "console=$consoledev,$baudrate $othbootargs;" \ 510 "tftp $loadaddr $bootfile;" \ 511 "tftp $fdtaddr $fdtfile;" \ 512 "bootm $loadaddr - $fdtaddr" 513 514 #endif /* __CONFIG_H */ 515