1 /* 2 * Copyright 2004 Freescale Semiconductor. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8541cds board configuration file 25 * 26 * Please refer to doc/README.mpc85xxcds for more info. 27 * 28 */ 29 #ifndef __CONFIG_H 30 #define __CONFIG_H 31 32 /* High Level Configuration Options */ 33 #define CONFIG_BOOKE 1 /* BOOKE */ 34 #define CONFIG_E500 1 /* BOOKE e500 family */ 35 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ 36 #define CONFIG_CPM2 1 /* has CPM2 */ 37 #define CONFIG_MPC8541 1 /* MPC8541 specific */ 38 #define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */ 39 40 #define CONFIG_SYS_TEXT_BASE 0xfff80000 41 42 #define CONFIG_PCI 43 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 44 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 45 #define CONFIG_ENV_OVERWRITE 46 47 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 48 49 #define CONFIG_FSL_VIA 50 51 #ifndef __ASSEMBLY__ 52 extern unsigned long get_clock_freq(void); 53 #endif 54 #define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ 55 56 /* 57 * These can be toggled for performance analysis, otherwise use default. 58 */ 59 #define CONFIG_L2_CACHE /* toggle L2 cache */ 60 #define CONFIG_BTB /* toggle branch predition */ 61 62 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 63 #define CONFIG_SYS_MEMTEST_END 0x00400000 64 65 /* 66 * Base addresses -- Note these are effective addresses where the 67 * actual resources get mapped (not physical addresses) 68 */ 69 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 70 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 71 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 72 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 73 74 /* DDR Setup */ 75 #define CONFIG_FSL_DDR1 76 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 77 #define CONFIG_DDR_SPD 78 #undef CONFIG_FSL_DDR_INTERACTIVE 79 80 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 81 82 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 83 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 84 85 #define CONFIG_NUM_DDR_CONTROLLERS 1 86 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 87 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 88 89 /* I2C addresses of SPD EEPROMs */ 90 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 91 92 /* 93 * Make sure required options are set 94 */ 95 #ifndef CONFIG_SPD_EEPROM 96 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") 97 #endif 98 99 #undef CONFIG_CLOCKS_IN_MHZ 100 101 /* 102 * Local Bus Definitions 103 */ 104 105 /* 106 * FLASH on the Local Bus 107 * Two banks, 8M each, using the CFI driver. 108 * Boot from BR0/OR0 bank at 0xff00_0000 109 * Alternate BR1/OR1 bank at 0xff80_0000 110 * 111 * BR0, BR1: 112 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 113 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 114 * Port Size = 16 bits = BRx[19:20] = 10 115 * Use GPCM = BRx[24:26] = 000 116 * Valid = BRx[31] = 1 117 * 118 * 0 4 8 12 16 20 24 28 119 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 120 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 121 * 122 * OR0, OR1: 123 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 124 * Reserved ORx[17:18] = 11, confusion here? 125 * CSNT = ORx[20] = 1 126 * ACS = half cycle delay = ORx[21:22] = 11 127 * SCY = 6 = ORx[24:27] = 0110 128 * TRLX = use relaxed timing = ORx[29] = 1 129 * EAD = use external address latch delay = OR[31] = 1 130 * 131 * 0 4 8 12 16 20 24 28 132 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 133 */ 134 135 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ 136 137 #define CONFIG_SYS_BR0_PRELIM 0xff801001 138 #define CONFIG_SYS_BR1_PRELIM 0xff001001 139 140 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 141 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 142 143 #define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} 144 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 145 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 146 #undef CONFIG_SYS_FLASH_CHECKSUM 147 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 148 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 149 150 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 151 152 #define CONFIG_FLASH_CFI_DRIVER 153 #define CONFIG_SYS_FLASH_CFI 154 #define CONFIG_SYS_FLASH_EMPTY_INFO 155 156 157 /* 158 * SDRAM on the Local Bus 159 */ 160 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 161 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 162 163 /* 164 * Base Register 2 and Option Register 2 configure SDRAM. 165 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 166 * 167 * For BR2, need: 168 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 169 * port-size = 32-bits = BR2[19:20] = 11 170 * no parity checking = BR2[21:22] = 00 171 * SDRAM for MSEL = BR2[24:26] = 011 172 * Valid = BR[31] = 1 173 * 174 * 0 4 8 12 16 20 24 28 175 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 176 * 177 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 178 * FIXME: the top 17 bits of BR2. 179 */ 180 181 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 182 183 /* 184 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 185 * 186 * For OR2, need: 187 * 64MB mask for AM, OR2[0:7] = 1111 1100 188 * XAM, OR2[17:18] = 11 189 * 9 columns OR2[19-21] = 010 190 * 13 rows OR2[23-25] = 100 191 * EAD set for extra time OR[31] = 1 192 * 193 * 0 4 8 12 16 20 24 28 194 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 195 */ 196 197 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 198 199 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 200 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 201 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 202 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 203 204 /* 205 * Common settings for all Local Bus SDRAM commands. 206 * At run time, either BSMA1516 (for CPU 1.1) 207 * or BSMA1617 (for CPU 1.0) (old) 208 * is OR'ed in too. 209 */ 210 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 211 | LSDMR_PRETOACT7 \ 212 | LSDMR_ACTTORW7 \ 213 | LSDMR_BL8 \ 214 | LSDMR_WRC4 \ 215 | LSDMR_CL3 \ 216 | LSDMR_RFEN \ 217 ) 218 219 /* 220 * The CADMUS registers are connected to CS3 on CDS. 221 * The new memory map places CADMUS at 0xf8000000. 222 * 223 * For BR3, need: 224 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 225 * port-size = 8-bits = BR[19:20] = 01 226 * no parity checking = BR[21:22] = 00 227 * GPMC for MSEL = BR[24:26] = 000 228 * Valid = BR[31] = 1 229 * 230 * 0 4 8 12 16 20 24 28 231 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 232 * 233 * For OR3, need: 234 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 235 * disable buffer ctrl OR[19] = 0 236 * CSNT OR[20] = 1 237 * ACS OR[21:22] = 11 238 * XACS OR[23] = 1 239 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 240 * SETA OR[28] = 0 241 * TRLX OR[29] = 1 242 * EHTR OR[30] = 1 243 * EAD extra time OR[31] = 1 244 * 245 * 0 4 8 12 16 20 24 28 246 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 247 */ 248 249 #define CONFIG_FSL_CADMUS 250 251 #define CADMUS_BASE_ADDR 0xf8000000 252 #define CONFIG_SYS_BR3_PRELIM 0xf8000801 253 #define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 254 255 #define CONFIG_SYS_INIT_RAM_LOCK 1 256 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 257 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ 258 259 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 260 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 261 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 262 263 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 264 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 265 266 /* Serial Port */ 267 #define CONFIG_CONS_INDEX 2 268 #define CONFIG_SYS_NS16550 269 #define CONFIG_SYS_NS16550_SERIAL 270 #define CONFIG_SYS_NS16550_REG_SIZE 1 271 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 272 273 #define CONFIG_SYS_BAUDRATE_TABLE \ 274 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 275 276 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 277 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 278 279 /* Use the HUSH parser */ 280 #define CONFIG_SYS_HUSH_PARSER 281 #ifdef CONFIG_SYS_HUSH_PARSER 282 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 283 #endif 284 285 /* pass open firmware flat tree */ 286 #define CONFIG_OF_LIBFDT 1 287 #define CONFIG_OF_BOARD_SETUP 1 288 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 289 290 /* 291 * I2C 292 */ 293 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 294 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 295 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 296 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 297 #define CONFIG_SYS_I2C_SLAVE 0x7F 298 #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 299 #define CONFIG_SYS_I2C_OFFSET 0x3000 300 301 /* EEPROM */ 302 #define CONFIG_ID_EEPROM 303 #define CONFIG_SYS_I2C_EEPROM_CCID 304 #define CONFIG_SYS_ID_EEPROM 305 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 306 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 307 308 /* 309 * General PCI 310 * Memory space is mapped 1-1, but I/O space must start from 0. 311 */ 312 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 313 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 314 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 315 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 316 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 317 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 318 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 319 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 320 321 #define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 322 #define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 323 #define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 324 #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ 325 #define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 326 #define CONFIG_SYS_PCI2_IO_BUS 0x00000000 327 #define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 328 #define CONFIG_SYS_PCI2_IO_SIZE 0x100000 /* 1M */ 329 330 #ifdef CONFIG_LEGACY 331 #define BRIDGE_ID 17 332 #define VIA_ID 2 333 #else 334 #define BRIDGE_ID 28 335 #define VIA_ID 4 336 #endif 337 338 #if defined(CONFIG_PCI) 339 340 #define CONFIG_MPC85XX_PCI2 341 #define CONFIG_NET_MULTI 342 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 343 344 #undef CONFIG_EEPRO100 345 #undef CONFIG_TULIP 346 347 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 348 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 349 350 #endif /* CONFIG_PCI */ 351 352 353 #if defined(CONFIG_TSEC_ENET) 354 355 #ifndef CONFIG_NET_MULTI 356 #define CONFIG_NET_MULTI 1 357 #endif 358 359 #define CONFIG_MII 1 /* MII PHY management */ 360 #define CONFIG_TSEC1 1 361 #define CONFIG_TSEC1_NAME "TSEC0" 362 #define CONFIG_TSEC2 1 363 #define CONFIG_TSEC2_NAME "TSEC1" 364 #define TSEC1_PHY_ADDR 0 365 #define TSEC2_PHY_ADDR 1 366 #define TSEC1_PHYIDX 0 367 #define TSEC2_PHYIDX 0 368 #define TSEC1_FLAGS TSEC_GIGABIT 369 #define TSEC2_FLAGS TSEC_GIGABIT 370 371 /* Options are: TSEC[0-1] */ 372 #define CONFIG_ETHPRIME "TSEC0" 373 374 #endif /* CONFIG_TSEC_ENET */ 375 376 /* 377 * Environment 378 */ 379 #define CONFIG_ENV_IS_IN_FLASH 1 380 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 381 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 382 #define CONFIG_ENV_SIZE 0x2000 383 384 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 385 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 386 387 /* 388 * BOOTP options 389 */ 390 #define CONFIG_BOOTP_BOOTFILESIZE 391 #define CONFIG_BOOTP_BOOTPATH 392 #define CONFIG_BOOTP_GATEWAY 393 #define CONFIG_BOOTP_HOSTNAME 394 395 396 /* 397 * Command line configuration. 398 */ 399 #include <config_cmd_default.h> 400 401 #define CONFIG_CMD_PING 402 #define CONFIG_CMD_I2C 403 #define CONFIG_CMD_MII 404 #define CONFIG_CMD_ELF 405 #define CONFIG_CMD_IRQ 406 #define CONFIG_CMD_SETEXPR 407 #define CONFIG_CMD_REGINFO 408 409 #if defined(CONFIG_PCI) 410 #define CONFIG_CMD_PCI 411 #endif 412 413 414 #undef CONFIG_WATCHDOG /* watchdog disabled */ 415 416 /* 417 * Miscellaneous configurable options 418 */ 419 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 420 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 421 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 422 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 423 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 424 #if defined(CONFIG_CMD_KGDB) 425 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 426 #else 427 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 428 #endif 429 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 430 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 431 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 432 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 433 434 /* 435 * For booting Linux, the board info and command line data 436 * have to be in the first 16 MB of memory, since this is 437 * the maximum mapped by the Linux kernel during initialization. 438 */ 439 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 440 441 #if defined(CONFIG_CMD_KGDB) 442 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 443 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 444 #endif 445 446 /* 447 * Environment Configuration 448 */ 449 450 /* The mac addresses for all ethernet interface */ 451 #if defined(CONFIG_TSEC_ENET) 452 #define CONFIG_HAS_ETH0 453 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 454 #define CONFIG_HAS_ETH1 455 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 456 #define CONFIG_HAS_ETH2 457 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 458 #endif 459 460 #define CONFIG_IPADDR 192.168.1.253 461 462 #define CONFIG_HOSTNAME unknown 463 #define CONFIG_ROOTPATH /nfsroot 464 #define CONFIG_BOOTFILE your.uImage 465 466 #define CONFIG_SERVERIP 192.168.1.1 467 #define CONFIG_GATEWAYIP 192.168.1.1 468 #define CONFIG_NETMASK 255.255.255.0 469 470 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 471 472 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 473 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 474 475 #define CONFIG_BAUDRATE 115200 476 477 #define CONFIG_EXTRA_ENV_SETTINGS \ 478 "netdev=eth0\0" \ 479 "consoledev=ttyS1\0" \ 480 "ramdiskaddr=600000\0" \ 481 "ramdiskfile=your.ramdisk.u-boot\0" \ 482 "fdtaddr=400000\0" \ 483 "fdtfile=your.fdt.dtb\0" 484 485 #define CONFIG_NFSBOOTCOMMAND \ 486 "setenv bootargs root=/dev/nfs rw " \ 487 "nfsroot=$serverip:$rootpath " \ 488 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 489 "console=$consoledev,$baudrate $othbootargs;" \ 490 "tftp $loadaddr $bootfile;" \ 491 "tftp $fdtaddr $fdtfile;" \ 492 "bootm $loadaddr - $fdtaddr" 493 494 #define CONFIG_RAMBOOTCOMMAND \ 495 "setenv bootargs root=/dev/ram rw " \ 496 "console=$consoledev,$baudrate $othbootargs;" \ 497 "tftp $ramdiskaddr $ramdiskfile;" \ 498 "tftp $loadaddr $bootfile;" \ 499 "bootm $loadaddr $ramdiskaddr" 500 501 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 502 503 #endif /* __CONFIG_H */ 504