1 /* 2 * Copyright 2004, 2011 Freescale Semiconductor. 3 * 4 * See file CREDITS for list of people who contributed to this 5 * project. 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 of 10 * the License, or (at your option) any later version. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * mpc8541cds board configuration file 25 * 26 * Please refer to doc/README.mpc85xxcds for more info. 27 * 28 */ 29 #ifndef __CONFIG_H 30 #define __CONFIG_H 31 32 /* High Level Configuration Options */ 33 #define CONFIG_BOOKE 1 /* BOOKE */ 34 #define CONFIG_E500 1 /* BOOKE e500 family */ 35 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ 36 #define CONFIG_CPM2 1 /* has CPM2 */ 37 #define CONFIG_MPC8541 1 /* MPC8541 specific */ 38 #define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */ 39 40 #define CONFIG_SYS_TEXT_BASE 0xfff80000 41 42 #define CONFIG_PCI 43 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 44 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 45 #define CONFIG_ENV_OVERWRITE 46 47 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 48 49 #define CONFIG_FSL_VIA 50 51 #ifndef __ASSEMBLY__ 52 extern unsigned long get_clock_freq(void); 53 #endif 54 #define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ 55 56 /* 57 * These can be toggled for performance analysis, otherwise use default. 58 */ 59 #define CONFIG_L2_CACHE /* toggle L2 cache */ 60 #define CONFIG_BTB /* toggle branch predition */ 61 62 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 63 #define CONFIG_SYS_MEMTEST_END 0x00400000 64 65 #define CONFIG_SYS_CCSRBAR 0xe0000000 66 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 67 68 /* DDR Setup */ 69 #define CONFIG_FSL_DDR1 70 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 71 #define CONFIG_DDR_SPD 72 #undef CONFIG_FSL_DDR_INTERACTIVE 73 74 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 75 76 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 77 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 78 79 #define CONFIG_NUM_DDR_CONTROLLERS 1 80 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 81 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 82 83 /* I2C addresses of SPD EEPROMs */ 84 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 85 86 /* 87 * Make sure required options are set 88 */ 89 #ifndef CONFIG_SPD_EEPROM 90 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") 91 #endif 92 93 #undef CONFIG_CLOCKS_IN_MHZ 94 95 /* 96 * Local Bus Definitions 97 */ 98 99 /* 100 * FLASH on the Local Bus 101 * Two banks, 8M each, using the CFI driver. 102 * Boot from BR0/OR0 bank at 0xff00_0000 103 * Alternate BR1/OR1 bank at 0xff80_0000 104 * 105 * BR0, BR1: 106 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 107 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 108 * Port Size = 16 bits = BRx[19:20] = 10 109 * Use GPCM = BRx[24:26] = 000 110 * Valid = BRx[31] = 1 111 * 112 * 0 4 8 12 16 20 24 28 113 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 114 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 115 * 116 * OR0, OR1: 117 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 118 * Reserved ORx[17:18] = 11, confusion here? 119 * CSNT = ORx[20] = 1 120 * ACS = half cycle delay = ORx[21:22] = 11 121 * SCY = 6 = ORx[24:27] = 0110 122 * TRLX = use relaxed timing = ORx[29] = 1 123 * EAD = use external address latch delay = OR[31] = 1 124 * 125 * 0 4 8 12 16 20 24 28 126 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 127 */ 128 129 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ 130 131 #define CONFIG_SYS_BR0_PRELIM 0xff801001 132 #define CONFIG_SYS_BR1_PRELIM 0xff001001 133 134 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 135 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 136 137 #define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} 138 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 139 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 140 #undef CONFIG_SYS_FLASH_CHECKSUM 141 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 142 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 143 144 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 145 146 #define CONFIG_FLASH_CFI_DRIVER 147 #define CONFIG_SYS_FLASH_CFI 148 #define CONFIG_SYS_FLASH_EMPTY_INFO 149 150 151 /* 152 * SDRAM on the Local Bus 153 */ 154 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 155 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 156 157 /* 158 * Base Register 2 and Option Register 2 configure SDRAM. 159 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 160 * 161 * For BR2, need: 162 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 163 * port-size = 32-bits = BR2[19:20] = 11 164 * no parity checking = BR2[21:22] = 00 165 * SDRAM for MSEL = BR2[24:26] = 011 166 * Valid = BR[31] = 1 167 * 168 * 0 4 8 12 16 20 24 28 169 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 170 * 171 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 172 * FIXME: the top 17 bits of BR2. 173 */ 174 175 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 176 177 /* 178 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 179 * 180 * For OR2, need: 181 * 64MB mask for AM, OR2[0:7] = 1111 1100 182 * XAM, OR2[17:18] = 11 183 * 9 columns OR2[19-21] = 010 184 * 13 rows OR2[23-25] = 100 185 * EAD set for extra time OR[31] = 1 186 * 187 * 0 4 8 12 16 20 24 28 188 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 189 */ 190 191 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 192 193 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 194 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 195 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 196 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 197 198 /* 199 * Common settings for all Local Bus SDRAM commands. 200 * At run time, either BSMA1516 (for CPU 1.1) 201 * or BSMA1617 (for CPU 1.0) (old) 202 * is OR'ed in too. 203 */ 204 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 205 | LSDMR_PRETOACT7 \ 206 | LSDMR_ACTTORW7 \ 207 | LSDMR_BL8 \ 208 | LSDMR_WRC4 \ 209 | LSDMR_CL3 \ 210 | LSDMR_RFEN \ 211 ) 212 213 /* 214 * The CADMUS registers are connected to CS3 on CDS. 215 * The new memory map places CADMUS at 0xf8000000. 216 * 217 * For BR3, need: 218 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 219 * port-size = 8-bits = BR[19:20] = 01 220 * no parity checking = BR[21:22] = 00 221 * GPMC for MSEL = BR[24:26] = 000 222 * Valid = BR[31] = 1 223 * 224 * 0 4 8 12 16 20 24 28 225 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 226 * 227 * For OR3, need: 228 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 229 * disable buffer ctrl OR[19] = 0 230 * CSNT OR[20] = 1 231 * ACS OR[21:22] = 11 232 * XACS OR[23] = 1 233 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 234 * SETA OR[28] = 0 235 * TRLX OR[29] = 1 236 * EHTR OR[30] = 1 237 * EAD extra time OR[31] = 1 238 * 239 * 0 4 8 12 16 20 24 28 240 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 241 */ 242 243 #define CONFIG_FSL_CADMUS 244 245 #define CADMUS_BASE_ADDR 0xf8000000 246 #define CONFIG_SYS_BR3_PRELIM 0xf8000801 247 #define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 248 249 #define CONFIG_SYS_INIT_RAM_LOCK 1 250 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 251 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 252 253 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 254 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 255 256 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 257 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 258 259 /* Serial Port */ 260 #define CONFIG_CONS_INDEX 2 261 #define CONFIG_SYS_NS16550 262 #define CONFIG_SYS_NS16550_SERIAL 263 #define CONFIG_SYS_NS16550_REG_SIZE 1 264 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 265 266 #define CONFIG_SYS_BAUDRATE_TABLE \ 267 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 268 269 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 270 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 271 272 /* Use the HUSH parser */ 273 #define CONFIG_SYS_HUSH_PARSER 274 #ifdef CONFIG_SYS_HUSH_PARSER 275 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 276 #endif 277 278 /* pass open firmware flat tree */ 279 #define CONFIG_OF_LIBFDT 1 280 #define CONFIG_OF_BOARD_SETUP 1 281 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 282 283 /* 284 * I2C 285 */ 286 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 287 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 288 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 289 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 290 #define CONFIG_SYS_I2C_SLAVE 0x7F 291 #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 292 #define CONFIG_SYS_I2C_OFFSET 0x3000 293 294 /* EEPROM */ 295 #define CONFIG_ID_EEPROM 296 #define CONFIG_SYS_I2C_EEPROM_CCID 297 #define CONFIG_SYS_ID_EEPROM 298 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 299 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 300 301 /* 302 * General PCI 303 * Memory space is mapped 1-1, but I/O space must start from 0. 304 */ 305 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 306 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 307 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 308 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 309 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 310 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 311 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 312 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 313 314 #define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 315 #define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 316 #define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 317 #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ 318 #define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 319 #define CONFIG_SYS_PCI2_IO_BUS 0x00000000 320 #define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 321 #define CONFIG_SYS_PCI2_IO_SIZE 0x100000 /* 1M */ 322 323 #ifdef CONFIG_LEGACY 324 #define BRIDGE_ID 17 325 #define VIA_ID 2 326 #else 327 #define BRIDGE_ID 28 328 #define VIA_ID 4 329 #endif 330 331 #if defined(CONFIG_PCI) 332 333 #define CONFIG_MPC85XX_PCI2 334 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 335 336 #undef CONFIG_EEPRO100 337 #undef CONFIG_TULIP 338 339 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 340 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 341 342 #endif /* CONFIG_PCI */ 343 344 345 #if defined(CONFIG_TSEC_ENET) 346 347 #define CONFIG_MII 1 /* MII PHY management */ 348 #define CONFIG_TSEC1 1 349 #define CONFIG_TSEC1_NAME "TSEC0" 350 #define CONFIG_TSEC2 1 351 #define CONFIG_TSEC2_NAME "TSEC1" 352 #define TSEC1_PHY_ADDR 0 353 #define TSEC2_PHY_ADDR 1 354 #define TSEC1_PHYIDX 0 355 #define TSEC2_PHYIDX 0 356 #define TSEC1_FLAGS TSEC_GIGABIT 357 #define TSEC2_FLAGS TSEC_GIGABIT 358 359 /* Options are: TSEC[0-1] */ 360 #define CONFIG_ETHPRIME "TSEC0" 361 362 #endif /* CONFIG_TSEC_ENET */ 363 364 /* 365 * Environment 366 */ 367 #define CONFIG_ENV_IS_IN_FLASH 1 368 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 369 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 370 #define CONFIG_ENV_SIZE 0x2000 371 372 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 373 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 374 375 /* 376 * BOOTP options 377 */ 378 #define CONFIG_BOOTP_BOOTFILESIZE 379 #define CONFIG_BOOTP_BOOTPATH 380 #define CONFIG_BOOTP_GATEWAY 381 #define CONFIG_BOOTP_HOSTNAME 382 383 384 /* 385 * Command line configuration. 386 */ 387 #include <config_cmd_default.h> 388 389 #define CONFIG_CMD_PING 390 #define CONFIG_CMD_I2C 391 #define CONFIG_CMD_MII 392 #define CONFIG_CMD_ELF 393 #define CONFIG_CMD_IRQ 394 #define CONFIG_CMD_SETEXPR 395 #define CONFIG_CMD_REGINFO 396 397 #if defined(CONFIG_PCI) 398 #define CONFIG_CMD_PCI 399 #endif 400 401 402 #undef CONFIG_WATCHDOG /* watchdog disabled */ 403 404 /* 405 * Miscellaneous configurable options 406 */ 407 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 408 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 409 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 410 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 411 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 412 #if defined(CONFIG_CMD_KGDB) 413 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 414 #else 415 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 416 #endif 417 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 418 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 419 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 420 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 421 422 /* 423 * For booting Linux, the board info and command line data 424 * have to be in the first 64 MB of memory, since this is 425 * the maximum mapped by the Linux kernel during initialization. 426 */ 427 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 428 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 429 430 #if defined(CONFIG_CMD_KGDB) 431 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 432 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 433 #endif 434 435 /* 436 * Environment Configuration 437 */ 438 439 /* The mac addresses for all ethernet interface */ 440 #if defined(CONFIG_TSEC_ENET) 441 #define CONFIG_HAS_ETH0 442 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 443 #define CONFIG_HAS_ETH1 444 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 445 #define CONFIG_HAS_ETH2 446 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 447 #endif 448 449 #define CONFIG_IPADDR 192.168.1.253 450 451 #define CONFIG_HOSTNAME unknown 452 #define CONFIG_ROOTPATH /nfsroot 453 #define CONFIG_BOOTFILE your.uImage 454 455 #define CONFIG_SERVERIP 192.168.1.1 456 #define CONFIG_GATEWAYIP 192.168.1.1 457 #define CONFIG_NETMASK 255.255.255.0 458 459 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 460 461 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 462 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 463 464 #define CONFIG_BAUDRATE 115200 465 466 #define CONFIG_EXTRA_ENV_SETTINGS \ 467 "netdev=eth0\0" \ 468 "consoledev=ttyS1\0" \ 469 "ramdiskaddr=600000\0" \ 470 "ramdiskfile=your.ramdisk.u-boot\0" \ 471 "fdtaddr=400000\0" \ 472 "fdtfile=your.fdt.dtb\0" 473 474 #define CONFIG_NFSBOOTCOMMAND \ 475 "setenv bootargs root=/dev/nfs rw " \ 476 "nfsroot=$serverip:$rootpath " \ 477 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 478 "console=$consoledev,$baudrate $othbootargs;" \ 479 "tftp $loadaddr $bootfile;" \ 480 "tftp $fdtaddr $fdtfile;" \ 481 "bootm $loadaddr - $fdtaddr" 482 483 #define CONFIG_RAMBOOTCOMMAND \ 484 "setenv bootargs root=/dev/ram rw " \ 485 "console=$consoledev,$baudrate $othbootargs;" \ 486 "tftp $ramdiskaddr $ramdiskfile;" \ 487 "tftp $loadaddr $bootfile;" \ 488 "bootm $loadaddr $ramdiskaddr" 489 490 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 491 492 #endif /* __CONFIG_H */ 493