1 /* 2 * Copyright 2004, 2011 Freescale Semiconductor. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8541cds board configuration file 9 * 10 * Please refer to doc/README.mpc85xxcds for more info. 11 * 12 */ 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #define CONFIG_DISPLAY_BOARDINFO 17 18 /* High Level Configuration Options */ 19 #define CONFIG_BOOKE 1 /* BOOKE */ 20 #define CONFIG_E500 1 /* BOOKE e500 family */ 21 #define CONFIG_CPM2 1 /* has CPM2 */ 22 #define CONFIG_MPC8541 1 /* MPC8541 specific */ 23 #define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */ 24 25 #define CONFIG_SYS_TEXT_BASE 0xfff80000 26 27 #define CONFIG_PCI 28 #define CONFIG_PCI_INDIRECT_BRIDGE 29 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 30 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 31 #define CONFIG_ENV_OVERWRITE 32 33 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 34 35 #define CONFIG_FSL_VIA 36 37 #ifndef __ASSEMBLY__ 38 extern unsigned long get_clock_freq(void); 39 #endif 40 #define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ 41 42 /* 43 * These can be toggled for performance analysis, otherwise use default. 44 */ 45 #define CONFIG_L2_CACHE /* toggle L2 cache */ 46 #define CONFIG_BTB /* toggle branch predition */ 47 48 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 49 #define CONFIG_SYS_MEMTEST_END 0x00400000 50 51 #define CONFIG_SYS_CCSRBAR 0xe0000000 52 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 53 54 /* DDR Setup */ 55 #define CONFIG_SYS_FSL_DDR1 56 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 57 #define CONFIG_DDR_SPD 58 #undef CONFIG_FSL_DDR_INTERACTIVE 59 60 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 61 62 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 63 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 64 65 #define CONFIG_NUM_DDR_CONTROLLERS 1 66 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 67 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 68 69 /* I2C addresses of SPD EEPROMs */ 70 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 71 72 /* 73 * Make sure required options are set 74 */ 75 #ifndef CONFIG_SPD_EEPROM 76 #error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") 77 #endif 78 79 #undef CONFIG_CLOCKS_IN_MHZ 80 81 /* 82 * Local Bus Definitions 83 */ 84 85 /* 86 * FLASH on the Local Bus 87 * Two banks, 8M each, using the CFI driver. 88 * Boot from BR0/OR0 bank at 0xff00_0000 89 * Alternate BR1/OR1 bank at 0xff80_0000 90 * 91 * BR0, BR1: 92 * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 93 * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 94 * Port Size = 16 bits = BRx[19:20] = 10 95 * Use GPCM = BRx[24:26] = 000 96 * Valid = BRx[31] = 1 97 * 98 * 0 4 8 12 16 20 24 28 99 * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 100 * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 101 * 102 * OR0, OR1: 103 * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 104 * Reserved ORx[17:18] = 11, confusion here? 105 * CSNT = ORx[20] = 1 106 * ACS = half cycle delay = ORx[21:22] = 11 107 * SCY = 6 = ORx[24:27] = 0110 108 * TRLX = use relaxed timing = ORx[29] = 1 109 * EAD = use external address latch delay = OR[31] = 1 110 * 111 * 0 4 8 12 16 20 24 28 112 * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx 113 */ 114 115 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ 116 117 #define CONFIG_SYS_BR0_PRELIM 0xff801001 118 #define CONFIG_SYS_BR1_PRELIM 0xff001001 119 120 #define CONFIG_SYS_OR0_PRELIM 0xff806e65 121 #define CONFIG_SYS_OR1_PRELIM 0xff806e65 122 123 #define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} 124 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 125 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 126 #undef CONFIG_SYS_FLASH_CHECKSUM 127 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 128 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 129 130 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 131 132 #define CONFIG_FLASH_CFI_DRIVER 133 #define CONFIG_SYS_FLASH_CFI 134 #define CONFIG_SYS_FLASH_EMPTY_INFO 135 136 137 /* 138 * SDRAM on the Local Bus 139 */ 140 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 141 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 142 143 /* 144 * Base Register 2 and Option Register 2 configure SDRAM. 145 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 146 * 147 * For BR2, need: 148 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 149 * port-size = 32-bits = BR2[19:20] = 11 150 * no parity checking = BR2[21:22] = 00 151 * SDRAM for MSEL = BR2[24:26] = 011 152 * Valid = BR[31] = 1 153 * 154 * 0 4 8 12 16 20 24 28 155 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 156 * 157 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 158 * FIXME: the top 17 bits of BR2. 159 */ 160 161 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 162 163 /* 164 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 165 * 166 * For OR2, need: 167 * 64MB mask for AM, OR2[0:7] = 1111 1100 168 * XAM, OR2[17:18] = 11 169 * 9 columns OR2[19-21] = 010 170 * 13 rows OR2[23-25] = 100 171 * EAD set for extra time OR[31] = 1 172 * 173 * 0 4 8 12 16 20 24 28 174 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 175 */ 176 177 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 178 179 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 180 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 181 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 182 #define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ 183 184 /* 185 * Common settings for all Local Bus SDRAM commands. 186 * At run time, either BSMA1516 (for CPU 1.1) 187 * or BSMA1617 (for CPU 1.0) (old) 188 * is OR'ed in too. 189 */ 190 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ 191 | LSDMR_PRETOACT7 \ 192 | LSDMR_ACTTORW7 \ 193 | LSDMR_BL8 \ 194 | LSDMR_WRC4 \ 195 | LSDMR_CL3 \ 196 | LSDMR_RFEN \ 197 ) 198 199 /* 200 * The CADMUS registers are connected to CS3 on CDS. 201 * The new memory map places CADMUS at 0xf8000000. 202 * 203 * For BR3, need: 204 * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 205 * port-size = 8-bits = BR[19:20] = 01 206 * no parity checking = BR[21:22] = 00 207 * GPMC for MSEL = BR[24:26] = 000 208 * Valid = BR[31] = 1 209 * 210 * 0 4 8 12 16 20 24 28 211 * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 212 * 213 * For OR3, need: 214 * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 215 * disable buffer ctrl OR[19] = 0 216 * CSNT OR[20] = 1 217 * ACS OR[21:22] = 11 218 * XACS OR[23] = 1 219 * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe 220 * SETA OR[28] = 0 221 * TRLX OR[29] = 1 222 * EHTR OR[30] = 1 223 * EAD extra time OR[31] = 1 224 * 225 * 0 4 8 12 16 20 24 28 226 * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 227 */ 228 229 #define CONFIG_FSL_CADMUS 230 231 #define CADMUS_BASE_ADDR 0xf8000000 232 #define CONFIG_SYS_BR3_PRELIM 0xf8000801 233 #define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 234 235 #define CONFIG_SYS_INIT_RAM_LOCK 1 236 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 237 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 238 239 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 240 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 241 242 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 243 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 244 245 /* Serial Port */ 246 #define CONFIG_CONS_INDEX 2 247 #define CONFIG_SYS_NS16550_SERIAL 248 #define CONFIG_SYS_NS16550_REG_SIZE 1 249 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 250 251 #define CONFIG_SYS_BAUDRATE_TABLE \ 252 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 253 254 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 255 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 256 257 /* Use the HUSH parser */ 258 #define CONFIG_SYS_HUSH_PARSER 259 #ifdef CONFIG_SYS_HUSH_PARSER 260 #endif 261 262 /* 263 * I2C 264 */ 265 #define CONFIG_SYS_I2C 266 #define CONFIG_SYS_I2C_FSL 267 #define CONFIG_SYS_FSL_I2C_SPEED 400000 268 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 269 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 270 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 271 272 /* EEPROM */ 273 #define CONFIG_ID_EEPROM 274 #define CONFIG_SYS_I2C_EEPROM_CCID 275 #define CONFIG_SYS_ID_EEPROM 276 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 277 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 278 279 /* 280 * General PCI 281 * Memory space is mapped 1-1, but I/O space must start from 0. 282 */ 283 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 284 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 285 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 286 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 287 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 288 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 289 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 290 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 291 292 #define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 293 #define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 294 #define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 295 #define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ 296 #define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 297 #define CONFIG_SYS_PCI2_IO_BUS 0x00000000 298 #define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 299 #define CONFIG_SYS_PCI2_IO_SIZE 0x100000 /* 1M */ 300 301 #ifdef CONFIG_LEGACY 302 #define BRIDGE_ID 17 303 #define VIA_ID 2 304 #else 305 #define BRIDGE_ID 28 306 #define VIA_ID 4 307 #endif 308 309 #if defined(CONFIG_PCI) 310 311 #define CONFIG_MPC85XX_PCI2 312 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 313 314 #undef CONFIG_EEPRO100 315 #undef CONFIG_TULIP 316 317 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 318 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 319 320 #endif /* CONFIG_PCI */ 321 322 323 #if defined(CONFIG_TSEC_ENET) 324 325 #define CONFIG_MII 1 /* MII PHY management */ 326 #define CONFIG_TSEC1 1 327 #define CONFIG_TSEC1_NAME "TSEC0" 328 #define CONFIG_TSEC2 1 329 #define CONFIG_TSEC2_NAME "TSEC1" 330 #define TSEC1_PHY_ADDR 0 331 #define TSEC2_PHY_ADDR 1 332 #define TSEC1_PHYIDX 0 333 #define TSEC2_PHYIDX 0 334 #define TSEC1_FLAGS TSEC_GIGABIT 335 #define TSEC2_FLAGS TSEC_GIGABIT 336 337 /* Options are: TSEC[0-1] */ 338 #define CONFIG_ETHPRIME "TSEC0" 339 340 #endif /* CONFIG_TSEC_ENET */ 341 342 /* 343 * Environment 344 */ 345 #define CONFIG_ENV_IS_IN_FLASH 1 346 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 347 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 348 #define CONFIG_ENV_SIZE 0x2000 349 350 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 351 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 352 353 /* 354 * BOOTP options 355 */ 356 #define CONFIG_BOOTP_BOOTFILESIZE 357 #define CONFIG_BOOTP_BOOTPATH 358 #define CONFIG_BOOTP_GATEWAY 359 #define CONFIG_BOOTP_HOSTNAME 360 361 362 /* 363 * Command line configuration. 364 */ 365 #define CONFIG_CMD_PING 366 #define CONFIG_CMD_I2C 367 #define CONFIG_CMD_MII 368 #define CONFIG_CMD_IRQ 369 #define CONFIG_CMD_REGINFO 370 371 #if defined(CONFIG_PCI) 372 #define CONFIG_CMD_PCI 373 #endif 374 375 376 #undef CONFIG_WATCHDOG /* watchdog disabled */ 377 378 /* 379 * Miscellaneous configurable options 380 */ 381 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 382 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 383 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 384 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 385 #if defined(CONFIG_CMD_KGDB) 386 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 387 #else 388 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 389 #endif 390 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 391 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 392 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 393 394 /* 395 * For booting Linux, the board info and command line data 396 * have to be in the first 64 MB of memory, since this is 397 * the maximum mapped by the Linux kernel during initialization. 398 */ 399 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ 400 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 401 402 #if defined(CONFIG_CMD_KGDB) 403 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 404 #endif 405 406 /* 407 * Environment Configuration 408 */ 409 410 /* The mac addresses for all ethernet interface */ 411 #if defined(CONFIG_TSEC_ENET) 412 #define CONFIG_HAS_ETH0 413 #define CONFIG_HAS_ETH1 414 #define CONFIG_HAS_ETH2 415 #endif 416 417 #define CONFIG_IPADDR 192.168.1.253 418 419 #define CONFIG_HOSTNAME unknown 420 #define CONFIG_ROOTPATH "/nfsroot" 421 #define CONFIG_BOOTFILE "your.uImage" 422 423 #define CONFIG_SERVERIP 192.168.1.1 424 #define CONFIG_GATEWAYIP 192.168.1.1 425 #define CONFIG_NETMASK 255.255.255.0 426 427 #define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ 428 429 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 430 #undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ 431 432 #define CONFIG_BAUDRATE 115200 433 434 #define CONFIG_EXTRA_ENV_SETTINGS \ 435 "netdev=eth0\0" \ 436 "consoledev=ttyS1\0" \ 437 "ramdiskaddr=600000\0" \ 438 "ramdiskfile=your.ramdisk.u-boot\0" \ 439 "fdtaddr=400000\0" \ 440 "fdtfile=your.fdt.dtb\0" 441 442 #define CONFIG_NFSBOOTCOMMAND \ 443 "setenv bootargs root=/dev/nfs rw " \ 444 "nfsroot=$serverip:$rootpath " \ 445 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 446 "console=$consoledev,$baudrate $othbootargs;" \ 447 "tftp $loadaddr $bootfile;" \ 448 "tftp $fdtaddr $fdtfile;" \ 449 "bootm $loadaddr - $fdtaddr" 450 451 #define CONFIG_RAMBOOTCOMMAND \ 452 "setenv bootargs root=/dev/ram rw " \ 453 "console=$consoledev,$baudrate $othbootargs;" \ 454 "tftp $ramdiskaddr $ramdiskfile;" \ 455 "tftp $loadaddr $bootfile;" \ 456 "bootm $loadaddr $ramdiskaddr" 457 458 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 459 460 #endif /* __CONFIG_H */ 461