1 /* 2 * Copyright 2004 Freescale Semiconductor. 3 * (C) Copyright 2002,2003 Motorola,Inc. 4 * Xianghua Xiao <X.Xiao@motorola.com> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 /* 26 * mpc8540ads board configuration file 27 * 28 * Please refer to doc/README.mpc85xx for more info. 29 * 30 * Make sure you change the MAC address and other network params first, 31 * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. 32 */ 33 34 #ifndef __CONFIG_H 35 #define __CONFIG_H 36 37 /* High Level Configuration Options */ 38 #define CONFIG_BOOKE 1 /* BOOKE */ 39 #define CONFIG_E500 1 /* BOOKE e500 family */ 40 #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ 41 #define CONFIG_MPC8540 1 /* MPC8540 specific */ 42 #define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific */ 43 44 #ifndef CONFIG_HAS_FEC 45 #define CONFIG_HAS_FEC 1 /* 8540 has FEC */ 46 #endif 47 48 #define CONFIG_PCI 49 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 50 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 51 #define CONFIG_ENV_OVERWRITE 52 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 53 54 /* 55 * sysclk for MPC85xx 56 * 57 * Two valid values are: 58 * 33000000 59 * 66000000 60 * 61 * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz 62 * is likely the desired value here, so that is now the default. 63 * The board, however, can run at 66MHz. In any event, this value 64 * must match the settings of some switches. Details can be found 65 * in the README.mpc85xxads. 66 * 67 * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to 68 * 33MHz to accommodate, based on a PCI pin. 69 * Note that PCI-X won't work at 33MHz. 70 */ 71 72 #ifndef CONFIG_SYS_CLK_FREQ 73 #define CONFIG_SYS_CLK_FREQ 33000000 74 #endif 75 76 77 /* 78 * These can be toggled for performance analysis, otherwise use default. 79 */ 80 #define CONFIG_L2_CACHE /* toggle L2 cache */ 81 #define CONFIG_BTB /* toggle branch predition */ 82 83 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 84 #define CONFIG_SYS_MEMTEST_END 0x00400000 85 86 87 /* 88 * Base addresses -- Note these are effective addresses where the 89 * actual resources get mapped (not physical addresses) 90 */ 91 #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ 92 #define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ 93 #define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ 94 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 95 96 /* DDR Setup */ 97 #define CONFIG_FSL_DDR1 98 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ 99 #define CONFIG_DDR_SPD 100 #undef CONFIG_FSL_DDR_INTERACTIVE 101 102 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 103 104 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 105 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 106 107 #define CONFIG_NUM_DDR_CONTROLLERS 1 108 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 109 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 110 111 /* I2C addresses of SPD EEPROMs */ 112 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 113 114 /* These are used when DDR doesn't use SPD. */ 115 #define CONFIG_SYS_SDRAM_SIZE 128 /* DDR is 128MB */ 116 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ 117 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80000002 118 #define CONFIG_SYS_DDR_TIMING_1 0x37344321 119 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 120 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 121 #define CONFIG_SYS_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ 122 #define CONFIG_SYS_DDR_INTERVAL 0x05200100 /* autocharge,no open page */ 123 124 /* 125 * SDRAM on the Local Bus 126 */ 127 #define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ 128 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 129 130 #define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ 131 #define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ 132 133 #define CONFIG_SYS_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ 134 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 135 #define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */ 136 #undef CONFIG_SYS_FLASH_CHECKSUM 137 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 138 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 139 140 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ 141 142 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 143 #define CONFIG_SYS_RAMBOOT 144 #else 145 #undef CONFIG_SYS_RAMBOOT 146 #endif 147 148 #define CONFIG_FLASH_CFI_DRIVER 149 #define CONFIG_SYS_FLASH_CFI 150 #define CONFIG_SYS_FLASH_EMPTY_INFO 151 152 #undef CONFIG_CLOCKS_IN_MHZ 153 154 155 /* 156 * Local Bus Definitions 157 */ 158 159 /* 160 * Base Register 2 and Option Register 2 configure SDRAM. 161 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 162 * 163 * For BR2, need: 164 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 165 * port-size = 32-bits = BR2[19:20] = 11 166 * no parity checking = BR2[21:22] = 00 167 * SDRAM for MSEL = BR2[24:26] = 011 168 * Valid = BR[31] = 1 169 * 170 * 0 4 8 12 16 20 24 28 171 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 172 * 173 * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 174 * FIXME: the top 17 bits of BR2. 175 */ 176 177 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 178 179 /* 180 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 181 * 182 * For OR2, need: 183 * 64MB mask for AM, OR2[0:7] = 1111 1100 184 * XAM, OR2[17:18] = 11 185 * 9 columns OR2[19-21] = 010 186 * 13 rows OR2[23-25] = 100 187 * EAD set for extra time OR[31] = 1 188 * 189 * 0 4 8 12 16 20 24 28 190 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 191 */ 192 193 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 194 195 #define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ 196 #define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ 197 #define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ 198 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ 199 200 #define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_BSMA1516 \ 201 | LSDMR_RFCR5 \ 202 | LSDMR_PRETOACT3 \ 203 | LSDMR_ACTTORW3 \ 204 | LSDMR_BL8 \ 205 | LSDMR_WRC2 \ 206 | LSDMR_CL3 \ 207 | LSDMR_RFEN \ 208 ) 209 210 /* 211 * SDRAM Controller configuration sequence. 212 */ 213 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) 214 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 215 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 216 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) 217 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) 218 219 220 /* 221 * 32KB, 8-bit wide for ADS config reg 222 */ 223 #define CONFIG_SYS_BR4_PRELIM 0xf8000801 224 #define CONFIG_SYS_OR4_PRELIM 0xffffe1f1 225 #define CONFIG_SYS_BCSR (CONFIG_SYS_BR4_PRELIM & 0xffff8000) 226 227 #define CONFIG_SYS_INIT_RAM_LOCK 1 228 #define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ 229 #define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ 230 231 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ 232 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) 233 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 234 235 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 236 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 237 238 /* Serial Port */ 239 #define CONFIG_CONS_INDEX 1 240 #undef CONFIG_SERIAL_SOFTWARE_FIFO 241 #define CONFIG_SYS_NS16550 242 #define CONFIG_SYS_NS16550_SERIAL 243 #define CONFIG_SYS_NS16550_REG_SIZE 1 244 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 245 246 #define CONFIG_SYS_BAUDRATE_TABLE \ 247 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 248 249 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 250 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 251 252 /* Use the HUSH parser */ 253 #define CONFIG_SYS_HUSH_PARSER 254 #ifdef CONFIG_SYS_HUSH_PARSER 255 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 256 #endif 257 258 /* pass open firmware flat tree */ 259 #define CONFIG_OF_LIBFDT 1 260 #define CONFIG_OF_BOARD_SETUP 1 261 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 262 263 /* 264 * I2C 265 */ 266 #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ 267 #define CONFIG_HARD_I2C /* I2C with hardware support*/ 268 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 269 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 270 #define CONFIG_SYS_I2C_SLAVE 0x7F 271 #define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ 272 #define CONFIG_SYS_I2C_OFFSET 0x3000 273 274 /* RapidIO MMU */ 275 #define CONFIG_SYS_RIO_MEM_VIRT 0xc0000000 /* base address */ 276 #define CONFIG_SYS_RIO_MEM_BUS 0xc0000000 /* base address */ 277 #define CONFIG_SYS_RIO_MEM_PHYS 0xc0000000 278 #define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ 279 280 /* 281 * General PCI 282 * Memory space is mapped 1-1, but I/O space must start from 0. 283 */ 284 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 285 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 286 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 287 #define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ 288 #define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 289 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 290 #define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 291 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 292 293 #if defined(CONFIG_PCI) 294 295 #define CONFIG_NET_MULTI 296 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 297 298 #undef CONFIG_EEPRO100 299 #undef CONFIG_TULIP 300 301 #if !defined(CONFIG_PCI_PNP) 302 #define PCI_ENET0_IOADDR 0xe0000000 303 #define PCI_ENET0_MEMADDR 0xe0000000 304 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 305 #endif 306 307 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 308 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ 309 310 #endif /* CONFIG_PCI */ 311 312 313 #if defined(CONFIG_TSEC_ENET) 314 315 #ifndef CONFIG_NET_MULTI 316 #define CONFIG_NET_MULTI 1 317 #endif 318 319 #define CONFIG_MII 1 /* MII PHY management */ 320 #define CONFIG_TSEC1 1 321 #define CONFIG_TSEC1_NAME "TSEC0" 322 #define CONFIG_TSEC2 1 323 #define CONFIG_TSEC2_NAME "TSEC1" 324 #define TSEC1_PHY_ADDR 0 325 #define TSEC2_PHY_ADDR 1 326 #define TSEC1_PHYIDX 0 327 #define TSEC2_PHYIDX 0 328 #define TSEC1_FLAGS TSEC_GIGABIT 329 #define TSEC2_FLAGS TSEC_GIGABIT 330 331 332 #if CONFIG_HAS_FEC 333 #define CONFIG_MPC85XX_FEC 1 334 #define CONFIG_MPC85XX_FEC_NAME "FEC" 335 #define FEC_PHY_ADDR 3 336 #define FEC_PHYIDX 0 337 #define FEC_FLAGS 0 338 #endif 339 340 /* Options are: TSEC[0-1], FEC */ 341 #define CONFIG_ETHPRIME "TSEC0" 342 343 #endif /* CONFIG_TSEC_ENET */ 344 345 346 /* 347 * Environment 348 */ 349 #ifndef CONFIG_SYS_RAMBOOT 350 #define CONFIG_ENV_IS_IN_FLASH 1 351 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) 352 #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ 353 #define CONFIG_ENV_SIZE 0x2000 354 #else 355 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 356 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 357 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 358 #define CONFIG_ENV_SIZE 0x2000 359 #endif 360 361 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 362 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 363 364 365 /* 366 * BOOTP options 367 */ 368 #define CONFIG_BOOTP_BOOTFILESIZE 369 #define CONFIG_BOOTP_BOOTPATH 370 #define CONFIG_BOOTP_GATEWAY 371 #define CONFIG_BOOTP_HOSTNAME 372 373 374 /* 375 * Command line configuration. 376 */ 377 #include <config_cmd_default.h> 378 379 #define CONFIG_CMD_PING 380 #define CONFIG_CMD_I2C 381 #define CONFIG_CMD_ELF 382 #define CONFIG_CMD_IRQ 383 #define CONFIG_CMD_SETEXPR 384 385 #if defined(CONFIG_PCI) 386 #define CONFIG_CMD_PCI 387 #endif 388 389 #if defined(CONFIG_SYS_RAMBOOT) 390 #undef CONFIG_CMD_SAVEENV 391 #undef CONFIG_CMD_LOADS 392 #endif 393 394 395 #undef CONFIG_WATCHDOG /* watchdog disabled */ 396 397 /* 398 * Miscellaneous configurable options 399 */ 400 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 401 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 402 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 403 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 404 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 405 406 #if defined(CONFIG_CMD_KGDB) 407 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 408 #else 409 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 410 #endif 411 412 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 413 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 414 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 415 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 416 417 /* 418 * For booting Linux, the board info and command line data 419 * have to be in the first 16 MB of memory, since this is 420 * the maximum mapped by the Linux kernel during initialization. 421 */ 422 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 423 424 /* 425 * Internal Definitions 426 * 427 * Boot Flags 428 */ 429 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 430 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 431 432 #if defined(CONFIG_CMD_KGDB) 433 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 434 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 435 #endif 436 437 438 /* 439 * Environment Configuration 440 */ 441 442 /* The mac addresses for all ethernet interface */ 443 #if defined(CONFIG_TSEC_ENET) 444 #define CONFIG_HAS_ETH0 445 #define CONFIG_ETHADDR 00:E0:0C:00:00:FD 446 #define CONFIG_HAS_ETH1 447 #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD 448 #define CONFIG_HAS_ETH2 449 #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD 450 #endif 451 452 #define CONFIG_IPADDR 192.168.1.253 453 454 #define CONFIG_HOSTNAME unknown 455 #define CONFIG_ROOTPATH /nfsroot 456 #define CONFIG_BOOTFILE your.uImage 457 458 #define CONFIG_SERVERIP 192.168.1.1 459 #define CONFIG_GATEWAYIP 192.168.1.1 460 #define CONFIG_NETMASK 255.255.255.0 461 462 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ 463 464 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 465 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 466 467 #define CONFIG_BAUDRATE 115200 468 469 #define CONFIG_EXTRA_ENV_SETTINGS \ 470 "netdev=eth0\0" \ 471 "consoledev=ttyS0\0" \ 472 "ramdiskaddr=1000000\0" \ 473 "ramdiskfile=your.ramdisk.u-boot\0" \ 474 "fdtaddr=400000\0" \ 475 "fdtfile=your.fdt.dtb\0" 476 477 #define CONFIG_NFSBOOTCOMMAND \ 478 "setenv bootargs root=/dev/nfs rw " \ 479 "nfsroot=$serverip:$rootpath " \ 480 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 481 "console=$consoledev,$baudrate $othbootargs;" \ 482 "tftp $loadaddr $bootfile;" \ 483 "tftp $fdtaddr $fdtfile;" \ 484 "bootm $loadaddr - $fdtaddr" 485 486 #define CONFIG_RAMBOOTCOMMAND \ 487 "setenv bootargs root=/dev/ram rw " \ 488 "console=$consoledev,$baudrate $othbootargs;" \ 489 "tftp $ramdiskaddr $ramdiskfile;" \ 490 "tftp $loadaddr $bootfile;" \ 491 "tftp $fdtaddr $fdtfile;" \ 492 "bootm $loadaddr $ramdiskaddr $fdtaddr" 493 494 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 495 496 #endif /* __CONFIG_H */ 497