1 /* 2 * Copyright 2007-2009,2010-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * mpc8536ds board configuration file 9 * 10 */ 11 #ifndef __CONFIG_H 12 #define __CONFIG_H 13 14 #include "../board/freescale/common/ics307_clk.h" 15 16 #ifdef CONFIG_36BIT 17 #define CONFIG_PHYS_64BIT 1 18 #endif 19 20 #ifdef CONFIG_NAND 21 #define CONFIG_NAND_U_BOOT 1 22 #define CONFIG_RAMBOOT_NAND 1 23 #ifdef CONFIG_NAND_SPL 24 #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 25 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ 26 #else 27 #define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds 28 #define CONFIG_SYS_TEXT_BASE 0xf8f82000 29 #endif /* CONFIG_NAND_SPL */ 30 #endif 31 32 #ifdef CONFIG_SDCARD 33 #define CONFIG_RAMBOOT_SDCARD 1 34 #define CONFIG_SYS_TEXT_BASE 0xf8f80000 35 #define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc 36 #endif 37 38 #ifdef CONFIG_SPIFLASH 39 #define CONFIG_RAMBOOT_SPIFLASH 1 40 #define CONFIG_SYS_TEXT_BASE 0xf8f80000 41 #define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc 42 #endif 43 44 #ifndef CONFIG_SYS_TEXT_BASE 45 #define CONFIG_SYS_TEXT_BASE 0xeff40000 46 #endif 47 48 #ifndef CONFIG_RESET_VECTOR_ADDRESS 49 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 50 #endif 51 52 #ifndef CONFIG_SYS_MONITOR_BASE 53 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 54 #endif 55 56 /* High Level Configuration Options */ 57 #define CONFIG_BOOKE 1 /* BOOKE */ 58 #define CONFIG_E500 1 /* BOOKE e500 family */ 59 #define CONFIG_MPC8536 1 60 #define CONFIG_MPC8536DS 1 61 62 #define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */ 63 #define CONFIG_SPI_FLASH 1 /* Has SPI Flash */ 64 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 65 #define CONFIG_PCI1 1 /* Enable PCI controller 1 */ 66 #define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ 67 #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ 68 #define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ 69 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 70 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 71 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 72 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 73 74 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 75 #define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/ 76 77 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 78 #define CONFIG_ENV_OVERWRITE 79 80 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ 81 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 82 #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ 83 84 /* 85 * These can be toggled for performance analysis, otherwise use default. 86 */ 87 #define CONFIG_L2_CACHE /* toggle L2 cache */ 88 #define CONFIG_BTB /* toggle branch predition */ 89 90 #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ 91 92 #define CONFIG_ENABLE_36BIT_PHYS 1 93 94 #ifdef CONFIG_PHYS_64BIT 95 #define CONFIG_ADDR_MAP 1 96 #define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ 97 #endif 98 99 #define CONFIG_SYS_MEMTEST_START 0x00010000 /* skip exception vectors */ 100 #define CONFIG_SYS_MEMTEST_END 0x1f000000 /* skip u-boot at top of RAM */ 101 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 102 103 /* 104 * Config the L2 Cache as L2 SRAM 105 */ 106 #define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 107 #ifdef CONFIG_PHYS_64BIT 108 #define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull 109 #else 110 #define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR 111 #endif 112 #define CONFIG_SYS_L2_SIZE (512 << 10) 113 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) 114 115 #define CONFIG_SYS_CCSRBAR 0xffe00000 116 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 117 118 #if defined(CONFIG_NAND_SPL) 119 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 120 #endif 121 122 /* DDR Setup */ 123 #define CONFIG_VERY_BIG_RAM 124 #define CONFIG_SYS_FSL_DDR2 125 #undef CONFIG_FSL_DDR_INTERACTIVE 126 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 127 #define CONFIG_DDR_SPD 128 129 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 130 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 131 132 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 133 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 134 135 #define CONFIG_NUM_DDR_CONTROLLERS 1 136 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 137 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 138 139 /* I2C addresses of SPD EEPROMs */ 140 #define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ 141 #define CONFIG_SYS_SPD_BUS_NUM 1 142 143 /* These are used when DDR doesn't use SPD. */ 144 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 145 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F 146 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 147 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 148 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 149 #define CONFIG_SYS_DDR_TIMING_1 0x3935d322 150 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 151 #define CONFIG_SYS_DDR_MODE_1 0x00480432 152 #define CONFIG_SYS_DDR_MODE_2 0x00000000 153 #define CONFIG_SYS_DDR_INTERVAL 0x06180100 154 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 155 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 156 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 157 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 158 #define CONFIG_SYS_DDR_CONTROL 0xC3008000 /* Type = DDR2 */ 159 #define CONFIG_SYS_DDR_CONTROL2 0x04400010 160 161 #define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d 162 #define CONFIG_SYS_DDR_ERR_DIS 0x00000000 163 #define CONFIG_SYS_DDR_SBE 0x00010000 164 165 /* Make sure required options are set */ 166 #ifndef CONFIG_SPD_EEPROM 167 #error ("CONFIG_SPD_EEPROM is required") 168 #endif 169 170 #undef CONFIG_CLOCKS_IN_MHZ 171 172 173 /* 174 * Memory map -- xxx -this is wrong, needs updating 175 * 176 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 177 * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable 178 * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable 179 * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable 180 * 181 * Localbus cacheable (TBD) 182 * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable 183 * 184 * Localbus non-cacheable 185 * 0xe000_0000 0xe7ff_ffff Promjet/free 128M non-cacheable 186 * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable 187 * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable 188 * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 189 * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 190 * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable 191 */ 192 193 /* 194 * Local Bus Definitions 195 */ 196 #define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ 197 #ifdef CONFIG_PHYS_64BIT 198 #define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull 199 #else 200 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 201 #endif 202 203 #define CONFIG_FLASH_BR_PRELIM \ 204 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V) 205 #define CONFIG_FLASH_OR_PRELIM 0xf8000ff7 206 207 #define CONFIG_SYS_BR1_PRELIM \ 208 (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 209 | BR_PS_16 | BR_V) 210 #define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 211 212 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, \ 213 CONFIG_SYS_FLASH_BASE_PHYS } 214 #define CONFIG_SYS_FLASH_QUIET_TEST 215 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 216 217 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 218 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 219 #undef CONFIG_SYS_FLASH_CHECKSUM 220 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 221 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 222 223 #if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \ 224 defined(CONFIG_RAMBOOT_SPIFLASH) 225 #define CONFIG_SYS_RAMBOOT 226 #define CONFIG_SYS_EXTRA_ENV_RELOC 227 #else 228 #undef CONFIG_SYS_RAMBOOT 229 #endif 230 231 #define CONFIG_FLASH_CFI_DRIVER 232 #define CONFIG_SYS_FLASH_CFI 233 #define CONFIG_SYS_FLASH_EMPTY_INFO 234 #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 235 236 #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ 237 238 #define CONFIG_HWCONFIG /* enable hwconfig */ 239 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 240 #define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ 241 #ifdef CONFIG_PHYS_64BIT 242 #define PIXIS_BASE_PHYS 0xfffdf0000ull 243 #else 244 #define PIXIS_BASE_PHYS PIXIS_BASE 245 #endif 246 247 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) 248 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ 249 250 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 251 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 252 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 253 #define PIXIS_CSR 0x3 /* PIXIS General control/status register */ 254 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 255 #define PIXIS_PWR 0x5 /* PIXIS Power status register */ 256 #define PIXIS_AUX 0x6 /* Auxiliary 1 register */ 257 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 258 #define PIXIS_AUX2 0x8 /* Auxiliary 2 register */ 259 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 260 #define PIXIS_VSTAT 0x11 /* VELA Status Register */ 261 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 262 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 263 #define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */ 264 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 265 #define PIXIS_VBOOT_LBMAP 0xe0 /* VBOOT - CFG_LBMAP */ 266 #define PIXIS_VBOOT_LBMAP_NOR0 0x00 /* cfg_lbmap - boot from NOR 0 */ 267 #define PIXIS_VBOOT_LBMAP_NOR1 0x01 /* cfg_lbmap - boot from NOR 1 */ 268 #define PIXIS_VBOOT_LBMAP_NOR2 0x02 /* cfg_lbmap - boot from NOR 2 */ 269 #define PIXIS_VBOOT_LBMAP_NOR3 0x03 /* cfg_lbmap - boot from NOR 3 */ 270 #define PIXIS_VBOOT_LBMAP_PJET 0x04 /* cfg_lbmap - boot from projet */ 271 #define PIXIS_VBOOT_LBMAP_NAND 0x05 /* cfg_lbmap - boot from NAND */ 272 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 273 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 274 #define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */ 275 #define PIXIS_VSYSCLK0 0x1A /* VELA SYSCLK0 Register */ 276 #define PIXIS_VSYSCLK1 0x1B /* VELA SYSCLK1 Register */ 277 #define PIXIS_VSYSCLK2 0x1C /* VELA SYSCLK2 Register */ 278 #define PIXIS_VDDRCLK0 0x1D /* VELA DDRCLK0 Register */ 279 #define PIXIS_VDDRCLK1 0x1E /* VELA DDRCLK1 Register */ 280 #define PIXIS_VDDRCLK2 0x1F /* VELA DDRCLK2 Register */ 281 #define PIXIS_VWATCH 0x24 /* Watchdog Register */ 282 #define PIXIS_LED 0x25 /* LED Register */ 283 284 #define PIXIS_SPD_SYSCLK 0x7 /* SYSCLK option */ 285 286 /* old pixis referenced names */ 287 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 288 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 289 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x4e 290 291 #define CONFIG_SYS_INIT_RAM_LOCK 1 292 #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ 293 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ 294 295 #define CONFIG_SYS_GBL_DATA_OFFSET \ 296 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 297 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 298 299 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 300 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 301 302 #ifndef CONFIG_NAND_SPL 303 #define CONFIG_SYS_NAND_BASE 0xffa00000 304 #ifdef CONFIG_PHYS_64BIT 305 #define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull 306 #else 307 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 308 #endif 309 #else 310 #define CONFIG_SYS_NAND_BASE 0xfff00000 311 #ifdef CONFIG_PHYS_64BIT 312 #define CONFIG_SYS_NAND_BASE_PHYS 0xffff00000ull 313 #else 314 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 315 #endif 316 #endif 317 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ 318 CONFIG_SYS_NAND_BASE + 0x40000, \ 319 CONFIG_SYS_NAND_BASE + 0x80000, \ 320 CONFIG_SYS_NAND_BASE + 0xC0000} 321 #define CONFIG_SYS_MAX_NAND_DEVICE 4 322 #define CONFIG_MTD_NAND_VERIFY_WRITE 323 #define CONFIG_CMD_NAND 1 324 #define CONFIG_NAND_FSL_ELBC 1 325 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 326 327 /* NAND boot: 4K NAND loader config */ 328 #define CONFIG_SYS_NAND_SPL_SIZE 0x1000 329 #define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000) 330 #define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) 331 #define CONFIG_SYS_NAND_U_BOOT_START \ 332 (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE) 333 #define CONFIG_SYS_NAND_U_BOOT_OFFS (0) 334 #define CONFIG_SYS_NAND_U_BOOT_RELOC (CONFIG_SYS_INIT_L2_END - 0x2000) 335 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) 336 337 /* NAND flash config */ 338 #define CONFIG_SYS_NAND_BR_PRELIM \ 339 (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 340 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 341 | BR_PS_8 /* Port Size = 8 bit */ \ 342 | BR_MS_FCM /* MSEL = FCM */ \ 343 | BR_V) /* valid */ 344 #define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ 345 | OR_FCM_PGS /* Large Page*/ \ 346 | OR_FCM_CSCT \ 347 | OR_FCM_CST \ 348 | OR_FCM_CHT \ 349 | OR_FCM_SCY_1 \ 350 | OR_FCM_TRLX \ 351 | OR_FCM_EHTR) 352 353 #ifdef CONFIG_RAMBOOT_NAND 354 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 355 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 356 #define CONFIG_SYS_BR2_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 357 #define CONFIG_SYS_OR2_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 358 #else 359 #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ 360 #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ 361 #define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ 362 #define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 363 #endif 364 365 #define CONFIG_SYS_BR4_PRELIM \ 366 (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \ 367 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 368 | BR_PS_8 /* Port Size = 8 bit */ \ 369 | BR_MS_FCM /* MSEL = FCM */ \ 370 | BR_V) /* valid */ 371 #define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 372 #define CONFIG_SYS_BR5_PRELIM \ 373 (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \ 374 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 375 | BR_PS_8 /* Port Size = 8 bit */ \ 376 | BR_MS_FCM /* MSEL = FCM */ \ 377 | BR_V) /* valid */ 378 #define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 379 380 #define CONFIG_SYS_BR6_PRELIM \ 381 (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \ 382 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 383 | BR_PS_8 /* Port Size = 8 bit */ \ 384 | BR_MS_FCM /* MSEL = FCM */ \ 385 | BR_V) /* valid */ 386 #define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ 387 388 /* Serial Port - controlled on board with jumper J8 389 * open - index 2 390 * shorted - index 1 391 */ 392 #define CONFIG_CONS_INDEX 1 393 #define CONFIG_SYS_NS16550 394 #define CONFIG_SYS_NS16550_SERIAL 395 #define CONFIG_SYS_NS16550_REG_SIZE 1 396 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 397 #ifdef CONFIG_NAND_SPL 398 #define CONFIG_NS16550_MIN_FUNCTIONS 399 #endif 400 401 #define CONFIG_SYS_BAUDRATE_TABLE \ 402 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 403 404 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) 405 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) 406 407 /* Use the HUSH parser */ 408 #define CONFIG_SYS_HUSH_PARSER 409 410 /* 411 * Pass open firmware flat tree 412 */ 413 #define CONFIG_OF_LIBFDT 1 414 #define CONFIG_OF_BOARD_SETUP 1 415 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 416 417 /* 418 * I2C 419 */ 420 #define CONFIG_SYS_I2C 421 #define CONFIG_SYS_I2C_FSL 422 #define CONFIG_SYS_FSL_I2C_SPEED 400000 423 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 424 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 425 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 426 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 427 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 428 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } 429 430 /* 431 * I2C2 EEPROM 432 */ 433 #define CONFIG_ID_EEPROM 434 #ifdef CONFIG_ID_EEPROM 435 #define CONFIG_SYS_I2C_EEPROM_NXID 436 #endif 437 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 438 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 439 #define CONFIG_SYS_EEPROM_BUS_NUM 1 440 441 /* 442 * eSPI - Enhanced SPI 443 */ 444 #define CONFIG_HARD_SPI 445 #define CONFIG_FSL_ESPI 446 447 #if defined(CONFIG_SPI_FLASH) 448 #define CONFIG_SPI_FLASH_SPANSION 449 #define CONFIG_CMD_SF 450 #define CONFIG_SF_DEFAULT_SPEED 10000000 451 #define CONFIG_SF_DEFAULT_MODE 0 452 #endif 453 454 /* 455 * General PCI 456 * Memory space is mapped 1-1, but I/O space must start from 0. 457 */ 458 459 #define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 460 #ifdef CONFIG_PHYS_64BIT 461 #define CONFIG_SYS_PCI1_MEM_BUS 0xf0000000 462 #define CONFIG_SYS_PCI1_MEM_PHYS 0xc00000000ull 463 #else 464 #define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 465 #define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 466 #endif 467 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 468 #define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000 469 #define CONFIG_SYS_PCI1_IO_BUS 0x00000000 470 #ifdef CONFIG_PHYS_64BIT 471 #define CONFIG_SYS_PCI1_IO_PHYS 0xfffc00000ull 472 #else 473 #define CONFIG_SYS_PCI1_IO_PHYS 0xffc00000 474 #endif 475 #define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64k */ 476 477 /* controller 1, Slot 1, tgtid 1, Base address a000 */ 478 #define CONFIG_SYS_PCIE1_NAME "Slot 1" 479 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x90000000 480 #ifdef CONFIG_PHYS_64BIT 481 #define CONFIG_SYS_PCIE1_MEM_BUS 0xf8000000 482 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc10000000ull 483 #else 484 #define CONFIG_SYS_PCIE1_MEM_BUS 0x90000000 485 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x90000000 486 #endif 487 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x08000000 /* 128M */ 488 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc10000 489 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 490 #ifdef CONFIG_PHYS_64BIT 491 #define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc10000ull 492 #else 493 #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc10000 494 #endif 495 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 496 497 /* controller 2, Slot 2, tgtid 2, Base address 9000 */ 498 #define CONFIG_SYS_PCIE2_NAME "Slot 2" 499 #define CONFIG_SYS_PCIE2_MEM_VIRT 0x98000000 500 #ifdef CONFIG_PHYS_64BIT 501 #define CONFIG_SYS_PCIE2_MEM_BUS 0xf8000000 502 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xc18000000ull 503 #else 504 #define CONFIG_SYS_PCIE2_MEM_BUS 0x98000000 505 #define CONFIG_SYS_PCIE2_MEM_PHYS 0x98000000 506 #endif 507 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x08000000 /* 128M */ 508 #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000 509 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 510 #ifdef CONFIG_PHYS_64BIT 511 #define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc20000ull 512 #else 513 #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000 514 #endif 515 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ 516 517 /* controller 3, direct to uli, tgtid 3, Base address 8000 */ 518 #define CONFIG_SYS_PCIE3_NAME "Slot 3" 519 #define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 520 #ifdef CONFIG_PHYS_64BIT 521 #define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 522 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull 523 #else 524 #define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000 525 #define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000 526 #endif 527 #define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ 528 #define CONFIG_SYS_PCIE3_IO_VIRT 0xffc30000 529 #define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 530 #ifdef CONFIG_PHYS_64BIT 531 #define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc30000ull 532 #else 533 #define CONFIG_SYS_PCIE3_IO_PHYS 0xffc30000 534 #endif 535 #define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ 536 537 #if defined(CONFIG_PCI) 538 539 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 540 541 /*PCIE video card used*/ 542 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE3_IO_VIRT 543 544 /*PCI video card used*/ 545 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/ 546 547 /* video */ 548 #define CONFIG_VIDEO 549 550 #if defined(CONFIG_VIDEO) 551 #define CONFIG_BIOSEMU 552 #define CONFIG_CFB_CONSOLE 553 #define CONFIG_VIDEO_SW_CURSOR 554 #define CONFIG_VGA_AS_SINGLE_DEVICE 555 #define CONFIG_ATI_RADEON_FB 556 #define CONFIG_VIDEO_LOGO 557 /*#define CONFIG_CONSOLE_CURSOR*/ 558 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE3_IO_VIRT 559 #endif 560 561 #undef CONFIG_EEPRO100 562 #undef CONFIG_TULIP 563 #undef CONFIG_RTL8139 564 565 #ifndef CONFIG_PCI_PNP 566 #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BUS 567 #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_IO_BUS 568 #define PCI_IDSEL_NUMBER 0x11 /* IDSEL = AD11 */ 569 #endif 570 571 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 572 573 #endif /* CONFIG_PCI */ 574 575 /* SATA */ 576 #define CONFIG_LIBATA 577 #define CONFIG_FSL_SATA 578 579 #define CONFIG_SYS_SATA_MAX_DEVICE 2 580 #define CONFIG_SATA1 581 #define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR 582 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 583 #define CONFIG_SATA2 584 #define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR 585 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 586 587 #ifdef CONFIG_FSL_SATA 588 #define CONFIG_LBA48 589 #define CONFIG_CMD_SATA 590 #define CONFIG_DOS_PARTITION 591 #define CONFIG_CMD_EXT2 592 #endif 593 594 #if defined(CONFIG_TSEC_ENET) 595 596 #define CONFIG_MII 1 /* MII PHY management */ 597 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 598 #define CONFIG_TSEC1 1 599 #define CONFIG_TSEC1_NAME "eTSEC1" 600 #define CONFIG_TSEC3 1 601 #define CONFIG_TSEC3_NAME "eTSEC3" 602 603 #define CONFIG_FSL_SGMII_RISER 1 604 #define SGMII_RISER_PHY_OFFSET 0x1c 605 606 #define TSEC1_PHY_ADDR 1 /* TSEC1 -> PHY1 */ 607 #define TSEC3_PHY_ADDR 0 /* TSEC3 -> PHY0 */ 608 609 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 610 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 611 612 #define TSEC1_PHYIDX 0 613 #define TSEC3_PHYIDX 0 614 615 #define CONFIG_ETHPRIME "eTSEC1" 616 617 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 618 619 #endif /* CONFIG_TSEC_ENET */ 620 621 /* 622 * Environment 623 */ 624 625 #if defined(CONFIG_SYS_RAMBOOT) 626 #if defined(CONFIG_RAMBOOT_NAND) 627 #define CONFIG_ENV_IS_IN_NAND 1 628 #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 629 #define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) 630 #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) 631 #elif defined(CONFIG_RAMBOOT_SPIFLASH) 632 #define CONFIG_ENV_IS_IN_SPI_FLASH 633 #define CONFIG_ENV_SPI_BUS 0 634 #define CONFIG_ENV_SPI_CS 0 635 #define CONFIG_ENV_SPI_MAX_HZ 10000000 636 #define CONFIG_ENV_SPI_MODE 0 637 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 638 #define CONFIG_ENV_OFFSET 0xF0000 639 #define CONFIG_ENV_SECT_SIZE 0x10000 640 #elif defined(CONFIG_RAMBOOT_SDCARD) 641 #define CONFIG_ENV_IS_IN_MMC 642 #define CONFIG_FSL_FIXED_MMC_LOCATION 643 #define CONFIG_ENV_SIZE 0x2000 644 #define CONFIG_SYS_MMC_ENV_DEV 0 645 #else 646 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 647 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 648 #define CONFIG_ENV_SIZE 0x2000 649 #endif 650 #else 651 #define CONFIG_ENV_IS_IN_FLASH 1 652 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 653 #define CONFIG_ENV_SIZE 0x2000 654 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 655 #endif 656 657 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 658 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 659 660 /* 661 * Command line configuration. 662 */ 663 #include <config_cmd_default.h> 664 665 #define CONFIG_CMD_IRQ 666 #define CONFIG_CMD_PING 667 #define CONFIG_CMD_I2C 668 #define CONFIG_CMD_MII 669 #define CONFIG_CMD_ELF 670 #define CONFIG_CMD_IRQ 671 #define CONFIG_CMD_SETEXPR 672 #define CONFIG_CMD_REGINFO 673 674 #if defined(CONFIG_PCI) 675 #define CONFIG_CMD_PCI 676 #define CONFIG_CMD_NET 677 #endif 678 679 #undef CONFIG_WATCHDOG /* watchdog disabled */ 680 681 #define CONFIG_MMC 1 682 683 #ifdef CONFIG_MMC 684 #define CONFIG_FSL_ESDHC 685 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR 686 #define CONFIG_CMD_MMC 687 #define CONFIG_GENERIC_MMC 688 #endif 689 690 /* 691 * USB 692 */ 693 #define CONFIG_HAS_FSL_MPH_USB 694 #ifdef CONFIG_HAS_FSL_MPH_USB 695 #define CONFIG_USB_EHCI 696 697 #ifdef CONFIG_USB_EHCI 698 #define CONFIG_CMD_USB 699 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 700 #define CONFIG_USB_EHCI_FSL 701 #define CONFIG_USB_STORAGE 702 #endif 703 #endif 704 705 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) 706 #define CONFIG_CMD_EXT2 707 #define CONFIG_CMD_FAT 708 #define CONFIG_DOS_PARTITION 709 #endif 710 711 /* 712 * Miscellaneous configurable options 713 */ 714 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 715 #define CONFIG_CMDLINE_EDITING /* Command-line editing */ 716 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 717 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 718 #if defined(CONFIG_CMD_KGDB) 719 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 720 #else 721 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 722 #endif 723 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ 724 + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */ 725 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 726 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 727 728 /* 729 * For booting Linux, the board info and command line data 730 * have to be in the first 64 MB of memory, since this is 731 * the maximum mapped by the Linux kernel during initialization. 732 */ 733 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */ 734 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 735 736 #if defined(CONFIG_CMD_KGDB) 737 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 738 #endif 739 740 /* 741 * Environment Configuration 742 */ 743 744 /* The mac addresses for all ethernet interface */ 745 #if defined(CONFIG_TSEC_ENET) 746 #define CONFIG_HAS_ETH0 747 #define CONFIG_ETHADDR 00:E0:0C:02:00:FD 748 #define CONFIG_HAS_ETH1 749 #define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD 750 #define CONFIG_HAS_ETH2 751 #define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD 752 #define CONFIG_HAS_ETH3 753 #define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD 754 #endif 755 756 #define CONFIG_IPADDR 192.168.1.254 757 758 #define CONFIG_HOSTNAME unknown 759 #define CONFIG_ROOTPATH "/opt/nfsroot" 760 #define CONFIG_BOOTFILE "uImage" 761 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 762 763 #define CONFIG_SERVERIP 192.168.1.1 764 #define CONFIG_GATEWAYIP 192.168.1.1 765 #define CONFIG_NETMASK 255.255.255.0 766 767 /* default location for tftp and bootm */ 768 #define CONFIG_LOADADDR 1000000 769 770 #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ 771 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 772 773 #define CONFIG_BAUDRATE 115200 774 775 #define CONFIG_EXTRA_ENV_SETTINGS \ 776 "netdev=eth0\0" \ 777 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 778 "tftpflash=tftpboot $loadaddr $uboot; " \ 779 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 780 " +$filesize; " \ 781 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 782 " +$filesize; " \ 783 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 784 " $filesize; " \ 785 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 786 " +$filesize; " \ 787 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 788 " $filesize\0" \ 789 "consoledev=ttyS0\0" \ 790 "ramdiskaddr=2000000\0" \ 791 "ramdiskfile=8536ds/ramdisk.uboot\0" \ 792 "fdtaddr=c00000\0" \ 793 "fdtfile=8536ds/mpc8536ds.dtb\0" \ 794 "bdev=sda3\0" \ 795 "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" 796 797 #define CONFIG_HDBOOT \ 798 "setenv bootargs root=/dev/$bdev rw " \ 799 "console=$consoledev,$baudrate $othbootargs;" \ 800 "tftp $loadaddr $bootfile;" \ 801 "tftp $fdtaddr $fdtfile;" \ 802 "bootm $loadaddr - $fdtaddr" 803 804 #define CONFIG_NFSBOOTCOMMAND \ 805 "setenv bootargs root=/dev/nfs rw " \ 806 "nfsroot=$serverip:$rootpath " \ 807 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 808 "console=$consoledev,$baudrate $othbootargs;" \ 809 "tftp $loadaddr $bootfile;" \ 810 "tftp $fdtaddr $fdtfile;" \ 811 "bootm $loadaddr - $fdtaddr" 812 813 #define CONFIG_RAMBOOTCOMMAND \ 814 "setenv bootargs root=/dev/ram rw " \ 815 "console=$consoledev,$baudrate $othbootargs;" \ 816 "tftp $ramdiskaddr $ramdiskfile;" \ 817 "tftp $loadaddr $bootfile;" \ 818 "tftp $fdtaddr $fdtfile;" \ 819 "bootm $loadaddr $ramdiskaddr $fdtaddr" 820 821 #define CONFIG_BOOTCOMMAND CONFIG_HDBOOT 822 823 #endif /* __CONFIG_H */ 824