1 /* 2 * Copyright (C) 2007 Freescale Semiconductor, Inc. 3 * Dave Liu <daveliu@freescale.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 /* 12 * High Level Configuration Options 13 */ 14 #define CONFIG_E300 1 /* E300 family */ 15 #define CONFIG_MPC837x 1 /* MPC837x CPU specific */ 16 #define CONFIG_MPC837XEMDS 1 /* MPC837XEMDS board specific */ 17 18 #define CONFIG_SYS_TEXT_BASE 0xFE000000 19 20 /* 21 * System Clock Setup 22 */ 23 #ifdef CONFIG_PCISLAVE 24 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 25 #else 26 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 27 #endif 28 29 #ifndef CONFIG_SYS_CLK_FREQ 30 #define CONFIG_SYS_CLK_FREQ 66000000 31 #endif 32 33 /* 34 * Hardware Reset Configuration Word 35 * if CLKIN is 66MHz, then 36 * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz 37 */ 38 #define CONFIG_SYS_HRCW_LOW (\ 39 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 40 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 41 HRCWL_SVCOD_DIV_2 |\ 42 HRCWL_CSB_TO_CLKIN_6X1 |\ 43 HRCWL_CORE_TO_CSB_1_5X1) 44 45 #ifdef CONFIG_PCISLAVE 46 #define CONFIG_SYS_HRCW_HIGH (\ 47 HRCWH_PCI_AGENT |\ 48 HRCWH_PCI1_ARBITER_DISABLE |\ 49 HRCWH_CORE_ENABLE |\ 50 HRCWH_FROM_0XFFF00100 |\ 51 HRCWH_BOOTSEQ_DISABLE |\ 52 HRCWH_SW_WATCHDOG_DISABLE |\ 53 HRCWH_ROM_LOC_LOCAL_16BIT |\ 54 HRCWH_RL_EXT_LEGACY |\ 55 HRCWH_TSEC1M_IN_RGMII |\ 56 HRCWH_TSEC2M_IN_RGMII |\ 57 HRCWH_BIG_ENDIAN |\ 58 HRCWH_LDP_CLEAR) 59 #else 60 #define CONFIG_SYS_HRCW_HIGH (\ 61 HRCWH_PCI_HOST |\ 62 HRCWH_PCI1_ARBITER_ENABLE |\ 63 HRCWH_CORE_ENABLE |\ 64 HRCWH_FROM_0X00000100 |\ 65 HRCWH_BOOTSEQ_DISABLE |\ 66 HRCWH_SW_WATCHDOG_DISABLE |\ 67 HRCWH_ROM_LOC_LOCAL_16BIT |\ 68 HRCWH_RL_EXT_LEGACY |\ 69 HRCWH_TSEC1M_IN_RGMII |\ 70 HRCWH_TSEC2M_IN_RGMII |\ 71 HRCWH_BIG_ENDIAN |\ 72 HRCWH_LDP_CLEAR) 73 #endif 74 75 /* Arbiter Configuration Register */ 76 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 77 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 78 79 /* System Priority Control Register */ 80 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC1/2 emergency has highest priority */ 81 82 /* 83 * IP blocks clock configuration 84 */ 85 #define CONFIG_SYS_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ 86 #define CONFIG_SYS_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ 87 #define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* CSB:SATA[0:3] = 2:1 */ 88 89 /* 90 * System IO Config 91 */ 92 #define CONFIG_SYS_SICRH 0x00000000 93 #define CONFIG_SYS_SICRL 0x00000000 94 95 /* 96 * Output Buffer Impedance 97 */ 98 #define CONFIG_SYS_OBIR 0x31100000 99 100 #define CONFIG_BOARD_EARLY_INIT_R 101 #define CONFIG_HWCONFIG 102 103 /* 104 * IMMR new address 105 */ 106 #define CONFIG_SYS_IMMR 0xE0000000 107 108 /* 109 * DDR Setup 110 */ 111 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 112 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 113 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 114 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 115 #define CONFIG_SYS_83XX_DDR_USES_CS0 116 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \ 117 | DDRCDR_ODT \ 118 | DDRCDR_Q_DRN) 119 /* 0x80080001 */ /* ODT 150ohm on SoC */ 120 121 #undef CONFIG_DDR_ECC /* support DDR ECC function */ 122 #undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ 123 124 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 125 #define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ 126 127 #if defined(CONFIG_SPD_EEPROM) 128 #define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ 129 #else 130 /* 131 * Manually set up DDR parameters 132 * WHITE ELECTRONIC DESIGNS - W3HG64M72EEU403PD4 SO-DIMM 133 * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 134 */ 135 #define CONFIG_SYS_DDR_SIZE 512 /* MB */ 136 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000001f 137 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 138 | CSCONFIG_ODT_RD_NEVER /* ODT_RD to none */ \ 139 | CSCONFIG_ODT_WR_ONLY_CURRENT /* ODT_WR to CSn */ \ 140 | CSCONFIG_ROW_BIT_14 \ 141 | CSCONFIG_COL_BIT_10) 142 /* 0x80010202 */ 143 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 144 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 145 | (0 << TIMING_CFG0_WRT_SHIFT) \ 146 | (0 << TIMING_CFG0_RRT_SHIFT) \ 147 | (0 << TIMING_CFG0_WWT_SHIFT) \ 148 | (6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 149 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 150 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 151 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 152 /* 0x00620802 */ 153 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ 154 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 155 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ 156 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 157 | (13 << TIMING_CFG1_REFREC_SHIFT) \ 158 | (3 << TIMING_CFG1_WRREC_SHIFT) \ 159 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 160 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 161 /* 0x3935d322 */ 162 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 163 | (6 << TIMING_CFG2_CPO_SHIFT) \ 164 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 165 | (4 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 166 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 167 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 168 | (8 << TIMING_CFG2_FOUR_ACT_SHIFT)) 169 /* 0x131088c8 */ 170 #define CONFIG_SYS_DDR_INTERVAL ((0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT) \ 171 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 172 /* 0x03E00100 */ 173 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 174 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ 175 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 176 | (0x1432 << SDRAM_MODE_SD_SHIFT)) 177 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 178 #define CONFIG_SYS_DDR_MODE2 0x00000000 179 #endif 180 181 /* 182 * Memory test 183 */ 184 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 185 #define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ 186 #define CONFIG_SYS_MEMTEST_END 0x00140000 187 188 /* 189 * The reserved memory 190 */ 191 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 192 193 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 194 #define CONFIG_SYS_RAMBOOT 195 #else 196 #undef CONFIG_SYS_RAMBOOT 197 #endif 198 199 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 200 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 201 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 202 203 /* 204 * Initial RAM Base Address Setup 205 */ 206 #define CONFIG_SYS_INIT_RAM_LOCK 1 207 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 208 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 209 #define CONFIG_SYS_GBL_DATA_OFFSET \ 210 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 211 212 /* 213 * Local Bus Configuration & Clock Setup 214 */ 215 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 216 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 217 #define CONFIG_SYS_LBC_LBCR 0x00000000 218 #define CONFIG_FSL_ELBC 1 219 220 /* 221 * FLASH on the Local Bus 222 */ 223 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 224 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 225 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 226 #define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */ 227 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 228 229 /* Window base at flash base */ 230 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 231 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 232 233 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 234 | BR_PS_16 /* 16 bit port */ \ 235 | BR_MS_GPCM /* MSEL = GPCM */ \ 236 | BR_V) /* valid */ 237 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 238 | OR_UPM_XAM \ 239 | OR_GPCM_CSNT \ 240 | OR_GPCM_ACS_DIV2 \ 241 | OR_GPCM_XACS \ 242 | OR_GPCM_SCY_15 \ 243 | OR_GPCM_TRLX_SET \ 244 | OR_GPCM_EHTR_SET \ 245 | OR_GPCM_EAD) 246 /* 0xFE000FF7 */ 247 248 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 249 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ 250 251 #undef CONFIG_SYS_FLASH_CHECKSUM 252 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 253 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 254 255 /* 256 * BCSR on the Local Bus 257 */ 258 #define CONFIG_SYS_BCSR 0xF8000000 259 /* Access window base at BCSR base */ 260 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 261 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 262 263 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 264 | BR_PS_8 \ 265 | BR_MS_GPCM \ 266 | BR_V) 267 /* 0xF8000801 */ 268 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 269 | OR_GPCM_XAM \ 270 | OR_GPCM_CSNT \ 271 | OR_GPCM_XACS \ 272 | OR_GPCM_SCY_15 \ 273 | OR_GPCM_TRLX_SET \ 274 | OR_GPCM_EHTR_SET \ 275 | OR_GPCM_EAD) 276 /* 0xFFFFE9F7 */ 277 278 /* 279 * NAND Flash on the Local Bus 280 */ 281 #define CONFIG_SYS_MAX_NAND_DEVICE 1 282 #define CONFIG_NAND_FSL_ELBC 1 283 284 #define CONFIG_SYS_NAND_BASE 0xE0600000 285 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE \ 286 | BR_DECC_CHK_GEN /* Use HW ECC */ \ 287 | BR_PS_8 /* 8 bit port */ \ 288 | BR_MS_FCM /* MSEL = FCM */ \ 289 | BR_V) /* valid */ 290 #define CONFIG_SYS_OR3_PRELIM (OR_AM_32KB \ 291 | OR_FCM_BCTLD \ 292 | OR_FCM_CST \ 293 | OR_FCM_CHT \ 294 | OR_FCM_SCY_1 \ 295 | OR_FCM_RST \ 296 | OR_FCM_TRLX \ 297 | OR_FCM_EHTR) 298 /* 0xFFFF919E */ 299 300 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_NAND_BASE 301 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 302 303 /* 304 * Serial Port 305 */ 306 #define CONFIG_CONS_INDEX 1 307 #define CONFIG_SYS_NS16550_SERIAL 308 #define CONFIG_SYS_NS16550_REG_SIZE 1 309 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 310 311 #define CONFIG_SYS_BAUDRATE_TABLE \ 312 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 313 314 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 315 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 316 317 /* I2C */ 318 #define CONFIG_SYS_I2C 319 #define CONFIG_SYS_I2C_FSL 320 #define CONFIG_SYS_FSL_I2C_SPEED 400000 321 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 322 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 323 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } 324 325 /* 326 * Config on-board RTC 327 */ 328 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 329 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 330 331 /* 332 * General PCI 333 * Addresses are mapped 1-1. 334 */ 335 #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 336 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE 337 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ 338 #define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 339 #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE 340 #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ 341 #define CONFIG_SYS_PCI_IO_BASE 0x00000000 342 #define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 343 #define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ 344 345 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 346 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 347 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 348 349 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 350 #define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000 351 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000 352 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000 353 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000 354 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 355 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 356 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000 357 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 358 359 #define CONFIG_SYS_PCIE2_BASE 0xC0000000 360 #define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000 361 #define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000 362 #define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000 363 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000 364 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 365 #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 366 #define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000 367 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 368 369 #ifdef CONFIG_PCI 370 #define CONFIG_PCI_INDIRECT_BRIDGE 371 #ifndef __ASSEMBLY__ 372 extern int board_pci_host_broken(void); 373 #endif 374 #define CONFIG_PCIE 375 #define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ 376 377 #define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */ 378 #define CONFIG_USB_EHCI_FSL 379 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 380 381 #undef CONFIG_EEPRO100 382 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 383 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 384 #endif /* CONFIG_PCI */ 385 386 /* 387 * TSEC 388 */ 389 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 390 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 391 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 392 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 393 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 394 395 /* 396 * TSEC ethernet configuration 397 */ 398 #define CONFIG_MII 1 /* MII PHY management */ 399 #define CONFIG_TSEC1 1 400 #define CONFIG_TSEC1_NAME "eTSEC0" 401 #define CONFIG_TSEC2 1 402 #define CONFIG_TSEC2_NAME "eTSEC1" 403 #define TSEC1_PHY_ADDR 2 404 #define TSEC2_PHY_ADDR 3 405 #define TSEC1_PHY_ADDR_SGMII 8 406 #define TSEC2_PHY_ADDR_SGMII 4 407 #define TSEC1_PHYIDX 0 408 #define TSEC2_PHYIDX 0 409 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 410 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 411 412 /* Options are: TSEC[0-1] */ 413 #define CONFIG_ETHPRIME "eTSEC1" 414 415 /* SERDES */ 416 #define CONFIG_FSL_SERDES 417 #define CONFIG_FSL_SERDES1 0xe3000 418 #define CONFIG_FSL_SERDES2 0xe3100 419 420 /* 421 * SATA 422 */ 423 #define CONFIG_LIBATA 424 #define CONFIG_FSL_SATA 425 426 #define CONFIG_SYS_SATA_MAX_DEVICE 2 427 #define CONFIG_SATA1 428 #define CONFIG_SYS_SATA1_OFFSET 0x18000 429 #define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) 430 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 431 #define CONFIG_SATA2 432 #define CONFIG_SYS_SATA2_OFFSET 0x19000 433 #define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) 434 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 435 436 #ifdef CONFIG_FSL_SATA 437 #define CONFIG_LBA48 438 #endif 439 440 /* 441 * Environment 442 */ 443 #ifndef CONFIG_SYS_RAMBOOT 444 #define CONFIG_ENV_ADDR \ 445 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 446 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 447 #define CONFIG_ENV_SIZE 0x2000 448 #else 449 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 450 #define CONFIG_ENV_SIZE 0x2000 451 #endif 452 453 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 454 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 455 456 /* 457 * BOOTP options 458 */ 459 #define CONFIG_BOOTP_BOOTFILESIZE 460 #define CONFIG_BOOTP_BOOTPATH 461 #define CONFIG_BOOTP_GATEWAY 462 #define CONFIG_BOOTP_HOSTNAME 463 464 /* 465 * Command line configuration. 466 */ 467 468 #if defined(CONFIG_PCI) 469 #define CONFIG_CMD_PCI 470 #endif 471 472 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 473 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 474 475 #undef CONFIG_WATCHDOG /* watchdog disabled */ 476 477 #ifdef CONFIG_MMC 478 #define CONFIG_FSL_ESDHC 479 #define CONFIG_FSL_ESDHC_PIN_MUX 480 #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR 481 #endif 482 483 /* 484 * Miscellaneous configurable options 485 */ 486 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 487 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 488 489 #if defined(CONFIG_CMD_KGDB) 490 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 491 #else 492 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 493 #endif 494 495 /* Print Buffer Size */ 496 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 497 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 498 /* Boot Argument Buffer Size */ 499 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 500 501 /* 502 * For booting Linux, the board info and command line data 503 * have to be in the first 256 MB of memory, since this is 504 * the maximum mapped by the Linux kernel during initialization. 505 */ 506 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 507 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 508 509 /* 510 * Core HID Setup 511 */ 512 #define CONFIG_SYS_HID0_INIT 0x000000000 513 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 514 HID0_ENABLE_INSTRUCTION_CACHE) 515 #define CONFIG_SYS_HID2 HID2_HBE 516 517 /* 518 * MMU Setup 519 */ 520 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 521 522 /* DDR: cache cacheable */ 523 #define CONFIG_SYS_SDRAM_LOWER CONFIG_SYS_SDRAM_BASE 524 #define CONFIG_SYS_SDRAM_UPPER (CONFIG_SYS_SDRAM_BASE + 0x10000000) 525 526 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_LOWER \ 527 | BATL_PP_RW \ 528 | BATL_MEMCOHERENCE) 529 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_LOWER \ 530 | BATU_BL_256M \ 531 | BATU_VS \ 532 | BATU_VP) 533 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 534 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 535 536 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_UPPER \ 537 | BATL_PP_RW \ 538 | BATL_MEMCOHERENCE) 539 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_UPPER \ 540 | BATU_BL_256M \ 541 | BATU_VS \ 542 | BATU_VP) 543 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 544 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 545 546 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 547 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR \ 548 | BATL_PP_RW \ 549 | BATL_CACHEINHIBIT \ 550 | BATL_GUARDEDSTORAGE) 551 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR \ 552 | BATU_BL_8M \ 553 | BATU_VS \ 554 | BATU_VP) 555 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 556 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 557 558 /* BCSR: cache-inhibit and guarded */ 559 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_BCSR \ 560 | BATL_PP_RW \ 561 | BATL_CACHEINHIBIT \ 562 | BATL_GUARDEDSTORAGE) 563 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_BCSR \ 564 | BATU_BL_128K \ 565 | BATU_VS \ 566 | BATU_VP) 567 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 568 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 569 570 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 571 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE \ 572 | BATL_PP_RW \ 573 | BATL_MEMCOHERENCE) 574 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE \ 575 | BATU_BL_32M \ 576 | BATU_VS \ 577 | BATU_VP) 578 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE \ 579 | BATL_PP_RW \ 580 | BATL_CACHEINHIBIT \ 581 | BATL_GUARDEDSTORAGE) 582 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 583 584 /* Stack in dcache: cacheable, no memory coherence */ 585 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 586 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ 587 | BATU_BL_128K \ 588 | BATU_VS \ 589 | BATU_VP) 590 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 591 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 592 593 #ifdef CONFIG_PCI 594 /* PCI MEM space: cacheable */ 595 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS \ 596 | BATL_PP_RW \ 597 | BATL_MEMCOHERENCE) 598 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS \ 599 | BATU_BL_256M \ 600 | BATU_VS \ 601 | BATU_VP) 602 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 603 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 604 /* PCI MMIO space: cache-inhibit and guarded */ 605 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS \ 606 | BATL_PP_RW \ 607 | BATL_CACHEINHIBIT \ 608 | BATL_GUARDEDSTORAGE) 609 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS \ 610 | BATU_BL_256M \ 611 | BATU_VS \ 612 | BATU_VP) 613 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 614 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 615 #else 616 #define CONFIG_SYS_IBAT6L (0) 617 #define CONFIG_SYS_IBAT6U (0) 618 #define CONFIG_SYS_IBAT7L (0) 619 #define CONFIG_SYS_IBAT7U (0) 620 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 621 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 622 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 623 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 624 #endif 625 626 #if defined(CONFIG_CMD_KGDB) 627 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 628 #endif 629 630 /* 631 * Environment Configuration 632 */ 633 634 #define CONFIG_ENV_OVERWRITE 635 636 #if defined(CONFIG_TSEC_ENET) 637 #define CONFIG_HAS_ETH0 638 #define CONFIG_HAS_ETH1 639 #endif 640 641 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 642 643 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 644 645 #define CONFIG_EXTRA_ENV_SETTINGS \ 646 "netdev=eth0\0" \ 647 "consoledev=ttyS0\0" \ 648 "ramdiskaddr=1000000\0" \ 649 "ramdiskfile=ramfs.83xx\0" \ 650 "fdtaddr=780000\0" \ 651 "fdtfile=mpc8379_mds.dtb\0" \ 652 "" 653 654 #define CONFIG_NFSBOOTCOMMAND \ 655 "setenv bootargs root=/dev/nfs rw " \ 656 "nfsroot=$serverip:$rootpath " \ 657 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 658 "$netdev:off " \ 659 "console=$consoledev,$baudrate $othbootargs;" \ 660 "tftp $loadaddr $bootfile;" \ 661 "tftp $fdtaddr $fdtfile;" \ 662 "bootm $loadaddr - $fdtaddr" 663 664 #define CONFIG_RAMBOOTCOMMAND \ 665 "setenv bootargs root=/dev/ram rw " \ 666 "console=$consoledev,$baudrate $othbootargs;" \ 667 "tftp $ramdiskaddr $ramdiskfile;" \ 668 "tftp $loadaddr $bootfile;" \ 669 "tftp $fdtaddr $fdtfile;" \ 670 "bootm $loadaddr $ramdiskaddr $fdtaddr" 671 672 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 673 674 #endif /* __CONFIG_H */ 675