1 /* 2 * (C) Copyright 2006-2010 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * mpc8349emds board configuration file 10 * 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 /* 17 * High Level Configuration Options 18 */ 19 #define CONFIG_E300 1 /* E300 Family */ 20 #define CONFIG_MPC834x 1 /* MPC834x family */ 21 #define CONFIG_MPC8349 1 /* MPC8349 specific */ 22 #define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */ 23 24 #define CONFIG_SYS_TEXT_BASE 0xFE000000 25 26 #define CONFIG_PCI_66M 27 #ifdef CONFIG_PCI_66M 28 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 29 #else 30 #define CONFIG_83XX_CLKIN 33000000 /* in Hz */ 31 #endif 32 33 #ifdef CONFIG_PCISLAVE 34 #define CONFIG_83XX_PCICLK 66666666 /* in Hz */ 35 #endif /* CONFIG_PCISLAVE */ 36 37 #ifndef CONFIG_SYS_CLK_FREQ 38 #ifdef CONFIG_PCI_66M 39 #define CONFIG_SYS_CLK_FREQ 66000000 40 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 41 #else 42 #define CONFIG_SYS_CLK_FREQ 33000000 43 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 44 #endif 45 #endif 46 47 #define CONFIG_SYS_IMMR 0xE0000000 48 49 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 50 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 51 #define CONFIG_SYS_MEMTEST_END 0x00100000 52 53 /* 54 * DDR Setup 55 */ 56 #define CONFIG_DDR_ECC /* support DDR ECC function */ 57 #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ 58 #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ 59 60 /* 61 * SYS_FSL_DDR2 is selected in Kconfig to use unified DDR driver 62 * unselect it to use old spd_sdram.c 63 */ 64 #define CONFIG_SYS_SPD_BUS_NUM 0 65 #define SPD_EEPROM_ADDRESS1 0x52 66 #define SPD_EEPROM_ADDRESS2 0x51 67 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 68 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 69 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 70 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 71 72 /* 73 * 32-bit data path mode. 74 * 75 * Please note that using this mode for devices with the real density of 64-bit 76 * effectively reduces the amount of available memory due to the effect of 77 * wrapping around while translating address to row/columns, for example in the 78 * 256MB module the upper 128MB get aliased with contents of the lower 79 * 128MB); normally this define should be used for devices with real 32-bit 80 * data path. 81 */ 82 #undef CONFIG_DDR_32BIT 83 84 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 85 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 86 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 87 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ 88 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) 89 #undef CONFIG_DDR_2T_TIMING 90 91 /* 92 * DDRCDR - DDR Control Driver Register 93 */ 94 #define CONFIG_SYS_DDRCDR_VALUE 0x80080001 95 96 #if defined(CONFIG_SPD_EEPROM) 97 /* 98 * Determine DDR configuration from I2C interface. 99 */ 100 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ 101 #else 102 /* 103 * Manually set up DDR parameters 104 */ 105 #define CONFIG_SYS_DDR_SIZE 256 /* MB */ 106 #if defined(CONFIG_DDR_II) 107 #define CONFIG_SYS_DDRCDR 0x80080001 108 #define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f 109 #define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102 110 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 111 #define CONFIG_SYS_DDR_TIMING_1 0x38357322 112 #define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 113 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 114 #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 115 #define CONFIG_SYS_DDR_MODE 0x47d00432 116 #define CONFIG_SYS_DDR_MODE2 0x8000c000 117 #define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 118 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 119 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 120 #else 121 #define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ 122 | CSCONFIG_ROW_BIT_13 \ 123 | CSCONFIG_COL_BIT_10) 124 #define CONFIG_SYS_DDR_TIMING_1 0x36332321 125 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 126 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 127 #define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ 128 129 #if defined(CONFIG_DDR_32BIT) 130 /* set burst length to 8 for 32-bit data path */ 131 /* DLL,normal,seq,4/2.5, 8 burst len */ 132 #define CONFIG_SYS_DDR_MODE 0x00000023 133 #else 134 /* the default burst length is 4 - for 64-bit data path */ 135 /* DLL,normal,seq,4/2.5, 4 burst len */ 136 #define CONFIG_SYS_DDR_MODE 0x00000022 137 #endif 138 #endif 139 #endif 140 141 /* 142 * SDRAM on the Local Bus 143 */ 144 #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ 145 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 146 147 /* 148 * FLASH on the Local Bus 149 */ 150 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 151 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 152 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ 153 #define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */ 154 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 155 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 156 157 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 158 | BR_PS_16 /* 16 bit port */ \ 159 | BR_MS_GPCM /* MSEL = GPCM */ \ 160 | BR_V) /* valid */ 161 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 162 | OR_UPM_XAM \ 163 | OR_GPCM_CSNT \ 164 | OR_GPCM_ACS_DIV2 \ 165 | OR_GPCM_XACS \ 166 | OR_GPCM_SCY_15 \ 167 | OR_GPCM_TRLX_SET \ 168 | OR_GPCM_EHTR_SET \ 169 | OR_GPCM_EAD) 170 171 /* window base at flash base */ 172 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 173 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 174 175 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 176 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ 177 178 #undef CONFIG_SYS_FLASH_CHECKSUM 179 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 180 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 181 182 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 183 184 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 185 #define CONFIG_SYS_RAMBOOT 186 #else 187 #undef CONFIG_SYS_RAMBOOT 188 #endif 189 190 /* 191 * BCSR register on local bus 32KB, 8-bit wide for MDS config reg 192 */ 193 #define CONFIG_SYS_BCSR 0xE2400000 194 /* Access window base at BCSR base */ 195 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 196 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 197 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 198 | BR_PS_8 \ 199 | BR_MS_GPCM \ 200 | BR_V) 201 /* 0x00000801 */ 202 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 203 | OR_GPCM_XAM \ 204 | OR_GPCM_CSNT \ 205 | OR_GPCM_SCY_15 \ 206 | OR_GPCM_TRLX_CLEAR \ 207 | OR_GPCM_EHTR_CLEAR) 208 /* 0xFFFFE8F0 */ 209 210 #define CONFIG_SYS_INIT_RAM_LOCK 1 211 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ 212 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 213 214 #define CONFIG_SYS_GBL_DATA_OFFSET \ 215 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 216 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 217 218 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 219 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ 220 221 /* 222 * Local Bus LCRR and LBCR regs 223 * LCRR: DLL bypass, Clock divider is 4 224 * External Local Bus rate is 225 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV 226 */ 227 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 228 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 229 #define CONFIG_SYS_LBC_LBCR 0x00000000 230 231 /* 232 * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory. 233 * if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM 234 */ 235 #undef CONFIG_SYS_LB_SDRAM 236 237 #ifdef CONFIG_SYS_LB_SDRAM 238 /* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */ 239 /* 240 * Base Register 2 and Option Register 2 configure SDRAM. 241 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 242 * 243 * For BR2, need: 244 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 245 * port-size = 32-bits = BR2[19:20] = 11 246 * no parity checking = BR2[21:22] = 00 247 * SDRAM for MSEL = BR2[24:26] = 011 248 * Valid = BR[31] = 1 249 * 250 * 0 4 8 12 16 20 24 28 251 * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 252 */ 253 254 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \ 255 | BR_PS_32 /* 32-bit port */ \ 256 | BR_MS_SDRAM /* MSEL = SDRAM */ \ 257 | BR_V) /* Valid */ 258 /* 0xF0001861 */ 259 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE 260 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 261 262 /* 263 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 264 * 265 * For OR2, need: 266 * 64MB mask for AM, OR2[0:7] = 1111 1100 267 * XAM, OR2[17:18] = 11 268 * 9 columns OR2[19-21] = 010 269 * 13 rows OR2[23-25] = 100 270 * EAD set for extra time OR[31] = 1 271 * 272 * 0 4 8 12 16 20 24 28 273 * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 274 */ 275 276 #define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \ 277 | OR_SDRAM_XAM \ 278 | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \ 279 | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \ 280 | OR_SDRAM_EAD) 281 /* 0xFC006901 */ 282 283 /* LB sdram refresh timer, about 6us */ 284 #define CONFIG_SYS_LBC_LSRT 0x32000000 285 /* LB refresh timer prescal, 266MHz/32 */ 286 #define CONFIG_SYS_LBC_MRTPR 0x20000000 287 288 #define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ 289 | LSDMR_BSMA1516 \ 290 | LSDMR_RFCR8 \ 291 | LSDMR_PRETOACT6 \ 292 | LSDMR_ACTTORW3 \ 293 | LSDMR_BL8 \ 294 | LSDMR_WRC3 \ 295 | LSDMR_CL3) 296 297 /* 298 * SDRAM Controller configuration sequence. 299 */ 300 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) 301 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 302 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 303 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) 304 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) 305 #endif 306 307 /* 308 * Serial Port 309 */ 310 #define CONFIG_CONS_INDEX 1 311 #define CONFIG_SYS_NS16550_SERIAL 312 #define CONFIG_SYS_NS16550_REG_SIZE 1 313 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 314 315 #define CONFIG_SYS_BAUDRATE_TABLE \ 316 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 317 318 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 319 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 320 321 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 322 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 323 324 /* I2C */ 325 #define CONFIG_SYS_I2C 326 #define CONFIG_SYS_I2C_FSL 327 #define CONFIG_SYS_FSL_I2C_SPEED 400000 328 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 329 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 330 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 331 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 332 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 333 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 334 335 /* SPI */ 336 #define CONFIG_MPC8XXX_SPI 337 #undef CONFIG_SOFT_SPI /* SPI bit-banged */ 338 339 /* GPIOs. Used as SPI chip selects */ 340 #define CONFIG_SYS_GPIO1_PRELIM 341 #define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */ 342 #define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */ 343 344 /* TSEC */ 345 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 346 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 347 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 348 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 349 350 /* USB */ 351 #define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */ 352 353 /* 354 * General PCI 355 * Addresses are mapped 1-1. 356 */ 357 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 358 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 359 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 360 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 361 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 362 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 363 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 364 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 365 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 366 367 #define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 368 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE 369 #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ 370 #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 371 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE 372 #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ 373 #define CONFIG_SYS_PCI2_IO_BASE 0x00000000 374 #define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 375 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ 376 377 #if defined(CONFIG_PCI) 378 379 #define PCI_ONE_PCI1 380 #if defined(PCI_64BIT) 381 #undef PCI_ALL_PCI1 382 #undef PCI_TWO_PCI1 383 #undef PCI_ONE_PCI1 384 #endif 385 386 #define CONFIG_83XX_PCI_STREAMING 387 388 #undef CONFIG_EEPRO100 389 #undef CONFIG_TULIP 390 391 #if !defined(CONFIG_PCI_PNP) 392 #define PCI_ENET0_IOADDR 0xFIXME 393 #define PCI_ENET0_MEMADDR 0xFIXME 394 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 395 #endif 396 397 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 398 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 399 400 #endif /* CONFIG_PCI */ 401 402 /* 403 * TSEC configuration 404 */ 405 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 406 407 #if defined(CONFIG_TSEC_ENET) 408 409 #define CONFIG_GMII 1 /* MII PHY management */ 410 #define CONFIG_TSEC1 1 411 #define CONFIG_TSEC1_NAME "TSEC0" 412 #define CONFIG_TSEC2 1 413 #define CONFIG_TSEC2_NAME "TSEC1" 414 #define TSEC1_PHY_ADDR 0 415 #define TSEC2_PHY_ADDR 1 416 #define TSEC1_PHYIDX 0 417 #define TSEC2_PHYIDX 0 418 #define TSEC1_FLAGS TSEC_GIGABIT 419 #define TSEC2_FLAGS TSEC_GIGABIT 420 421 /* Options are: TSEC[0-1] */ 422 #define CONFIG_ETHPRIME "TSEC0" 423 424 #endif /* CONFIG_TSEC_ENET */ 425 426 /* 427 * Configure on-board RTC 428 */ 429 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 430 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 431 432 /* 433 * Environment 434 */ 435 #ifndef CONFIG_SYS_RAMBOOT 436 #define CONFIG_ENV_ADDR \ 437 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 438 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 439 #define CONFIG_ENV_SIZE 0x2000 440 441 /* Address and size of Redundant Environment Sector */ 442 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 443 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 444 445 #else 446 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 447 #define CONFIG_ENV_SIZE 0x2000 448 #endif 449 450 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 451 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 452 453 /* 454 * BOOTP options 455 */ 456 #define CONFIG_BOOTP_BOOTFILESIZE 457 #define CONFIG_BOOTP_BOOTPATH 458 #define CONFIG_BOOTP_GATEWAY 459 #define CONFIG_BOOTP_HOSTNAME 460 461 /* 462 * Command line configuration. 463 */ 464 465 #if defined(CONFIG_PCI) 466 #define CONFIG_CMD_PCI 467 #endif 468 469 #undef CONFIG_WATCHDOG /* watchdog disabled */ 470 471 /* 472 * Miscellaneous configurable options 473 */ 474 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 475 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 476 477 #if defined(CONFIG_CMD_KGDB) 478 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 479 #else 480 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 481 #endif 482 483 /* Print Buffer Size */ 484 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 485 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 486 /* Boot Argument Buffer Size */ 487 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 488 489 /* 490 * For booting Linux, the board info and command line data 491 * have to be in the first 256 MB of memory, since this is 492 * the maximum mapped by the Linux kernel during initialization. 493 */ 494 /* Initial Memory map for Linux*/ 495 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 496 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 497 498 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ 499 500 #if 1 /*528/264*/ 501 #define CONFIG_SYS_HRCW_LOW (\ 502 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 503 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 504 HRCWL_CSB_TO_CLKIN |\ 505 HRCWL_VCO_1X2 |\ 506 HRCWL_CORE_TO_CSB_2X1) 507 #elif 0 /*396/132*/ 508 #define CONFIG_SYS_HRCW_LOW (\ 509 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 510 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 511 HRCWL_CSB_TO_CLKIN |\ 512 HRCWL_VCO_1X4 |\ 513 HRCWL_CORE_TO_CSB_3X1) 514 #elif 0 /*264/132*/ 515 #define CONFIG_SYS_HRCW_LOW (\ 516 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 517 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 518 HRCWL_CSB_TO_CLKIN |\ 519 HRCWL_VCO_1X4 |\ 520 HRCWL_CORE_TO_CSB_2X1) 521 #elif 0 /*132/132*/ 522 #define CONFIG_SYS_HRCW_LOW (\ 523 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 524 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 525 HRCWL_CSB_TO_CLKIN |\ 526 HRCWL_VCO_1X4 |\ 527 HRCWL_CORE_TO_CSB_1X1) 528 #elif 0 /*264/264 */ 529 #define CONFIG_SYS_HRCW_LOW (\ 530 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 531 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 532 HRCWL_CSB_TO_CLKIN |\ 533 HRCWL_VCO_1X4 |\ 534 HRCWL_CORE_TO_CSB_1X1) 535 #endif 536 537 #ifdef CONFIG_PCISLAVE 538 #define CONFIG_SYS_HRCW_HIGH (\ 539 HRCWH_PCI_AGENT |\ 540 HRCWH_64_BIT_PCI |\ 541 HRCWH_PCI1_ARBITER_DISABLE |\ 542 HRCWH_PCI2_ARBITER_DISABLE |\ 543 HRCWH_CORE_ENABLE |\ 544 HRCWH_FROM_0X00000100 |\ 545 HRCWH_BOOTSEQ_DISABLE |\ 546 HRCWH_SW_WATCHDOG_DISABLE |\ 547 HRCWH_ROM_LOC_LOCAL_16BIT |\ 548 HRCWH_TSEC1M_IN_GMII |\ 549 HRCWH_TSEC2M_IN_GMII) 550 #else 551 #if defined(PCI_64BIT) 552 #define CONFIG_SYS_HRCW_HIGH (\ 553 HRCWH_PCI_HOST |\ 554 HRCWH_64_BIT_PCI |\ 555 HRCWH_PCI1_ARBITER_ENABLE |\ 556 HRCWH_PCI2_ARBITER_DISABLE |\ 557 HRCWH_CORE_ENABLE |\ 558 HRCWH_FROM_0X00000100 |\ 559 HRCWH_BOOTSEQ_DISABLE |\ 560 HRCWH_SW_WATCHDOG_DISABLE |\ 561 HRCWH_ROM_LOC_LOCAL_16BIT |\ 562 HRCWH_TSEC1M_IN_GMII |\ 563 HRCWH_TSEC2M_IN_GMII) 564 #else 565 #define CONFIG_SYS_HRCW_HIGH (\ 566 HRCWH_PCI_HOST |\ 567 HRCWH_32_BIT_PCI |\ 568 HRCWH_PCI1_ARBITER_ENABLE |\ 569 HRCWH_PCI2_ARBITER_ENABLE |\ 570 HRCWH_CORE_ENABLE |\ 571 HRCWH_FROM_0X00000100 |\ 572 HRCWH_BOOTSEQ_DISABLE |\ 573 HRCWH_SW_WATCHDOG_DISABLE |\ 574 HRCWH_ROM_LOC_LOCAL_16BIT |\ 575 HRCWH_TSEC1M_IN_GMII |\ 576 HRCWH_TSEC2M_IN_GMII) 577 #endif /* PCI_64BIT */ 578 #endif /* CONFIG_PCISLAVE */ 579 580 /* 581 * System performance 582 */ 583 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 584 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 585 #define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ 586 #define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ 587 #define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ 588 #define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ 589 590 /* System IO Config */ 591 #define CONFIG_SYS_SICRH 0 592 #define CONFIG_SYS_SICRL SICRL_LDP_A 593 594 #define CONFIG_SYS_HID0_INIT 0x000000000 595 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ 596 | HID0_ENABLE_INSTRUCTION_CACHE) 597 598 /* #define CONFIG_SYS_HID0_FINAL (\ 599 HID0_ENABLE_INSTRUCTION_CACHE |\ 600 HID0_ENABLE_M_BIT |\ 601 HID0_ENABLE_ADDRESS_BROADCAST) */ 602 603 #define CONFIG_SYS_HID2 HID2_HBE 604 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 605 606 /* DDR @ 0x00000000 */ 607 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 608 | BATL_PP_RW \ 609 | BATL_MEMCOHERENCE) 610 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 611 | BATU_BL_256M \ 612 | BATU_VS \ 613 | BATU_VP) 614 615 /* PCI @ 0x80000000 */ 616 #ifdef CONFIG_PCI 617 #define CONFIG_PCI_INDIRECT_BRIDGE 618 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ 619 | BATL_PP_RW \ 620 | BATL_MEMCOHERENCE) 621 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ 622 | BATU_BL_256M \ 623 | BATU_VS \ 624 | BATU_VP) 625 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ 626 | BATL_PP_RW \ 627 | BATL_CACHEINHIBIT \ 628 | BATL_GUARDEDSTORAGE) 629 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ 630 | BATU_BL_256M \ 631 | BATU_VS \ 632 | BATU_VP) 633 #else 634 #define CONFIG_SYS_IBAT1L (0) 635 #define CONFIG_SYS_IBAT1U (0) 636 #define CONFIG_SYS_IBAT2L (0) 637 #define CONFIG_SYS_IBAT2U (0) 638 #endif 639 640 #ifdef CONFIG_MPC83XX_PCI2 641 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \ 642 | BATL_PP_RW \ 643 | BATL_MEMCOHERENCE) 644 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \ 645 | BATU_BL_256M \ 646 | BATU_VS \ 647 | BATU_VP) 648 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \ 649 | BATL_PP_RW \ 650 | BATL_CACHEINHIBIT \ 651 | BATL_GUARDEDSTORAGE) 652 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \ 653 | BATU_BL_256M \ 654 | BATU_VS \ 655 | BATU_VP) 656 #else 657 #define CONFIG_SYS_IBAT3L (0) 658 #define CONFIG_SYS_IBAT3U (0) 659 #define CONFIG_SYS_IBAT4L (0) 660 #define CONFIG_SYS_IBAT4U (0) 661 #endif 662 663 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 664 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ 665 | BATL_PP_RW \ 666 | BATL_CACHEINHIBIT \ 667 | BATL_GUARDEDSTORAGE) 668 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ 669 | BATU_BL_256M \ 670 | BATU_VS \ 671 | BATU_VP) 672 673 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 674 #define CONFIG_SYS_IBAT6L (0xF0000000 \ 675 | BATL_PP_RW \ 676 | BATL_MEMCOHERENCE \ 677 | BATL_GUARDEDSTORAGE) 678 #define CONFIG_SYS_IBAT6U (0xF0000000 \ 679 | BATU_BL_256M \ 680 | BATU_VS \ 681 | BATU_VP) 682 683 #define CONFIG_SYS_IBAT7L (0) 684 #define CONFIG_SYS_IBAT7U (0) 685 686 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 687 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 688 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 689 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 690 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 691 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 692 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 693 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 694 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 695 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 696 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 697 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 698 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 699 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 700 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 701 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 702 703 #if defined(CONFIG_CMD_KGDB) 704 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 705 #endif 706 707 /* 708 * Environment Configuration 709 */ 710 #define CONFIG_ENV_OVERWRITE 711 712 #if defined(CONFIG_TSEC_ENET) 713 #define CONFIG_HAS_ETH1 714 #define CONFIG_HAS_ETH0 715 #endif 716 717 #define CONFIG_HOSTNAME mpc8349emds 718 #define CONFIG_ROOTPATH "/nfsroot/rootfs" 719 #define CONFIG_BOOTFILE "uImage" 720 721 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 722 723 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 724 725 #define CONFIG_PREBOOT "echo;" \ 726 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ 727 "echo" 728 729 #define CONFIG_EXTRA_ENV_SETTINGS \ 730 "netdev=eth0\0" \ 731 "hostname=mpc8349emds\0" \ 732 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 733 "nfsroot=${serverip}:${rootpath}\0" \ 734 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 735 "addip=setenv bootargs ${bootargs} " \ 736 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 737 ":${hostname}:${netdev}:off panic=1\0" \ 738 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ 739 "flash_nfs=run nfsargs addip addtty;" \ 740 "bootm ${kernel_addr}\0" \ 741 "flash_self=run ramargs addip addtty;" \ 742 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 743 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ 744 "bootm\0" \ 745 "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \ 746 "update=protect off fe000000 fe03ffff; " \ 747 "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\ 748 "upd=run load update\0" \ 749 "fdtaddr=780000\0" \ 750 "fdtfile=mpc834x_mds.dtb\0" \ 751 "" 752 753 #define CONFIG_NFSBOOTCOMMAND \ 754 "setenv bootargs root=/dev/nfs rw " \ 755 "nfsroot=$serverip:$rootpath " \ 756 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 757 "$netdev:off " \ 758 "console=$consoledev,$baudrate $othbootargs;" \ 759 "tftp $loadaddr $bootfile;" \ 760 "tftp $fdtaddr $fdtfile;" \ 761 "bootm $loadaddr - $fdtaddr" 762 763 #define CONFIG_RAMBOOTCOMMAND \ 764 "setenv bootargs root=/dev/ram rw " \ 765 "console=$consoledev,$baudrate $othbootargs;" \ 766 "tftp $ramdiskaddr $ramdiskfile;" \ 767 "tftp $loadaddr $bootfile;" \ 768 "tftp $fdtaddr $fdtfile;" \ 769 "bootm $loadaddr $ramdiskaddr $fdtaddr" 770 771 #define CONFIG_BOOTCOMMAND "run flash_self" 772 773 #endif /* __CONFIG_H */ 774