1 /* 2 * (C) Copyright 2006-2010 3 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* 9 * mpc8349emds board configuration file 10 * 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #define CONFIG_DISPLAY_BOARDINFO 17 18 /* 19 * High Level Configuration Options 20 */ 21 #define CONFIG_E300 1 /* E300 Family */ 22 #define CONFIG_MPC834x 1 /* MPC834x family */ 23 #define CONFIG_MPC8349 1 /* MPC8349 specific */ 24 #define CONFIG_MPC8349EMDS 1 /* MPC8349EMDS board specific */ 25 26 #define CONFIG_SYS_TEXT_BASE 0xFE000000 27 28 #define CONFIG_PCI_66M 29 #ifdef CONFIG_PCI_66M 30 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 31 #else 32 #define CONFIG_83XX_CLKIN 33000000 /* in Hz */ 33 #endif 34 35 #ifdef CONFIG_PCISLAVE 36 #define CONFIG_PCI 37 #define CONFIG_83XX_PCICLK 66666666 /* in Hz */ 38 #endif /* CONFIG_PCISLAVE */ 39 40 #ifndef CONFIG_SYS_CLK_FREQ 41 #ifdef CONFIG_PCI_66M 42 #define CONFIG_SYS_CLK_FREQ 66000000 43 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 44 #else 45 #define CONFIG_SYS_CLK_FREQ 33000000 46 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 47 #endif 48 #endif 49 50 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 51 52 #define CONFIG_SYS_IMMR 0xE0000000 53 54 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 55 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 56 #define CONFIG_SYS_MEMTEST_END 0x00100000 57 58 /* 59 * DDR Setup 60 */ 61 #define CONFIG_DDR_ECC /* support DDR ECC function */ 62 #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ 63 #define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/ 64 65 /* 66 * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver 67 * undefine it to use old spd_sdram.c 68 */ 69 #define CONFIG_SYS_FSL_DDR2 70 #ifdef CONFIG_SYS_FSL_DDR2 71 #define CONFIG_SYS_FSL_DDRC_GEN2 72 #define CONFIG_SYS_SPD_BUS_NUM 0 73 #define SPD_EEPROM_ADDRESS1 0x52 74 #define SPD_EEPROM_ADDRESS2 0x51 75 #define CONFIG_NUM_DDR_CONTROLLERS 1 76 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 77 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 78 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 79 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 80 #endif 81 82 /* 83 * 32-bit data path mode. 84 * 85 * Please note that using this mode for devices with the real density of 64-bit 86 * effectively reduces the amount of available memory due to the effect of 87 * wrapping around while translating address to row/columns, for example in the 88 * 256MB module the upper 128MB get aliased with contents of the lower 89 * 128MB); normally this define should be used for devices with real 32-bit 90 * data path. 91 */ 92 #undef CONFIG_DDR_32BIT 93 94 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ 95 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 96 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 97 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ 98 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) 99 #undef CONFIG_DDR_2T_TIMING 100 101 /* 102 * DDRCDR - DDR Control Driver Register 103 */ 104 #define CONFIG_SYS_DDRCDR_VALUE 0x80080001 105 106 #if defined(CONFIG_SPD_EEPROM) 107 /* 108 * Determine DDR configuration from I2C interface. 109 */ 110 #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ 111 #else 112 /* 113 * Manually set up DDR parameters 114 */ 115 #define CONFIG_SYS_DDR_SIZE 256 /* MB */ 116 #if defined(CONFIG_DDR_II) 117 #define CONFIG_SYS_DDRCDR 0x80080001 118 #define CONFIG_SYS_DDR_CS2_BNDS 0x0000000f 119 #define CONFIG_SYS_DDR_CS2_CONFIG 0x80330102 120 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 121 #define CONFIG_SYS_DDR_TIMING_1 0x38357322 122 #define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 123 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 124 #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 125 #define CONFIG_SYS_DDR_MODE 0x47d00432 126 #define CONFIG_SYS_DDR_MODE2 0x8000c000 127 #define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 128 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 129 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 130 #else 131 #define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \ 132 | CSCONFIG_ROW_BIT_13 \ 133 | CSCONFIG_COL_BIT_10) 134 #define CONFIG_SYS_DDR_TIMING_1 0x36332321 135 #define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ 136 #define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ 137 #define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */ 138 139 #if defined(CONFIG_DDR_32BIT) 140 /* set burst length to 8 for 32-bit data path */ 141 /* DLL,normal,seq,4/2.5, 8 burst len */ 142 #define CONFIG_SYS_DDR_MODE 0x00000023 143 #else 144 /* the default burst length is 4 - for 64-bit data path */ 145 /* DLL,normal,seq,4/2.5, 4 burst len */ 146 #define CONFIG_SYS_DDR_MODE 0x00000022 147 #endif 148 #endif 149 #endif 150 151 /* 152 * SDRAM on the Local Bus 153 */ 154 #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */ 155 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 156 157 /* 158 * FLASH on the Local Bus 159 */ 160 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 161 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 162 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ 163 #define CONFIG_SYS_FLASH_SIZE 32 /* max flash size in MB */ 164 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 165 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 166 167 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 168 | BR_PS_16 /* 16 bit port */ \ 169 | BR_MS_GPCM /* MSEL = GPCM */ \ 170 | BR_V) /* valid */ 171 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 172 | OR_UPM_XAM \ 173 | OR_GPCM_CSNT \ 174 | OR_GPCM_ACS_DIV2 \ 175 | OR_GPCM_XACS \ 176 | OR_GPCM_SCY_15 \ 177 | OR_GPCM_TRLX_SET \ 178 | OR_GPCM_EHTR_SET \ 179 | OR_GPCM_EAD) 180 181 /* window base at flash base */ 182 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 183 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 184 185 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 186 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ 187 188 #undef CONFIG_SYS_FLASH_CHECKSUM 189 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 190 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 191 192 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 193 194 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 195 #define CONFIG_SYS_RAMBOOT 196 #else 197 #undef CONFIG_SYS_RAMBOOT 198 #endif 199 200 /* 201 * BCSR register on local bus 32KB, 8-bit wide for MDS config reg 202 */ 203 #define CONFIG_SYS_BCSR 0xE2400000 204 /* Access window base at BCSR base */ 205 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 206 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 207 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 208 | BR_PS_8 \ 209 | BR_MS_GPCM \ 210 | BR_V) 211 /* 0x00000801 */ 212 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 213 | OR_GPCM_XAM \ 214 | OR_GPCM_CSNT \ 215 | OR_GPCM_SCY_15 \ 216 | OR_GPCM_TRLX_CLEAR \ 217 | OR_GPCM_EHTR_CLEAR) 218 /* 0xFFFFE8F0 */ 219 220 #define CONFIG_SYS_INIT_RAM_LOCK 1 221 #define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM addr */ 222 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ 223 224 #define CONFIG_SYS_GBL_DATA_OFFSET \ 225 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 226 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 227 228 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 229 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ 230 231 /* 232 * Local Bus LCRR and LBCR regs 233 * LCRR: DLL bypass, Clock divider is 4 234 * External Local Bus rate is 235 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV 236 */ 237 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 238 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 239 #define CONFIG_SYS_LBC_LBCR 0x00000000 240 241 /* 242 * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory. 243 * if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM 244 */ 245 #undef CONFIG_SYS_LB_SDRAM 246 247 #ifdef CONFIG_SYS_LB_SDRAM 248 /* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */ 249 /* 250 * Base Register 2 and Option Register 2 configure SDRAM. 251 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 252 * 253 * For BR2, need: 254 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 255 * port-size = 32-bits = BR2[19:20] = 11 256 * no parity checking = BR2[21:22] = 00 257 * SDRAM for MSEL = BR2[24:26] = 011 258 * Valid = BR[31] = 1 259 * 260 * 0 4 8 12 16 20 24 28 261 * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861 262 */ 263 264 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_LBC_SDRAM_BASE \ 265 | BR_PS_32 /* 32-bit port */ \ 266 | BR_MS_SDRAM /* MSEL = SDRAM */ \ 267 | BR_V) /* Valid */ 268 /* 0xF0001861 */ 269 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE 270 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) 271 272 /* 273 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 274 * 275 * For OR2, need: 276 * 64MB mask for AM, OR2[0:7] = 1111 1100 277 * XAM, OR2[17:18] = 11 278 * 9 columns OR2[19-21] = 010 279 * 13 rows OR2[23-25] = 100 280 * EAD set for extra time OR[31] = 1 281 * 282 * 0 4 8 12 16 20 24 28 283 * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901 284 */ 285 286 #define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB \ 287 | OR_SDRAM_XAM \ 288 | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \ 289 | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \ 290 | OR_SDRAM_EAD) 291 /* 0xFC006901 */ 292 293 /* LB sdram refresh timer, about 6us */ 294 #define CONFIG_SYS_LBC_LSRT 0x32000000 295 /* LB refresh timer prescal, 266MHz/32 */ 296 #define CONFIG_SYS_LBC_MRTPR 0x20000000 297 298 #define CONFIG_SYS_LBC_LSDMR_COMMON (LSDMR_RFEN \ 299 | LSDMR_BSMA1516 \ 300 | LSDMR_RFCR8 \ 301 | LSDMR_PRETOACT6 \ 302 | LSDMR_ACTTORW3 \ 303 | LSDMR_BL8 \ 304 | LSDMR_WRC3 \ 305 | LSDMR_CL3) 306 307 /* 308 * SDRAM Controller configuration sequence. 309 */ 310 #define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) 311 #define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 312 #define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) 313 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) 314 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) 315 #endif 316 317 /* 318 * Serial Port 319 */ 320 #define CONFIG_CONS_INDEX 1 321 #define CONFIG_SYS_NS16550 322 #define CONFIG_SYS_NS16550_SERIAL 323 #define CONFIG_SYS_NS16550_REG_SIZE 1 324 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 325 326 #define CONFIG_SYS_BAUDRATE_TABLE \ 327 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 328 329 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 330 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 331 332 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 333 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 334 /* Use the HUSH parser */ 335 #define CONFIG_SYS_HUSH_PARSER 336 337 /* pass open firmware flat tree */ 338 #define CONFIG_OF_LIBFDT 1 339 #define CONFIG_OF_BOARD_SETUP 1 340 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 341 342 /* I2C */ 343 #define CONFIG_SYS_I2C 344 #define CONFIG_SYS_I2C_FSL 345 #define CONFIG_SYS_FSL_I2C_SPEED 400000 346 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 347 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 348 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 349 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 350 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 351 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 352 353 /* SPI */ 354 #define CONFIG_MPC8XXX_SPI 355 #undef CONFIG_SOFT_SPI /* SPI bit-banged */ 356 357 /* GPIOs. Used as SPI chip selects */ 358 #define CONFIG_SYS_GPIO1_PRELIM 359 #define CONFIG_SYS_GPIO1_DIR 0xC0000000 /* SPI CS on 0, LED on 1 */ 360 #define CONFIG_SYS_GPIO1_DAT 0xC0000000 /* Both are active LOW */ 361 362 /* TSEC */ 363 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 364 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 365 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 366 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 367 368 /* USB */ 369 #define CONFIG_SYS_USE_MPC834XSYS_USB_PHY 1 /* Use SYS board PHY */ 370 371 /* 372 * General PCI 373 * Addresses are mapped 1-1. 374 */ 375 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 376 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 377 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 378 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 379 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 380 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 381 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 382 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 383 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 384 385 #define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 386 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE 387 #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ 388 #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 389 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE 390 #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ 391 #define CONFIG_SYS_PCI2_IO_BASE 0x00000000 392 #define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 393 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ 394 395 #if defined(CONFIG_PCI) 396 397 #define PCI_ONE_PCI1 398 #if defined(PCI_64BIT) 399 #undef PCI_ALL_PCI1 400 #undef PCI_TWO_PCI1 401 #undef PCI_ONE_PCI1 402 #endif 403 404 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 405 #define CONFIG_83XX_PCI_STREAMING 406 407 #undef CONFIG_EEPRO100 408 #undef CONFIG_TULIP 409 410 #if !defined(CONFIG_PCI_PNP) 411 #define PCI_ENET0_IOADDR 0xFIXME 412 #define PCI_ENET0_MEMADDR 0xFIXME 413 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ 414 #endif 415 416 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 417 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 418 419 #endif /* CONFIG_PCI */ 420 421 /* 422 * TSEC configuration 423 */ 424 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 425 426 #if defined(CONFIG_TSEC_ENET) 427 428 #define CONFIG_GMII 1 /* MII PHY management */ 429 #define CONFIG_TSEC1 1 430 #define CONFIG_TSEC1_NAME "TSEC0" 431 #define CONFIG_TSEC2 1 432 #define CONFIG_TSEC2_NAME "TSEC1" 433 #define TSEC1_PHY_ADDR 0 434 #define TSEC2_PHY_ADDR 1 435 #define TSEC1_PHYIDX 0 436 #define TSEC2_PHYIDX 0 437 #define TSEC1_FLAGS TSEC_GIGABIT 438 #define TSEC2_FLAGS TSEC_GIGABIT 439 440 /* Options are: TSEC[0-1] */ 441 #define CONFIG_ETHPRIME "TSEC0" 442 443 #endif /* CONFIG_TSEC_ENET */ 444 445 /* 446 * Configure on-board RTC 447 */ 448 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 449 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 450 451 /* 452 * Environment 453 */ 454 #ifndef CONFIG_SYS_RAMBOOT 455 #define CONFIG_ENV_IS_IN_FLASH 1 456 #define CONFIG_ENV_ADDR \ 457 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 458 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 459 #define CONFIG_ENV_SIZE 0x2000 460 461 /* Address and size of Redundant Environment Sector */ 462 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 463 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 464 465 #else 466 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 467 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 468 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 469 #define CONFIG_ENV_SIZE 0x2000 470 #endif 471 472 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 473 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 474 475 476 /* 477 * BOOTP options 478 */ 479 #define CONFIG_BOOTP_BOOTFILESIZE 480 #define CONFIG_BOOTP_BOOTPATH 481 #define CONFIG_BOOTP_GATEWAY 482 #define CONFIG_BOOTP_HOSTNAME 483 484 485 /* 486 * Command line configuration. 487 */ 488 #define CONFIG_CMD_PING 489 #define CONFIG_CMD_I2C 490 #define CONFIG_CMD_DATE 491 #define CONFIG_CMD_MII 492 493 #if defined(CONFIG_PCI) 494 #define CONFIG_CMD_PCI 495 #endif 496 497 #undef CONFIG_WATCHDOG /* watchdog disabled */ 498 499 /* 500 * Miscellaneous configurable options 501 */ 502 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 503 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 504 505 #if defined(CONFIG_CMD_KGDB) 506 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 507 #else 508 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 509 #endif 510 511 /* Print Buffer Size */ 512 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 513 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 514 /* Boot Argument Buffer Size */ 515 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 516 517 /* 518 * For booting Linux, the board info and command line data 519 * have to be in the first 256 MB of memory, since this is 520 * the maximum mapped by the Linux kernel during initialization. 521 */ 522 /* Initial Memory map for Linux*/ 523 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 524 525 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ 526 527 #if 1 /*528/264*/ 528 #define CONFIG_SYS_HRCW_LOW (\ 529 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 530 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 531 HRCWL_CSB_TO_CLKIN |\ 532 HRCWL_VCO_1X2 |\ 533 HRCWL_CORE_TO_CSB_2X1) 534 #elif 0 /*396/132*/ 535 #define CONFIG_SYS_HRCW_LOW (\ 536 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 537 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 538 HRCWL_CSB_TO_CLKIN |\ 539 HRCWL_VCO_1X4 |\ 540 HRCWL_CORE_TO_CSB_3X1) 541 #elif 0 /*264/132*/ 542 #define CONFIG_SYS_HRCW_LOW (\ 543 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 544 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 545 HRCWL_CSB_TO_CLKIN |\ 546 HRCWL_VCO_1X4 |\ 547 HRCWL_CORE_TO_CSB_2X1) 548 #elif 0 /*132/132*/ 549 #define CONFIG_SYS_HRCW_LOW (\ 550 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 551 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 552 HRCWL_CSB_TO_CLKIN |\ 553 HRCWL_VCO_1X4 |\ 554 HRCWL_CORE_TO_CSB_1X1) 555 #elif 0 /*264/264 */ 556 #define CONFIG_SYS_HRCW_LOW (\ 557 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 558 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 559 HRCWL_CSB_TO_CLKIN |\ 560 HRCWL_VCO_1X4 |\ 561 HRCWL_CORE_TO_CSB_1X1) 562 #endif 563 564 #ifdef CONFIG_PCISLAVE 565 #define CONFIG_SYS_HRCW_HIGH (\ 566 HRCWH_PCI_AGENT |\ 567 HRCWH_64_BIT_PCI |\ 568 HRCWH_PCI1_ARBITER_DISABLE |\ 569 HRCWH_PCI2_ARBITER_DISABLE |\ 570 HRCWH_CORE_ENABLE |\ 571 HRCWH_FROM_0X00000100 |\ 572 HRCWH_BOOTSEQ_DISABLE |\ 573 HRCWH_SW_WATCHDOG_DISABLE |\ 574 HRCWH_ROM_LOC_LOCAL_16BIT |\ 575 HRCWH_TSEC1M_IN_GMII |\ 576 HRCWH_TSEC2M_IN_GMII) 577 #else 578 #if defined(PCI_64BIT) 579 #define CONFIG_SYS_HRCW_HIGH (\ 580 HRCWH_PCI_HOST |\ 581 HRCWH_64_BIT_PCI |\ 582 HRCWH_PCI1_ARBITER_ENABLE |\ 583 HRCWH_PCI2_ARBITER_DISABLE |\ 584 HRCWH_CORE_ENABLE |\ 585 HRCWH_FROM_0X00000100 |\ 586 HRCWH_BOOTSEQ_DISABLE |\ 587 HRCWH_SW_WATCHDOG_DISABLE |\ 588 HRCWH_ROM_LOC_LOCAL_16BIT |\ 589 HRCWH_TSEC1M_IN_GMII |\ 590 HRCWH_TSEC2M_IN_GMII) 591 #else 592 #define CONFIG_SYS_HRCW_HIGH (\ 593 HRCWH_PCI_HOST |\ 594 HRCWH_32_BIT_PCI |\ 595 HRCWH_PCI1_ARBITER_ENABLE |\ 596 HRCWH_PCI2_ARBITER_ENABLE |\ 597 HRCWH_CORE_ENABLE |\ 598 HRCWH_FROM_0X00000100 |\ 599 HRCWH_BOOTSEQ_DISABLE |\ 600 HRCWH_SW_WATCHDOG_DISABLE |\ 601 HRCWH_ROM_LOC_LOCAL_16BIT |\ 602 HRCWH_TSEC1M_IN_GMII |\ 603 HRCWH_TSEC2M_IN_GMII) 604 #endif /* PCI_64BIT */ 605 #endif /* CONFIG_PCISLAVE */ 606 607 /* 608 * System performance 609 */ 610 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ 611 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ 612 #define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ 613 #define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ 614 #define CONFIG_SYS_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */ 615 #define CONFIG_SYS_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */ 616 617 /* System IO Config */ 618 #define CONFIG_SYS_SICRH 0 619 #define CONFIG_SYS_SICRL SICRL_LDP_A 620 621 #define CONFIG_SYS_HID0_INIT 0x000000000 622 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ 623 | HID0_ENABLE_INSTRUCTION_CACHE) 624 625 /* #define CONFIG_SYS_HID0_FINAL (\ 626 HID0_ENABLE_INSTRUCTION_CACHE |\ 627 HID0_ENABLE_M_BIT |\ 628 HID0_ENABLE_ADDRESS_BROADCAST) */ 629 630 631 #define CONFIG_SYS_HID2 HID2_HBE 632 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 633 634 /* DDR @ 0x00000000 */ 635 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 636 | BATL_PP_RW \ 637 | BATL_MEMCOHERENCE) 638 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 639 | BATU_BL_256M \ 640 | BATU_VS \ 641 | BATU_VP) 642 643 /* PCI @ 0x80000000 */ 644 #ifdef CONFIG_PCI 645 #define CONFIG_PCI_INDIRECT_BRIDGE 646 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ 647 | BATL_PP_RW \ 648 | BATL_MEMCOHERENCE) 649 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ 650 | BATU_BL_256M \ 651 | BATU_VS \ 652 | BATU_VP) 653 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ 654 | BATL_PP_RW \ 655 | BATL_CACHEINHIBIT \ 656 | BATL_GUARDEDSTORAGE) 657 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ 658 | BATU_BL_256M \ 659 | BATU_VS \ 660 | BATU_VP) 661 #else 662 #define CONFIG_SYS_IBAT1L (0) 663 #define CONFIG_SYS_IBAT1U (0) 664 #define CONFIG_SYS_IBAT2L (0) 665 #define CONFIG_SYS_IBAT2U (0) 666 #endif 667 668 #ifdef CONFIG_MPC83XX_PCI2 669 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE \ 670 | BATL_PP_RW \ 671 | BATL_MEMCOHERENCE) 672 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE \ 673 | BATU_BL_256M \ 674 | BATU_VS \ 675 | BATU_VP) 676 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE \ 677 | BATL_PP_RW \ 678 | BATL_CACHEINHIBIT \ 679 | BATL_GUARDEDSTORAGE) 680 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE \ 681 | BATU_BL_256M \ 682 | BATU_VS \ 683 | BATU_VP) 684 #else 685 #define CONFIG_SYS_IBAT3L (0) 686 #define CONFIG_SYS_IBAT3U (0) 687 #define CONFIG_SYS_IBAT4L (0) 688 #define CONFIG_SYS_IBAT4U (0) 689 #endif 690 691 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ 692 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ 693 | BATL_PP_RW \ 694 | BATL_CACHEINHIBIT \ 695 | BATL_GUARDEDSTORAGE) 696 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ 697 | BATU_BL_256M \ 698 | BATU_VS \ 699 | BATU_VP) 700 701 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ 702 #define CONFIG_SYS_IBAT6L (0xF0000000 \ 703 | BATL_PP_RW \ 704 | BATL_MEMCOHERENCE \ 705 | BATL_GUARDEDSTORAGE) 706 #define CONFIG_SYS_IBAT6U (0xF0000000 \ 707 | BATU_BL_256M \ 708 | BATU_VS \ 709 | BATU_VP) 710 711 #define CONFIG_SYS_IBAT7L (0) 712 #define CONFIG_SYS_IBAT7U (0) 713 714 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 715 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 716 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 717 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 718 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 719 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 720 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 721 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 722 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 723 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 724 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 725 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 726 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 727 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 728 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 729 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 730 731 #if defined(CONFIG_CMD_KGDB) 732 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 733 #endif 734 735 /* 736 * Environment Configuration 737 */ 738 #define CONFIG_ENV_OVERWRITE 739 740 #if defined(CONFIG_TSEC_ENET) 741 #define CONFIG_HAS_ETH1 742 #define CONFIG_HAS_ETH0 743 #endif 744 745 #define CONFIG_HOSTNAME mpc8349emds 746 #define CONFIG_ROOTPATH "/nfsroot/rootfs" 747 #define CONFIG_BOOTFILE "uImage" 748 749 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 750 751 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 752 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 753 754 #define CONFIG_BAUDRATE 115200 755 756 #define CONFIG_PREBOOT "echo;" \ 757 "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ 758 "echo" 759 760 #define CONFIG_EXTRA_ENV_SETTINGS \ 761 "netdev=eth0\0" \ 762 "hostname=mpc8349emds\0" \ 763 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 764 "nfsroot=${serverip}:${rootpath}\0" \ 765 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 766 "addip=setenv bootargs ${bootargs} " \ 767 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 768 ":${hostname}:${netdev}:off panic=1\0" \ 769 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ 770 "flash_nfs=run nfsargs addip addtty;" \ 771 "bootm ${kernel_addr}\0" \ 772 "flash_self=run ramargs addip addtty;" \ 773 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 774 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ 775 "bootm\0" \ 776 "load=tftp 100000 /tftpboot/mpc8349emds/u-boot.bin\0" \ 777 "update=protect off fe000000 fe03ffff; " \ 778 "era fe000000 fe03ffff; cp.b 100000 fe000000 ${filesize}\0"\ 779 "upd=run load update\0" \ 780 "fdtaddr=780000\0" \ 781 "fdtfile=mpc834x_mds.dtb\0" \ 782 "" 783 784 #define CONFIG_NFSBOOTCOMMAND \ 785 "setenv bootargs root=/dev/nfs rw " \ 786 "nfsroot=$serverip:$rootpath " \ 787 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 788 "$netdev:off " \ 789 "console=$consoledev,$baudrate $othbootargs;" \ 790 "tftp $loadaddr $bootfile;" \ 791 "tftp $fdtaddr $fdtfile;" \ 792 "bootm $loadaddr - $fdtaddr" 793 794 #define CONFIG_RAMBOOTCOMMAND \ 795 "setenv bootargs root=/dev/ram rw " \ 796 "console=$consoledev,$baudrate $othbootargs;" \ 797 "tftp $ramdiskaddr $ramdiskfile;" \ 798 "tftp $loadaddr $bootfile;" \ 799 "tftp $fdtaddr $fdtfile;" \ 800 "bootm $loadaddr $ramdiskaddr $fdtaddr" 801 802 #define CONFIG_BOOTCOMMAND "run flash_self" 803 804 #endif /* __CONFIG_H */ 805