1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2006 Freescale Semiconductor, Inc. 4 */ 5 6 #ifndef __CONFIG_H 7 #define __CONFIG_H 8 9 /* 10 * High Level Configuration Options 11 */ 12 #define CONFIG_E300 1 /* E300 family */ 13 #define CONFIG_QE 1 /* Has QE */ 14 #define CONFIG_MPC832x 1 /* MPC832x CPU specific */ 15 #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ 16 17 /* 18 * System Clock Setup 19 */ 20 #ifdef CONFIG_PCISLAVE 21 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 22 #else 23 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 24 #endif 25 26 #ifndef CONFIG_SYS_CLK_FREQ 27 #define CONFIG_SYS_CLK_FREQ 66000000 28 #endif 29 30 /* 31 * Hardware Reset Configuration Word 32 */ 33 #define CONFIG_SYS_HRCW_LOW (\ 34 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 35 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 36 HRCWL_VCO_1X2 |\ 37 HRCWL_CSB_TO_CLKIN_2X1 |\ 38 HRCWL_CORE_TO_CSB_2X1 |\ 39 HRCWL_CE_PLL_VCO_DIV_2 |\ 40 HRCWL_CE_PLL_DIV_1X1 |\ 41 HRCWL_CE_TO_PLL_1X3) 42 43 #ifdef CONFIG_PCISLAVE 44 #define CONFIG_SYS_HRCW_HIGH (\ 45 HRCWH_PCI_AGENT |\ 46 HRCWH_PCI1_ARBITER_DISABLE |\ 47 HRCWH_CORE_ENABLE |\ 48 HRCWH_FROM_0XFFF00100 |\ 49 HRCWH_BOOTSEQ_DISABLE |\ 50 HRCWH_SW_WATCHDOG_DISABLE |\ 51 HRCWH_ROM_LOC_LOCAL_16BIT |\ 52 HRCWH_BIG_ENDIAN |\ 53 HRCWH_LALE_NORMAL) 54 #else 55 #define CONFIG_SYS_HRCW_HIGH (\ 56 HRCWH_PCI_HOST |\ 57 HRCWH_PCI1_ARBITER_ENABLE |\ 58 HRCWH_CORE_ENABLE |\ 59 HRCWH_FROM_0X00000100 |\ 60 HRCWH_BOOTSEQ_DISABLE |\ 61 HRCWH_SW_WATCHDOG_DISABLE |\ 62 HRCWH_ROM_LOC_LOCAL_16BIT |\ 63 HRCWH_BIG_ENDIAN |\ 64 HRCWH_LALE_NORMAL) 65 #endif 66 67 /* 68 * System IO Config 69 */ 70 #define CONFIG_SYS_SICRL 0x00000000 71 72 /* 73 * IMMR new address 74 */ 75 #define CONFIG_SYS_IMMR 0xE0000000 76 77 /* 78 * DDR Setup 79 */ 80 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 81 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 82 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 83 #define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ 84 85 #undef CONFIG_SPD_EEPROM 86 #if defined(CONFIG_SPD_EEPROM) 87 /* Determine DDR configuration from I2C interface 88 */ 89 #define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ 90 #else 91 /* Manually set up DDR parameters 92 */ 93 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 94 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 95 | CSCONFIG_AP \ 96 | CSCONFIG_ODT_WR_CFG \ 97 | CSCONFIG_ROW_BIT_13 \ 98 | CSCONFIG_COL_BIT_10) 99 /* 0x80840102 */ 100 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 101 | (0 << TIMING_CFG0_WRT_SHIFT) \ 102 | (0 << TIMING_CFG0_RRT_SHIFT) \ 103 | (0 << TIMING_CFG0_WWT_SHIFT) \ 104 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 105 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 106 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 107 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 108 /* 0x00220802 */ 109 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ 110 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 111 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ 112 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 113 | (13 << TIMING_CFG1_REFREC_SHIFT) \ 114 | (3 << TIMING_CFG1_WRREC_SHIFT) \ 115 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 116 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 117 /* 0x3935D322 */ 118 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 119 | (31 << TIMING_CFG2_CPO_SHIFT) \ 120 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 121 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 122 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 123 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 124 | (10 << TIMING_CFG2_FOUR_ACT_SHIFT)) 125 /* 0x0F9048CA */ 126 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 127 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 128 /* 0x02000000 */ 129 #define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ 130 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 131 /* 0x44400232 */ 132 #define CONFIG_SYS_DDR_MODE2 0x8000c000 133 #define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \ 134 | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 135 /* 0x03200064 */ 136 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 137 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 138 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 139 | SDRAM_CFG_32_BE) 140 /* 0x43080000 */ 141 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 142 #endif 143 144 /* 145 * Memory test 146 */ 147 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 148 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 149 #define CONFIG_SYS_MEMTEST_END 0x00100000 150 151 /* 152 * The reserved memory 153 */ 154 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 155 156 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 157 #define CONFIG_SYS_RAMBOOT 158 #else 159 #undef CONFIG_SYS_RAMBOOT 160 #endif 161 162 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 163 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 164 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ 165 166 /* 167 * Initial RAM Base Address Setup 168 */ 169 #define CONFIG_SYS_INIT_RAM_LOCK 1 170 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM addr */ 171 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 172 #define CONFIG_SYS_GBL_DATA_OFFSET \ 173 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 174 175 /* 176 * Local Bus Configuration & Clock Setup 177 */ 178 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 179 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 180 #define CONFIG_SYS_LBC_LBCR 0x00000000 181 182 /* 183 * FLASH on the Local Bus 184 */ 185 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 186 #define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ 187 188 /* Window base at flash base */ 189 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 190 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 191 192 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 193 | BR_PS_16 /* 16 bit port */ \ 194 | BR_MS_GPCM /* MSEL = GPCM */ \ 195 | BR_V) /* valid */ 196 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 197 | OR_GPCM_XAM \ 198 | OR_GPCM_CSNT \ 199 | OR_GPCM_ACS_DIV2 \ 200 | OR_GPCM_XACS \ 201 | OR_GPCM_SCY_15 \ 202 | OR_GPCM_TRLX_SET \ 203 | OR_GPCM_EHTR_SET \ 204 | OR_GPCM_EAD) 205 /* 0xfe006ff7 */ 206 207 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 208 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 209 210 #undef CONFIG_SYS_FLASH_CHECKSUM 211 212 /* 213 * BCSR on the Local Bus 214 */ 215 #define CONFIG_SYS_BCSR 0xF8000000 216 /* Access window base at BCSR base */ 217 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 218 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 219 220 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 221 | BR_PS_8 \ 222 | BR_MS_GPCM \ 223 | BR_V) 224 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 225 | OR_GPCM_XAM \ 226 | OR_GPCM_CSNT \ 227 | OR_GPCM_XACS \ 228 | OR_GPCM_SCY_15 \ 229 | OR_GPCM_TRLX_SET \ 230 | OR_GPCM_EHTR_SET \ 231 | OR_GPCM_EAD) 232 /* 0xFFFFE9F7 */ 233 234 /* 235 * Windows to access PIB via local bus 236 */ 237 /* PIB window base 0xF8008000 */ 238 #define CONFIG_SYS_PIB_BASE 0xF8008000 239 #define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024) 240 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PIB_BASE 241 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB) 242 243 /* 244 * CS2 on Local Bus, to PIB 245 */ 246 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_PIB_BASE \ 247 | BR_PS_8 \ 248 | BR_MS_GPCM \ 249 | BR_V) 250 /* 0xF8008801 */ 251 #define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 252 | OR_GPCM_XAM \ 253 | OR_GPCM_CSNT \ 254 | OR_GPCM_XACS \ 255 | OR_GPCM_SCY_15 \ 256 | OR_GPCM_TRLX_SET \ 257 | OR_GPCM_EHTR_SET \ 258 | OR_GPCM_EAD) 259 /* 0xffffe9f7 */ 260 261 /* 262 * CS3 on Local Bus, to PIB 263 */ 264 #define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIB_BASE + \ 265 CONFIG_SYS_PIB_WINDOW_SIZE) \ 266 | BR_PS_8 \ 267 | BR_MS_GPCM \ 268 | BR_V) 269 /* 0xF8010801 */ 270 #define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 271 | OR_GPCM_XAM \ 272 | OR_GPCM_CSNT \ 273 | OR_GPCM_XACS \ 274 | OR_GPCM_SCY_15 \ 275 | OR_GPCM_TRLX_SET \ 276 | OR_GPCM_EHTR_SET \ 277 | OR_GPCM_EAD) 278 /* 0xffffe9f7 */ 279 280 /* 281 * Serial Port 282 */ 283 #define CONFIG_SYS_NS16550_SERIAL 284 #define CONFIG_SYS_NS16550_REG_SIZE 1 285 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 286 287 #define CONFIG_SYS_BAUDRATE_TABLE \ 288 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 289 290 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 291 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 292 293 /* I2C */ 294 #define CONFIG_SYS_I2C 295 #define CONFIG_SYS_I2C_FSL 296 #define CONFIG_SYS_FSL_I2C_SPEED 400000 297 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 298 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 299 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } 300 301 /* 302 * Config on-board RTC 303 */ 304 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 305 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 306 307 /* 308 * General PCI 309 * Addresses are mapped 1-1. 310 */ 311 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 312 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 313 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 314 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 315 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 316 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 317 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 318 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 319 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 320 321 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 322 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 323 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 324 325 #ifdef CONFIG_PCI 326 #define CONFIG_PCI_INDIRECT_BRIDGE 327 328 #define CONFIG_83XX_PCI_STREAMING 329 330 #undef CONFIG_EEPRO100 331 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 332 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 333 334 #endif /* CONFIG_PCI */ 335 336 /* 337 * QE UEC ethernet configuration 338 */ 339 #define CONFIG_UEC_ETH 340 #define CONFIG_ETHPRIME "UEC0" 341 342 #define CONFIG_UEC_ETH1 /* ETH3 */ 343 344 #ifdef CONFIG_UEC_ETH1 345 #define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ 346 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 347 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 348 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 349 #define CONFIG_SYS_UEC1_PHY_ADDR 3 350 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 351 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 352 #endif 353 354 #define CONFIG_UEC_ETH2 /* ETH4 */ 355 356 #ifdef CONFIG_UEC_ETH2 357 #define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ 358 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 359 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 360 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 361 #define CONFIG_SYS_UEC2_PHY_ADDR 4 362 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 363 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 364 #endif 365 366 /* 367 * Environment 368 */ 369 #ifndef CONFIG_SYS_RAMBOOT 370 #define CONFIG_ENV_ADDR \ 371 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 372 #define CONFIG_ENV_SECT_SIZE 0x20000 373 #define CONFIG_ENV_SIZE 0x2000 374 #else 375 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 376 #define CONFIG_ENV_SIZE 0x2000 377 #endif 378 379 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 380 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 381 382 /* 383 * BOOTP options 384 */ 385 #define CONFIG_BOOTP_BOOTFILESIZE 386 387 /* 388 * Command line configuration. 389 */ 390 391 #undef CONFIG_WATCHDOG /* watchdog disabled */ 392 393 /* 394 * Miscellaneous configurable options 395 */ 396 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 397 398 /* 399 * For booting Linux, the board info and command line data 400 * have to be in the first 256 MB of memory, since this is 401 * the maximum mapped by the Linux kernel during initialization. 402 */ 403 /* Initial Memory map for Linux */ 404 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 405 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 406 407 /* 408 * Core HID Setup 409 */ 410 #define CONFIG_SYS_HID0_INIT 0x000000000 411 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 412 HID0_ENABLE_INSTRUCTION_CACHE) 413 #define CONFIG_SYS_HID2 HID2_HBE 414 415 /* 416 * MMU Setup 417 */ 418 419 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 420 421 /* DDR: cache cacheable */ 422 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 423 | BATL_PP_RW \ 424 | BATL_MEMCOHERENCE) 425 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 426 | BATU_BL_256M \ 427 | BATU_VS \ 428 | BATU_VP) 429 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 430 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 431 432 /* IMMRBAR & PCI IO: cache-inhibit and guarded */ 433 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ 434 | BATL_PP_RW \ 435 | BATL_CACHEINHIBIT \ 436 | BATL_GUARDEDSTORAGE) 437 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ 438 | BATU_BL_4M \ 439 | BATU_VS \ 440 | BATU_VP) 441 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 442 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 443 444 /* BCSR: cache-inhibit and guarded */ 445 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \ 446 | BATL_PP_RW \ 447 | BATL_CACHEINHIBIT \ 448 | BATL_GUARDEDSTORAGE) 449 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \ 450 | BATU_BL_128K \ 451 | BATU_VS \ 452 | BATU_VP) 453 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 454 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 455 456 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 457 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ 458 | BATL_PP_RW \ 459 | BATL_MEMCOHERENCE) 460 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ 461 | BATU_BL_32M \ 462 | BATU_VS \ 463 | BATU_VP) 464 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ 465 | BATL_PP_RW \ 466 | BATL_CACHEINHIBIT \ 467 | BATL_GUARDEDSTORAGE) 468 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 469 470 #define CONFIG_SYS_IBAT4L (0) 471 #define CONFIG_SYS_IBAT4U (0) 472 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 473 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 474 475 /* Stack in dcache: cacheable, no memory coherence */ 476 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 477 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ 478 | BATU_BL_128K \ 479 | BATU_VS \ 480 | BATU_VP) 481 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 482 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 483 484 #ifdef CONFIG_PCI 485 /* PCI MEM space: cacheable */ 486 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ 487 | BATL_PP_RW \ 488 | BATL_MEMCOHERENCE) 489 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ 490 | BATU_BL_256M \ 491 | BATU_VS \ 492 | BATU_VP) 493 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 494 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 495 /* PCI MMIO space: cache-inhibit and guarded */ 496 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ 497 | BATL_PP_RW \ 498 | BATL_CACHEINHIBIT \ 499 | BATL_GUARDEDSTORAGE) 500 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ 501 | BATU_BL_256M \ 502 | BATU_VS \ 503 | BATU_VP) 504 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 505 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 506 #else 507 #define CONFIG_SYS_IBAT6L (0) 508 #define CONFIG_SYS_IBAT6U (0) 509 #define CONFIG_SYS_IBAT7L (0) 510 #define CONFIG_SYS_IBAT7U (0) 511 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 512 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 513 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 514 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 515 #endif 516 517 #if defined(CONFIG_CMD_KGDB) 518 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 519 #endif 520 521 /* 522 * Environment Configuration 523 */ #define CONFIG_ENV_OVERWRITE 524 525 #if defined(CONFIG_UEC_ETH) 526 #define CONFIG_HAS_ETH0 527 #define CONFIG_HAS_ETH1 528 #endif 529 530 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 531 532 #define CONFIG_EXTRA_ENV_SETTINGS \ 533 "netdev=eth0\0" \ 534 "consoledev=ttyS0\0" \ 535 "ramdiskaddr=1000000\0" \ 536 "ramdiskfile=ramfs.83xx\0" \ 537 "fdtaddr=780000\0" \ 538 "fdtfile=mpc832x_mds.dtb\0" \ 539 "" 540 541 #define CONFIG_NFSBOOTCOMMAND \ 542 "setenv bootargs root=/dev/nfs rw " \ 543 "nfsroot=$serverip:$rootpath " \ 544 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 545 "$netdev:off " \ 546 "console=$consoledev,$baudrate $othbootargs;" \ 547 "tftp $loadaddr $bootfile;" \ 548 "tftp $fdtaddr $fdtfile;" \ 549 "bootm $loadaddr - $fdtaddr" 550 551 #define CONFIG_RAMBOOTCOMMAND \ 552 "setenv bootargs root=/dev/ram rw " \ 553 "console=$consoledev,$baudrate $othbootargs;" \ 554 "tftp $ramdiskaddr $ramdiskfile;" \ 555 "tftp $loadaddr $bootfile;" \ 556 "tftp $fdtaddr $fdtfile;" \ 557 "bootm $loadaddr $ramdiskaddr $fdtaddr" 558 559 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 560 561 #endif /* __CONFIG_H */ 562