1 /* 2 * Copyright (C) 2006 Freescale Semiconductor, Inc. 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation; either version 2 of 7 * the License, or (at your option) any later version. 8 * 9 * This program is distributed in the hope that it will be useful, 10 * but WITHOUT ANY WARRANTY; without even the implied warranty of 11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 12 * GNU General Public License for more details. 13 * 14 * You should have received a copy of the GNU General Public License 15 * along with this program; if not, write to the Free Software 16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 17 * MA 02111-1307 USA 18 */ 19 20 #ifndef __CONFIG_H 21 #define __CONFIG_H 22 23 /* 24 * High Level Configuration Options 25 */ 26 #define CONFIG_E300 1 /* E300 family */ 27 #define CONFIG_QE 1 /* Has QE */ 28 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 29 #define CONFIG_MPC832x 1 /* MPC832x CPU specific */ 30 #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ 31 32 #define CONFIG_SYS_TEXT_BASE 0xFE000000 33 34 /* 35 * System Clock Setup 36 */ 37 #ifdef CONFIG_PCISLAVE 38 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 39 #else 40 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 41 #endif 42 43 #ifndef CONFIG_SYS_CLK_FREQ 44 #define CONFIG_SYS_CLK_FREQ 66000000 45 #endif 46 47 /* 48 * Hardware Reset Configuration Word 49 */ 50 #define CONFIG_SYS_HRCW_LOW (\ 51 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 52 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 53 HRCWL_VCO_1X2 |\ 54 HRCWL_CSB_TO_CLKIN_2X1 |\ 55 HRCWL_CORE_TO_CSB_2X1 |\ 56 HRCWL_CE_PLL_VCO_DIV_2 |\ 57 HRCWL_CE_PLL_DIV_1X1 |\ 58 HRCWL_CE_TO_PLL_1X3) 59 60 #ifdef CONFIG_PCISLAVE 61 #define CONFIG_SYS_HRCW_HIGH (\ 62 HRCWH_PCI_AGENT |\ 63 HRCWH_PCI1_ARBITER_DISABLE |\ 64 HRCWH_CORE_ENABLE |\ 65 HRCWH_FROM_0XFFF00100 |\ 66 HRCWH_BOOTSEQ_DISABLE |\ 67 HRCWH_SW_WATCHDOG_DISABLE |\ 68 HRCWH_ROM_LOC_LOCAL_16BIT |\ 69 HRCWH_BIG_ENDIAN |\ 70 HRCWH_LALE_NORMAL) 71 #else 72 #define CONFIG_SYS_HRCW_HIGH (\ 73 HRCWH_PCI_HOST |\ 74 HRCWH_PCI1_ARBITER_ENABLE |\ 75 HRCWH_CORE_ENABLE |\ 76 HRCWH_FROM_0X00000100 |\ 77 HRCWH_BOOTSEQ_DISABLE |\ 78 HRCWH_SW_WATCHDOG_DISABLE |\ 79 HRCWH_ROM_LOC_LOCAL_16BIT |\ 80 HRCWH_BIG_ENDIAN |\ 81 HRCWH_LALE_NORMAL) 82 #endif 83 84 /* 85 * System IO Config 86 */ 87 #define CONFIG_SYS_SICRL 0x00000000 88 89 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 90 #define CONFIG_BOARD_EARLY_INIT_R 91 92 /* 93 * IMMR new address 94 */ 95 #define CONFIG_SYS_IMMR 0xE0000000 96 97 /* 98 * DDR Setup 99 */ 100 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 101 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 102 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 103 #define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ 104 105 #undef CONFIG_SPD_EEPROM 106 #if defined(CONFIG_SPD_EEPROM) 107 /* Determine DDR configuration from I2C interface 108 */ 109 #define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ 110 #else 111 /* Manually set up DDR parameters 112 */ 113 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 114 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 115 | CSCONFIG_AP \ 116 | CSCONFIG_ODT_WR_CFG \ 117 | CSCONFIG_ROW_BIT_13 \ 118 | CSCONFIG_COL_BIT_10) 119 /* 0x80840102 */ 120 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 121 | (0 << TIMING_CFG0_WRT_SHIFT) \ 122 | (0 << TIMING_CFG0_RRT_SHIFT) \ 123 | (0 << TIMING_CFG0_WWT_SHIFT) \ 124 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 125 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 126 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 127 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 128 /* 0x00220802 */ 129 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ 130 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 131 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ 132 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 133 | (13 << TIMING_CFG1_REFREC_SHIFT) \ 134 | (3 << TIMING_CFG1_WRREC_SHIFT) \ 135 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 136 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 137 /* 0x3935D322 */ 138 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 139 | (31 << TIMING_CFG2_CPO_SHIFT) \ 140 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 141 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 142 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 143 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 144 | (10 << TIMING_CFG2_FOUR_ACT_SHIFT)) 145 /* 0x0F9048CA */ 146 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 147 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 148 /* 0x02000000 */ 149 #define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ 150 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 151 /* 0x44400232 */ 152 #define CONFIG_SYS_DDR_MODE2 0x8000c000 153 #define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \ 154 | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 155 /* 0x03200064 */ 156 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 157 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 158 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 159 | SDRAM_CFG_32_BE) 160 /* 0x43080000 */ 161 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 162 #endif 163 164 /* 165 * Memory test 166 */ 167 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 168 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 169 #define CONFIG_SYS_MEMTEST_END 0x00100000 170 171 /* 172 * The reserved memory 173 */ 174 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 175 176 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 177 #define CONFIG_SYS_RAMBOOT 178 #else 179 #undef CONFIG_SYS_RAMBOOT 180 #endif 181 182 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 183 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 184 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 185 186 /* 187 * Initial RAM Base Address Setup 188 */ 189 #define CONFIG_SYS_INIT_RAM_LOCK 1 190 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM addr */ 191 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 192 #define CONFIG_SYS_GBL_DATA_OFFSET \ 193 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 194 195 /* 196 * Local Bus Configuration & Clock Setup 197 */ 198 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 199 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 200 #define CONFIG_SYS_LBC_LBCR 0x00000000 201 202 /* 203 * FLASH on the Local Bus 204 */ 205 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 206 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 207 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 208 #define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ 209 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 210 211 /* Window base at flash base */ 212 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 213 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 214 215 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 216 | BR_PS_16 /* 16 bit port */ \ 217 | BR_MS_GPCM /* MSEL = GPCM */ \ 218 | BR_V) /* valid */ 219 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 220 | OR_GPCM_XAM \ 221 | OR_GPCM_CSNT \ 222 | OR_GPCM_ACS_DIV2 \ 223 | OR_GPCM_XACS \ 224 | OR_GPCM_SCY_15 \ 225 | OR_GPCM_TRLX_SET \ 226 | OR_GPCM_EHTR_SET \ 227 | OR_GPCM_EAD) 228 /* 0xfe006ff7 */ 229 230 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 231 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 232 233 #undef CONFIG_SYS_FLASH_CHECKSUM 234 235 /* 236 * BCSR on the Local Bus 237 */ 238 #define CONFIG_SYS_BCSR 0xF8000000 239 /* Access window base at BCSR base */ 240 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 241 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 242 243 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 244 | BR_PS_8 \ 245 | BR_MS_GPCM \ 246 | BR_V) 247 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 248 | OR_GPCM_XAM \ 249 | OR_GPCM_CSNT \ 250 | OR_GPCM_XACS \ 251 | OR_GPCM_SCY_15 \ 252 | OR_GPCM_TRLX_SET \ 253 | OR_GPCM_EHTR_SET \ 254 | OR_GPCM_EAD) 255 /* 0xFFFFE9F7 */ 256 257 /* 258 * Windows to access PIB via local bus 259 */ 260 /* PIB window base 0xF8008000 */ 261 #define CONFIG_SYS_PIB_BASE 0xF8008000 262 #define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024) 263 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PIB_BASE 264 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB) 265 266 /* 267 * CS2 on Local Bus, to PIB 268 */ 269 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_PIB_BASE \ 270 | BR_PS_8 \ 271 | BR_MS_GPCM \ 272 | BR_V) 273 /* 0xF8008801 */ 274 #define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 275 | OR_GPCM_XAM \ 276 | OR_GPCM_CSNT \ 277 | OR_GPCM_XACS \ 278 | OR_GPCM_SCY_15 \ 279 | OR_GPCM_TRLX_SET \ 280 | OR_GPCM_EHTR_SET \ 281 | OR_GPCM_EAD) 282 /* 0xffffe9f7 */ 283 284 /* 285 * CS3 on Local Bus, to PIB 286 */ 287 #define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIB_BASE + \ 288 CONFIG_SYS_PIB_WINDOW_SIZE) \ 289 | BR_PS_8 \ 290 | BR_MS_GPCM \ 291 | BR_V) 292 /* 0xF8010801 */ 293 #define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 294 | OR_GPCM_XAM \ 295 | OR_GPCM_CSNT \ 296 | OR_GPCM_XACS \ 297 | OR_GPCM_SCY_15 \ 298 | OR_GPCM_TRLX_SET \ 299 | OR_GPCM_EHTR_SET \ 300 | OR_GPCM_EAD) 301 /* 0xffffe9f7 */ 302 303 /* 304 * Serial Port 305 */ 306 #define CONFIG_CONS_INDEX 1 307 #define CONFIG_SYS_NS16550 308 #define CONFIG_SYS_NS16550_SERIAL 309 #define CONFIG_SYS_NS16550_REG_SIZE 1 310 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 311 312 #define CONFIG_SYS_BAUDRATE_TABLE \ 313 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 314 315 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 316 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 317 318 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 319 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 320 /* Use the HUSH parser */ 321 #define CONFIG_SYS_HUSH_PARSER 322 #ifdef CONFIG_SYS_HUSH_PARSER 323 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 324 #endif 325 326 /* pass open firmware flat tree */ 327 #define CONFIG_OF_LIBFDT 1 328 #define CONFIG_OF_BOARD_SETUP 1 329 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 330 331 /* I2C */ 332 #define CONFIG_HARD_I2C /* I2C with hardware support */ 333 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 334 #define CONFIG_FSL_I2C 335 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 336 #define CONFIG_SYS_I2C_SLAVE 0x7F 337 #define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 338 #define CONFIG_SYS_I2C_OFFSET 0x3000 339 340 /* 341 * Config on-board RTC 342 */ 343 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 344 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 345 346 /* 347 * General PCI 348 * Addresses are mapped 1-1. 349 */ 350 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 351 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 352 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 353 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 354 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 355 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 356 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 357 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 358 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 359 360 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 361 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 362 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 363 364 365 #ifdef CONFIG_PCI 366 367 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 368 #define CONFIG_83XX_PCI_STREAMING 369 370 #undef CONFIG_EEPRO100 371 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 372 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 373 374 #endif /* CONFIG_PCI */ 375 376 /* 377 * QE UEC ethernet configuration 378 */ 379 #define CONFIG_UEC_ETH 380 #define CONFIG_ETHPRIME "UEC0" 381 382 #define CONFIG_UEC_ETH1 /* ETH3 */ 383 384 #ifdef CONFIG_UEC_ETH1 385 #define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ 386 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 387 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 388 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 389 #define CONFIG_SYS_UEC1_PHY_ADDR 3 390 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 391 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 392 #endif 393 394 #define CONFIG_UEC_ETH2 /* ETH4 */ 395 396 #ifdef CONFIG_UEC_ETH2 397 #define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ 398 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 399 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 400 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 401 #define CONFIG_SYS_UEC2_PHY_ADDR 4 402 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 403 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 404 #endif 405 406 /* 407 * Environment 408 */ 409 #ifndef CONFIG_SYS_RAMBOOT 410 #define CONFIG_ENV_IS_IN_FLASH 1 411 #define CONFIG_ENV_ADDR \ 412 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 413 #define CONFIG_ENV_SECT_SIZE 0x20000 414 #define CONFIG_ENV_SIZE 0x2000 415 #else 416 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 417 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 418 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 419 #define CONFIG_ENV_SIZE 0x2000 420 #endif 421 422 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 423 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 424 425 /* 426 * BOOTP options 427 */ 428 #define CONFIG_BOOTP_BOOTFILESIZE 429 #define CONFIG_BOOTP_BOOTPATH 430 #define CONFIG_BOOTP_GATEWAY 431 #define CONFIG_BOOTP_HOSTNAME 432 433 434 /* 435 * Command line configuration. 436 */ 437 #include <config_cmd_default.h> 438 439 #define CONFIG_CMD_PING 440 #define CONFIG_CMD_I2C 441 #define CONFIG_CMD_ASKENV 442 443 #if defined(CONFIG_PCI) 444 #define CONFIG_CMD_PCI 445 #endif 446 447 #if defined(CONFIG_SYS_RAMBOOT) 448 #undef CONFIG_CMD_SAVEENV 449 #undef CONFIG_CMD_LOADS 450 #endif 451 452 453 #undef CONFIG_WATCHDOG /* watchdog disabled */ 454 455 /* 456 * Miscellaneous configurable options 457 */ 458 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 459 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 460 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 461 462 #if defined(CONFIG_CMD_KGDB) 463 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 464 #else 465 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 466 #endif 467 468 /* Print Buffer Size */ 469 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 470 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 471 /* Boot Argument Buffer Size */ 472 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 473 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 474 475 /* 476 * For booting Linux, the board info and command line data 477 * have to be in the first 256 MB of memory, since this is 478 * the maximum mapped by the Linux kernel during initialization. 479 */ 480 /* Initial Memory map for Linux */ 481 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 482 483 /* 484 * Core HID Setup 485 */ 486 #define CONFIG_SYS_HID0_INIT 0x000000000 487 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 488 HID0_ENABLE_INSTRUCTION_CACHE) 489 #define CONFIG_SYS_HID2 HID2_HBE 490 491 /* 492 * MMU Setup 493 */ 494 495 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 496 497 /* DDR: cache cacheable */ 498 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 499 | BATL_PP_RW \ 500 | BATL_MEMCOHERENCE) 501 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 502 | BATU_BL_256M \ 503 | BATU_VS \ 504 | BATU_VP) 505 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 506 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 507 508 /* IMMRBAR & PCI IO: cache-inhibit and guarded */ 509 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ 510 | BATL_PP_RW \ 511 | BATL_CACHEINHIBIT \ 512 | BATL_GUARDEDSTORAGE) 513 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ 514 | BATU_BL_4M \ 515 | BATU_VS \ 516 | BATU_VP) 517 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 518 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 519 520 /* BCSR: cache-inhibit and guarded */ 521 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \ 522 | BATL_PP_RW \ 523 | BATL_CACHEINHIBIT \ 524 | BATL_GUARDEDSTORAGE) 525 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \ 526 | BATU_BL_128K \ 527 | BATU_VS \ 528 | BATU_VP) 529 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 530 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 531 532 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 533 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ 534 | BATL_PP_RW \ 535 | BATL_MEMCOHERENCE) 536 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ 537 | BATU_BL_32M \ 538 | BATU_VS \ 539 | BATU_VP) 540 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ 541 | BATL_PP_RW \ 542 | BATL_CACHEINHIBIT \ 543 | BATL_GUARDEDSTORAGE) 544 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 545 546 #define CONFIG_SYS_IBAT4L (0) 547 #define CONFIG_SYS_IBAT4U (0) 548 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 549 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 550 551 /* Stack in dcache: cacheable, no memory coherence */ 552 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 553 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ 554 | BATU_BL_128K \ 555 | BATU_VS \ 556 | BATU_VP) 557 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 558 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 559 560 #ifdef CONFIG_PCI 561 /* PCI MEM space: cacheable */ 562 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ 563 | BATL_PP_RW \ 564 | BATL_MEMCOHERENCE) 565 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ 566 | BATU_BL_256M \ 567 | BATU_VS \ 568 | BATU_VP) 569 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 570 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 571 /* PCI MMIO space: cache-inhibit and guarded */ 572 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ 573 | BATL_PP_RW \ 574 | BATL_CACHEINHIBIT \ 575 | BATL_GUARDEDSTORAGE) 576 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ 577 | BATU_BL_256M \ 578 | BATU_VS \ 579 | BATU_VP) 580 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 581 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 582 #else 583 #define CONFIG_SYS_IBAT6L (0) 584 #define CONFIG_SYS_IBAT6U (0) 585 #define CONFIG_SYS_IBAT7L (0) 586 #define CONFIG_SYS_IBAT7U (0) 587 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 588 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 589 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 590 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 591 #endif 592 593 #if defined(CONFIG_CMD_KGDB) 594 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 595 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 596 #endif 597 598 /* 599 * Environment Configuration 600 */ #define CONFIG_ENV_OVERWRITE 601 602 #if defined(CONFIG_UEC_ETH) 603 #define CONFIG_HAS_ETH0 604 #define CONFIG_HAS_ETH1 605 #endif 606 607 #define CONFIG_BAUDRATE 115200 608 609 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 610 611 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 612 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 613 614 #define CONFIG_EXTRA_ENV_SETTINGS \ 615 "netdev=eth0\0" \ 616 "consoledev=ttyS0\0" \ 617 "ramdiskaddr=1000000\0" \ 618 "ramdiskfile=ramfs.83xx\0" \ 619 "fdtaddr=780000\0" \ 620 "fdtfile=mpc832x_mds.dtb\0" \ 621 "" 622 623 #define CONFIG_NFSBOOTCOMMAND \ 624 "setenv bootargs root=/dev/nfs rw " \ 625 "nfsroot=$serverip:$rootpath " \ 626 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 627 "$netdev:off " \ 628 "console=$consoledev,$baudrate $othbootargs;" \ 629 "tftp $loadaddr $bootfile;" \ 630 "tftp $fdtaddr $fdtfile;" \ 631 "bootm $loadaddr - $fdtaddr" 632 633 #define CONFIG_RAMBOOTCOMMAND \ 634 "setenv bootargs root=/dev/ram rw " \ 635 "console=$consoledev,$baudrate $othbootargs;" \ 636 "tftp $ramdiskaddr $ramdiskfile;" \ 637 "tftp $loadaddr $bootfile;" \ 638 "tftp $fdtaddr $fdtfile;" \ 639 "bootm $loadaddr $ramdiskaddr $fdtaddr" 640 641 642 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 643 644 #endif /* __CONFIG_H */ 645