1 /* 2 * Copyright (C) 2006 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #ifndef __CONFIG_H 8 #define __CONFIG_H 9 10 /* 11 * High Level Configuration Options 12 */ 13 #define CONFIG_E300 1 /* E300 family */ 14 #define CONFIG_QE 1 /* Has QE */ 15 #define CONFIG_MPC832x 1 /* MPC832x CPU specific */ 16 #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ 17 18 /* 19 * System Clock Setup 20 */ 21 #ifdef CONFIG_PCISLAVE 22 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 23 #else 24 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 25 #endif 26 27 #ifndef CONFIG_SYS_CLK_FREQ 28 #define CONFIG_SYS_CLK_FREQ 66000000 29 #endif 30 31 /* 32 * Hardware Reset Configuration Word 33 */ 34 #define CONFIG_SYS_HRCW_LOW (\ 35 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 36 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 37 HRCWL_VCO_1X2 |\ 38 HRCWL_CSB_TO_CLKIN_2X1 |\ 39 HRCWL_CORE_TO_CSB_2X1 |\ 40 HRCWL_CE_PLL_VCO_DIV_2 |\ 41 HRCWL_CE_PLL_DIV_1X1 |\ 42 HRCWL_CE_TO_PLL_1X3) 43 44 #ifdef CONFIG_PCISLAVE 45 #define CONFIG_SYS_HRCW_HIGH (\ 46 HRCWH_PCI_AGENT |\ 47 HRCWH_PCI1_ARBITER_DISABLE |\ 48 HRCWH_CORE_ENABLE |\ 49 HRCWH_FROM_0XFFF00100 |\ 50 HRCWH_BOOTSEQ_DISABLE |\ 51 HRCWH_SW_WATCHDOG_DISABLE |\ 52 HRCWH_ROM_LOC_LOCAL_16BIT |\ 53 HRCWH_BIG_ENDIAN |\ 54 HRCWH_LALE_NORMAL) 55 #else 56 #define CONFIG_SYS_HRCW_HIGH (\ 57 HRCWH_PCI_HOST |\ 58 HRCWH_PCI1_ARBITER_ENABLE |\ 59 HRCWH_CORE_ENABLE |\ 60 HRCWH_FROM_0X00000100 |\ 61 HRCWH_BOOTSEQ_DISABLE |\ 62 HRCWH_SW_WATCHDOG_DISABLE |\ 63 HRCWH_ROM_LOC_LOCAL_16BIT |\ 64 HRCWH_BIG_ENDIAN |\ 65 HRCWH_LALE_NORMAL) 66 #endif 67 68 /* 69 * System IO Config 70 */ 71 #define CONFIG_SYS_SICRL 0x00000000 72 73 #define CONFIG_BOARD_EARLY_INIT_R 74 75 /* 76 * IMMR new address 77 */ 78 #define CONFIG_SYS_IMMR 0xE0000000 79 80 /* 81 * DDR Setup 82 */ 83 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 84 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 85 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 86 #define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ 87 88 #undef CONFIG_SPD_EEPROM 89 #if defined(CONFIG_SPD_EEPROM) 90 /* Determine DDR configuration from I2C interface 91 */ 92 #define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ 93 #else 94 /* Manually set up DDR parameters 95 */ 96 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 97 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 98 | CSCONFIG_AP \ 99 | CSCONFIG_ODT_WR_CFG \ 100 | CSCONFIG_ROW_BIT_13 \ 101 | CSCONFIG_COL_BIT_10) 102 /* 0x80840102 */ 103 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 104 | (0 << TIMING_CFG0_WRT_SHIFT) \ 105 | (0 << TIMING_CFG0_RRT_SHIFT) \ 106 | (0 << TIMING_CFG0_WWT_SHIFT) \ 107 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 108 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 109 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 110 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 111 /* 0x00220802 */ 112 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ 113 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 114 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ 115 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 116 | (13 << TIMING_CFG1_REFREC_SHIFT) \ 117 | (3 << TIMING_CFG1_WRREC_SHIFT) \ 118 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 119 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 120 /* 0x3935D322 */ 121 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ 122 | (31 << TIMING_CFG2_CPO_SHIFT) \ 123 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 124 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 125 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 126 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 127 | (10 << TIMING_CFG2_FOUR_ACT_SHIFT)) 128 /* 0x0F9048CA */ 129 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 130 #define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 131 /* 0x02000000 */ 132 #define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ 133 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 134 /* 0x44400232 */ 135 #define CONFIG_SYS_DDR_MODE2 0x8000c000 136 #define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \ 137 | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 138 /* 0x03200064 */ 139 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 140 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 141 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 142 | SDRAM_CFG_32_BE) 143 /* 0x43080000 */ 144 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 145 #endif 146 147 /* 148 * Memory test 149 */ 150 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 151 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 152 #define CONFIG_SYS_MEMTEST_END 0x00100000 153 154 /* 155 * The reserved memory 156 */ 157 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 158 159 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 160 #define CONFIG_SYS_RAMBOOT 161 #else 162 #undef CONFIG_SYS_RAMBOOT 163 #endif 164 165 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 166 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 167 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ 168 169 /* 170 * Initial RAM Base Address Setup 171 */ 172 #define CONFIG_SYS_INIT_RAM_LOCK 1 173 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM addr */ 174 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 175 #define CONFIG_SYS_GBL_DATA_OFFSET \ 176 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 177 178 /* 179 * Local Bus Configuration & Clock Setup 180 */ 181 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 182 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 183 #define CONFIG_SYS_LBC_LBCR 0x00000000 184 185 /* 186 * FLASH on the Local Bus 187 */ 188 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 189 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 190 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 191 #define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ 192 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 193 194 /* Window base at flash base */ 195 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 196 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) 197 198 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ 199 | BR_PS_16 /* 16 bit port */ \ 200 | BR_MS_GPCM /* MSEL = GPCM */ \ 201 | BR_V) /* valid */ 202 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 203 | OR_GPCM_XAM \ 204 | OR_GPCM_CSNT \ 205 | OR_GPCM_ACS_DIV2 \ 206 | OR_GPCM_XACS \ 207 | OR_GPCM_SCY_15 \ 208 | OR_GPCM_TRLX_SET \ 209 | OR_GPCM_EHTR_SET \ 210 | OR_GPCM_EAD) 211 /* 0xfe006ff7 */ 212 213 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 214 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 215 216 #undef CONFIG_SYS_FLASH_CHECKSUM 217 218 /* 219 * BCSR on the Local Bus 220 */ 221 #define CONFIG_SYS_BCSR 0xF8000000 222 /* Access window base at BCSR base */ 223 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR 224 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 225 226 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ 227 | BR_PS_8 \ 228 | BR_MS_GPCM \ 229 | BR_V) 230 #define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ 231 | OR_GPCM_XAM \ 232 | OR_GPCM_CSNT \ 233 | OR_GPCM_XACS \ 234 | OR_GPCM_SCY_15 \ 235 | OR_GPCM_TRLX_SET \ 236 | OR_GPCM_EHTR_SET \ 237 | OR_GPCM_EAD) 238 /* 0xFFFFE9F7 */ 239 240 /* 241 * Windows to access PIB via local bus 242 */ 243 /* PIB window base 0xF8008000 */ 244 #define CONFIG_SYS_PIB_BASE 0xF8008000 245 #define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024) 246 #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PIB_BASE 247 #define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB) 248 249 /* 250 * CS2 on Local Bus, to PIB 251 */ 252 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_PIB_BASE \ 253 | BR_PS_8 \ 254 | BR_MS_GPCM \ 255 | BR_V) 256 /* 0xF8008801 */ 257 #define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 258 | OR_GPCM_XAM \ 259 | OR_GPCM_CSNT \ 260 | OR_GPCM_XACS \ 261 | OR_GPCM_SCY_15 \ 262 | OR_GPCM_TRLX_SET \ 263 | OR_GPCM_EHTR_SET \ 264 | OR_GPCM_EAD) 265 /* 0xffffe9f7 */ 266 267 /* 268 * CS3 on Local Bus, to PIB 269 */ 270 #define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIB_BASE + \ 271 CONFIG_SYS_PIB_WINDOW_SIZE) \ 272 | BR_PS_8 \ 273 | BR_MS_GPCM \ 274 | BR_V) 275 /* 0xF8010801 */ 276 #define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ 277 | OR_GPCM_XAM \ 278 | OR_GPCM_CSNT \ 279 | OR_GPCM_XACS \ 280 | OR_GPCM_SCY_15 \ 281 | OR_GPCM_TRLX_SET \ 282 | OR_GPCM_EHTR_SET \ 283 | OR_GPCM_EAD) 284 /* 0xffffe9f7 */ 285 286 /* 287 * Serial Port 288 */ 289 #define CONFIG_CONS_INDEX 1 290 #define CONFIG_SYS_NS16550_SERIAL 291 #define CONFIG_SYS_NS16550_REG_SIZE 1 292 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 293 294 #define CONFIG_SYS_BAUDRATE_TABLE \ 295 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 296 297 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 298 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 299 300 /* I2C */ 301 #define CONFIG_SYS_I2C 302 #define CONFIG_SYS_I2C_FSL 303 #define CONFIG_SYS_FSL_I2C_SPEED 400000 304 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 305 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 306 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } 307 308 /* 309 * Config on-board RTC 310 */ 311 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 312 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 313 314 /* 315 * General PCI 316 * Addresses are mapped 1-1. 317 */ 318 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 319 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 320 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 321 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 322 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 323 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 324 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 325 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 326 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 327 328 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 329 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 330 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 331 332 #ifdef CONFIG_PCI 333 #define CONFIG_PCI_INDIRECT_BRIDGE 334 335 #define CONFIG_83XX_PCI_STREAMING 336 337 #undef CONFIG_EEPRO100 338 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 339 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 340 341 #endif /* CONFIG_PCI */ 342 343 /* 344 * QE UEC ethernet configuration 345 */ 346 #define CONFIG_UEC_ETH 347 #define CONFIG_ETHPRIME "UEC0" 348 349 #define CONFIG_UEC_ETH1 /* ETH3 */ 350 351 #ifdef CONFIG_UEC_ETH1 352 #define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ 353 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 354 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 355 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 356 #define CONFIG_SYS_UEC1_PHY_ADDR 3 357 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 358 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 359 #endif 360 361 #define CONFIG_UEC_ETH2 /* ETH4 */ 362 363 #ifdef CONFIG_UEC_ETH2 364 #define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ 365 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 366 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 367 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 368 #define CONFIG_SYS_UEC2_PHY_ADDR 4 369 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII 370 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 371 #endif 372 373 /* 374 * Environment 375 */ 376 #ifndef CONFIG_SYS_RAMBOOT 377 #define CONFIG_ENV_ADDR \ 378 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 379 #define CONFIG_ENV_SECT_SIZE 0x20000 380 #define CONFIG_ENV_SIZE 0x2000 381 #else 382 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 383 #define CONFIG_ENV_SIZE 0x2000 384 #endif 385 386 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 387 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 388 389 /* 390 * BOOTP options 391 */ 392 #define CONFIG_BOOTP_BOOTFILESIZE 393 394 /* 395 * Command line configuration. 396 */ 397 398 #undef CONFIG_WATCHDOG /* watchdog disabled */ 399 400 /* 401 * Miscellaneous configurable options 402 */ 403 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 404 405 /* 406 * For booting Linux, the board info and command line data 407 * have to be in the first 256 MB of memory, since this is 408 * the maximum mapped by the Linux kernel during initialization. 409 */ 410 /* Initial Memory map for Linux */ 411 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) 412 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 413 414 /* 415 * Core HID Setup 416 */ 417 #define CONFIG_SYS_HID0_INIT 0x000000000 418 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 419 HID0_ENABLE_INSTRUCTION_CACHE) 420 #define CONFIG_SYS_HID2 HID2_HBE 421 422 /* 423 * MMU Setup 424 */ 425 426 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 427 428 /* DDR: cache cacheable */ 429 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 430 | BATL_PP_RW \ 431 | BATL_MEMCOHERENCE) 432 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 433 | BATU_BL_256M \ 434 | BATU_VS \ 435 | BATU_VP) 436 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 437 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 438 439 /* IMMRBAR & PCI IO: cache-inhibit and guarded */ 440 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ 441 | BATL_PP_RW \ 442 | BATL_CACHEINHIBIT \ 443 | BATL_GUARDEDSTORAGE) 444 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ 445 | BATU_BL_4M \ 446 | BATU_VS \ 447 | BATU_VP) 448 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 449 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 450 451 /* BCSR: cache-inhibit and guarded */ 452 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \ 453 | BATL_PP_RW \ 454 | BATL_CACHEINHIBIT \ 455 | BATL_GUARDEDSTORAGE) 456 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \ 457 | BATU_BL_128K \ 458 | BATU_VS \ 459 | BATU_VP) 460 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 461 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 462 463 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 464 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ 465 | BATL_PP_RW \ 466 | BATL_MEMCOHERENCE) 467 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ 468 | BATU_BL_32M \ 469 | BATU_VS \ 470 | BATU_VP) 471 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ 472 | BATL_PP_RW \ 473 | BATL_CACHEINHIBIT \ 474 | BATL_GUARDEDSTORAGE) 475 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 476 477 #define CONFIG_SYS_IBAT4L (0) 478 #define CONFIG_SYS_IBAT4U (0) 479 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 480 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 481 482 /* Stack in dcache: cacheable, no memory coherence */ 483 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 484 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ 485 | BATU_BL_128K \ 486 | BATU_VS \ 487 | BATU_VP) 488 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 489 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 490 491 #ifdef CONFIG_PCI 492 /* PCI MEM space: cacheable */ 493 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ 494 | BATL_PP_RW \ 495 | BATL_MEMCOHERENCE) 496 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ 497 | BATU_BL_256M \ 498 | BATU_VS \ 499 | BATU_VP) 500 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 501 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 502 /* PCI MMIO space: cache-inhibit and guarded */ 503 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ 504 | BATL_PP_RW \ 505 | BATL_CACHEINHIBIT \ 506 | BATL_GUARDEDSTORAGE) 507 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ 508 | BATU_BL_256M \ 509 | BATU_VS \ 510 | BATU_VP) 511 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 512 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 513 #else 514 #define CONFIG_SYS_IBAT6L (0) 515 #define CONFIG_SYS_IBAT6U (0) 516 #define CONFIG_SYS_IBAT7L (0) 517 #define CONFIG_SYS_IBAT7U (0) 518 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 519 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 520 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 521 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 522 #endif 523 524 #if defined(CONFIG_CMD_KGDB) 525 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 526 #endif 527 528 /* 529 * Environment Configuration 530 */ #define CONFIG_ENV_OVERWRITE 531 532 #if defined(CONFIG_UEC_ETH) 533 #define CONFIG_HAS_ETH0 534 #define CONFIG_HAS_ETH1 535 #endif 536 537 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 538 539 #define CONFIG_EXTRA_ENV_SETTINGS \ 540 "netdev=eth0\0" \ 541 "consoledev=ttyS0\0" \ 542 "ramdiskaddr=1000000\0" \ 543 "ramdiskfile=ramfs.83xx\0" \ 544 "fdtaddr=780000\0" \ 545 "fdtfile=mpc832x_mds.dtb\0" \ 546 "" 547 548 #define CONFIG_NFSBOOTCOMMAND \ 549 "setenv bootargs root=/dev/nfs rw " \ 550 "nfsroot=$serverip:$rootpath " \ 551 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 552 "$netdev:off " \ 553 "console=$consoledev,$baudrate $othbootargs;" \ 554 "tftp $loadaddr $bootfile;" \ 555 "tftp $fdtaddr $fdtfile;" \ 556 "bootm $loadaddr - $fdtaddr" 557 558 #define CONFIG_RAMBOOTCOMMAND \ 559 "setenv bootargs root=/dev/ram rw " \ 560 "console=$consoledev,$baudrate $othbootargs;" \ 561 "tftp $ramdiskaddr $ramdiskfile;" \ 562 "tftp $loadaddr $bootfile;" \ 563 "tftp $fdtaddr $fdtfile;" \ 564 "bootm $loadaddr $ramdiskaddr $fdtaddr" 565 566 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 567 568 #endif /* __CONFIG_H */ 569