1 /* 2 * Copyright (C) 2006 Freescale Semiconductor, Inc. 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation; either version 2 of 7 * the License, or (at your option) any later version. 8 * 9 * This program is distributed in the hope that it will be useful, 10 * but WITHOUT ANY WARRANTY; without even the implied warranty of 11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 12 * GNU General Public License for more details. 13 * 14 * You should have received a copy of the GNU General Public License 15 * along with this program; if not, write to the Free Software 16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 17 * MA 02111-1307 USA 18 */ 19 20 #ifndef __CONFIG_H 21 #define __CONFIG_H 22 23 #undef DEBUG 24 25 /* 26 * High Level Configuration Options 27 */ 28 #define CONFIG_E300 1 /* E300 family */ 29 #define CONFIG_QE 1 /* Has QE */ 30 #define CONFIG_MPC83XX 1 /* MPC83xx family */ 31 #define CONFIG_MPC832X 1 /* MPC832x CPU specific */ 32 #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ 33 #undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */ 34 #undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */ 35 36 /* 37 * System Clock Setup 38 */ 39 #ifdef CONFIG_PCISLAVE 40 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 41 #else 42 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 43 #endif 44 45 #ifndef CONFIG_SYS_CLK_FREQ 46 #define CONFIG_SYS_CLK_FREQ 66000000 47 #endif 48 49 /* 50 * Hardware Reset Configuration Word 51 */ 52 #define CFG_HRCW_LOW (\ 53 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 54 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 55 HRCWL_VCO_1X2 |\ 56 HRCWL_CSB_TO_CLKIN_2X1 |\ 57 HRCWL_CORE_TO_CSB_2X1 |\ 58 HRCWL_CE_PLL_VCO_DIV_2 |\ 59 HRCWL_CE_PLL_DIV_1X1 |\ 60 HRCWL_CE_TO_PLL_1X3) 61 62 #ifdef CONFIG_PCISLAVE 63 #define CFG_HRCW_HIGH (\ 64 HRCWH_PCI_AGENT |\ 65 HRCWH_PCI1_ARBITER_DISABLE |\ 66 HRCWH_CORE_ENABLE |\ 67 HRCWH_FROM_0XFFF00100 |\ 68 HRCWH_BOOTSEQ_DISABLE |\ 69 HRCWH_SW_WATCHDOG_DISABLE |\ 70 HRCWH_ROM_LOC_LOCAL_16BIT |\ 71 HRCWH_BIG_ENDIAN |\ 72 HRCWH_LALE_NORMAL) 73 #else 74 #define CFG_HRCW_HIGH (\ 75 HRCWH_PCI_HOST |\ 76 HRCWH_PCI1_ARBITER_ENABLE |\ 77 HRCWH_CORE_ENABLE |\ 78 HRCWH_FROM_0X00000100 |\ 79 HRCWH_BOOTSEQ_DISABLE |\ 80 HRCWH_SW_WATCHDOG_DISABLE |\ 81 HRCWH_ROM_LOC_LOCAL_16BIT |\ 82 HRCWH_BIG_ENDIAN |\ 83 HRCWH_LALE_NORMAL) 84 #endif 85 86 /* 87 * System IO Config 88 */ 89 #define CFG_SICRL 0x00000000 90 91 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 92 #define CONFIG_BOARD_EARLY_INIT_R 93 94 /* 95 * IMMR new address 96 */ 97 #define CFG_IMMR 0xE0000000 98 99 /* 100 * DDR Setup 101 */ 102 #define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ 103 #define CFG_SDRAM_BASE CFG_DDR_BASE 104 #define CFG_DDR_SDRAM_BASE CFG_DDR_BASE 105 #define CFG_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ 106 107 #undef CONFIG_SPD_EEPROM 108 #if defined(CONFIG_SPD_EEPROM) 109 /* Determine DDR configuration from I2C interface 110 */ 111 #define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ 112 #else 113 /* Manually set up DDR parameters 114 */ 115 #define CFG_DDR_SIZE 128 /* MB */ 116 #define CFG_DDR_CS0_CONFIG 0x80840102 117 #define CFG_DDR_TIMING_0 0x00220802 118 #define CFG_DDR_TIMING_1 0x3935d322 119 #define CFG_DDR_TIMING_2 0x0f9048ca 120 #define CFG_DDR_TIMING_3 0x00000000 121 #define CFG_DDR_CLK_CNTL 0x02000000 122 #define CFG_DDR_MODE 0x44400232 123 #define CFG_DDR_MODE2 0x8000c000 124 #define CFG_DDR_INTERVAL 0x03200064 125 #define CFG_DDR_CS0_BNDS 0x00000007 126 #define CFG_DDR_SDRAM_CFG 0x43080000 127 #define CFG_DDR_SDRAM_CFG2 0x00401000 128 #endif 129 130 /* 131 * Memory test 132 */ 133 #undef CFG_DRAM_TEST /* memory test, takes time */ 134 #define CFG_MEMTEST_START 0x00000000 /* memtest region */ 135 #define CFG_MEMTEST_END 0x00100000 136 137 /* 138 * The reserved memory 139 */ 140 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ 141 142 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) 143 #define CFG_RAMBOOT 144 #else 145 #undef CFG_RAMBOOT 146 #endif 147 148 /* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ 149 #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 150 #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 151 152 /* 153 * Initial RAM Base Address Setup 154 */ 155 #define CFG_INIT_RAM_LOCK 1 156 #define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 157 #define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ 158 #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ 159 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 160 161 /* 162 * Local Bus Configuration & Clock Setup 163 */ 164 #define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) 165 #define CFG_LBC_LBCR 0x00000000 166 167 /* 168 * FLASH on the Local Bus 169 */ 170 #define CFG_FLASH_CFI /* use the Common Flash Interface */ 171 #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ 172 #define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ 173 #define CFG_FLASH_SIZE 16 /* FLASH size is 16M */ 174 175 #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ 176 #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ 177 178 #define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ 179 (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ 180 BR_V) /* valid */ 181 #define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ 182 183 #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ 184 #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ 185 186 #undef CFG_FLASH_CHECKSUM 187 188 /* 189 * BCSR on the Local Bus 190 */ 191 #define CFG_BCSR 0xF8000000 192 #define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ 193 #define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ 194 195 #define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ 196 #define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ 197 198 /* 199 * SDRAM on the Local Bus 200 */ 201 #undef CFG_LB_SDRAM /* The board has not SRDAM on local bus */ 202 203 #ifdef CFG_LB_SDRAM 204 #define CFG_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ 205 #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 206 207 #define CFG_LBLAWBAR2_PRELIM CFG_LBC_SDRAM_BASE 208 #define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ 209 210 /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ 211 /* 212 * Base Register 2 and Option Register 2 configure SDRAM. 213 * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. 214 * 215 * For BR2, need: 216 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 217 * port size = 32-bits = BR2[19:20] = 11 218 * no parity checking = BR2[21:22] = 00 219 * SDRAM for MSEL = BR2[24:26] = 011 220 * Valid = BR[31] = 1 221 * 222 * 0 4 8 12 16 20 24 28 223 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 224 * 225 * CFG_LBC_SDRAM_BASE should be masked and OR'ed into 226 * the top 17 bits of BR2. 227 */ 228 229 #define CFG_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ 230 231 /* 232 * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. 233 * 234 * For OR2, need: 235 * 64MB mask for AM, OR2[0:7] = 1111 1100 236 * XAM, OR2[17:18] = 11 237 * 9 columns OR2[19-21] = 010 238 * 13 rows OR2[23-25] = 100 239 * EAD set for extra time OR[31] = 1 240 * 241 * 0 4 8 12 16 20 24 28 242 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 243 */ 244 245 #define CFG_OR2_PRELIM 0xfc006901 246 247 #define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ 248 #define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ 249 250 /* 251 * LSDMR masks 252 */ 253 #define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) 254 #define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) 255 #define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) 256 #define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) 257 #define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) 258 #define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) 259 #define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) 260 #define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) 261 262 #define CFG_LBC_LSDMR_COMMON 0x0063b723 263 264 /* 265 * SDRAM Controller configuration sequence. 266 */ 267 #define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ 268 | CFG_LBC_LSDMR_OP_PCHALL) 269 #define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ 270 | CFG_LBC_LSDMR_OP_ARFRSH) 271 #define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ 272 | CFG_LBC_LSDMR_OP_ARFRSH) 273 #define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ 274 | CFG_LBC_LSDMR_OP_MRW) 275 #define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ 276 | CFG_LBC_LSDMR_OP_NORMAL) 277 278 #endif 279 280 /* 281 * Windows to access PIB via local bus 282 */ 283 #define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ 284 #define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ 285 286 /* 287 * CS2 on Local Bus, to PIB 288 */ 289 #define CFG_BR2_PRELIM 0xf8008801 /* CS2 base address at 0xf8008000 */ 290 #define CFG_OR2_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ 291 292 /* 293 * CS3 on Local Bus, to PIB 294 */ 295 #define CFG_BR3_PRELIM 0xf8010801 /* CS3 base address at 0xf8010000 */ 296 #define CFG_OR3_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ 297 298 /* 299 * Serial Port 300 */ 301 #define CONFIG_CONS_INDEX 1 302 #undef CONFIG_SERIAL_SOFTWARE_FIFO 303 #define CFG_NS16550 304 #define CFG_NS16550_SERIAL 305 #define CFG_NS16550_REG_SIZE 1 306 #define CFG_NS16550_CLK get_bus_freq(0) 307 308 #define CFG_BAUDRATE_TABLE \ 309 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 310 311 #define CFG_NS16550_COM1 (CFG_IMMR+0x4500) 312 #define CFG_NS16550_COM2 (CFG_IMMR+0x4600) 313 314 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 315 /* Use the HUSH parser */ 316 #define CFG_HUSH_PARSER 317 #ifdef CFG_HUSH_PARSER 318 #define CFG_PROMPT_HUSH_PS2 "> " 319 #endif 320 321 /* pass open firmware flat tree */ 322 #define CONFIG_OF_LIBFDT 1 323 #define CONFIG_OF_BOARD_SETUP 1 324 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 325 326 /* I2C */ 327 #define CONFIG_HARD_I2C /* I2C with hardware support */ 328 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 329 #define CONFIG_FSL_I2C 330 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ 331 #define CFG_I2C_SLAVE 0x7F 332 #define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 333 #define CFG_I2C_OFFSET 0x3000 334 335 /* 336 * Config on-board RTC 337 */ 338 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 339 #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 340 341 /* 342 * General PCI 343 * Addresses are mapped 1-1. 344 */ 345 #define CFG_PCI_MEM_BASE 0x80000000 346 #define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE 347 #define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ 348 #define CFG_PCI_MMIO_BASE 0x90000000 349 #define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE 350 #define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ 351 #define CFG_PCI_IO_BASE 0xE0300000 352 #define CFG_PCI_IO_PHYS 0xE0300000 353 #define CFG_PCI_IO_SIZE 0x100000 /* 1M */ 354 355 #define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE 356 #define CFG_PCI_SLV_MEM_BUS 0x00000000 357 #define CFG_PCI_SLV_MEM_SIZE 0x80000000 358 359 360 #ifdef CONFIG_PCI 361 362 #define CONFIG_NET_MULTI 363 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 364 365 #undef CONFIG_EEPRO100 366 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 367 #define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 368 369 #endif /* CONFIG_PCI */ 370 371 372 #ifndef CONFIG_NET_MULTI 373 #define CONFIG_NET_MULTI 1 374 #endif 375 376 /* 377 * QE UEC ethernet configuration 378 */ 379 #define CONFIG_UEC_ETH 380 #define CONFIG_ETHPRIME "Freescale GETH" 381 382 #define CONFIG_UEC_ETH1 /* ETH3 */ 383 384 #ifdef CONFIG_UEC_ETH1 385 #define CFG_UEC1_UCC_NUM 2 /* UCC3 */ 386 #define CFG_UEC1_RX_CLK QE_CLK9 387 #define CFG_UEC1_TX_CLK QE_CLK10 388 #define CFG_UEC1_ETH_TYPE FAST_ETH 389 #define CFG_UEC1_PHY_ADDR 3 390 #define CFG_UEC1_INTERFACE_MODE ENET_100_MII 391 #endif 392 393 #define CONFIG_UEC_ETH2 /* ETH4 */ 394 395 #ifdef CONFIG_UEC_ETH2 396 #define CFG_UEC2_UCC_NUM 3 /* UCC4 */ 397 #define CFG_UEC2_RX_CLK QE_CLK7 398 #define CFG_UEC2_TX_CLK QE_CLK8 399 #define CFG_UEC2_ETH_TYPE FAST_ETH 400 #define CFG_UEC2_PHY_ADDR 4 401 #define CFG_UEC2_INTERFACE_MODE ENET_100_MII 402 #endif 403 404 /* 405 * Environment 406 */ 407 #ifndef CFG_RAMBOOT 408 #define CFG_ENV_IS_IN_FLASH 1 409 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) 410 #define CFG_ENV_SECT_SIZE 0x20000 411 #define CFG_ENV_SIZE 0x2000 412 #else 413 #define CFG_NO_FLASH 1 /* Flash is not usable now */ 414 #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 415 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) 416 #define CFG_ENV_SIZE 0x2000 417 #endif 418 419 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 420 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 421 422 /* 423 * BOOTP options 424 */ 425 #define CONFIG_BOOTP_BOOTFILESIZE 426 #define CONFIG_BOOTP_BOOTPATH 427 #define CONFIG_BOOTP_GATEWAY 428 #define CONFIG_BOOTP_HOSTNAME 429 430 431 /* 432 * Command line configuration. 433 */ 434 #include <config_cmd_default.h> 435 436 #define CONFIG_CMD_PING 437 #define CONFIG_CMD_I2C 438 #define CONFIG_CMD_ASKENV 439 440 #if defined(CONFIG_PCI) 441 #define CONFIG_CMD_PCI 442 #endif 443 444 #if defined(CFG_RAMBOOT) 445 #undef CONFIG_CMD_ENV 446 #undef CONFIG_CMD_LOADS 447 #endif 448 449 450 #undef CONFIG_WATCHDOG /* watchdog disabled */ 451 452 /* 453 * Miscellaneous configurable options 454 */ 455 #define CFG_LONGHELP /* undef to save memory */ 456 #define CFG_LOAD_ADDR 0x2000000 /* default load address */ 457 #define CFG_PROMPT "=> " /* Monitor Command Prompt */ 458 459 #if defined(CONFIG_CMD_KGDB) 460 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ 461 #else 462 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 463 #endif 464 465 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 466 #define CFG_MAXARGS 16 /* max number of command args */ 467 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 468 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ 469 470 /* 471 * For booting Linux, the board info and command line data 472 * have to be in the first 8 MB of memory, since this is 473 * the maximum mapped by the Linux kernel during initialization. 474 */ 475 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 476 477 /* 478 * Core HID Setup 479 */ 480 #define CFG_HID0_INIT 0x000000000 481 #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK 482 #define CFG_HID2 HID2_HBE 483 484 /* 485 * MMU Setup 486 */ 487 488 /* DDR: cache cacheable */ 489 #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 490 #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 491 #define CFG_DBAT0L CFG_IBAT0L 492 #define CFG_DBAT0U CFG_IBAT0U 493 494 /* IMMRBAR & PCI IO: cache-inhibit and guarded */ 495 #define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ 496 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 497 #define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) 498 #define CFG_DBAT1L CFG_IBAT1L 499 #define CFG_DBAT1U CFG_IBAT1U 500 501 /* BCSR: cache-inhibit and guarded */ 502 #define CFG_IBAT2L (CFG_BCSR | BATL_PP_10 | \ 503 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 504 #define CFG_IBAT2U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) 505 #define CFG_DBAT2L CFG_IBAT2L 506 #define CFG_DBAT2U CFG_IBAT2U 507 508 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 509 #define CFG_IBAT3L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 510 #define CFG_IBAT3U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) 511 #define CFG_DBAT3L (CFG_FLASH_BASE | BATL_PP_10 | \ 512 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 513 #define CFG_DBAT3U CFG_IBAT3U 514 515 #define CFG_IBAT4L (0) 516 #define CFG_IBAT4U (0) 517 #define CFG_DBAT4L CFG_IBAT4L 518 #define CFG_DBAT4U CFG_IBAT4U 519 520 /* Stack in dcache: cacheable, no memory coherence */ 521 #define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) 522 #define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 523 #define CFG_DBAT5L CFG_IBAT5L 524 #define CFG_DBAT5U CFG_IBAT5U 525 526 #ifdef CONFIG_PCI 527 /* PCI MEM space: cacheable */ 528 #define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) 529 #define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 530 #define CFG_DBAT6L CFG_IBAT6L 531 #define CFG_DBAT6U CFG_IBAT6U 532 /* PCI MMIO space: cache-inhibit and guarded */ 533 #define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ 534 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 535 #define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 536 #define CFG_DBAT7L CFG_IBAT7L 537 #define CFG_DBAT7U CFG_IBAT7U 538 #else 539 #define CFG_IBAT6L (0) 540 #define CFG_IBAT6U (0) 541 #define CFG_IBAT7L (0) 542 #define CFG_IBAT7U (0) 543 #define CFG_DBAT6L CFG_IBAT6L 544 #define CFG_DBAT6U CFG_IBAT6U 545 #define CFG_DBAT7L CFG_IBAT7L 546 #define CFG_DBAT7U CFG_IBAT7U 547 #endif 548 549 /* 550 * Internal Definitions 551 * 552 * Boot Flags 553 */ 554 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 555 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 556 557 #if defined(CONFIG_CMD_KGDB) 558 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 559 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 560 #endif 561 562 /* 563 * Environment Configuration 564 */ 565 566 #define CONFIG_ENV_OVERWRITE 567 568 #if defined(CONFIG_UEC_ETH) 569 #define CONFIG_HAS_ETH0 570 #define CONFIG_ETHADDR 00:04:9f:ef:03:01 571 #define CONFIG_HAS_ETH1 572 #define CONFIG_ETH1ADDR 00:04:9f:ef:03:02 573 #endif 574 575 #define CONFIG_BAUDRATE 115200 576 577 #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ 578 579 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 580 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 581 582 #define CONFIG_EXTRA_ENV_SETTINGS \ 583 "netdev=eth0\0" \ 584 "consoledev=ttyS0\0" \ 585 "ramdiskaddr=1000000\0" \ 586 "ramdiskfile=ramfs.83xx\0" \ 587 "fdtaddr=400000\0" \ 588 "fdtfile=mpc832xemds.dtb\0" \ 589 "" 590 591 #define CONFIG_NFSBOOTCOMMAND \ 592 "setenv bootargs root=/dev/nfs rw " \ 593 "nfsroot=$serverip:$rootpath " \ 594 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 595 "console=$consoledev,$baudrate $othbootargs;" \ 596 "tftp $loadaddr $bootfile;" \ 597 "tftp $fdtaddr $fdtfile;" \ 598 "bootm $loadaddr - $fdtaddr" 599 600 #define CONFIG_RAMBOOTCOMMAND \ 601 "setenv bootargs root=/dev/ram rw " \ 602 "console=$consoledev,$baudrate $othbootargs;" \ 603 "tftp $ramdiskaddr $ramdiskfile;" \ 604 "tftp $loadaddr $bootfile;" \ 605 "tftp $fdtaddr $fdtfile;" \ 606 "bootm $loadaddr $ramdiskaddr $fdtaddr" 607 608 609 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 610 611 #endif /* __CONFIG_H */ 612