1 /* 2 * Copyright (C) 2006 Freescale Semiconductor, Inc. 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License as 6 * published by the Free Software Foundation; either version 2 of 7 * the License, or (at your option) any later version. 8 * 9 * This program is distributed in the hope that it will be useful, 10 * but WITHOUT ANY WARRANTY; without even the implied warranty of 11 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 12 * GNU General Public License for more details. 13 * 14 * You should have received a copy of the GNU General Public License 15 * along with this program; if not, write to the Free Software 16 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 17 * MA 02111-1307 USA 18 */ 19 20 #ifndef __CONFIG_H 21 #define __CONFIG_H 22 23 /* 24 * High Level Configuration Options 25 */ 26 #define CONFIG_E300 1 /* E300 family */ 27 #define CONFIG_QE 1 /* Has QE */ 28 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 29 #define CONFIG_MPC832x 1 /* MPC832x CPU specific */ 30 #define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ 31 32 #define CONFIG_SYS_TEXT_BASE 0xFE000000 33 34 /* 35 * System Clock Setup 36 */ 37 #ifdef CONFIG_PCISLAVE 38 #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ 39 #else 40 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 41 #endif 42 43 #ifndef CONFIG_SYS_CLK_FREQ 44 #define CONFIG_SYS_CLK_FREQ 66000000 45 #endif 46 47 /* 48 * Hardware Reset Configuration Word 49 */ 50 #define CONFIG_SYS_HRCW_LOW (\ 51 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 52 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 53 HRCWL_VCO_1X2 |\ 54 HRCWL_CSB_TO_CLKIN_2X1 |\ 55 HRCWL_CORE_TO_CSB_2X1 |\ 56 HRCWL_CE_PLL_VCO_DIV_2 |\ 57 HRCWL_CE_PLL_DIV_1X1 |\ 58 HRCWL_CE_TO_PLL_1X3) 59 60 #ifdef CONFIG_PCISLAVE 61 #define CONFIG_SYS_HRCW_HIGH (\ 62 HRCWH_PCI_AGENT |\ 63 HRCWH_PCI1_ARBITER_DISABLE |\ 64 HRCWH_CORE_ENABLE |\ 65 HRCWH_FROM_0XFFF00100 |\ 66 HRCWH_BOOTSEQ_DISABLE |\ 67 HRCWH_SW_WATCHDOG_DISABLE |\ 68 HRCWH_ROM_LOC_LOCAL_16BIT |\ 69 HRCWH_BIG_ENDIAN |\ 70 HRCWH_LALE_NORMAL) 71 #else 72 #define CONFIG_SYS_HRCW_HIGH (\ 73 HRCWH_PCI_HOST |\ 74 HRCWH_PCI1_ARBITER_ENABLE |\ 75 HRCWH_CORE_ENABLE |\ 76 HRCWH_FROM_0X00000100 |\ 77 HRCWH_BOOTSEQ_DISABLE |\ 78 HRCWH_SW_WATCHDOG_DISABLE |\ 79 HRCWH_ROM_LOC_LOCAL_16BIT |\ 80 HRCWH_BIG_ENDIAN |\ 81 HRCWH_LALE_NORMAL) 82 #endif 83 84 /* 85 * System IO Config 86 */ 87 #define CONFIG_SYS_SICRL 0x00000000 88 89 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 90 #define CONFIG_BOARD_EARLY_INIT_R 91 92 /* 93 * IMMR new address 94 */ 95 #define CONFIG_SYS_IMMR 0xE0000000 96 97 /* 98 * DDR Setup 99 */ 100 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 101 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 102 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 103 #define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ 104 105 #undef CONFIG_SPD_EEPROM 106 #if defined(CONFIG_SPD_EEPROM) 107 /* Determine DDR configuration from I2C interface 108 */ 109 #define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ 110 #else 111 /* Manually set up DDR parameters 112 */ 113 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 114 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80840102 115 #define CONFIG_SYS_DDR_TIMING_0 0x00220802 116 #define CONFIG_SYS_DDR_TIMING_1 0x3935d322 117 #define CONFIG_SYS_DDR_TIMING_2 0x0f9048ca 118 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 119 #define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 120 #define CONFIG_SYS_DDR_MODE 0x44400232 121 #define CONFIG_SYS_DDR_MODE2 0x8000c000 122 #define CONFIG_SYS_DDR_INTERVAL 0x03200064 123 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 124 #define CONFIG_SYS_DDR_SDRAM_CFG 0x43080000 125 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 126 #endif 127 128 /* 129 * Memory test 130 */ 131 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 132 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 133 #define CONFIG_SYS_MEMTEST_END 0x00100000 134 135 /* 136 * The reserved memory 137 */ 138 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 139 140 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 141 #define CONFIG_SYS_RAMBOOT 142 #else 143 #undef CONFIG_SYS_RAMBOOT 144 #endif 145 146 /* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ 147 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 148 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ 149 150 /* 151 * Initial RAM Base Address Setup 152 */ 153 #define CONFIG_SYS_INIT_RAM_LOCK 1 154 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 155 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 156 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 157 158 /* 159 * Local Bus Configuration & Clock Setup 160 */ 161 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 162 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 163 #define CONFIG_SYS_LBC_LBCR 0x00000000 164 165 /* 166 * FLASH on the Local Bus 167 */ 168 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 169 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 170 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 171 #define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ 172 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 173 174 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ 175 #define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ 176 177 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \ 178 (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ 179 BR_V) /* valid */ 180 #define CONFIG_SYS_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */ 181 182 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 183 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 184 185 #undef CONFIG_SYS_FLASH_CHECKSUM 186 187 /* 188 * BCSR on the Local Bus 189 */ 190 #define CONFIG_SYS_BCSR 0xF8000000 191 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR /* Access window base at BCSR base */ 192 #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ 193 194 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */ 195 #define CONFIG_SYS_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ 196 197 /* 198 * SDRAM on the Local Bus 199 */ 200 #undef CONFIG_SYS_LB_SDRAM /* The board has not SRDAM on local bus */ 201 202 #ifdef CONFIG_SYS_LB_SDRAM 203 #define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ 204 #define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ 205 206 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_LBC_SDRAM_BASE 207 #define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000019 /* 64MB */ 208 209 /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ 210 /* 211 * Base Register 2 and Option Register 2 configure SDRAM. 212 * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. 213 * 214 * For BR2, need: 215 * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 216 * port size = 32-bits = BR2[19:20] = 11 217 * no parity checking = BR2[21:22] = 00 218 * SDRAM for MSEL = BR2[24:26] = 011 219 * Valid = BR[31] = 1 220 * 221 * 0 4 8 12 16 20 24 28 222 * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 223 * 224 * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into 225 * the top 17 bits of BR2. 226 */ 227 228 #define CONFIG_SYS_BR2_PRELIM 0xf0001861 /*Port size=32bit, MSEL=SDRAM */ 229 230 /* 231 * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. 232 * 233 * For OR2, need: 234 * 64MB mask for AM, OR2[0:7] = 1111 1100 235 * XAM, OR2[17:18] = 11 236 * 9 columns OR2[19-21] = 010 237 * 13 rows OR2[23-25] = 100 238 * EAD set for extra time OR[31] = 1 239 * 240 * 0 4 8 12 16 20 24 28 241 * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 242 */ 243 244 #define CONFIG_SYS_OR2_PRELIM 0xfc006901 245 246 #define CONFIG_SYS_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */ 247 #define CONFIG_SYS_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32 */ 248 249 #define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723 250 251 #endif 252 253 /* 254 * Windows to access PIB via local bus 255 */ 256 #define CONFIG_SYS_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */ 257 #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */ 258 259 /* 260 * CS2 on Local Bus, to PIB 261 */ 262 #define CONFIG_SYS_BR2_PRELIM 0xf8008801 /* CS2 base address at 0xf8008000 */ 263 #define CONFIG_SYS_OR2_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ 264 265 /* 266 * CS3 on Local Bus, to PIB 267 */ 268 #define CONFIG_SYS_BR3_PRELIM 0xf8010801 /* CS3 base address at 0xf8010000 */ 269 #define CONFIG_SYS_OR3_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */ 270 271 /* 272 * Serial Port 273 */ 274 #define CONFIG_CONS_INDEX 1 275 #define CONFIG_SYS_NS16550 276 #define CONFIG_SYS_NS16550_SERIAL 277 #define CONFIG_SYS_NS16550_REG_SIZE 1 278 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 279 280 #define CONFIG_SYS_BAUDRATE_TABLE \ 281 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 282 283 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 284 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 285 286 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 287 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 288 /* Use the HUSH parser */ 289 #define CONFIG_SYS_HUSH_PARSER 290 #ifdef CONFIG_SYS_HUSH_PARSER 291 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 292 #endif 293 294 /* pass open firmware flat tree */ 295 #define CONFIG_OF_LIBFDT 1 296 #define CONFIG_OF_BOARD_SETUP 1 297 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 298 299 /* I2C */ 300 #define CONFIG_HARD_I2C /* I2C with hardware support */ 301 #undef CONFIG_SOFT_I2C /* I2C bit-banged */ 302 #define CONFIG_FSL_I2C 303 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 304 #define CONFIG_SYS_I2C_SLAVE 0x7F 305 #define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 306 #define CONFIG_SYS_I2C_OFFSET 0x3000 307 308 /* 309 * Config on-board RTC 310 */ 311 #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ 312 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 313 314 /* 315 * General PCI 316 * Addresses are mapped 1-1. 317 */ 318 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 319 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 320 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 321 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 322 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 323 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 324 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 325 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 326 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ 327 328 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 329 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 330 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 331 332 333 #ifdef CONFIG_PCI 334 335 #define CONFIG_NET_MULTI 336 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 337 #define CONFIG_83XX_PCI_STREAMING 338 339 #undef CONFIG_EEPRO100 340 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 341 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 342 343 #endif /* CONFIG_PCI */ 344 345 346 #ifndef CONFIG_NET_MULTI 347 #define CONFIG_NET_MULTI 1 348 #endif 349 350 /* 351 * QE UEC ethernet configuration 352 */ 353 #define CONFIG_UEC_ETH 354 #define CONFIG_ETHPRIME "UEC0" 355 356 #define CONFIG_UEC_ETH1 /* ETH3 */ 357 358 #ifdef CONFIG_UEC_ETH1 359 #define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ 360 #define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 361 #define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 362 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH 363 #define CONFIG_SYS_UEC1_PHY_ADDR 3 364 #define CONFIG_SYS_UEC1_INTERFACE_TYPE MII 365 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 366 #endif 367 368 #define CONFIG_UEC_ETH2 /* ETH4 */ 369 370 #ifdef CONFIG_UEC_ETH2 371 #define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ 372 #define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 373 #define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 374 #define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH 375 #define CONFIG_SYS_UEC2_PHY_ADDR 4 376 #define CONFIG_SYS_UEC2_INTERFACE_TYPE MII 377 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 378 #endif 379 380 /* 381 * Environment 382 */ 383 #ifndef CONFIG_SYS_RAMBOOT 384 #define CONFIG_ENV_IS_IN_FLASH 1 385 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 386 #define CONFIG_ENV_SECT_SIZE 0x20000 387 #define CONFIG_ENV_SIZE 0x2000 388 #else 389 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 390 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 391 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 392 #define CONFIG_ENV_SIZE 0x2000 393 #endif 394 395 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 396 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 397 398 /* 399 * BOOTP options 400 */ 401 #define CONFIG_BOOTP_BOOTFILESIZE 402 #define CONFIG_BOOTP_BOOTPATH 403 #define CONFIG_BOOTP_GATEWAY 404 #define CONFIG_BOOTP_HOSTNAME 405 406 407 /* 408 * Command line configuration. 409 */ 410 #include <config_cmd_default.h> 411 412 #define CONFIG_CMD_PING 413 #define CONFIG_CMD_I2C 414 #define CONFIG_CMD_ASKENV 415 416 #if defined(CONFIG_PCI) 417 #define CONFIG_CMD_PCI 418 #endif 419 420 #if defined(CONFIG_SYS_RAMBOOT) 421 #undef CONFIG_CMD_SAVEENV 422 #undef CONFIG_CMD_LOADS 423 #endif 424 425 426 #undef CONFIG_WATCHDOG /* watchdog disabled */ 427 428 /* 429 * Miscellaneous configurable options 430 */ 431 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 432 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 433 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 434 435 #if defined(CONFIG_CMD_KGDB) 436 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 437 #else 438 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 439 #endif 440 441 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 442 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 443 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 444 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 445 446 /* 447 * For booting Linux, the board info and command line data 448 * have to be in the first 256 MB of memory, since this is 449 * the maximum mapped by the Linux kernel during initialization. 450 */ 451 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 452 453 /* 454 * Core HID Setup 455 */ 456 #define CONFIG_SYS_HID0_INIT 0x000000000 457 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 458 HID0_ENABLE_INSTRUCTION_CACHE) 459 #define CONFIG_SYS_HID2 HID2_HBE 460 461 /* 462 * MMU Setup 463 */ 464 465 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 466 467 /* DDR: cache cacheable */ 468 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 469 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) 470 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 471 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 472 473 /* IMMRBAR & PCI IO: cache-inhibit and guarded */ 474 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ 475 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 476 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) 477 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 478 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 479 480 /* BCSR: cache-inhibit and guarded */ 481 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR | BATL_PP_10 | \ 482 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 483 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) 484 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 485 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 486 487 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 488 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 489 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) 490 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ 491 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 492 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 493 494 #define CONFIG_SYS_IBAT4L (0) 495 #define CONFIG_SYS_IBAT4U (0) 496 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 497 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 498 499 /* Stack in dcache: cacheable, no memory coherence */ 500 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) 501 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 502 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 503 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 504 505 #ifdef CONFIG_PCI 506 /* PCI MEM space: cacheable */ 507 #define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) 508 #define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 509 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 510 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 511 /* PCI MMIO space: cache-inhibit and guarded */ 512 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \ 513 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 514 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 515 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 516 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 517 #else 518 #define CONFIG_SYS_IBAT6L (0) 519 #define CONFIG_SYS_IBAT6U (0) 520 #define CONFIG_SYS_IBAT7L (0) 521 #define CONFIG_SYS_IBAT7U (0) 522 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 523 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 524 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 525 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 526 #endif 527 528 #if defined(CONFIG_CMD_KGDB) 529 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 530 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 531 #endif 532 533 /* 534 * Environment Configuration 535 */ #define CONFIG_ENV_OVERWRITE 536 537 #if defined(CONFIG_UEC_ETH) 538 #define CONFIG_HAS_ETH0 539 #define CONFIG_HAS_ETH1 540 #endif 541 542 #define CONFIG_BAUDRATE 115200 543 544 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 545 546 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 547 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 548 549 #define CONFIG_EXTRA_ENV_SETTINGS \ 550 "netdev=eth0\0" \ 551 "consoledev=ttyS0\0" \ 552 "ramdiskaddr=1000000\0" \ 553 "ramdiskfile=ramfs.83xx\0" \ 554 "fdtaddr=780000\0" \ 555 "fdtfile=mpc832x_mds.dtb\0" \ 556 "" 557 558 #define CONFIG_NFSBOOTCOMMAND \ 559 "setenv bootargs root=/dev/nfs rw " \ 560 "nfsroot=$serverip:$rootpath " \ 561 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 562 "console=$consoledev,$baudrate $othbootargs;" \ 563 "tftp $loadaddr $bootfile;" \ 564 "tftp $fdtaddr $fdtfile;" \ 565 "bootm $loadaddr - $fdtaddr" 566 567 #define CONFIG_RAMBOOTCOMMAND \ 568 "setenv bootargs root=/dev/ram rw " \ 569 "console=$consoledev,$baudrate $othbootargs;" \ 570 "tftp $ramdiskaddr $ramdiskfile;" \ 571 "tftp $loadaddr $bootfile;" \ 572 "tftp $fdtaddr $fdtfile;" \ 573 "bootm $loadaddr $ramdiskaddr $fdtaddr" 574 575 576 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 577 578 #endif /* __CONFIG_H */ 579