1 /*
2  * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
3  *
4  * Dave Liu <daveliu@freescale.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #ifndef __CONFIG_H
10 #define __CONFIG_H
11 
12 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
13 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
14 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
15 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
16 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
17 
18 #ifdef CONFIG_NAND_U_BOOT
19 #define CONFIG_SYS_TEXT_BASE	0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */
20 #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
21 #ifdef CONFIG_NAND_SPL
22 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
23 #endif /* CONFIG_NAND_SPL */
24 #endif /* CONFIG_NAND_U_BOOT */
25 
26 #ifndef CONFIG_SYS_TEXT_BASE
27 #define CONFIG_SYS_TEXT_BASE	0xFE000000
28 #endif
29 
30 #ifndef CONFIG_SYS_MONITOR_BASE
31 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
32 #endif
33 
34 /*
35  * High Level Configuration Options
36  */
37 #define CONFIG_E300		1 /* E300 family */
38 #define CONFIG_MPC83xx		1 /* MPC83xx family */
39 #define CONFIG_MPC831x		1 /* MPC831x CPU family */
40 #define CONFIG_MPC8315		1 /* MPC8315 CPU specific */
41 #define CONFIG_MPC8315ERDB	1 /* MPC8315ERDB board specific */
42 
43 /*
44  * System Clock Setup
45  */
46 #define CONFIG_83XX_CLKIN	66666667 /* in Hz */
47 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
48 
49 /*
50  * Hardware Reset Configuration Word
51  * if CLKIN is 66.66MHz, then
52  * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
53  */
54 #define CONFIG_SYS_HRCW_LOW (\
55 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
56 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
57 	HRCWL_SVCOD_DIV_2 |\
58 	HRCWL_CSB_TO_CLKIN_2X1 |\
59 	HRCWL_CORE_TO_CSB_3X1)
60 #define CONFIG_SYS_HRCW_HIGH_BASE (\
61 	HRCWH_PCI_HOST |\
62 	HRCWH_PCI1_ARBITER_ENABLE |\
63 	HRCWH_CORE_ENABLE |\
64 	HRCWH_BOOTSEQ_DISABLE |\
65 	HRCWH_SW_WATCHDOG_DISABLE |\
66 	HRCWH_TSEC1M_IN_RGMII |\
67 	HRCWH_TSEC2M_IN_RGMII |\
68 	HRCWH_BIG_ENDIAN |\
69 	HRCWH_LALE_NORMAL)
70 
71 #ifdef CONFIG_NAND_SPL
72 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
73 		       HRCWH_FROM_0XFFF00100 |\
74 		       HRCWH_ROM_LOC_NAND_SP_8BIT |\
75 		       HRCWH_RL_EXT_NAND)
76 #else
77 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
78 		       HRCWH_FROM_0X00000100 |\
79 		       HRCWH_ROM_LOC_LOCAL_16BIT |\
80 		       HRCWH_RL_EXT_LEGACY)
81 #endif
82 
83 /*
84  * System IO Config
85  */
86 #define CONFIG_SYS_SICRH		0x00000000
87 #define CONFIG_SYS_SICRL		0x00000000 /* 3.3V, no delay */
88 
89 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
90 #define CONFIG_HWCONFIG
91 
92 /*
93  * IMMR new address
94  */
95 #define CONFIG_SYS_IMMR		0xE0000000
96 
97 #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
98 #define CONFIG_DEFAULT_IMMR	CONFIG_SYS_IMMR
99 #endif
100 
101 /*
102  * Arbiter Setup
103  */
104 #define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
105 #define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
106 #define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
107 
108 /*
109  * DDR Setup
110  */
111 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
112 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
113 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
114 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
115 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
116 				| DDRCDR_PZ_LOZ \
117 				| DDRCDR_NZ_LOZ \
118 				| DDRCDR_ODT \
119 				| DDRCDR_Q_DRN)
120 				/* 0x7b880001 */
121 /*
122  * Manually set up DDR parameters
123  * consist of two chips HY5PS12621BFP-C4 from HYNIX
124  */
125 #define CONFIG_SYS_DDR_SIZE		128 /* MB */
126 #define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
127 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
128 				| CSCONFIG_ODT_RD_NEVER \
129 				| CSCONFIG_ODT_WR_ONLY_CURRENT \
130 				| CSCONFIG_ROW_BIT_13 \
131 				| CSCONFIG_COL_BIT_10)
132 				/* 0x80010102 */
133 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
134 #define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
135 				| (0 << TIMING_CFG0_WRT_SHIFT) \
136 				| (0 << TIMING_CFG0_RRT_SHIFT) \
137 				| (0 << TIMING_CFG0_WWT_SHIFT) \
138 				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
139 				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
140 				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
141 				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
142 				/* 0x00220802 */
143 #define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
144 				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
145 				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
146 				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
147 				| (6 << TIMING_CFG1_REFREC_SHIFT) \
148 				| (2 << TIMING_CFG1_WRREC_SHIFT) \
149 				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
150 				| (2 << TIMING_CFG1_WRTORD_SHIFT))
151 				/* 0x27256222 */
152 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
153 				| (4 << TIMING_CFG2_CPO_SHIFT) \
154 				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
155 				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
156 				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
157 				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
158 				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
159 				/* 0x121048c5 */
160 #define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
161 				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
162 				/* 0x03600100 */
163 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
164 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
165 				| SDRAM_CFG_DBW_32)
166 				/* 0x43080000 */
167 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
168 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
169 				| (0x0232 << SDRAM_MODE_SD_SHIFT))
170 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
171 #define CONFIG_SYS_DDR_MODE2	0x00000000
172 
173 /*
174  * Memory test
175  */
176 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
177 #define CONFIG_SYS_MEMTEST_START	0x00040000 /* memtest region */
178 #define CONFIG_SYS_MEMTEST_END		0x00140000
179 
180 /*
181  * The reserved memory
182  */
183 #define CONFIG_SYS_MONITOR_LEN	(384 * 1024) /* Reserve 384 kB for Mon */
184 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
185 
186 /*
187  * Initial RAM Base Address Setup
188  */
189 #define CONFIG_SYS_INIT_RAM_LOCK	1
190 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
191 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
192 #define CONFIG_SYS_GBL_DATA_OFFSET	\
193 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
194 
195 /*
196  * Local Bus Configuration & Clock Setup
197  */
198 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
199 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
200 #define CONFIG_SYS_LBC_LBCR		0x00040000
201 #define CONFIG_FSL_ELBC		1
202 
203 /*
204  * FLASH on the Local Bus
205  */
206 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
207 #define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
208 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
209 
210 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
211 #define CONFIG_SYS_FLASH_SIZE		8	/* FLASH size is 8M */
212 #define CONFIG_SYS_FLASH_PROTECTION	1	/* Use h/w Flash protection. */
213 
214 					/* Window base at flash base */
215 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
216 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
217 
218 #define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
219 					| BR_PS_16	/* 16 bit port */ \
220 					| BR_MS_GPCM	/* MSEL = GPCM */ \
221 					| BR_V)		/* valid */
222 #define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
223 					| OR_UPM_XAM \
224 					| OR_GPCM_CSNT \
225 					| OR_GPCM_ACS_DIV2 \
226 					| OR_GPCM_XACS \
227 					| OR_GPCM_SCY_15 \
228 					| OR_GPCM_TRLX_SET \
229 					| OR_GPCM_EHTR_SET \
230 					| OR_GPCM_EAD)
231 
232 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
233 /* 127 64KB sectors and 8 8KB top sectors per device */
234 #define CONFIG_SYS_MAX_FLASH_SECT	135
235 
236 #undef CONFIG_SYS_FLASH_CHECKSUM
237 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
238 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
239 
240 /*
241  * NAND Flash on the Local Bus
242  */
243 
244 #ifdef CONFIG_NAND_SPL
245 #define CONFIG_SYS_NAND_BASE		0xFFF00000
246 #else
247 #define CONFIG_SYS_NAND_BASE		0xE0600000
248 #endif
249 
250 #define CONFIG_MTD_DEVICE
251 #define CONFIG_MTD_PARTITION
252 #define CONFIG_CMD_MTDPARTS
253 #define MTDIDS_DEFAULT			"nand0=e0600000.flash"
254 #define MTDPARTS_DEFAULT		\
255 	"mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)"
256 
257 #define CONFIG_SYS_MAX_NAND_DEVICE	1
258 #define CONFIG_MTD_NAND_VERIFY_WRITE	1
259 #define CONFIG_CMD_NAND			1
260 #define CONFIG_NAND_FSL_ELBC		1
261 #define CONFIG_SYS_NAND_BLOCK_SIZE	16384
262 #define CONFIG_SYS_NAND_WINDOW_SIZE    (32 * 1024)     /* 0x00008000 */
263 
264 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
265 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
266 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
267 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
268 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
269 
270 #define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
271 				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
272 				| BR_PS_8		/* 8 bit port */ \
273 				| BR_MS_FCM		/* MSEL = FCM */ \
274 				| BR_V)			/* valid */
275 #define CONFIG_SYS_NAND_OR_PRELIM	\
276 				(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
277 				| OR_FCM_CSCT \
278 				| OR_FCM_CST \
279 				| OR_FCM_CHT \
280 				| OR_FCM_SCY_1 \
281 				| OR_FCM_TRLX \
282 				| OR_FCM_EHTR)
283 				/* 0xFFFF8396 */
284 
285 #ifdef CONFIG_NAND_U_BOOT
286 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM
287 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM
288 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM
289 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM
290 #else
291 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
292 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
293 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
294 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
295 #endif
296 
297 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
298 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
299 
300 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
301 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
302 
303 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
304 	!defined(CONFIG_NAND_SPL)
305 #define CONFIG_SYS_RAMBOOT
306 #else
307 #undef CONFIG_SYS_RAMBOOT
308 #endif
309 
310 /*
311  * Serial Port
312  */
313 #define CONFIG_CONS_INDEX	1
314 #define CONFIG_SYS_NS16550
315 #define CONFIG_SYS_NS16550_SERIAL
316 #define CONFIG_SYS_NS16550_REG_SIZE	1
317 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
318 
319 #define CONFIG_SYS_BAUDRATE_TABLE  \
320 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
321 
322 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
323 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
324 
325 /* Use the HUSH parser */
326 #define CONFIG_SYS_HUSH_PARSER
327 
328 /* Pass open firmware flat tree */
329 #define CONFIG_OF_LIBFDT	1
330 #define CONFIG_OF_BOARD_SETUP	1
331 #define CONFIG_OF_STDOUT_VIA_ALIAS	1
332 
333 /* I2C */
334 #define CONFIG_SYS_I2C
335 #define CONFIG_SYS_I2C_FSL
336 #define CONFIG_SYS_FSL_I2C_SPEED	400000
337 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
338 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
339 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }
340 
341 /*
342  * Board info - revision and where boot from
343  */
344 #define CONFIG_SYS_I2C_PCF8574A_ADDR	0x39
345 
346 /*
347  * Config on-board RTC
348  */
349 #define CONFIG_RTC_DS1337	/* ds1339 on board, use ds1337 rtc via i2c */
350 #define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
351 
352 /*
353  * General PCI
354  * Addresses are mapped 1-1.
355  */
356 #define CONFIG_SYS_PCI_MEM_BASE		0x80000000
357 #define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
358 #define CONFIG_SYS_PCI_MEM_SIZE		0x10000000 /* 256M */
359 #define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
360 #define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
361 #define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
362 #define CONFIG_SYS_PCI_IO_BASE		0x00000000
363 #define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
364 #define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */
365 
366 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
367 #define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
368 #define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
369 
370 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
371 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
372 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
373 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
374 #define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
375 #define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
376 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
377 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
378 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
379 
380 #define CONFIG_SYS_PCIE2_BASE		0xC0000000
381 #define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
382 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
383 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
384 #define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
385 #define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
386 #define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
387 #define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
388 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
389 
390 #define CONFIG_PCI
391 #define CONFIG_PCI_INDIRECT_BRIDGE
392 #define CONFIG_PCIE
393 
394 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
395 
396 #define CONFIG_EEPRO100
397 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
398 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
399 
400 #define CONFIG_HAS_FSL_DR_USB
401 #define CONFIG_SYS_SCCR_USBDRCM		3
402 
403 #define CONFIG_CMD_USB
404 #define CONFIG_USB_STORAGE
405 #define CONFIG_USB_EHCI
406 #define CONFIG_USB_EHCI_FSL
407 #define CONFIG_USB_PHY_TYPE	"utmi"
408 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
409 
410 /*
411  * TSEC
412  */
413 #define CONFIG_TSEC_ENET	/* TSEC ethernet support */
414 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
415 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
416 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
417 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
418 
419 /*
420  * TSEC ethernet configuration
421  */
422 #define CONFIG_MII		1 /* MII PHY management */
423 #define CONFIG_TSEC1		1
424 #define CONFIG_TSEC1_NAME	"eTSEC0"
425 #define CONFIG_TSEC2		1
426 #define CONFIG_TSEC2_NAME	"eTSEC1"
427 #define TSEC1_PHY_ADDR		0
428 #define TSEC2_PHY_ADDR		1
429 #define TSEC1_PHYIDX		0
430 #define TSEC2_PHYIDX		0
431 #define TSEC1_FLAGS		TSEC_GIGABIT
432 #define TSEC2_FLAGS		TSEC_GIGABIT
433 
434 /* Options are: eTSEC[0-1] */
435 #define CONFIG_ETHPRIME		"eTSEC1"
436 
437 /*
438  * SATA
439  */
440 #define CONFIG_LIBATA
441 #define CONFIG_FSL_SATA
442 
443 #define CONFIG_SYS_SATA_MAX_DEVICE	2
444 #define CONFIG_SATA1
445 #define CONFIG_SYS_SATA1_OFFSET	0x18000
446 #define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
447 #define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
448 #define CONFIG_SATA2
449 #define CONFIG_SYS_SATA2_OFFSET	0x19000
450 #define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
451 #define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA
452 
453 #ifdef CONFIG_FSL_SATA
454 #define CONFIG_LBA48
455 #define CONFIG_CMD_SATA
456 #define CONFIG_DOS_PARTITION
457 #define CONFIG_CMD_EXT2
458 #endif
459 
460 /*
461  * Environment
462  */
463 #if defined(CONFIG_NAND_U_BOOT)
464 	#define CONFIG_ENV_IS_IN_NAND	1
465 	#define CONFIG_ENV_OFFSET		(512 * 1024)
466 	#define CONFIG_ENV_SECT_SIZE	CONFIG_SYS_NAND_BLOCK_SIZE
467 	#define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
468 	#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
469 	#define CONFIG_ENV_RANGE	(CONFIG_ENV_SECT_SIZE * 4)
470 	#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
471 						 CONFIG_ENV_RANGE)
472 #elif !defined(CONFIG_SYS_RAMBOOT)
473 	#define CONFIG_ENV_IS_IN_FLASH	1
474 	#define CONFIG_ENV_ADDR		\
475 			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
476 	#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
477 	#define CONFIG_ENV_SIZE		0x2000
478 #else
479 	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
480 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
481 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
482 	#define CONFIG_ENV_SIZE		0x2000
483 #endif
484 
485 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
486 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
487 
488 /*
489  * BOOTP options
490  */
491 #define CONFIG_BOOTP_BOOTFILESIZE
492 #define CONFIG_BOOTP_BOOTPATH
493 #define CONFIG_BOOTP_GATEWAY
494 #define CONFIG_BOOTP_HOSTNAME
495 
496 /*
497  * Command line configuration.
498  */
499 #include <config_cmd_default.h>
500 
501 #define CONFIG_CMD_PING
502 #define CONFIG_CMD_I2C
503 #define CONFIG_CMD_MII
504 #define CONFIG_CMD_DATE
505 #define CONFIG_CMD_PCI
506 
507 #if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT)
508     #undef CONFIG_CMD_SAVEENV
509     #undef CONFIG_CMD_LOADS
510 #endif
511 
512 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
513 #define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
514 
515 #undef CONFIG_WATCHDOG		/* watchdog disabled */
516 
517 /*
518  * Miscellaneous configurable options
519  */
520 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
521 #define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
522 
523 #if defined(CONFIG_CMD_KGDB)
524 	#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
525 #else
526 	#define CONFIG_SYS_CBSIZE	256 /* Console I/O Buffer Size */
527 #endif
528 
529 				/* Print Buffer Size */
530 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
531 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
532 				/* Boot Argument Buffer Size */
533 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
534 
535 /*
536  * For booting Linux, the board info and command line data
537  * have to be in the first 256 MB of memory, since this is
538  * the maximum mapped by the Linux kernel during initialization.
539  */
540 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
541 
542 /*
543  * Core HID Setup
544  */
545 #define CONFIG_SYS_HID0_INIT	0x000000000
546 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
547 				 HID0_ENABLE_INSTRUCTION_CACHE | \
548 				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
549 #define CONFIG_SYS_HID2		HID2_HBE
550 
551 /*
552  * MMU Setup
553  */
554 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
555 
556 /* DDR: cache cacheable */
557 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
558 				| BATL_PP_RW \
559 				| BATL_MEMCOHERENCE)
560 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
561 				| BATU_BL_128M \
562 				| BATU_VS \
563 				| BATU_VP)
564 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
565 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
566 
567 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
568 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
569 				| BATL_PP_RW \
570 				| BATL_CACHEINHIBIT \
571 				| BATL_GUARDEDSTORAGE)
572 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
573 				| BATU_BL_8M \
574 				| BATU_VS \
575 				| BATU_VP)
576 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
577 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
578 
579 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
580 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE \
581 				| BATL_PP_RW \
582 				| BATL_MEMCOHERENCE)
583 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE \
584 				| BATU_BL_32M \
585 				| BATU_VS \
586 				| BATU_VP)
587 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE \
588 				| BATL_PP_RW \
589 				| BATL_CACHEINHIBIT \
590 				| BATL_GUARDEDSTORAGE)
591 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
592 
593 /* Stack in dcache: cacheable, no memory coherence */
594 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
595 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR \
596 				| BATU_BL_128K \
597 				| BATU_VS \
598 				| BATU_VP)
599 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
600 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
601 
602 /* PCI MEM space: cacheable */
603 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI_MEM_PHYS \
604 				| BATL_PP_RW \
605 				| BATL_MEMCOHERENCE)
606 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI_MEM_PHYS \
607 				| BATU_BL_256M \
608 				| BATU_VS \
609 				| BATU_VP)
610 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
611 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
612 
613 /* PCI MMIO space: cache-inhibit and guarded */
614 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI_MMIO_PHYS \
615 				| BATL_PP_RW \
616 				| BATL_CACHEINHIBIT \
617 				| BATL_GUARDEDSTORAGE)
618 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI_MMIO_PHYS \
619 				| BATU_BL_256M \
620 				| BATU_VS \
621 				| BATU_VP)
622 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
623 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
624 
625 #define CONFIG_SYS_IBAT6L	0
626 #define CONFIG_SYS_IBAT6U	0
627 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
628 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
629 
630 #define CONFIG_SYS_IBAT7L	0
631 #define CONFIG_SYS_IBAT7U	0
632 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
633 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
634 
635 #if defined(CONFIG_CMD_KGDB)
636 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
637 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
638 #endif
639 
640 /*
641  * Environment Configuration
642  */
643 
644 #define CONFIG_ENV_OVERWRITE
645 
646 #if defined(CONFIG_TSEC_ENET)
647 #define CONFIG_HAS_ETH0
648 #define CONFIG_HAS_ETH1
649 #endif
650 
651 #define CONFIG_BAUDRATE 115200
652 
653 #define CONFIG_LOADADDR 800000	/* default location for tftp and bootm */
654 
655 #define CONFIG_BOOTDELAY 6	/* -1 disables auto-boot */
656 #undef CONFIG_BOOTARGS		/* the boot command will set bootargs */
657 
658 #define CONFIG_EXTRA_ENV_SETTINGS					\
659 	"netdev=eth0\0"							\
660 	"consoledev=ttyS0\0"						\
661 	"ramdiskaddr=1000000\0"						\
662 	"ramdiskfile=ramfs.83xx\0"					\
663 	"fdtaddr=780000\0"						\
664 	"fdtfile=mpc8315erdb.dtb\0"					\
665 	"usb_phy_type=utmi\0"						\
666 	""
667 
668 #define CONFIG_NFSBOOTCOMMAND						\
669 	"setenv bootargs root=/dev/nfs rw "				\
670 		"nfsroot=$serverip:$rootpath "				\
671 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
672 							"$netdev:off "	\
673 		"console=$consoledev,$baudrate $othbootargs;"		\
674 	"tftp $loadaddr $bootfile;"					\
675 	"tftp $fdtaddr $fdtfile;"					\
676 	"bootm $loadaddr - $fdtaddr"
677 
678 #define CONFIG_RAMBOOTCOMMAND						\
679 	"setenv bootargs root=/dev/ram rw "				\
680 		"console=$consoledev,$baudrate $othbootargs;"		\
681 	"tftp $ramdiskaddr $ramdiskfile;"				\
682 	"tftp $loadaddr $bootfile;"					\
683 	"tftp $fdtaddr $fdtfile;"					\
684 	"bootm $loadaddr $ramdiskaddr $fdtaddr"
685 
686 
687 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
688 
689 #endif	/* __CONFIG_H */
690