1 /* 2 * Copyright (C) 2007-2010 Freescale Semiconductor, Inc. 3 * 4 * Dave Liu <daveliu@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #define CONFIG_DISPLAY_BOARDINFO 13 14 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) 15 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 16 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 17 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 18 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 19 20 #ifndef CONFIG_SYS_TEXT_BASE 21 #define CONFIG_SYS_TEXT_BASE 0xFE000000 22 #endif 23 24 #ifndef CONFIG_SYS_MONITOR_BASE 25 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 26 #endif 27 28 /* 29 * High Level Configuration Options 30 */ 31 #define CONFIG_E300 1 /* E300 family */ 32 #define CONFIG_MPC831x 1 /* MPC831x CPU family */ 33 #define CONFIG_MPC8315 1 /* MPC8315 CPU specific */ 34 #define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */ 35 36 /* 37 * System Clock Setup 38 */ 39 #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ 40 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 41 42 /* 43 * Hardware Reset Configuration Word 44 * if CLKIN is 66.66MHz, then 45 * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz 46 */ 47 #define CONFIG_SYS_HRCW_LOW (\ 48 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 49 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 50 HRCWL_SVCOD_DIV_2 |\ 51 HRCWL_CSB_TO_CLKIN_2X1 |\ 52 HRCWL_CORE_TO_CSB_3X1) 53 #define CONFIG_SYS_HRCW_HIGH_BASE (\ 54 HRCWH_PCI_HOST |\ 55 HRCWH_PCI1_ARBITER_ENABLE |\ 56 HRCWH_CORE_ENABLE |\ 57 HRCWH_BOOTSEQ_DISABLE |\ 58 HRCWH_SW_WATCHDOG_DISABLE |\ 59 HRCWH_TSEC1M_IN_RGMII |\ 60 HRCWH_TSEC2M_IN_RGMII |\ 61 HRCWH_BIG_ENDIAN |\ 62 HRCWH_LALE_NORMAL) 63 64 #ifdef CONFIG_NAND_SPL 65 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 66 HRCWH_FROM_0XFFF00100 |\ 67 HRCWH_ROM_LOC_NAND_SP_8BIT |\ 68 HRCWH_RL_EXT_NAND) 69 #else 70 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 71 HRCWH_FROM_0X00000100 |\ 72 HRCWH_ROM_LOC_LOCAL_16BIT |\ 73 HRCWH_RL_EXT_LEGACY) 74 #endif 75 76 /* 77 * System IO Config 78 */ 79 #define CONFIG_SYS_SICRH 0x00000000 80 #define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */ 81 82 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 83 #define CONFIG_HWCONFIG 84 85 /* 86 * IMMR new address 87 */ 88 #define CONFIG_SYS_IMMR 0xE0000000 89 90 /* 91 * Arbiter Setup 92 */ 93 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 94 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 95 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 96 97 /* 98 * DDR Setup 99 */ 100 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 101 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 102 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 103 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 104 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 105 | DDRCDR_PZ_LOZ \ 106 | DDRCDR_NZ_LOZ \ 107 | DDRCDR_ODT \ 108 | DDRCDR_Q_DRN) 109 /* 0x7b880001 */ 110 /* 111 * Manually set up DDR parameters 112 * consist of two chips HY5PS12621BFP-C4 from HYNIX 113 */ 114 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 115 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 116 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 117 | CSCONFIG_ODT_RD_NEVER \ 118 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 119 | CSCONFIG_ROW_BIT_13 \ 120 | CSCONFIG_COL_BIT_10) 121 /* 0x80010102 */ 122 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 123 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 124 | (0 << TIMING_CFG0_WRT_SHIFT) \ 125 | (0 << TIMING_CFG0_RRT_SHIFT) \ 126 | (0 << TIMING_CFG0_WWT_SHIFT) \ 127 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 128 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 129 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 130 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 131 /* 0x00220802 */ 132 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 133 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 134 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 135 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 136 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 137 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 138 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 139 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 140 /* 0x27256222 */ 141 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 142 | (4 << TIMING_CFG2_CPO_SHIFT) \ 143 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 144 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 145 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 146 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 147 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 148 /* 0x121048c5 */ 149 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 150 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 151 /* 0x03600100 */ 152 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 153 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 154 | SDRAM_CFG_DBW_32) 155 /* 0x43080000 */ 156 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 157 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 158 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 159 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 160 #define CONFIG_SYS_DDR_MODE2 0x00000000 161 162 /* 163 * Memory test 164 */ 165 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 166 #define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ 167 #define CONFIG_SYS_MEMTEST_END 0x00140000 168 169 /* 170 * The reserved memory 171 */ 172 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 173 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 174 175 /* 176 * Initial RAM Base Address Setup 177 */ 178 #define CONFIG_SYS_INIT_RAM_LOCK 1 179 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 180 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 181 #define CONFIG_SYS_GBL_DATA_OFFSET \ 182 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 183 184 /* 185 * Local Bus Configuration & Clock Setup 186 */ 187 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 188 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 189 #define CONFIG_SYS_LBC_LBCR 0x00040000 190 #define CONFIG_FSL_ELBC 1 191 192 /* 193 * FLASH on the Local Bus 194 */ 195 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 196 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 197 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 198 199 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 200 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ 201 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 202 203 /* Window base at flash base */ 204 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 205 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 206 207 #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ 208 | BR_PS_16 /* 16 bit port */ \ 209 | BR_MS_GPCM /* MSEL = GPCM */ \ 210 | BR_V) /* valid */ 211 #define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 212 | OR_UPM_XAM \ 213 | OR_GPCM_CSNT \ 214 | OR_GPCM_ACS_DIV2 \ 215 | OR_GPCM_XACS \ 216 | OR_GPCM_SCY_15 \ 217 | OR_GPCM_TRLX_SET \ 218 | OR_GPCM_EHTR_SET \ 219 | OR_GPCM_EAD) 220 221 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 222 /* 127 64KB sectors and 8 8KB top sectors per device */ 223 #define CONFIG_SYS_MAX_FLASH_SECT 135 224 225 #undef CONFIG_SYS_FLASH_CHECKSUM 226 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 227 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 228 229 /* 230 * NAND Flash on the Local Bus 231 */ 232 233 #ifdef CONFIG_NAND_SPL 234 #define CONFIG_SYS_NAND_BASE 0xFFF00000 235 #else 236 #define CONFIG_SYS_NAND_BASE 0xE0600000 237 #endif 238 239 #define CONFIG_MTD_DEVICE 240 #define CONFIG_MTD_PARTITION 241 #define CONFIG_CMD_MTDPARTS 242 #define MTDIDS_DEFAULT "nand0=e0600000.flash" 243 #define MTDPARTS_DEFAULT \ 244 "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" 245 246 #define CONFIG_SYS_MAX_NAND_DEVICE 1 247 #define CONFIG_CMD_NAND 1 248 #define CONFIG_NAND_FSL_ELBC 1 249 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 250 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */ 251 252 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) 253 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 254 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 255 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 256 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 257 258 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ 259 | BR_DECC_CHK_GEN /* Use HW ECC */ \ 260 | BR_PS_8 /* 8 bit port */ \ 261 | BR_MS_FCM /* MSEL = FCM */ \ 262 | BR_V) /* valid */ 263 #define CONFIG_SYS_NAND_OR_PRELIM \ 264 (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \ 265 | OR_FCM_CSCT \ 266 | OR_FCM_CST \ 267 | OR_FCM_CHT \ 268 | OR_FCM_SCY_1 \ 269 | OR_FCM_TRLX \ 270 | OR_FCM_EHTR) 271 /* 0xFFFF8396 */ 272 273 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM 274 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM 275 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 276 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM 277 278 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 279 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 280 281 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 282 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 283 284 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \ 285 !defined(CONFIG_NAND_SPL) 286 #define CONFIG_SYS_RAMBOOT 287 #else 288 #undef CONFIG_SYS_RAMBOOT 289 #endif 290 291 /* 292 * Serial Port 293 */ 294 #define CONFIG_CONS_INDEX 1 295 #define CONFIG_SYS_NS16550 296 #define CONFIG_SYS_NS16550_SERIAL 297 #define CONFIG_SYS_NS16550_REG_SIZE 1 298 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) 299 300 #define CONFIG_SYS_BAUDRATE_TABLE \ 301 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 302 303 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 304 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 305 306 /* Use the HUSH parser */ 307 #define CONFIG_SYS_HUSH_PARSER 308 309 /* Pass open firmware flat tree */ 310 #define CONFIG_OF_LIBFDT 1 311 #define CONFIG_OF_BOARD_SETUP 1 312 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 313 314 /* I2C */ 315 #define CONFIG_SYS_I2C 316 #define CONFIG_SYS_I2C_FSL 317 #define CONFIG_SYS_FSL_I2C_SPEED 400000 318 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 319 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 320 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } 321 322 /* 323 * Board info - revision and where boot from 324 */ 325 #define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 326 327 /* 328 * Config on-board RTC 329 */ 330 #define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ 331 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 332 333 /* 334 * General PCI 335 * Addresses are mapped 1-1. 336 */ 337 #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 338 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE 339 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ 340 #define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 341 #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE 342 #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ 343 #define CONFIG_SYS_PCI_IO_BASE 0x00000000 344 #define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 345 #define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ 346 347 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 348 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 349 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 350 351 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 352 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 353 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 354 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 355 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 356 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 357 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 358 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 359 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 360 361 #define CONFIG_SYS_PCIE2_BASE 0xC0000000 362 #define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 363 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 364 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 365 #define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 366 #define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 367 #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 368 #define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 369 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 370 371 #define CONFIG_PCI 372 #define CONFIG_PCI_INDIRECT_BRIDGE 373 #define CONFIG_PCIE 374 375 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 376 377 #define CONFIG_EEPRO100 378 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 379 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 380 381 #define CONFIG_HAS_FSL_DR_USB 382 #define CONFIG_SYS_SCCR_USBDRCM 3 383 384 #define CONFIG_CMD_USB 385 #define CONFIG_USB_STORAGE 386 #define CONFIG_USB_EHCI 387 #define CONFIG_USB_EHCI_FSL 388 #define CONFIG_USB_PHY_TYPE "utmi" 389 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 390 391 /* 392 * TSEC 393 */ 394 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 395 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 396 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 397 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 398 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 399 400 /* 401 * TSEC ethernet configuration 402 */ 403 #define CONFIG_MII 1 /* MII PHY management */ 404 #define CONFIG_TSEC1 1 405 #define CONFIG_TSEC1_NAME "eTSEC0" 406 #define CONFIG_TSEC2 1 407 #define CONFIG_TSEC2_NAME "eTSEC1" 408 #define TSEC1_PHY_ADDR 0 409 #define TSEC2_PHY_ADDR 1 410 #define TSEC1_PHYIDX 0 411 #define TSEC2_PHYIDX 0 412 #define TSEC1_FLAGS TSEC_GIGABIT 413 #define TSEC2_FLAGS TSEC_GIGABIT 414 415 /* Options are: eTSEC[0-1] */ 416 #define CONFIG_ETHPRIME "eTSEC1" 417 418 /* 419 * SATA 420 */ 421 #define CONFIG_LIBATA 422 #define CONFIG_FSL_SATA 423 424 #define CONFIG_SYS_SATA_MAX_DEVICE 2 425 #define CONFIG_SATA1 426 #define CONFIG_SYS_SATA1_OFFSET 0x18000 427 #define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) 428 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 429 #define CONFIG_SATA2 430 #define CONFIG_SYS_SATA2_OFFSET 0x19000 431 #define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) 432 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 433 434 #ifdef CONFIG_FSL_SATA 435 #define CONFIG_LBA48 436 #define CONFIG_CMD_SATA 437 #define CONFIG_DOS_PARTITION 438 #define CONFIG_CMD_EXT2 439 #endif 440 441 /* 442 * Environment 443 */ 444 #if !defined(CONFIG_SYS_RAMBOOT) 445 #define CONFIG_ENV_IS_IN_FLASH 1 446 #define CONFIG_ENV_ADDR \ 447 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 448 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 449 #define CONFIG_ENV_SIZE 0x2000 450 #else 451 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 452 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 453 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 454 #define CONFIG_ENV_SIZE 0x2000 455 #endif 456 457 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 458 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 459 460 /* 461 * BOOTP options 462 */ 463 #define CONFIG_BOOTP_BOOTFILESIZE 464 #define CONFIG_BOOTP_BOOTPATH 465 #define CONFIG_BOOTP_GATEWAY 466 #define CONFIG_BOOTP_HOSTNAME 467 468 /* 469 * Command line configuration. 470 */ 471 #define CONFIG_CMD_PING 472 #define CONFIG_CMD_I2C 473 #define CONFIG_CMD_MII 474 #define CONFIG_CMD_DATE 475 #define CONFIG_CMD_PCI 476 477 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 478 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 479 480 #undef CONFIG_WATCHDOG /* watchdog disabled */ 481 482 /* 483 * Miscellaneous configurable options 484 */ 485 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 486 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 487 488 #if defined(CONFIG_CMD_KGDB) 489 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 490 #else 491 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 492 #endif 493 494 /* Print Buffer Size */ 495 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 496 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 497 /* Boot Argument Buffer Size */ 498 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 499 500 /* 501 * For booting Linux, the board info and command line data 502 * have to be in the first 256 MB of memory, since this is 503 * the maximum mapped by the Linux kernel during initialization. 504 */ 505 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 506 507 /* 508 * Core HID Setup 509 */ 510 #define CONFIG_SYS_HID0_INIT 0x000000000 511 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 512 HID0_ENABLE_INSTRUCTION_CACHE | \ 513 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 514 #define CONFIG_SYS_HID2 HID2_HBE 515 516 /* 517 * MMU Setup 518 */ 519 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 520 521 /* DDR: cache cacheable */ 522 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 523 | BATL_PP_RW \ 524 | BATL_MEMCOHERENCE) 525 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 526 | BATU_BL_128M \ 527 | BATU_VS \ 528 | BATU_VP) 529 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 530 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 531 532 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 533 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ 534 | BATL_PP_RW \ 535 | BATL_CACHEINHIBIT \ 536 | BATL_GUARDEDSTORAGE) 537 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ 538 | BATU_BL_8M \ 539 | BATU_VS \ 540 | BATU_VP) 541 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 542 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 543 544 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 545 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \ 546 | BATL_PP_RW \ 547 | BATL_MEMCOHERENCE) 548 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \ 549 | BATU_BL_32M \ 550 | BATU_VS \ 551 | BATU_VP) 552 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \ 553 | BATL_PP_RW \ 554 | BATL_CACHEINHIBIT \ 555 | BATL_GUARDEDSTORAGE) 556 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 557 558 /* Stack in dcache: cacheable, no memory coherence */ 559 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 560 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \ 561 | BATU_BL_128K \ 562 | BATU_VS \ 563 | BATU_VP) 564 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 565 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 566 567 /* PCI MEM space: cacheable */ 568 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \ 569 | BATL_PP_RW \ 570 | BATL_MEMCOHERENCE) 571 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \ 572 | BATU_BL_256M \ 573 | BATU_VS \ 574 | BATU_VP) 575 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 576 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 577 578 /* PCI MMIO space: cache-inhibit and guarded */ 579 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \ 580 | BATL_PP_RW \ 581 | BATL_CACHEINHIBIT \ 582 | BATL_GUARDEDSTORAGE) 583 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \ 584 | BATU_BL_256M \ 585 | BATU_VS \ 586 | BATU_VP) 587 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 588 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 589 590 #define CONFIG_SYS_IBAT6L 0 591 #define CONFIG_SYS_IBAT6U 0 592 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 593 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 594 595 #define CONFIG_SYS_IBAT7L 0 596 #define CONFIG_SYS_IBAT7U 0 597 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 598 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 599 600 #if defined(CONFIG_CMD_KGDB) 601 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 602 #endif 603 604 /* 605 * Environment Configuration 606 */ 607 608 #define CONFIG_ENV_OVERWRITE 609 610 #if defined(CONFIG_TSEC_ENET) 611 #define CONFIG_HAS_ETH0 612 #define CONFIG_HAS_ETH1 613 #endif 614 615 #define CONFIG_BAUDRATE 115200 616 617 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 618 619 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 620 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 621 622 #define CONFIG_EXTRA_ENV_SETTINGS \ 623 "netdev=eth0\0" \ 624 "consoledev=ttyS0\0" \ 625 "ramdiskaddr=1000000\0" \ 626 "ramdiskfile=ramfs.83xx\0" \ 627 "fdtaddr=780000\0" \ 628 "fdtfile=mpc8315erdb.dtb\0" \ 629 "usb_phy_type=utmi\0" \ 630 "" 631 632 #define CONFIG_NFSBOOTCOMMAND \ 633 "setenv bootargs root=/dev/nfs rw " \ 634 "nfsroot=$serverip:$rootpath " \ 635 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 636 "$netdev:off " \ 637 "console=$consoledev,$baudrate $othbootargs;" \ 638 "tftp $loadaddr $bootfile;" \ 639 "tftp $fdtaddr $fdtfile;" \ 640 "bootm $loadaddr - $fdtaddr" 641 642 #define CONFIG_RAMBOOTCOMMAND \ 643 "setenv bootargs root=/dev/ram rw " \ 644 "console=$consoledev,$baudrate $othbootargs;" \ 645 "tftp $ramdiskaddr $ramdiskfile;" \ 646 "tftp $loadaddr $bootfile;" \ 647 "tftp $fdtaddr $fdtfile;" \ 648 "bootm $loadaddr $ramdiskaddr $fdtaddr" 649 650 651 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 652 653 #endif /* __CONFIG_H */ 654