1 /* 2 * Copyright (C) 2007 Freescale Semiconductor, Inc. 3 * 4 * Dave Liu <daveliu@freescale.com> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 #ifndef __CONFIG_H 26 #define __CONFIG_H 27 28 /* 29 * High Level Configuration Options 30 */ 31 #define CONFIG_E300 1 /* E300 family */ 32 #define CONFIG_MPC83XX 1 /* MPC83xx family */ 33 #define CONFIG_MPC831X 1 /* MPC831x CPU family */ 34 #define CONFIG_MPC8315 1 /* MPC8315 CPU specific */ 35 #define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */ 36 37 /* 38 * System Clock Setup 39 */ 40 #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ 41 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 42 43 /* 44 * Hardware Reset Configuration Word 45 * if CLKIN is 66.66MHz, then 46 * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz 47 */ 48 #define CFG_HRCW_LOW (\ 49 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 50 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 51 HRCWL_SVCOD_DIV_2 |\ 52 HRCWL_CSB_TO_CLKIN_2X1 |\ 53 HRCWL_CORE_TO_CSB_3X1) 54 #define CFG_HRCW_HIGH (\ 55 HRCWH_PCI_HOST |\ 56 HRCWH_PCI1_ARBITER_ENABLE |\ 57 HRCWH_CORE_ENABLE |\ 58 HRCWH_FROM_0X00000100 |\ 59 HRCWH_BOOTSEQ_DISABLE |\ 60 HRCWH_SW_WATCHDOG_DISABLE |\ 61 HRCWH_ROM_LOC_LOCAL_16BIT |\ 62 HRCWH_RL_EXT_LEGACY |\ 63 HRCWH_TSEC1M_IN_RGMII |\ 64 HRCWH_TSEC2M_IN_RGMII |\ 65 HRCWH_BIG_ENDIAN |\ 66 HRCWH_LALE_NORMAL) 67 68 /* 69 * System IO Config 70 */ 71 #define CFG_SICRH 0x00000000 72 #define CFG_SICRL 0x00000000 /* 3.3V, no delay */ 73 74 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 75 76 /* 77 * IMMR new address 78 */ 79 #define CFG_IMMR 0xE0000000 80 81 /* 82 * Arbiter Setup 83 */ 84 #define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 85 #define CFG_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 86 #define CFG_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 87 88 /* 89 * DDR Setup 90 */ 91 #define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ 92 #define CFG_SDRAM_BASE CFG_DDR_BASE 93 #define CFG_DDR_SDRAM_BASE CFG_DDR_BASE 94 #define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 95 #define CFG_DDRCDR_VALUE ( DDRCDR_EN \ 96 | DDRCDR_PZ_LOZ \ 97 | DDRCDR_NZ_LOZ \ 98 | DDRCDR_ODT \ 99 | DDRCDR_Q_DRN ) 100 /* 0x7b880001 */ 101 /* 102 * Manually set up DDR parameters 103 * consist of two chips HY5PS12621BFP-C4 from HYNIX 104 */ 105 #define CFG_DDR_SIZE 128 /* MB */ 106 #define CFG_DDR_CS0_BNDS 0x00000007 107 #define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ 108 | 0x00010000 /* ODT_WR to CSn */ \ 109 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) 110 /* 0x80010102 */ 111 #define CFG_DDR_TIMING_3 0x00000000 112 #define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ 113 | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ 114 | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ 115 | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ 116 | ( 2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ 117 | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ 118 | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ 119 | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) 120 /* 0x00220802 */ 121 #define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ 122 | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ 123 | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ 124 | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ 125 | ( 6 << TIMING_CFG1_REFREC_SHIFT ) \ 126 | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \ 127 | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ 128 | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) 129 /* 0x39356222 */ 130 #define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ 131 | ( 4 << TIMING_CFG2_CPO_SHIFT ) \ 132 | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ 133 | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ 134 | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ 135 | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ 136 | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) ) 137 /* 0x121048c7 */ 138 #define CFG_DDR_INTERVAL ( ( 0x0360 << SDRAM_INTERVAL_REFINT_SHIFT ) \ 139 | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) 140 /* 0x03600100 */ 141 #define CFG_DDR_SDRAM_CFG ( SDRAM_CFG_SREN \ 142 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 143 | SDRAM_CFG_32_BE ) 144 /* 0x43080000 */ 145 #define CFG_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 146 #define CFG_DDR_MODE ( ( 0x0448 << SDRAM_MODE_ESD_SHIFT ) \ 147 | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) ) 148 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 149 #define CFG_DDR_MODE2 0x00000000 150 151 /* 152 * Memory test 153 */ 154 #undef CFG_DRAM_TEST /* memory test, takes time */ 155 #define CFG_MEMTEST_START 0x00040000 /* memtest region */ 156 #define CFG_MEMTEST_END 0x00140000 157 158 /* 159 * The reserved memory 160 */ 161 #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ 162 163 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) 164 #define CFG_RAMBOOT 165 #else 166 #undef CFG_RAMBOOT 167 #endif 168 169 #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ 170 #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 171 172 /* 173 * Initial RAM Base Address Setup 174 */ 175 #define CFG_INIT_RAM_LOCK 1 176 #define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 177 #define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ 178 #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ 179 #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) 180 181 /* 182 * Local Bus Configuration & Clock Setup 183 */ 184 #define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_2) 185 #define CFG_LBC_LBCR 0x00040000 186 187 /* 188 * FLASH on the Local Bus 189 */ 190 #define CFG_FLASH_CFI /* use the Common Flash Interface */ 191 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 192 #define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT 193 194 #define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ 195 #define CFG_FLASH_SIZE 8 /* FLASH size is 8M */ 196 197 #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ 198 #define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8MB window size */ 199 200 #define CFG_BR0_PRELIM ( CFG_FLASH_BASE /* Flash Base address */ \ 201 | (2 << BR_PS_SHIFT) /* 16 bit port size */ \ 202 | BR_V ) /* valid */ 203 #define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ 204 | OR_UPM_XAM \ 205 | OR_GPCM_CSNT \ 206 | OR_GPCM_ACS_DIV2 \ 207 | OR_GPCM_XACS \ 208 | OR_GPCM_SCY_15 \ 209 | OR_GPCM_TRLX \ 210 | OR_GPCM_EHTR \ 211 | OR_GPCM_EAD ) 212 213 #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ 214 #define CFG_MAX_FLASH_SECT 135 /* 127 64KB sectors and 8 8KB top sectors per device */ 215 216 #undef CFG_FLASH_CHECKSUM 217 #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 218 #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 219 220 /* 221 * NAND Flash on the Local Bus 222 */ 223 #define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ 224 #define CFG_MAX_NAND_DEVICE 1 225 #define NAND_MAX_CHIPS 1 226 #define CONFIG_MTD_NAND_VERIFY_WRITE 227 228 #define CFG_BR1_PRELIM ( CFG_NAND_BASE \ 229 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 230 | BR_PS_8 /* Port Size = 8 bit */ \ 231 | BR_MS_FCM /* MSEL = FCM */ \ 232 | BR_V ) /* valid */ 233 #define CFG_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ 234 | OR_FCM_CSCT \ 235 | OR_FCM_CST \ 236 | OR_FCM_CHT \ 237 | OR_FCM_SCY_1 \ 238 | OR_FCM_TRLX \ 239 | OR_FCM_EHTR ) 240 /* 0xFFFF8396 */ 241 242 #define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE 243 #define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ 244 245 /* 246 * Serial Port 247 */ 248 #define CONFIG_CONS_INDEX 1 249 #undef CONFIG_SERIAL_SOFTWARE_FIFO 250 #define CFG_NS16550 251 #define CFG_NS16550_SERIAL 252 #define CFG_NS16550_REG_SIZE 1 253 #define CFG_NS16550_CLK get_bus_freq(0) 254 255 #define CFG_BAUDRATE_TABLE \ 256 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 257 258 #define CFG_NS16550_COM1 (CFG_IMMR+0x4500) 259 #define CFG_NS16550_COM2 (CFG_IMMR+0x4600) 260 261 /* Use the HUSH parser */ 262 #define CFG_HUSH_PARSER 263 #ifdef CFG_HUSH_PARSER 264 #define CFG_PROMPT_HUSH_PS2 "> " 265 #endif 266 267 /* Pass open firmware flat tree */ 268 #define CONFIG_OF_LIBFDT 1 269 #define CONFIG_OF_BOARD_SETUP 1 270 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 271 272 /* I2C */ 273 #define CONFIG_HARD_I2C /* I2C with hardware support */ 274 #define CONFIG_FSL_I2C 275 #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ 276 #define CFG_I2C_SLAVE 0x7F 277 #define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 278 #define CFG_I2C_OFFSET 0x3000 279 #define CFG_I2C2_OFFSET 0x3100 280 281 /* 282 * Board info - revision and where boot from 283 */ 284 #define CFG_I2C_PCF8574A_ADDR 0x39 285 286 /* 287 * Config on-board RTC 288 */ 289 #define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ 290 #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 291 292 /* 293 * General PCI 294 * Addresses are mapped 1-1. 295 */ 296 #define CFG_PCI_MEM_BASE 0x80000000 297 #define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE 298 #define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ 299 #define CFG_PCI_MMIO_BASE 0x90000000 300 #define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE 301 #define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ 302 #define CFG_PCI_IO_BASE 0x00000000 303 #define CFG_PCI_IO_PHYS 0xE0300000 304 #define CFG_PCI_IO_SIZE 0x100000 /* 1M */ 305 306 #define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE 307 #define CFG_PCI_SLV_MEM_BUS 0x00000000 308 #define CFG_PCI_SLV_MEM_SIZE 0x80000000 309 310 #define CONFIG_PCI 311 #define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ 312 313 #define CONFIG_NET_MULTI 314 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 315 316 #define CONFIG_EEPRO100 317 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 318 #define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 319 320 #ifndef CONFIG_NET_MULTI 321 #define CONFIG_NET_MULTI 1 322 #endif 323 324 #define CONFIG_HAS_FSL_DR_USB 325 326 /* 327 * TSEC 328 */ 329 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 330 #define CFG_TSEC1_OFFSET 0x24000 331 #define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) 332 #define CFG_TSEC2_OFFSET 0x25000 333 #define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) 334 335 /* 336 * TSEC ethernet configuration 337 */ 338 #define CONFIG_MII 1 /* MII PHY management */ 339 #define CONFIG_TSEC1 1 340 #define CONFIG_TSEC1_NAME "eTSEC0" 341 #define CONFIG_TSEC2 1 342 #define CONFIG_TSEC2_NAME "eTSEC1" 343 #define TSEC1_PHY_ADDR 0 344 #define TSEC2_PHY_ADDR 1 345 #define TSEC1_PHYIDX 0 346 #define TSEC2_PHYIDX 0 347 #define TSEC1_FLAGS TSEC_GIGABIT 348 #define TSEC2_FLAGS TSEC_GIGABIT 349 350 /* Options are: eTSEC[0-1] */ 351 #define CONFIG_ETHPRIME "eTSEC1" 352 353 /* 354 * SATA 355 */ 356 #define CONFIG_LIBATA 357 #define CONFIG_FSL_SATA 358 359 #define CFG_SATA_MAX_DEVICE 2 360 #define CONFIG_SATA1 361 #define CFG_SATA1_OFFSET 0x18000 362 #define CFG_SATA1 (CFG_IMMR + CFG_SATA1_OFFSET) 363 #define CFG_SATA1_FLAGS FLAGS_DMA 364 #define CONFIG_SATA2 365 #define CFG_SATA2_OFFSET 0x19000 366 #define CFG_SATA2 (CFG_IMMR + CFG_SATA2_OFFSET) 367 #define CFG_SATA2_FLAGS FLAGS_DMA 368 369 #ifdef CONFIG_FSL_SATA 370 #define CONFIG_LBA48 371 #define CONFIG_CMD_SATA 372 #define CONFIG_DOS_PARTITION 373 #define CONFIG_CMD_EXT2 374 #endif 375 376 /* 377 * Environment 378 */ 379 #ifndef CFG_RAMBOOT 380 #define CONFIG_ENV_IS_IN_FLASH 1 381 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) 382 #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 383 #define CFG_ENV_SIZE 0x2000 384 #else 385 #define CFG_NO_FLASH 1 /* Flash is not usable now */ 386 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 387 #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) 388 #define CFG_ENV_SIZE 0x2000 389 #endif 390 391 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 392 #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 393 394 /* 395 * BOOTP options 396 */ 397 #define CONFIG_BOOTP_BOOTFILESIZE 398 #define CONFIG_BOOTP_BOOTPATH 399 #define CONFIG_BOOTP_GATEWAY 400 #define CONFIG_BOOTP_HOSTNAME 401 402 /* 403 * Command line configuration. 404 */ 405 #include <config_cmd_default.h> 406 407 #define CONFIG_CMD_PING 408 #define CONFIG_CMD_I2C 409 #define CONFIG_CMD_MII 410 #define CONFIG_CMD_DATE 411 #define CONFIG_CMD_PCI 412 413 #if defined(CFG_RAMBOOT) 414 #undef CONFIG_CMD_ENV 415 #undef CONFIG_CMD_LOADS 416 #endif 417 418 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 419 420 #undef CONFIG_WATCHDOG /* watchdog disabled */ 421 422 /* 423 * Miscellaneous configurable options 424 */ 425 #define CFG_LONGHELP /* undef to save memory */ 426 #define CFG_LOAD_ADDR 0x2000000 /* default load address */ 427 #define CFG_PROMPT "=> " /* Monitor Command Prompt */ 428 429 #if defined(CONFIG_CMD_KGDB) 430 #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ 431 #else 432 #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ 433 #endif 434 435 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ 436 #define CFG_MAXARGS 16 /* max number of command args */ 437 #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ 438 #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ 439 440 /* 441 * For booting Linux, the board info and command line data 442 * have to be in the first 8 MB of memory, since this is 443 * the maximum mapped by the Linux kernel during initialization. 444 */ 445 #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ 446 447 /* 448 * Core HID Setup 449 */ 450 #define CFG_HID0_INIT 0x000000000 451 #define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 452 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 453 #define CFG_HID2 HID2_HBE 454 455 /* 456 * MMU Setup 457 */ 458 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 459 460 /* DDR: cache cacheable */ 461 #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 462 #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP) 463 #define CFG_DBAT0L CFG_IBAT0L 464 #define CFG_DBAT0U CFG_IBAT0U 465 466 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 467 #define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \ 468 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 469 #define CFG_IBAT1U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) 470 #define CFG_DBAT1L CFG_IBAT1L 471 #define CFG_DBAT1U CFG_IBAT1U 472 473 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 474 #define CFG_IBAT2L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) 475 #define CFG_IBAT2U (CFG_FLASH_BASE | BATU_BL_8M | BATU_VS | BATU_VP) 476 #define CFG_DBAT2L (CFG_FLASH_BASE | BATL_PP_10 | \ 477 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 478 #define CFG_DBAT2U CFG_IBAT2U 479 480 /* Stack in dcache: cacheable, no memory coherence */ 481 #define CFG_IBAT3L (CFG_INIT_RAM_ADDR | BATL_PP_10) 482 #define CFG_IBAT3U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 483 #define CFG_DBAT3L CFG_IBAT3L 484 #define CFG_DBAT3U CFG_IBAT3U 485 486 /* PCI MEM space: cacheable */ 487 #define CFG_IBAT4L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) 488 #define CFG_IBAT4U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 489 #define CFG_DBAT4L CFG_IBAT4L 490 #define CFG_DBAT4U CFG_IBAT4U 491 492 /* PCI MMIO space: cache-inhibit and guarded */ 493 #define CFG_IBAT5L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ 494 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 495 #define CFG_IBAT5U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) 496 #define CFG_DBAT5L CFG_IBAT5L 497 #define CFG_DBAT5U CFG_IBAT5U 498 499 #define CFG_IBAT6L 0 500 #define CFG_IBAT6U 0 501 #define CFG_DBAT6L CFG_IBAT6L 502 #define CFG_DBAT6U CFG_IBAT6U 503 504 #define CFG_IBAT7L 0 505 #define CFG_IBAT7U 0 506 #define CFG_DBAT7L CFG_IBAT7L 507 #define CFG_DBAT7U CFG_IBAT7U 508 509 /* 510 * Internal Definitions 511 * 512 * Boot Flags 513 */ 514 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ 515 #define BOOTFLAG_WARM 0x02 /* Software reboot */ 516 517 #if defined(CONFIG_CMD_KGDB) 518 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 519 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 520 #endif 521 522 /* 523 * Environment Configuration 524 */ 525 526 #define CONFIG_ENV_OVERWRITE 527 528 #if defined(CONFIG_TSEC_ENET) 529 #define CONFIG_HAS_ETH0 530 #define CONFIG_ETHADDR 04:00:00:00:00:0A 531 #define CONFIG_HAS_ETH1 532 #define CONFIG_ETH1ADDR 04:00:00:00:00:0B 533 #endif 534 535 #define CONFIG_BAUDRATE 115200 536 537 #define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */ 538 539 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 540 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 541 542 #define CONFIG_EXTRA_ENV_SETTINGS \ 543 "netdev=eth0\0" \ 544 "consoledev=ttyS0\0" \ 545 "ramdiskaddr=1000000\0" \ 546 "ramdiskfile=ramfs.83xx\0" \ 547 "fdtaddr=400000\0" \ 548 "fdtfile=mpc8315erdb.dtb\0" \ 549 "" 550 551 #define CONFIG_NFSBOOTCOMMAND \ 552 "setenv bootargs root=/dev/nfs rw " \ 553 "nfsroot=$serverip:$rootpath " \ 554 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 555 "console=$consoledev,$baudrate $othbootargs;" \ 556 "tftp $loadaddr $bootfile;" \ 557 "tftp $fdtaddr $fdtfile;" \ 558 "bootm $loadaddr - $fdtaddr" 559 560 #define CONFIG_RAMBOOTCOMMAND \ 561 "setenv bootargs root=/dev/ram rw " \ 562 "console=$consoledev,$baudrate $othbootargs;" \ 563 "tftp $ramdiskaddr $ramdiskfile;" \ 564 "tftp $loadaddr $bootfile;" \ 565 "tftp $fdtaddr $fdtfile;" \ 566 "bootm $loadaddr $ramdiskaddr $fdtaddr" 567 568 569 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 570 571 #endif /* __CONFIG_H */ 572