1 /*
2  * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
3  *
4  * Dave Liu <daveliu@freescale.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 #ifndef __CONFIG_H
10 #define __CONFIG_H
11 
12 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
13 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
14 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
15 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
16 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
17 
18 #ifndef CONFIG_SYS_TEXT_BASE
19 #define CONFIG_SYS_TEXT_BASE	0xFE000000
20 #endif
21 
22 #ifndef CONFIG_SYS_MONITOR_BASE
23 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
24 #endif
25 
26 /*
27  * High Level Configuration Options
28  */
29 #define CONFIG_E300		1 /* E300 family */
30 #define CONFIG_MPC831x		1 /* MPC831x CPU family */
31 #define CONFIG_MPC8315		1 /* MPC8315 CPU specific */
32 #define CONFIG_MPC8315ERDB	1 /* MPC8315ERDB board specific */
33 
34 /*
35  * System Clock Setup
36  */
37 #define CONFIG_83XX_CLKIN	66666667 /* in Hz */
38 #define CONFIG_SYS_CLK_FREQ	CONFIG_83XX_CLKIN
39 
40 /*
41  * Hardware Reset Configuration Word
42  * if CLKIN is 66.66MHz, then
43  * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz
44  */
45 #define CONFIG_SYS_HRCW_LOW (\
46 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
47 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
48 	HRCWL_SVCOD_DIV_2 |\
49 	HRCWL_CSB_TO_CLKIN_2X1 |\
50 	HRCWL_CORE_TO_CSB_3X1)
51 #define CONFIG_SYS_HRCW_HIGH_BASE (\
52 	HRCWH_PCI_HOST |\
53 	HRCWH_PCI1_ARBITER_ENABLE |\
54 	HRCWH_CORE_ENABLE |\
55 	HRCWH_BOOTSEQ_DISABLE |\
56 	HRCWH_SW_WATCHDOG_DISABLE |\
57 	HRCWH_TSEC1M_IN_RGMII |\
58 	HRCWH_TSEC2M_IN_RGMII |\
59 	HRCWH_BIG_ENDIAN |\
60 	HRCWH_LALE_NORMAL)
61 
62 #ifdef CONFIG_NAND_SPL
63 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
64 		       HRCWH_FROM_0XFFF00100 |\
65 		       HRCWH_ROM_LOC_NAND_SP_8BIT |\
66 		       HRCWH_RL_EXT_NAND)
67 #else
68 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\
69 		       HRCWH_FROM_0X00000100 |\
70 		       HRCWH_ROM_LOC_LOCAL_16BIT |\
71 		       HRCWH_RL_EXT_LEGACY)
72 #endif
73 
74 /*
75  * System IO Config
76  */
77 #define CONFIG_SYS_SICRH		0x00000000
78 #define CONFIG_SYS_SICRL		0x00000000 /* 3.3V, no delay */
79 
80 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
81 #define CONFIG_HWCONFIG
82 
83 /*
84  * IMMR new address
85  */
86 #define CONFIG_SYS_IMMR		0xE0000000
87 
88 /*
89  * Arbiter Setup
90  */
91 #define CONFIG_SYS_ACR_PIPE_DEP	3 /* Arbiter pipeline depth is 4 */
92 #define CONFIG_SYS_ACR_RPTCNT	3 /* Arbiter repeat count is 4 */
93 #define CONFIG_SYS_SPCR_TSECEP	3 /* eTSEC emergency priority is highest */
94 
95 /*
96  * DDR Setup
97  */
98 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
99 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
100 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
101 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
102 #define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
103 				| DDRCDR_PZ_LOZ \
104 				| DDRCDR_NZ_LOZ \
105 				| DDRCDR_ODT \
106 				| DDRCDR_Q_DRN)
107 				/* 0x7b880001 */
108 /*
109  * Manually set up DDR parameters
110  * consist of two chips HY5PS12621BFP-C4 from HYNIX
111  */
112 #define CONFIG_SYS_DDR_SIZE		128 /* MB */
113 #define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
114 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
115 				| CSCONFIG_ODT_RD_NEVER \
116 				| CSCONFIG_ODT_WR_ONLY_CURRENT \
117 				| CSCONFIG_ROW_BIT_13 \
118 				| CSCONFIG_COL_BIT_10)
119 				/* 0x80010102 */
120 #define CONFIG_SYS_DDR_TIMING_3	0x00000000
121 #define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
122 				| (0 << TIMING_CFG0_WRT_SHIFT) \
123 				| (0 << TIMING_CFG0_RRT_SHIFT) \
124 				| (0 << TIMING_CFG0_WWT_SHIFT) \
125 				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
126 				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
127 				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
128 				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
129 				/* 0x00220802 */
130 #define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
131 				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
132 				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
133 				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
134 				| (6 << TIMING_CFG1_REFREC_SHIFT) \
135 				| (2 << TIMING_CFG1_WRREC_SHIFT) \
136 				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
137 				| (2 << TIMING_CFG1_WRTORD_SHIFT))
138 				/* 0x27256222 */
139 #define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
140 				| (4 << TIMING_CFG2_CPO_SHIFT) \
141 				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
142 				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
143 				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
144 				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
145 				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
146 				/* 0x121048c5 */
147 #define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
148 				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
149 				/* 0x03600100 */
150 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
151 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
152 				| SDRAM_CFG_DBW_32)
153 				/* 0x43080000 */
154 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
155 #define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
156 				| (0x0232 << SDRAM_MODE_SD_SHIFT))
157 				/* ODT 150ohm CL=3, AL=1 on SDRAM */
158 #define CONFIG_SYS_DDR_MODE2	0x00000000
159 
160 /*
161  * Memory test
162  */
163 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
164 #define CONFIG_SYS_MEMTEST_START	0x00040000 /* memtest region */
165 #define CONFIG_SYS_MEMTEST_END		0x00140000
166 
167 /*
168  * The reserved memory
169  */
170 #define CONFIG_SYS_MONITOR_LEN	(512 * 1024) /* Reserve 512 kB for Mon */
171 #define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
172 
173 /*
174  * Initial RAM Base Address Setup
175  */
176 #define CONFIG_SYS_INIT_RAM_LOCK	1
177 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
178 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
179 #define CONFIG_SYS_GBL_DATA_OFFSET	\
180 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
181 
182 /*
183  * Local Bus Configuration & Clock Setup
184  */
185 #define CONFIG_SYS_LCRR_DBYP	LCRR_DBYP
186 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
187 #define CONFIG_SYS_LBC_LBCR		0x00040000
188 #define CONFIG_FSL_ELBC		1
189 
190 /*
191  * FLASH on the Local Bus
192  */
193 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
194 #define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
195 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
196 
197 #define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
198 #define CONFIG_SYS_FLASH_SIZE		8	/* FLASH size is 8M */
199 #define CONFIG_SYS_FLASH_PROTECTION	1	/* Use h/w Flash protection. */
200 
201 					/* Window base at flash base */
202 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
203 #define CONFIG_SYS_LBLAWAR0_PRELIM	(LBLAWAR_EN | LBLAWAR_8MB)
204 
205 #define CONFIG_SYS_NOR_BR_PRELIM	(CONFIG_SYS_FLASH_BASE \
206 					| BR_PS_16	/* 16 bit port */ \
207 					| BR_MS_GPCM	/* MSEL = GPCM */ \
208 					| BR_V)		/* valid */
209 #define CONFIG_SYS_NOR_OR_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
210 					| OR_UPM_XAM \
211 					| OR_GPCM_CSNT \
212 					| OR_GPCM_ACS_DIV2 \
213 					| OR_GPCM_XACS \
214 					| OR_GPCM_SCY_15 \
215 					| OR_GPCM_TRLX_SET \
216 					| OR_GPCM_EHTR_SET \
217 					| OR_GPCM_EAD)
218 
219 #define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
220 /* 127 64KB sectors and 8 8KB top sectors per device */
221 #define CONFIG_SYS_MAX_FLASH_SECT	135
222 
223 #undef CONFIG_SYS_FLASH_CHECKSUM
224 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
225 #define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
226 
227 /*
228  * NAND Flash on the Local Bus
229  */
230 
231 #ifdef CONFIG_NAND_SPL
232 #define CONFIG_SYS_NAND_BASE		0xFFF00000
233 #else
234 #define CONFIG_SYS_NAND_BASE		0xE0600000
235 #endif
236 
237 #define CONFIG_MTD_DEVICE
238 #define CONFIG_MTD_PARTITION
239 #define CONFIG_CMD_MTDPARTS
240 #define MTDIDS_DEFAULT			"nand0=e0600000.flash"
241 #define MTDPARTS_DEFAULT		\
242 	"mtdparts=e0600000.flash:512k(uboot),128k(env),6m@1m(kernel),-(fs)"
243 
244 #define CONFIG_SYS_MAX_NAND_DEVICE	1
245 #define CONFIG_CMD_NAND			1
246 #define CONFIG_NAND_FSL_ELBC		1
247 #define CONFIG_SYS_NAND_BLOCK_SIZE	16384
248 #define CONFIG_SYS_NAND_WINDOW_SIZE    (32 * 1024)     /* 0x00008000 */
249 
250 #define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
251 #define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
252 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
253 #define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
254 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
255 
256 #define CONFIG_SYS_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE \
257 				| BR_DECC_CHK_GEN	/* Use HW ECC */ \
258 				| BR_PS_8		/* 8 bit port */ \
259 				| BR_MS_FCM		/* MSEL = FCM */ \
260 				| BR_V)			/* valid */
261 #define CONFIG_SYS_NAND_OR_PRELIM	\
262 				(P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
263 				| OR_FCM_CSCT \
264 				| OR_FCM_CST \
265 				| OR_FCM_CHT \
266 				| OR_FCM_SCY_1 \
267 				| OR_FCM_TRLX \
268 				| OR_FCM_EHTR)
269 				/* 0xFFFF8396 */
270 
271 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
272 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
273 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
274 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
275 
276 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
277 #define CONFIG_SYS_LBLAWAR1_PRELIM	(LBLAWAR_EN | LBLAWAR_32KB)
278 
279 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
280 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
281 
282 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
283 	!defined(CONFIG_NAND_SPL)
284 #define CONFIG_SYS_RAMBOOT
285 #else
286 #undef CONFIG_SYS_RAMBOOT
287 #endif
288 
289 /*
290  * Serial Port
291  */
292 #define CONFIG_CONS_INDEX	1
293 #define CONFIG_SYS_NS16550_SERIAL
294 #define CONFIG_SYS_NS16550_REG_SIZE	1
295 #define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
296 
297 #define CONFIG_SYS_BAUDRATE_TABLE  \
298 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
299 
300 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
301 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
302 
303 /* I2C */
304 #define CONFIG_SYS_I2C
305 #define CONFIG_SYS_I2C_FSL
306 #define CONFIG_SYS_FSL_I2C_SPEED	400000
307 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
308 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
309 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }
310 
311 /*
312  * Board info - revision and where boot from
313  */
314 #define CONFIG_SYS_I2C_PCF8574A_ADDR	0x39
315 
316 /*
317  * Config on-board RTC
318  */
319 #define CONFIG_RTC_DS1337	/* ds1339 on board, use ds1337 rtc via i2c */
320 #define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
321 
322 /*
323  * General PCI
324  * Addresses are mapped 1-1.
325  */
326 #define CONFIG_SYS_PCI_MEM_BASE		0x80000000
327 #define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
328 #define CONFIG_SYS_PCI_MEM_SIZE		0x10000000 /* 256M */
329 #define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
330 #define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
331 #define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
332 #define CONFIG_SYS_PCI_IO_BASE		0x00000000
333 #define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
334 #define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */
335 
336 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
337 #define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
338 #define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
339 
340 #define CONFIG_SYS_PCIE1_BASE		0xA0000000
341 #define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
342 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
343 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
344 #define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
345 #define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
346 #define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
347 #define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
348 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
349 
350 #define CONFIG_SYS_PCIE2_BASE		0xC0000000
351 #define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
352 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
353 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
354 #define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
355 #define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
356 #define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
357 #define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
358 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
359 
360 #define CONFIG_PCI_INDIRECT_BRIDGE
361 #define CONFIG_PCIE
362 
363 #define CONFIG_EEPRO100
364 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
365 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
366 
367 #define CONFIG_HAS_FSL_DR_USB
368 #define CONFIG_SYS_SCCR_USBDRCM		3
369 
370 #define CONFIG_USB_EHCI
371 #define CONFIG_USB_EHCI_FSL
372 #define CONFIG_USB_PHY_TYPE	"utmi"
373 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
374 
375 /*
376  * TSEC
377  */
378 #define CONFIG_TSEC_ENET	/* TSEC ethernet support */
379 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
380 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
381 #define CONFIG_SYS_TSEC2_OFFSET	0x25000
382 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
383 
384 /*
385  * TSEC ethernet configuration
386  */
387 #define CONFIG_MII		1 /* MII PHY management */
388 #define CONFIG_TSEC1		1
389 #define CONFIG_TSEC1_NAME	"eTSEC0"
390 #define CONFIG_TSEC2		1
391 #define CONFIG_TSEC2_NAME	"eTSEC1"
392 #define TSEC1_PHY_ADDR		0
393 #define TSEC2_PHY_ADDR		1
394 #define TSEC1_PHYIDX		0
395 #define TSEC2_PHYIDX		0
396 #define TSEC1_FLAGS		TSEC_GIGABIT
397 #define TSEC2_FLAGS		TSEC_GIGABIT
398 
399 /* Options are: eTSEC[0-1] */
400 #define CONFIG_ETHPRIME		"eTSEC1"
401 
402 /*
403  * SATA
404  */
405 #define CONFIG_LIBATA
406 #define CONFIG_FSL_SATA
407 
408 #define CONFIG_SYS_SATA_MAX_DEVICE	2
409 #define CONFIG_SATA1
410 #define CONFIG_SYS_SATA1_OFFSET	0x18000
411 #define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
412 #define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
413 #define CONFIG_SATA2
414 #define CONFIG_SYS_SATA2_OFFSET	0x19000
415 #define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
416 #define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA
417 
418 #ifdef CONFIG_FSL_SATA
419 #define CONFIG_LBA48
420 #define CONFIG_CMD_SATA
421 #define CONFIG_DOS_PARTITION
422 #endif
423 
424 /*
425  * Environment
426  */
427 #if !defined(CONFIG_SYS_RAMBOOT)
428 	#define CONFIG_ENV_IS_IN_FLASH	1
429 	#define CONFIG_ENV_ADDR		\
430 			(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
431 	#define CONFIG_ENV_SECT_SIZE	0x10000 /* 64K(one sector) for env */
432 	#define CONFIG_ENV_SIZE		0x2000
433 #else
434 	#define CONFIG_SYS_NO_FLASH	1	/* Flash is not usable now */
435 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
436 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
437 	#define CONFIG_ENV_SIZE		0x2000
438 #endif
439 
440 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
441 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
442 
443 /*
444  * BOOTP options
445  */
446 #define CONFIG_BOOTP_BOOTFILESIZE
447 #define CONFIG_BOOTP_BOOTPATH
448 #define CONFIG_BOOTP_GATEWAY
449 #define CONFIG_BOOTP_HOSTNAME
450 
451 /*
452  * Command line configuration.
453  */
454 #define CONFIG_CMD_DATE
455 #define CONFIG_CMD_PCI
456 
457 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
458 #define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
459 
460 #undef CONFIG_WATCHDOG		/* watchdog disabled */
461 
462 /*
463  * Miscellaneous configurable options
464  */
465 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
466 #define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
467 
468 #if defined(CONFIG_CMD_KGDB)
469 	#define CONFIG_SYS_CBSIZE	1024 /* Console I/O Buffer Size */
470 #else
471 	#define CONFIG_SYS_CBSIZE	256 /* Console I/O Buffer Size */
472 #endif
473 
474 				/* Print Buffer Size */
475 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
476 #define CONFIG_SYS_MAXARGS	16	/* max number of command args */
477 				/* Boot Argument Buffer Size */
478 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
479 
480 /*
481  * For booting Linux, the board info and command line data
482  * have to be in the first 256 MB of memory, since this is
483  * the maximum mapped by the Linux kernel during initialization.
484  */
485 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
486 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
487 
488 /*
489  * Core HID Setup
490  */
491 #define CONFIG_SYS_HID0_INIT	0x000000000
492 #define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK | \
493 				 HID0_ENABLE_INSTRUCTION_CACHE | \
494 				 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
495 #define CONFIG_SYS_HID2		HID2_HBE
496 
497 /*
498  * MMU Setup
499  */
500 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
501 
502 /* DDR: cache cacheable */
503 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE \
504 				| BATL_PP_RW \
505 				| BATL_MEMCOHERENCE)
506 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE \
507 				| BATU_BL_128M \
508 				| BATU_VS \
509 				| BATU_VP)
510 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
511 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
512 
513 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
514 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR \
515 				| BATL_PP_RW \
516 				| BATL_CACHEINHIBIT \
517 				| BATL_GUARDEDSTORAGE)
518 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR \
519 				| BATU_BL_8M \
520 				| BATU_VS \
521 				| BATU_VP)
522 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
523 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
524 
525 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
526 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE \
527 				| BATL_PP_RW \
528 				| BATL_MEMCOHERENCE)
529 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE \
530 				| BATU_BL_32M \
531 				| BATU_VS \
532 				| BATU_VP)
533 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE \
534 				| BATL_PP_RW \
535 				| BATL_CACHEINHIBIT \
536 				| BATL_GUARDEDSTORAGE)
537 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
538 
539 /* Stack in dcache: cacheable, no memory coherence */
540 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
541 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_INIT_RAM_ADDR \
542 				| BATU_BL_128K \
543 				| BATU_VS \
544 				| BATU_VP)
545 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
546 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
547 
548 /* PCI MEM space: cacheable */
549 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI_MEM_PHYS \
550 				| BATL_PP_RW \
551 				| BATL_MEMCOHERENCE)
552 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI_MEM_PHYS \
553 				| BATU_BL_256M \
554 				| BATU_VS \
555 				| BATU_VP)
556 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
557 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
558 
559 /* PCI MMIO space: cache-inhibit and guarded */
560 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI_MMIO_PHYS \
561 				| BATL_PP_RW \
562 				| BATL_CACHEINHIBIT \
563 				| BATL_GUARDEDSTORAGE)
564 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI_MMIO_PHYS \
565 				| BATU_BL_256M \
566 				| BATU_VS \
567 				| BATU_VP)
568 #define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
569 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
570 
571 #define CONFIG_SYS_IBAT6L	0
572 #define CONFIG_SYS_IBAT6U	0
573 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
574 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
575 
576 #define CONFIG_SYS_IBAT7L	0
577 #define CONFIG_SYS_IBAT7U	0
578 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
579 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
580 
581 #if defined(CONFIG_CMD_KGDB)
582 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
583 #endif
584 
585 /*
586  * Environment Configuration
587  */
588 
589 #define CONFIG_ENV_OVERWRITE
590 
591 #if defined(CONFIG_TSEC_ENET)
592 #define CONFIG_HAS_ETH0
593 #define CONFIG_HAS_ETH1
594 #endif
595 
596 #define CONFIG_BAUDRATE 115200
597 
598 #define CONFIG_LOADADDR 800000	/* default location for tftp and bootm */
599 
600 #undef CONFIG_BOOTARGS		/* the boot command will set bootargs */
601 
602 #define CONFIG_EXTRA_ENV_SETTINGS					\
603 	"netdev=eth0\0"							\
604 	"consoledev=ttyS0\0"						\
605 	"ramdiskaddr=1000000\0"						\
606 	"ramdiskfile=ramfs.83xx\0"					\
607 	"fdtaddr=780000\0"						\
608 	"fdtfile=mpc8315erdb.dtb\0"					\
609 	"usb_phy_type=utmi\0"						\
610 	""
611 
612 #define CONFIG_NFSBOOTCOMMAND						\
613 	"setenv bootargs root=/dev/nfs rw "				\
614 		"nfsroot=$serverip:$rootpath "				\
615 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
616 							"$netdev:off "	\
617 		"console=$consoledev,$baudrate $othbootargs;"		\
618 	"tftp $loadaddr $bootfile;"					\
619 	"tftp $fdtaddr $fdtfile;"					\
620 	"bootm $loadaddr - $fdtaddr"
621 
622 #define CONFIG_RAMBOOTCOMMAND						\
623 	"setenv bootargs root=/dev/ram rw "				\
624 		"console=$consoledev,$baudrate $othbootargs;"		\
625 	"tftp $ramdiskaddr $ramdiskfile;"				\
626 	"tftp $loadaddr $bootfile;"					\
627 	"tftp $fdtaddr $fdtfile;"					\
628 	"bootm $loadaddr $ramdiskaddr $fdtaddr"
629 
630 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
631 
632 #endif	/* __CONFIG_H */
633