1 /* 2 * Copyright (C) 2007-2010 Freescale Semiconductor, Inc. 3 * 4 * Dave Liu <daveliu@freescale.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #ifndef __CONFIG_H 10 #define __CONFIG_H 11 12 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) 13 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 14 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 15 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 16 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 17 18 #ifdef CONFIG_NAND_U_BOOT 19 #define CONFIG_SYS_TEXT_BASE 0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */ 20 #define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 21 #ifdef CONFIG_NAND_SPL 22 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ 23 #endif /* CONFIG_NAND_SPL */ 24 #endif /* CONFIG_NAND_U_BOOT */ 25 26 #ifndef CONFIG_SYS_TEXT_BASE 27 #define CONFIG_SYS_TEXT_BASE 0xFE000000 28 #endif 29 30 #ifndef CONFIG_SYS_MONITOR_BASE 31 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 32 #endif 33 34 /* 35 * High Level Configuration Options 36 */ 37 #define CONFIG_E300 1 /* E300 family */ 38 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 39 #define CONFIG_MPC831x 1 /* MPC831x CPU family */ 40 #define CONFIG_MPC8315 1 /* MPC8315 CPU specific */ 41 #define CONFIG_MPC8315ERDB 1 /* MPC8315ERDB board specific */ 42 43 /* 44 * System Clock Setup 45 */ 46 #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ 47 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 48 49 /* 50 * Hardware Reset Configuration Word 51 * if CLKIN is 66.66MHz, then 52 * CSB = 133MHz, CORE = 400MHz, DDRC = 266MHz, LBC = 133MHz 53 */ 54 #define CONFIG_SYS_HRCW_LOW (\ 55 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 56 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 57 HRCWL_SVCOD_DIV_2 |\ 58 HRCWL_CSB_TO_CLKIN_2X1 |\ 59 HRCWL_CORE_TO_CSB_3X1) 60 #define CONFIG_SYS_HRCW_HIGH_BASE (\ 61 HRCWH_PCI_HOST |\ 62 HRCWH_PCI1_ARBITER_ENABLE |\ 63 HRCWH_CORE_ENABLE |\ 64 HRCWH_BOOTSEQ_DISABLE |\ 65 HRCWH_SW_WATCHDOG_DISABLE |\ 66 HRCWH_TSEC1M_IN_RGMII |\ 67 HRCWH_TSEC2M_IN_RGMII |\ 68 HRCWH_BIG_ENDIAN |\ 69 HRCWH_LALE_NORMAL) 70 71 #ifdef CONFIG_NAND_SPL 72 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 73 HRCWH_FROM_0XFFF00100 |\ 74 HRCWH_ROM_LOC_NAND_SP_8BIT |\ 75 HRCWH_RL_EXT_NAND) 76 #else 77 #define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ 78 HRCWH_FROM_0X00000100 |\ 79 HRCWH_ROM_LOC_LOCAL_16BIT |\ 80 HRCWH_RL_EXT_LEGACY) 81 #endif 82 83 /* 84 * System IO Config 85 */ 86 #define CONFIG_SYS_SICRH 0x00000000 87 #define CONFIG_SYS_SICRL 0x00000000 /* 3.3V, no delay */ 88 89 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ 90 #define CONFIG_HWCONFIG 91 92 /* 93 * IMMR new address 94 */ 95 #define CONFIG_SYS_IMMR 0xE0000000 96 97 #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) 98 #define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR 99 #endif 100 101 /* 102 * Arbiter Setup 103 */ 104 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 105 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 106 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 107 108 /* 109 * DDR Setup 110 */ 111 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 112 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 113 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 114 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 115 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 116 | DDRCDR_PZ_LOZ \ 117 | DDRCDR_NZ_LOZ \ 118 | DDRCDR_ODT \ 119 | DDRCDR_Q_DRN) 120 /* 0x7b880001 */ 121 /* 122 * Manually set up DDR parameters 123 * consist of two chips HY5PS12621BFP-C4 from HYNIX 124 */ 125 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 126 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 127 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 128 | CSCONFIG_ODT_RD_NEVER \ 129 | CSCONFIG_ODT_WR_ONLY_CURRENT \ 130 | CSCONFIG_ROW_BIT_13 \ 131 | CSCONFIG_COL_BIT_10) 132 /* 0x80010102 */ 133 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 134 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 135 | (0 << TIMING_CFG0_WRT_SHIFT) \ 136 | (0 << TIMING_CFG0_RRT_SHIFT) \ 137 | (0 << TIMING_CFG0_WWT_SHIFT) \ 138 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 139 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 140 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 141 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 142 /* 0x00220802 */ 143 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 144 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 145 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 146 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 147 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 148 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 149 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 150 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 151 /* 0x27256222 */ 152 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 153 | (4 << TIMING_CFG2_CPO_SHIFT) \ 154 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 155 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 156 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 157 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 158 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 159 /* 0x121048c5 */ 160 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 161 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 162 /* 0x03600100 */ 163 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 164 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 165 | SDRAM_CFG_DBW_32) 166 /* 0x43080000 */ 167 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 168 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 169 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 170 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 171 #define CONFIG_SYS_DDR_MODE2 0x00000000 172 173 /* 174 * Memory test 175 */ 176 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 177 #define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ 178 #define CONFIG_SYS_MEMTEST_END 0x00140000 179 180 /* 181 * The reserved memory 182 */ 183 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 184 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 185 186 /* 187 * Initial RAM Base Address Setup 188 */ 189 #define CONFIG_SYS_INIT_RAM_LOCK 1 190 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 191 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 192 #define CONFIG_SYS_GBL_DATA_OFFSET \ 193 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 194 195 /* 196 * Local Bus Configuration & Clock Setup 197 */ 198 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 199 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 200 #define CONFIG_SYS_LBC_LBCR 0x00040000 201 #define CONFIG_FSL_ELBC 1 202 203 /* 204 * FLASH on the Local Bus 205 */ 206 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 207 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 208 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 209 210 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 211 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ 212 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 213 214 /* Window base at flash base */ 215 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 216 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 217 218 #define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE \ 219 | BR_PS_16 /* 16 bit port */ \ 220 | BR_MS_GPCM /* MSEL = GPCM */ \ 221 | BR_V) /* valid */ 222 #define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 223 | OR_UPM_XAM \ 224 | OR_GPCM_CSNT \ 225 | OR_GPCM_ACS_DIV2 \ 226 | OR_GPCM_XACS \ 227 | OR_GPCM_SCY_15 \ 228 | OR_GPCM_TRLX_SET \ 229 | OR_GPCM_EHTR_SET \ 230 | OR_GPCM_EAD) 231 232 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 233 /* 127 64KB sectors and 8 8KB top sectors per device */ 234 #define CONFIG_SYS_MAX_FLASH_SECT 135 235 236 #undef CONFIG_SYS_FLASH_CHECKSUM 237 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 238 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 239 240 /* 241 * NAND Flash on the Local Bus 242 */ 243 244 #ifdef CONFIG_NAND_SPL 245 #define CONFIG_SYS_NAND_BASE 0xFFF00000 246 #else 247 #define CONFIG_SYS_NAND_BASE 0xE0600000 248 #endif 249 250 #define CONFIG_MTD_DEVICE 251 #define CONFIG_MTD_PARTITION 252 #define CONFIG_CMD_MTDPARTS 253 #define MTDIDS_DEFAULT "nand0=e0600000.flash" 254 #define MTDPARTS_DEFAULT \ 255 "mtdparts=e0600000.flash:512k(uboot),128k(env),3m@1m(kernel),-(fs)" 256 257 #define CONFIG_SYS_MAX_NAND_DEVICE 1 258 #define CONFIG_MTD_NAND_VERIFY_WRITE 1 259 #define CONFIG_CMD_NAND 1 260 #define CONFIG_NAND_FSL_ELBC 1 261 #define CONFIG_SYS_NAND_BLOCK_SIZE 16384 262 #define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */ 263 264 #define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) 265 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 266 #define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 267 #define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 268 #define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 269 270 #define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ 271 | BR_DECC_CHK_GEN /* Use HW ECC */ \ 272 | BR_PS_8 /* 8 bit port */ \ 273 | BR_MS_FCM /* MSEL = FCM */ \ 274 | BR_V) /* valid */ 275 #define CONFIG_SYS_NAND_OR_PRELIM \ 276 (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \ 277 | OR_FCM_CSCT \ 278 | OR_FCM_CST \ 279 | OR_FCM_CHT \ 280 | OR_FCM_SCY_1 \ 281 | OR_FCM_TRLX \ 282 | OR_FCM_EHTR) 283 /* 0xFFFF8396 */ 284 285 #ifdef CONFIG_NAND_U_BOOT 286 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM 287 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM 288 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM 289 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM 290 #else 291 #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM 292 #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM 293 #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM 294 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM 295 #endif 296 297 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 298 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 299 300 #define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM 301 #define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM 302 303 #if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \ 304 !defined(CONFIG_NAND_SPL) 305 #define CONFIG_SYS_RAMBOOT 306 #else 307 #undef CONFIG_SYS_RAMBOOT 308 #endif 309 310 /* 311 * Serial Port 312 */ 313 #define CONFIG_CONS_INDEX 1 314 #define CONFIG_SYS_NS16550 315 #define CONFIG_SYS_NS16550_SERIAL 316 #define CONFIG_SYS_NS16550_REG_SIZE 1 317 #define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) 318 319 #define CONFIG_SYS_BAUDRATE_TABLE \ 320 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 321 322 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) 323 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) 324 325 /* Use the HUSH parser */ 326 #define CONFIG_SYS_HUSH_PARSER 327 328 /* Pass open firmware flat tree */ 329 #define CONFIG_OF_LIBFDT 1 330 #define CONFIG_OF_BOARD_SETUP 1 331 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 332 333 /* I2C */ 334 #define CONFIG_HARD_I2C /* I2C with hardware support */ 335 #define CONFIG_FSL_I2C 336 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave addr */ 337 #define CONFIG_SYS_I2C_SLAVE 0x7F 338 #define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ 339 #define CONFIG_SYS_I2C_OFFSET 0x3000 340 #define CONFIG_SYS_I2C2_OFFSET 0x3100 341 342 /* 343 * Board info - revision and where boot from 344 */ 345 #define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 346 347 /* 348 * Config on-board RTC 349 */ 350 #define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ 351 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 352 353 /* 354 * General PCI 355 * Addresses are mapped 1-1. 356 */ 357 #define CONFIG_SYS_PCI_MEM_BASE 0x80000000 358 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE 359 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ 360 #define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 361 #define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE 362 #define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ 363 #define CONFIG_SYS_PCI_IO_BASE 0x00000000 364 #define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 365 #define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ 366 367 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE 368 #define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 369 #define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 370 371 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 372 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 373 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 374 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 375 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 376 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 377 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 378 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 379 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 380 381 #define CONFIG_SYS_PCIE2_BASE 0xC0000000 382 #define CONFIG_SYS_PCIE2_MEM_BASE 0xC0000000 383 #define CONFIG_SYS_PCIE2_MEM_PHYS 0xC0000000 384 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 385 #define CONFIG_SYS_PCIE2_CFG_BASE 0xD0000000 386 #define CONFIG_SYS_PCIE2_CFG_SIZE 0x01000000 387 #define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 388 #define CONFIG_SYS_PCIE2_IO_PHYS 0xD1000000 389 #define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 390 391 #define CONFIG_PCI 392 #define CONFIG_PCI_INDIRECT_BRIDGE 393 #define CONFIG_PCIE 394 395 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 396 397 #define CONFIG_EEPRO100 398 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 399 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 400 401 #define CONFIG_HAS_FSL_DR_USB 402 #define CONFIG_SYS_SCCR_USBDRCM 3 403 404 #define CONFIG_CMD_USB 405 #define CONFIG_USB_STORAGE 406 #define CONFIG_USB_EHCI 407 #define CONFIG_USB_EHCI_FSL 408 #define CONFIG_USB_PHY_TYPE "utmi" 409 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 410 411 /* 412 * TSEC 413 */ 414 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 415 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 416 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 417 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 418 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 419 420 /* 421 * TSEC ethernet configuration 422 */ 423 #define CONFIG_MII 1 /* MII PHY management */ 424 #define CONFIG_TSEC1 1 425 #define CONFIG_TSEC1_NAME "eTSEC0" 426 #define CONFIG_TSEC2 1 427 #define CONFIG_TSEC2_NAME "eTSEC1" 428 #define TSEC1_PHY_ADDR 0 429 #define TSEC2_PHY_ADDR 1 430 #define TSEC1_PHYIDX 0 431 #define TSEC2_PHYIDX 0 432 #define TSEC1_FLAGS TSEC_GIGABIT 433 #define TSEC2_FLAGS TSEC_GIGABIT 434 435 /* Options are: eTSEC[0-1] */ 436 #define CONFIG_ETHPRIME "eTSEC1" 437 438 /* 439 * SATA 440 */ 441 #define CONFIG_LIBATA 442 #define CONFIG_FSL_SATA 443 444 #define CONFIG_SYS_SATA_MAX_DEVICE 2 445 #define CONFIG_SATA1 446 #define CONFIG_SYS_SATA1_OFFSET 0x18000 447 #define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) 448 #define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA 449 #define CONFIG_SATA2 450 #define CONFIG_SYS_SATA2_OFFSET 0x19000 451 #define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) 452 #define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA 453 454 #ifdef CONFIG_FSL_SATA 455 #define CONFIG_LBA48 456 #define CONFIG_CMD_SATA 457 #define CONFIG_DOS_PARTITION 458 #define CONFIG_CMD_EXT2 459 #endif 460 461 /* 462 * Environment 463 */ 464 #if defined(CONFIG_NAND_U_BOOT) 465 #define CONFIG_ENV_IS_IN_NAND 1 466 #define CONFIG_ENV_OFFSET (512 * 1024) 467 #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE 468 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE 469 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 470 #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) 471 #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ 472 CONFIG_ENV_RANGE) 473 #elif !defined(CONFIG_SYS_RAMBOOT) 474 #define CONFIG_ENV_IS_IN_FLASH 1 475 #define CONFIG_ENV_ADDR \ 476 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 477 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 478 #define CONFIG_ENV_SIZE 0x2000 479 #else 480 #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ 481 #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ 482 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 483 #define CONFIG_ENV_SIZE 0x2000 484 #endif 485 486 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 487 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 488 489 /* 490 * BOOTP options 491 */ 492 #define CONFIG_BOOTP_BOOTFILESIZE 493 #define CONFIG_BOOTP_BOOTPATH 494 #define CONFIG_BOOTP_GATEWAY 495 #define CONFIG_BOOTP_HOSTNAME 496 497 /* 498 * Command line configuration. 499 */ 500 #include <config_cmd_default.h> 501 502 #define CONFIG_CMD_PING 503 #define CONFIG_CMD_I2C 504 #define CONFIG_CMD_MII 505 #define CONFIG_CMD_DATE 506 #define CONFIG_CMD_PCI 507 508 #if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) 509 #undef CONFIG_CMD_SAVEENV 510 #undef CONFIG_CMD_LOADS 511 #endif 512 513 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 514 #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ 515 516 #undef CONFIG_WATCHDOG /* watchdog disabled */ 517 518 /* 519 * Miscellaneous configurable options 520 */ 521 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 522 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 523 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 524 525 #if defined(CONFIG_CMD_KGDB) 526 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 527 #else 528 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 529 #endif 530 531 /* Print Buffer Size */ 532 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) 533 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 534 /* Boot Argument Buffer Size */ 535 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 536 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 537 538 /* 539 * For booting Linux, the board info and command line data 540 * have to be in the first 256 MB of memory, since this is 541 * the maximum mapped by the Linux kernel during initialization. 542 */ 543 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 544 545 /* 546 * Core HID Setup 547 */ 548 #define CONFIG_SYS_HID0_INIT 0x000000000 549 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 550 HID0_ENABLE_INSTRUCTION_CACHE | \ 551 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 552 #define CONFIG_SYS_HID2 HID2_HBE 553 554 /* 555 * MMU Setup 556 */ 557 #define CONFIG_HIGH_BATS 1 /* High BATs supported */ 558 559 /* DDR: cache cacheable */ 560 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ 561 | BATL_PP_RW \ 562 | BATL_MEMCOHERENCE) 563 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ 564 | BATU_BL_128M \ 565 | BATU_VS \ 566 | BATU_VP) 567 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 568 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 569 570 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 571 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ 572 | BATL_PP_RW \ 573 | BATL_CACHEINHIBIT \ 574 | BATL_GUARDEDSTORAGE) 575 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ 576 | BATU_BL_8M \ 577 | BATU_VS \ 578 | BATU_VP) 579 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 580 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 581 582 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 583 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE \ 584 | BATL_PP_RW \ 585 | BATL_MEMCOHERENCE) 586 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE \ 587 | BATU_BL_32M \ 588 | BATU_VS \ 589 | BATU_VP) 590 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE \ 591 | BATL_PP_RW \ 592 | BATL_CACHEINHIBIT \ 593 | BATL_GUARDEDSTORAGE) 594 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 595 596 /* Stack in dcache: cacheable, no memory coherence */ 597 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) 598 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR \ 599 | BATU_BL_128K \ 600 | BATU_VS \ 601 | BATU_VP) 602 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 603 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 604 605 /* PCI MEM space: cacheable */ 606 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI_MEM_PHYS \ 607 | BATL_PP_RW \ 608 | BATL_MEMCOHERENCE) 609 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI_MEM_PHYS \ 610 | BATU_BL_256M \ 611 | BATU_VS \ 612 | BATU_VP) 613 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 614 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 615 616 /* PCI MMIO space: cache-inhibit and guarded */ 617 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI_MMIO_PHYS \ 618 | BATL_PP_RW \ 619 | BATL_CACHEINHIBIT \ 620 | BATL_GUARDEDSTORAGE) 621 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI_MMIO_PHYS \ 622 | BATU_BL_256M \ 623 | BATU_VS \ 624 | BATU_VP) 625 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 626 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 627 628 #define CONFIG_SYS_IBAT6L 0 629 #define CONFIG_SYS_IBAT6U 0 630 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 631 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 632 633 #define CONFIG_SYS_IBAT7L 0 634 #define CONFIG_SYS_IBAT7U 0 635 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 636 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 637 638 #if defined(CONFIG_CMD_KGDB) 639 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 640 #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ 641 #endif 642 643 /* 644 * Environment Configuration 645 */ 646 647 #define CONFIG_ENV_OVERWRITE 648 649 #if defined(CONFIG_TSEC_ENET) 650 #define CONFIG_HAS_ETH0 651 #define CONFIG_HAS_ETH1 652 #endif 653 654 #define CONFIG_BAUDRATE 115200 655 656 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 657 658 #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ 659 #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ 660 661 #define CONFIG_EXTRA_ENV_SETTINGS \ 662 "netdev=eth0\0" \ 663 "consoledev=ttyS0\0" \ 664 "ramdiskaddr=1000000\0" \ 665 "ramdiskfile=ramfs.83xx\0" \ 666 "fdtaddr=780000\0" \ 667 "fdtfile=mpc8315erdb.dtb\0" \ 668 "usb_phy_type=utmi\0" \ 669 "" 670 671 #define CONFIG_NFSBOOTCOMMAND \ 672 "setenv bootargs root=/dev/nfs rw " \ 673 "nfsroot=$serverip:$rootpath " \ 674 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 675 "$netdev:off " \ 676 "console=$consoledev,$baudrate $othbootargs;" \ 677 "tftp $loadaddr $bootfile;" \ 678 "tftp $fdtaddr $fdtfile;" \ 679 "bootm $loadaddr - $fdtaddr" 680 681 #define CONFIG_RAMBOOTCOMMAND \ 682 "setenv bootargs root=/dev/ram rw " \ 683 "console=$consoledev,$baudrate $othbootargs;" \ 684 "tftp $ramdiskaddr $ramdiskfile;" \ 685 "tftp $loadaddr $bootfile;" \ 686 "tftp $fdtaddr $fdtfile;" \ 687 "bootm $loadaddr $ramdiskaddr $fdtaddr" 688 689 690 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 691 692 #endif /* __CONFIG_H */ 693