1 /* 2 * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. 3 * Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com 4 * 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 22 * MA 02111-1307 USA 23 */ 24 25 #ifndef __CONFIG_H 26 #define __CONFIG_H 27 28 /* 29 * High Level Configuration Options 30 */ 31 #define CONFIG_E300 1 /* E300 family */ 32 #define CONFIG_MPC83xx 1 /* MPC83xx family */ 33 #define CONFIG_MPC8308 1 /* MPC8308 CPU specific */ 34 #define CONFIG_MPC8308RDB 1 /* MPC8308RDB board specific */ 35 36 #define CONFIG_SYS_TEXT_BASE 0xFE000000 37 38 #define CONFIG_MISC_INIT_R 39 40 /* 41 * On-board devices 42 * 43 * TSEC1 is SoC TSEC 44 * TSEC2 is VSC switch 45 */ 46 #define CONFIG_TSEC1 47 #define CONFIG_VSC7385_ENET 48 49 /* 50 * System Clock Setup 51 */ 52 #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ 53 #define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN 54 55 /* 56 * Hardware Reset Configuration Word 57 * if CLKIN is 66.66MHz, then 58 * CSB = 133MHz, DDRC = 266MHz, LBC = 133MHz 59 * We choose the A type silicon as default, so the core is 400Mhz. 60 */ 61 #define CONFIG_SYS_HRCW_LOW (\ 62 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 63 HRCWL_DDR_TO_SCB_CLK_2X1 |\ 64 HRCWL_SVCOD_DIV_2 |\ 65 HRCWL_CSB_TO_CLKIN_4X1 |\ 66 HRCWL_CORE_TO_CSB_3X1) 67 /* 68 * There are neither HRCWH_PCI_HOST nor HRCWH_PCI1_ARBITER_ENABLE bits 69 * in 8308's HRCWH according to the manual, but original Freescale's 70 * code has them and I've expirienced some problems using the board 71 * with BDI3000 attached when I've tried to set these bits to zero 72 * (UART doesn't work after the 'reset run' command). 73 */ 74 #define CONFIG_SYS_HRCW_HIGH (\ 75 HRCWH_PCI_HOST |\ 76 HRCWH_PCI1_ARBITER_ENABLE |\ 77 HRCWH_CORE_ENABLE |\ 78 HRCWH_FROM_0X00000100 |\ 79 HRCWH_BOOTSEQ_DISABLE |\ 80 HRCWH_SW_WATCHDOG_DISABLE |\ 81 HRCWH_ROM_LOC_LOCAL_16BIT |\ 82 HRCWH_RL_EXT_LEGACY |\ 83 HRCWH_TSEC1M_IN_RGMII |\ 84 HRCWH_TSEC2M_IN_RGMII |\ 85 HRCWH_BIG_ENDIAN) 86 87 /* 88 * System IO Config 89 */ 90 #define CONFIG_SYS_SICRH (\ 91 SICRH_ESDHC_A_SD |\ 92 SICRH_ESDHC_B_SD |\ 93 SICRH_ESDHC_C_SD |\ 94 SICRH_GPIO_A_TSEC2 |\ 95 SICRH_GPIO_B_TSEC2_GTX_CLK125 |\ 96 SICRH_IEEE1588_A_GPIO |\ 97 SICRH_USB |\ 98 SICRH_GTM_GPIO |\ 99 SICRH_IEEE1588_B_GPIO |\ 100 SICRH_ETSEC2_CRS |\ 101 SICRH_GPIOSEL_1 |\ 102 SICRH_TMROBI_V3P3 |\ 103 SICRH_TSOBI1_V2P5 |\ 104 SICRH_TSOBI2_V2P5) /* 0x01b7d103 */ 105 #define CONFIG_SYS_SICRL (\ 106 SICRL_SPI_PF0 |\ 107 SICRL_UART_PF0 |\ 108 SICRL_IRQ_PF0 |\ 109 SICRL_I2C2_PF0 |\ 110 SICRL_ETSEC1_GTX_CLK125) /* 0x00000040 */ 111 112 /* 113 * IMMR new address 114 */ 115 #define CONFIG_SYS_IMMR 0xE0000000 116 117 /* 118 * SERDES 119 */ 120 #define CONFIG_FSL_SERDES 121 #define CONFIG_FSL_SERDES1 0xe3000 122 123 /* 124 * Arbiter Setup 125 */ 126 #define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth is 4 */ 127 #define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count is 4 */ 128 #define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC emergency priority is highest */ 129 130 /* 131 * DDR Setup 132 */ 133 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ 134 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 135 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 136 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 137 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \ 138 | DDRCDR_PZ_LOZ \ 139 | DDRCDR_NZ_LOZ \ 140 | DDRCDR_ODT \ 141 | DDRCDR_Q_DRN) 142 /* 0x7b880001 */ 143 /* 144 * Manually set up DDR parameters 145 * consist of two chips HY5PS12621BFP-C4 from HYNIX 146 */ 147 148 #define CONFIG_SYS_DDR_SIZE 128 /* MB */ 149 150 #define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 151 #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ 152 | 0x00010000 /* ODT_WR to CSn */ \ 153 | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) 154 /* 0x80010102 */ 155 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 156 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ 157 | (0 << TIMING_CFG0_WRT_SHIFT) \ 158 | (0 << TIMING_CFG0_RRT_SHIFT) \ 159 | (0 << TIMING_CFG0_WWT_SHIFT) \ 160 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ 161 | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ 162 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ 163 | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) 164 /* 0x00220802 */ 165 #define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \ 166 | (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \ 167 | (2 << TIMING_CFG1_ACTTORW_SHIFT) \ 168 | (5 << TIMING_CFG1_CASLAT_SHIFT) \ 169 | (6 << TIMING_CFG1_REFREC_SHIFT) \ 170 | (2 << TIMING_CFG1_WRREC_SHIFT) \ 171 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ 172 | (2 << TIMING_CFG1_WRTORD_SHIFT)) 173 /* 0x27256222 */ 174 #define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \ 175 | (4 << TIMING_CFG2_CPO_SHIFT) \ 176 | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ 177 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ 178 | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ 179 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ 180 | (5 << TIMING_CFG2_FOUR_ACT_SHIFT)) 181 /* 0x121048c5 */ 182 #define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \ 183 | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) 184 /* 0x03600100 */ 185 #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ 186 | SDRAM_CFG_SDRAM_TYPE_DDR2 \ 187 | SDRAM_CFG_32_BE) 188 /* 0x43080000 */ 189 190 #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */ 191 #define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \ 192 | (0x0232 << SDRAM_MODE_SD_SHIFT)) 193 /* ODT 150ohm CL=3, AL=1 on SDRAM */ 194 #define CONFIG_SYS_DDR_MODE2 0x00000000 195 196 /* 197 * Memory test 198 */ 199 #define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */ 200 #define CONFIG_SYS_MEMTEST_END 0x07f00000 201 202 /* 203 * The reserved memory 204 */ 205 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 206 207 #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ 208 #define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ 209 210 /* 211 * Initial RAM Base Address Setup 212 */ 213 #define CONFIG_SYS_INIT_RAM_LOCK 1 214 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ 215 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ 216 #define CONFIG_SYS_GBL_DATA_OFFSET \ 217 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 218 219 /* 220 * Local Bus Configuration & Clock Setup 221 */ 222 #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP 223 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 224 #define CONFIG_SYS_LBC_LBCR 0x00040000 225 226 /* 227 * FLASH on the Local Bus 228 */ 229 #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ 230 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 231 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 232 233 #define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ 234 #define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */ 235 #define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ 236 237 /* Window base at flash base */ 238 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 239 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) 240 241 #define CONFIG_SYS_BR0_PRELIM (\ 242 CONFIG_SYS_FLASH_BASE /* Flash Base address */ |\ 243 (2 << BR_PS_SHIFT) /* 16 bit port size */ |\ 244 BR_V) /* valid */ 245 #define CONFIG_SYS_OR0_PRELIM ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) \ 246 | OR_UPM_XAM \ 247 | OR_GPCM_CSNT \ 248 | OR_GPCM_ACS_DIV2 \ 249 | OR_GPCM_XACS \ 250 | OR_GPCM_SCY_15 \ 251 | OR_GPCM_TRLX \ 252 | OR_GPCM_EHTR \ 253 | OR_GPCM_EAD) 254 255 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 256 /* 127 64KB sectors and 8 8KB top sectors per device */ 257 #define CONFIG_SYS_MAX_FLASH_SECT 135 258 259 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 260 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 261 262 /* 263 * NAND Flash on the Local Bus 264 */ 265 #define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ 266 #define CONFIG_SYS_BR1_PRELIM ( CONFIG_SYS_NAND_BASE \ 267 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ 268 | BR_PS_8 /* Port Size = 8 bit */ \ 269 | BR_MS_FCM /* MSEL = FCM */ \ 270 | BR_V ) /* valid */ 271 #define CONFIG_SYS_OR1_PRELIM ( 0xFFFF8000 /* length 32K */ \ 272 | OR_FCM_CSCT \ 273 | OR_FCM_CST \ 274 | OR_FCM_CHT \ 275 | OR_FCM_SCY_1 \ 276 | OR_FCM_TRLX \ 277 | OR_FCM_EHTR ) 278 /* 0xFFFF8396 */ 279 280 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE 281 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) 282 283 #ifdef CONFIG_VSC7385_ENET 284 #define CONFIG_TSEC2 285 #define CONFIG_SYS_VSC7385_BASE 0xF0000000 286 #define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ 287 #define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ 288 /* Access window base at VSC7385 base */ 289 #define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE 290 /* Access window size 128K */ 291 #define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_128KB) 292 /* The flash address and size of the VSC7385 firmware image */ 293 #define CONFIG_VSC7385_IMAGE 0xFE7FE000 294 #define CONFIG_VSC7385_IMAGE_SIZE 8192 295 #endif 296 /* 297 * Serial Port 298 */ 299 #define CONFIG_CONS_INDEX 1 300 #define CONFIG_SYS_NS16550 301 #define CONFIG_SYS_NS16550_SERIAL 302 #define CONFIG_SYS_NS16550_REG_SIZE 1 303 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 304 305 #define CONFIG_SYS_BAUDRATE_TABLE \ 306 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 307 308 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 309 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 310 311 /* Use the HUSH parser */ 312 #define CONFIG_SYS_HUSH_PARSER 313 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " 314 315 /* Pass open firmware flat tree */ 316 #define CONFIG_OF_LIBFDT 1 317 #define CONFIG_OF_BOARD_SETUP 1 318 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 319 320 /* I2C */ 321 #define CONFIG_HARD_I2C /* I2C with hardware support */ 322 #define CONFIG_FSL_I2C 323 #define CONFIG_I2C_MULTI_BUS 324 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ 325 #define CONFIG_SYS_I2C_SLAVE 0x7F 326 #define CONFIG_SYS_I2C_NOPROBES {{0x51}} /* Don't probe these addrs */ 327 #define CONFIG_SYS_I2C_OFFSET 0x3000 328 #define CONFIG_SYS_I2C2_OFFSET 0x3100 329 330 331 /* 332 * Board info - revision and where boot from 333 */ 334 #define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39 335 336 /* 337 * Config on-board RTC 338 */ 339 #define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */ 340 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ 341 342 /* 343 * General PCI 344 * Addresses are mapped 1-1. 345 */ 346 #define CONFIG_SYS_PCIE1_BASE 0xA0000000 347 #define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000 348 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000 349 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 350 #define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000 351 #define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000 352 #define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 353 #define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000 354 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 355 356 /* enable PCIE clock */ 357 #define CONFIG_SYS_SCCR_PCIEXP1CM 1 358 359 #define CONFIG_PCI 360 #define CONFIG_PCIE 361 362 #define CONFIG_PCI_PNP /* do pci plug-and-play */ 363 364 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 365 #define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1 366 367 /* 368 * TSEC 369 */ 370 #define CONFIG_NET_MULTI 371 #define CONFIG_TSEC_ENET /* TSEC ethernet support */ 372 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 373 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) 374 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 375 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) 376 377 /* 378 * TSEC ethernet configuration 379 */ 380 #define CONFIG_MII 1 /* MII PHY management */ 381 #define CONFIG_TSEC1_NAME "eTSEC0" 382 #define CONFIG_TSEC2_NAME "eTSEC1" 383 #define TSEC1_PHY_ADDR 2 384 #define TSEC2_PHY_ADDR 1 385 #define TSEC1_PHYIDX 0 386 #define TSEC2_PHYIDX 0 387 #define TSEC1_FLAGS TSEC_GIGABIT 388 #define TSEC2_FLAGS TSEC_GIGABIT 389 390 /* Options are: eTSEC[0-1] */ 391 #define CONFIG_ETHPRIME "eTSEC0" 392 393 /* 394 * Environment 395 */ 396 #define CONFIG_ENV_IS_IN_FLASH 1 397 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ 398 CONFIG_SYS_MONITOR_LEN) 399 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 400 #define CONFIG_ENV_SIZE 0x2000 401 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 402 #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE 403 404 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 405 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 406 407 /* 408 * BOOTP options 409 */ 410 #define CONFIG_BOOTP_BOOTFILESIZE 411 #define CONFIG_BOOTP_BOOTPATH 412 #define CONFIG_BOOTP_GATEWAY 413 #define CONFIG_BOOTP_HOSTNAME 414 415 /* 416 * Command line configuration. 417 */ 418 #include <config_cmd_default.h> 419 420 #define CONFIG_CMD_DATE 421 #define CONFIG_CMD_DHCP 422 #define CONFIG_CMD_I2C 423 #define CONFIG_CMD_MII 424 #define CONFIG_CMD_NET 425 #define CONFIG_CMD_PCI 426 #define CONFIG_CMD_PING 427 428 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 429 430 /* 431 * Miscellaneous configurable options 432 */ 433 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 434 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 435 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 436 437 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ 438 439 /* Print Buffer Size */ 440 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) 441 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 442 /* Boot Argument Buffer Size */ 443 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 444 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 445 446 /* 447 * For booting Linux, the board info and command line data 448 * have to be in the first 256 MB of memory, since this is 449 * the maximum mapped by the Linux kernel during initialization. 450 */ 451 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ 452 453 /* 454 * Core HID Setup 455 */ 456 #define CONFIG_SYS_HID0_INIT 0x000000000 457 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 458 HID0_ENABLE_INSTRUCTION_CACHE | \ 459 HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) 460 #define CONFIG_SYS_HID2 HID2_HBE 461 462 /* 463 * MMU Setup 464 */ 465 466 /* DDR: cache cacheable */ 467 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ 468 BATL_MEMCOHERENCE) 469 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | \ 470 BATU_VS | BATU_VP) 471 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 472 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 473 474 /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ 475 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ 476 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 477 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | \ 478 BATU_VP) 479 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 480 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 481 482 /* FLASH: icache cacheable, but dcache-inhibit and guarded */ 483 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ 484 BATL_MEMCOHERENCE) 485 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | \ 486 BATU_VS | BATU_VP) 487 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ 488 BATL_CACHEINHIBIT | \ 489 BATL_GUARDEDSTORAGE) 490 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 491 492 /* Stack in dcache: cacheable, no memory coherence */ 493 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) 494 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ 495 BATU_VS | BATU_VP) 496 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 497 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 498 499 /* 500 * Environment Configuration 501 */ 502 503 #define CONFIG_ENV_OVERWRITE 504 505 #if defined(CONFIG_TSEC_ENET) 506 #define CONFIG_HAS_ETH0 507 #define CONFIG_HAS_ETH1 508 #endif 509 510 #define CONFIG_BAUDRATE 115200 511 512 #define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ 513 514 #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ 515 516 #define xstr(s) str(s) 517 #define str(s) #s 518 519 #define CONFIG_EXTRA_ENV_SETTINGS \ 520 "netdev=eth0\0" \ 521 "consoledev=ttyS0\0" \ 522 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 523 "nfsroot=${serverip}:${rootpath}\0" \ 524 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 525 "addip=setenv bootargs ${bootargs} " \ 526 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 527 ":${hostname}:${netdev}:off panic=1\0" \ 528 "addtty=setenv bootargs ${bootargs}" \ 529 " console=${consoledev},${baudrate}\0" \ 530 "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ 531 "addmisc=setenv bootargs ${bootargs}\0" \ 532 "kernel_addr=FE080000\0" \ 533 "fdt_addr=FE280000\0" \ 534 "ramdisk_addr=FE290000\0" \ 535 "u-boot=mpc8308rdb/u-boot.bin\0" \ 536 "kernel_addr_r=1000000\0" \ 537 "fdt_addr_r=C00000\0" \ 538 "hostname=mpc8308rdb\0" \ 539 "bootfile=mpc8308rdb/uImage\0" \ 540 "fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \ 541 "rootpath=/opt/eldk-4.2/ppc_6xx\0" \ 542 "flash_self=run ramargs addip addtty addmtd addmisc;" \ 543 "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ 544 "flash_nfs=run nfsargs addip addtty addmtd addmisc;" \ 545 "bootm ${kernel_addr} - ${fdt_addr}\0" \ 546 "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ 547 "tftp ${fdt_addr_r} ${fdtfile};" \ 548 "run nfsargs addip addtty addmtd addmisc;" \ 549 "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ 550 "bootcmd=run flash_self\0" \ 551 "load=tftp ${loadaddr} ${u-boot}\0" \ 552 "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) \ 553 " +${filesize};era " xstr(CONFIG_SYS_MONITOR_BASE) \ 554 " +${filesize};cp.b ${fileaddr} " \ 555 xstr(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \ 556 "upd=run load update\0" \ 557 558 #endif /* __CONFIG_H */ 559